Commit graph

229 commits

Author SHA1 Message Date
Sriram R
7b2ca5cf0d hostapd: Reset channel switch parameters on interface disable
Previously, when an AP interface was disabled through a control
interface DISABLE command during a channel switch window, the interface
could not be reenabled due to beacon setup failure (which validates if
CSA is in progress).

Fix this by clearing channel switch parameters while disabling the
hostapd interface.

Signed-off-by: Sriram R <srirrama@codeaurora.org>
2018-10-19 21:26:03 +03:00
Hu Wang
567df5501c Re-configure WEP keys on hostapd interface re-enable
This allows WEP mode AP to be re-enabled automatically after external
ifconfig down + up on netdev used by hostapd.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-08-21 18:50:12 +03:00
Martin Willi
4a0e011560 AP: Fix HT 20/40 co-ex transition timer cancellation on iface removal
When removing an interface, hostapd_bss_deinit() frees all associated
STAs. If any of the stations is 40MHz intolerant, the cleanup invokes
ht40_intolerant_remove(), that in turn registers a 20->40MHz transition
timer for the last station (ap_ht2040_timeout() function). That timer is
never canceled; once it executes, the interface is gone, most likely
resulting in a segfault when referencing it.

While hostapd_interface_deinit() cancels the transition timer, it does
so before cleaning up STAs. Move the cancellation after STA cleanup to
cancel any timer that was registered during that operation.

Signed-off-by: Martin Willi <martin@strongswan.org>
2018-06-12 21:45:10 +03:00
Sathishkumar Muruganandam
bda9c08596 hostapd: Fix CHAN_SWITCH command for VHT20 and VHT40
Previously, hostapd CHAN_SWITCH command did not effect VHT configuration
for the following:

When VHT is currently disabled (ieee80211ac=0),

1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
                sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht

====> Comes up in HT40

2. hostapd_cli -p /var/run/hostapd chan_switch 10 5765 \
                sec_channel_offset=-1 center_freq1=5775 bandwidth=40 vht

====> Comes up in HT40

3. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
                                                  bandwidth=20 vht

====> Comes up in HT20

When VHT is currently enabled (ieee80211ac=1),

1. hostapd_cli -p /var/run/hostapd chan_switch 10 5180 \
                sec_channel_offset=1 center_freq1=5190 bandwidth=40 ht

====> Comes up in VHT40

2. hostapd_cli -p /var/run/hostapd chan_switch 10 5200 center_freq1=5200 \
                                                  bandwidth=20 ht

====> Comes up in VHT20

This is since VHT config from chan_switch is processed only for
bandwidths 80 and above (80P80, 160) and for VHT20, VHT40 cases, only
NLA chan type and chan width are updated.

There is no NL attribute for determining if it is HT or VHT for
bandwidths 20 & 40 and currently they are updated as HT20, HT40 (+ or -
depending on offset). Same is notified back via
NL80211_CMD_CH_SWITCH_NOTIFY.

Instead of adding new NL attribute for tracking HT/VHT enabled config,
we are adding new hostapd VHT config parameter to save the chan_switch
config and use only for chan_switch case of VHT20 and VHT40.

Tested with all combinations of chan_switch (noHT->20->40->80->) HT/VHT
and confirmed to be working.

Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
2018-05-16 01:16:54 +03:00
Jouni Malinen
f456940ef3 HS 2.0: CoA-Request processing for Terms and Conditions filtering
Extend RADIUS DAS to support CoA-Request packets for the case where the
HS 2.0 Terms And Conditions filtering VSA is used to remove filtering.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-25 12:57:46 +03:00
Tova Mussai
c4315e6620 AP: Handle AP initalization failure in async flow
When AP initialization is completed in a callback (e.g., OBSS scan),
wpa_supplicant_deinit_ap() is not called in case of failure. Fix this by
calling setup_complete_cb in case of failure, too, which in turn calls
wpa_supplicant_deinit_ap() if needed.

Signed-off-by: Tova Mussai <tova.mussai@intel.com>
2018-04-20 00:48:49 +03:00
Jouni Malinen
4d6eb9f2e2 Fix hostapd wmm_enabled setup on config reload path
If there is no explicit wmm_enabled parameter in the configuration
(i.e., conf->wmm_enabled == -1), the configuration reload path needs to
initialize conf->wmm_enabled based on iconf->ieee80211n in
hostapd_reload_bss() similarly to what is done in the initial startup
case in hostapd_setup_bss().

This fixes issues with RSN capabilities being set incorrectly when WMM
is supposed to get enabled and unexpectedly enabling WMM when it is not
supposed to be enabled (HT disabled). Either of these issues could show
up when asking hostapd to reload the configuration file (and when that
file does not set wmm_enabled explicitly).

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-04-06 23:29:11 +03:00
Jouni Malinen
2f1357fb62 FILS: Accept another (Re)Association Request frame during an association
The previous implementation ended up starting a new EAPOL-Key 4-way
handshake if the STA were to attempt to perform another association.
This resulted in immediate disconnection since the PTK was not ready for
configuring FILS TK at the point when EAPOL-Key msg 1/4 is sent out.
This is better than alloing the association to continue with the same TK
reconfigured, but not really ideal.

Address this potential sequence by not starting a new 4-way handshake on
the additional association attempt. Instead, allow the association to
complete, but do so without reconfiguring the TK to avoid potential
issues with PN reuse with the same TK.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-10-16 02:03:47 +03:00
Jouni Malinen
c53eb94616 OWE: Remove forgotten developer debug prints
These were used during initial implementation testing and were not
supposed to get committed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-11 23:43:59 +03:00
Jouni Malinen
a891388184 OWE: Transition mode information based on BSS ifname
The owe_transition_bssid and owe_transition_ssid parameters can now be
replace with owe_transition_ifname to clone the BSSID/SSID information
automatically in case the same hostapd process manages both the OWE and
open BSS for transition mode.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-09 13:39:23 +03:00
Jouni Malinen
9c2b8204e6 DPP: Integration for hostapd
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-19 21:13:17 +03:00
Michael Braun
50bd8e0a90 FT: Replace inter-AP protocol with use of OUI Extended Ethertype
Replace the previously used extension of IEEE 802.11 managed Ethertype
89-0d (originally added for Remote Request/Response in IEEE 802.11r)
with Ethertype 88-b7 (OUI Extended EtherType) for FT inter-AP
communication. The new design uses a more properly assigned identifier
for the messages.

This assigns the OUI 00:13:74 vendor-specific subtype 0x0001 for the new
hostapd AP-to-AP communication purposes. Subtypes 1 (PULL), 2 (RESP),
and 3 (PUSH) are also assigned in this commit for the R0KH-R1KH
protocol.

This breaks backward compatibility, i.e., hostapd needs to be updated on
all APs at the same time to allow FT to remain functional.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2017-05-03 18:30:31 +03:00
Michael Braun
c5fee1604b FT: Schedule wpa_ft_rrb_rx() through eloop in intra-process communication
With AP-AP communication, when hapd0 sends a packet, hapd1 can receive
it immediately and send a response. But hapd0 will only read and process
the response after it has returned from the sending context, that is
entered eloop again. So one does not need to consider the RX function of
the reply to run for the request sending hapd before the send calling
function has returned.

Previously, with intra-process communication, the packet is not
scheduled through eloop. Thus the RX handler of the reply might be run
while the sending context of the original request has not returned.
This might become problematic, e.g., when deferring a management frame
processing until an RRB response is received and then have the request
restarted and finished before the original request handling has been
stopped.

I'm not aware of any concrete bug this is currently triggering but came
across it while thinking of FT RRB AP-AP sequence numbering.

I think the non-eloop scheduling approach might be error-prone and thus
propose to model it more closely to the way the message would be
received from a socket. Additionally, this ensures that the tests model
AP-AP communication more closely to real world.

Solution: queue these packets through eloop.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2017-04-01 12:51:05 +03:00
Johannes Berg
a1f11e34c4 Use os_memdup()
This leads to cleaner code overall, and also reduces the size
of the hostapd and wpa_supplicant binaries (in hwsim test build
on x86_64) by about 2.5 and 3.5KiB respectively.

The mechanical conversions all over the code were done with
the following spatch:

    @@
    expression SIZE, SRC;
    expression a;
    @@
    -a = os_malloc(SIZE);
    +a = os_memdup(SRC, SIZE);
    <...
    if (!a) {...}
    ...>
    -os_memcpy(a, SRC, SIZE);

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-07 13:19:10 +02:00
Jouni Malinen
4c803dfcd7 ACS: Fix memory leak if interface is disabled during scan
The survey data was not freed if hostapd interface got disabled during
an ACS scan.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-03-04 17:30:15 +02:00
Jouni Malinen
57a2aacabf Add option to disable broadcast deauth in hostapd on AP start/stop
The new broadcast_deauth parameter can be used to disable sending of the
Deauthentication frame whenever AP is started or stopped. The default
behavior remains identical to the past behavior (broadcast_deauth=1).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
21ed24f5ad hostapd: Fix potential mesh-related change from impacting non-mesh cases
Commit 01e2231fdc ('hostapd: Skip some
configuration steps for mesh cases') removed some operations based on
hapd->iface->mconf being NULL. This was within #ifdef CONFIG_MESH, so it
should not impact hostapd, but it can impact AP mode with
wpa_supplicant. That does not sound intentional, so make these
conditional on hapd->conf->mesh being enabled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-26 12:05:40 +02:00
Jouni Malinen
db5e53cb06 mesh: Fix struct hostapd_data initialization
The local custom version of allocating and initializing struct
hostapd_data within wpa_supplicant_mesh_init() is problematic. This has
already missed couple of initialization steps that are required. Instead
of trying to remember to keep this up to date, use
hostapd_alloc_bss_data() so that there is only one place for this
initialization.

This is fixing a recent issue where FILS HLP started using
hapd->dhcp_server and expected that to be initialized to -1. For the
mesh case, that did not happen and when removing the interface, the FILS
HLP implementation ended up unregistering eloop socket for
hapd->dhcp_server (= 0). This could result in missing socket callbacks
for an arbitrary socket.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-02-04 22:17:54 +02:00
Jouni Malinen
91d91abf6f FILS: DHCP relay for HLP requests
The new dhcp_server configuration parameter can now be used to configure
hostapd to act as a DHCP relay for DHCPDISCOVER messages received as
FILS HLP requests. The dhcp_rapid_commit_proxy=1 parameter can be used
to configure hostapd to convert 4 message DHCP exchange into a 2 message
exchange in case the DHCP server does not support DHCP rapid commit
option.

The fils_hlp_wait_time parameter can be used to set the time hostapd
waits for an HLP response. This matches the dot11HLPWaitTime in IEEE Std
802.11ai-2016.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-01 18:17:39 +02:00
Jouni Malinen
f56877414c Do not add own BSS in neighbor report with invalid op_class/channel
Verify that ieee80211_freq_to_channel_ext() succeeds before adding the
own BSS in the neighbor report.

Signed-off-by: Jouni Malinen <j@w1.fi>
2017-01-03 15:18:30 +02:00
Jouni Malinen
1dfd25a68a Fix hostapd SIGHUP processing before interface is enabled
It was possible to try to do driver operations before the driver
interface had been initialized when processing a SIGHUP signal. This
would result in NULL pointer dereference. Fix this by skipping the steps
when SIGHUP is issued before the interface is enabled.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-12-27 11:16:51 +02:00
Daisuke Niwa
655dc4a432 Send "TERMINATING" event from hostapd
hostapd didn't send "TERMINATING" event when stopped by
SIGTERM. Android handles this event to stop monitor thread.

This commit adds "TERMINATING" event same as with wpa_supplicant.

Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sonymobile.com>
2016-12-12 20:32:28 +02:00
Sam Tannous
08032c7418 Remove inactivity timeout for wired interfaces
We should unconditionally remove inactivity timers for wired network
cases. This commit checks for this after a new station association:

   hapd->iface->drv_flags & WPA_DRIVER_FLAGS_WIRED

and then cancels the timeout and does not register a new one.

It prints out a debug message like this:

1476740180.276286: IEEE 802.1X: 00:02:00:00:00:07 CTRL_DIR entering
state FORCE_BOTH
1476740180.276295: hostapd_new_assoc_sta: canceled wired ap_handle_timer
timeout for 00:02:00:00:00:07

This was tested on a debian jessie amd64 system with a configured 120
second inactivity timer and the session did not timeout.

Signed-off-by: Sam Tannous <stannous@cumulusnetworks.com>
2016-12-04 20:38:45 +02:00
Ilan Peer
4ec1fd8e42 FT: Differentiate between FT for station and for AP in build
Previously, CONFIG_IEEE80211R enabled build that supports FT for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode FT is required and there is no need for AP mode FT.

Add support to differentiate between station mode FT and AP mode FT in
wpa_supplicant builds by adding CONFIG_IEEE80211R_AP that should be used
when AP mode FT support is required in addition to station mode FT. This
allows binary size to be reduced for builds that require only the
station side FT functionality.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2016-10-29 22:14:54 +03:00
Beni Lev
f0259c3f68 hostapd: Fix own wide bandwidth subelement generation (neighbor report)
The Channel Center Frequency Segment subfields use the channel index
instead of frequency in MHz.

Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-10-29 22:03:43 +03:00
David Spinadel
451a27b1ad hostapd: Add a configuration to set an AP as stationary
Add a configuration option in hostapd.conf and in neighbor report that
sets an AP as stationary. To enable this option on the current AP set
the config option stationary_ap to 1. To set a neighbor entry to be
marked as stationary add the word stat to the SET_NEIGHBOR command. This
option tells hostapd to send LCI data even if it is older than requested
by max age subelement in RRM request.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-10-29 19:16:47 +03:00
Denton Gentry
442819406c taxonomy: Store Probe Request frames in hostapd_sta_info
A weakness in the initial client taxonomy mechanism is from storing both
the Probe and Associate in struct sta_info. struct sta_info is created
after a client associates (or starts authentication frame exchange),
which means that any Probe Request frames sent prior to association are
not retained. The Associate Request frame has to be seen, and then
another Probe Request frame after association, before we have a
signature for the client.

Most clients send lots of Probe Request frames (lots and lots and lots
of Probes, actually), but a few do not. ChromeOS is notably sparing in
sending Probe Request frames, it can take a long time before a signature
for a ChromeOS device is available.

Store the most recent Probe Request frame in struct hostapd_sta_info
tracking list. When a struct sta_info is created, move the Probe Request
frame information from struct hostapd_sta_info to struct sta_info.

Signed-off-by: dgentry@google.com (Denton Gentry)
Signed-off-by: denny@geekhold.com (Denton Gentry)
Signed-off-by: rofrankel@google.com (Richard Frankel)
Signed-off-by: richard@frankel.tv (Richard Frankel)
2016-09-22 00:45:24 +03:00
Jouni Malinen
5e993390f6 Initialize iface->sta_seen on allocation
Previously, struct hostapd_iface sta_seen list head was initialized only
when completing interface setup. This left a window for operation that
could potentially iterate through the list before the list head has been
initialized. While the existing code checked iface->num_sta_seen to
avoid this case, it is much cleaner to initialize the list when struct
hostapd_iface is allocated to avoid any accidental missing of the extra
checks before list iteration.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-09-22 00:45:24 +03:00
Jouni Malinen
f2f8616e80 Initialize hapd->nr_db in hostapd_alloc_bss_data()
Previously, this was initialized in hostapd_setup_bss() which made it
possible for a REMOVE_NEIGHBOR control interface command to be issued
prior to the list head pointers having been set. That resulted in a NULL
pointer dereference. Fix this by initializing the list head at the time
the data structure gets allocated.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-22 17:44:05 +03:00
Nick Lowe
42d30e9ea0 Add a require_message_authenticator configuration option
This can be used to mandate the presence of the Message-Authenticator
attribute on CoA/Disconnect-Request packets.

Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
2016-08-08 00:36:17 +03:00
Jouni Malinen
9c10be3f71 mesh: Fix error path handling in init OOM cases
hostapd deinit functions were not ready to handle a case where the data
structures were not fully initialized. Make these more robust to allow
wpa_supplicant mesh implementation to use the current deinit design in
OOM error cases without causing NULL pointer dereferences.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-05-30 01:05:16 +03:00
David Spinadel
f4f185a224 hostapd: Add LCI request
Add a hostapd control interface command REQ_LCI to request LCI from an
associated station using radio measurement.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-04-17 12:29:12 +03:00
David Spinadel
061269b316 hostapd: Add own neighbor report data to neighbor database
Add own neighbor report data to neighbor database based on local LCI and
location civic data.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-04-16 21:05:40 +03:00
David Spinadel
9b4b226426 hostapd: Add a database of neighboring APs
Add a configurable neighbor database that includes the content of
Nighbor Report element, LCI and Location Civic subelements and SSID.

All parameters for a neighbor must be updated at once; Neighbor Report
element and SSID are mandatory, LCI and civic are optional. The age of
LCI is set to the time of neighbor update.

The control interface API is:
SET_NEIGHBOR <BSSID> <ssid=SSID> <nr=data> [lci=<data>] [civic=<data>]

To delete a neighbor use:
REMOVE_NEIGHBOR <BSSID> <SSID>

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-04-16 21:05:40 +03:00
Roy Marples
45e3fc72c6 Find correct driver for interface additions/removals
Interface additions/removals are not guaranteed to be for the driver
listening to the kernel events. As such, send the events to
wpa_supplicant_event_global() which can then pick the correct interface
registered with wpa_supplicant to send the event to.

Signed-off-by: Roy Marples <roy@marples.name>
2016-03-22 17:41:37 +02:00
Eliad Peller
6448e06415 hostapd: Allow use of driver-generated interface addresses
Add a new 'use_driver_iface_addr' configuration parameter to allow use
of the default interface address generated by the driver on interface
creation. This can be useful when specific MAC addresses were allocated
to the device and we want to use them for multi-BSS operation.

Signed-off-by: Eliad Peller <eliad@wizery.com>
2016-03-06 20:00:40 +02:00
Janusz Dziedzic
56885eecf4 hostapd: Add UDP support for ctrl_iface
Add UDP support for ctrl_iface:

New config option could be set:
CONFIG_CTRL_IFACE=udp
CONFIG_CTRL_IFACE=udp-remote
CONFIG_CTRL_IFACE=udp6
CONFIG_CTRL_IFACE=udp6-remote

And hostapd_cli usage:
hostapd_cli -i localhost:8877

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2016-03-05 17:44:37 +02:00
Jouni Malinen
902c07a7af Replace hostapd_mac_comp_empty() with is_zero_ether_addr()
There is no need to maintain two implementations of the functionality.
is_zero_ether_addr() is easier to understand, so use it.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-02-28 20:11:58 +02:00
Michael Braun
d48d1b88d0 FT: Use BSSID as r1_key_holder if no value is configured
r1_key_holder is an identifier that was always set to zero if unless
configured before.

See 11.6.1.7.4 of IEEE Std 802.11-2012 which reads
 "R1KH-ID is a MAC address of the holder of the PMK-R1 in the
  Authenticator of the AP"
See 12.2.2 of IEEE Std 802.11-2012 which reads
 "Each R0KH-ID and R1KH-ID is assumed to be expressed as a unique
  identifier within the mobility domain."
 "The R1KH-ID shall be set to a MAC address of the physical entity
  that stores the PMK-R1 ..."

Defaulting this to BSSID is a more reasonable value since we have not
rejected the missing r1_key_holder as invalid configuration.

Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
2016-02-28 17:56:42 +02:00
Nick Lowe
1492fbb90c Print Acct-Session-Id and Acct-Multi-Session-Id 64-bit values
These are now 64-bit variables and the printf formats and type casts
need to be updated to match.

Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
2016-02-18 20:58:21 +02:00
Nick Lowe
d72a00539c RADIUS: Use more likely unique accounting Acct-{,Multi-}Session-Id
Rework the Acct-Session-Id and Acct-Multi-Session-Id implementation to
give better global and temporal uniqueness. Previously, only 32-bits of
the Acct-Session-Id would contain random data, the other 32-bits would
be incremented. Previously, the Acct-Multi-Session-Id would not use
random data. Switch from two u32 variables to a single u64 for the
Acct-Session-Id and Acct-Multi-Session-Id. Do not increment, this serves
no legitimate purpose. Exclusively use os_get_random() to get quality
random numbers, do not use or mix in the time. Inherently take a
dependency on /dev/urandom working properly therefore. Remove the global
Acct-Session-Id and Acct-Multi-Session-Id values that serve no
legitimate purpose.

Signed-off-by: Nick Lowe <nick.lowe@lugatech.com>
2016-02-06 17:10:19 +02:00
Jouni Malinen
03269d558a AP: Print interface name in more STA events
This makes it easier to follow a debug log from a hostapd process that
manages multiple interfaces.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-01-15 19:32:49 +02:00
Jouni Malinen
9e8fde2134 AP: Fix Deauth/Disassoc TX status timeout handling
The ap_sta_deauth_cb and ap_sta_disassoc_cb eloop timeouts are used to
clear a disconnecting STA from the kernel driver if the STA did not ACK
the Deauthentication/Disassociation frame from the AP within two
seconds. However, it was possible for a STA to not ACK such a frame,
e.g., when the disconnection happened due to hostapd pruning old
associations from other BSSes and the STA was not on the old channel
anymore. If that same STA then started a new authentication/association
with the BSS, the two second timeout could trigger during this new
association and result in the STA entry getting removed from the kernel.

Fix this by canceling these eloop timeouts when receiving an indication
of a new authentication or association.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-01-15 19:32:49 +02:00
Srinivasa Duvvuri
053693d266 hostapd: Add feature to start all interfaces at the same time in sync
When multiple interfaces across mutiple radios are started using a
single instance of hostapd, they all come up at different times
depending upon how long the ACS and HT scan take on each radio. This
will result in stations (that already have the AP profile) associating
with the first interfaces that comes up. For example in a dual band
radio case (2G and 5G) with ACS enabled, 2G always comes up first
because the ACS scan takes less time on 2G and this results in all
stations associating with the 2G interface first.

This feature brings up all the interfaces at the same time. The list of
interfaces specified via hostapd.conf files on the command line are all
marked as sync interfaces. All the interfaces are synchronized in
hostapd_setup_interface_complete().

This feature is turned on with '-S' commmand line option.

Signed-off-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
2015-10-28 19:47:17 +02:00
Andrei Otcheretianski
fa53d74c9e Handle VHT operating classes correctly
Fix and extend the ieee80211_freq_to_channel_ext() function to deal
correctly with VHT operating classes (128, 129, 130).

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-10-03 21:35:08 +03:00
Luciano Coelho
7d82170aba Set channel and operating class in hostapd_fill_csa_settings()
The CSA channel and operating class values need to be set for all types
of channel switch (i.e., either if it's triggered by the control
interfaces or due to the GO-follows-STA flow). To do so, move the code
that sets them from the GO-follows-STA flow to the more generic
hostapd_fill_csa_settings() function.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
2015-10-03 21:26:23 +03:00
Luciano Coelho
d308a44fcc Use ieee80211_freq_to_chan() when getting segment indices
The hostapd_hw_get_channel() function can't be used to convert center
frequencies to channel numbers, because the hw mode lists don't have all
the center frequencies. The hw mode lists have the main channel
frequencies and flags to indicate the channel topography.

For instance, channel 5805 with VHT80- has the channel center frequency
segment 0 at 5775. This segment is only indicated indirectly in the hw
mode list by the HOSTAPD_CHAN_VHT_50_30 flag. The hw mode list doesn't
have any elements with frequency 5775 to allow the conversion to a
channel number. Thus, we need to use ieee80211_freq_to_chan() instead.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
2015-10-03 21:19:09 +03:00
Ilan Peer
4e0ab656d2 Move hostapd_csa_in_progress() to hostapd.c
Move hostapd_csa_in_progress() to hostapd.{h,c} so it can be used
for contexts other than DFS.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-10-03 20:19:06 +03:00
Andrei Otcheretianski
6315bfdba2 Add support for eCSA
Extended channel switch provides an ability to switch between operating
classes and is required for P2P Devices by the P2P specification when
switching in 5 GHz.

When the operating class is provided for channel switch, the AP/P2P GO
will use eCSA IE in addition to the regular CSA IE both on 2.4 GHz and 5
GHz bands.

Transitions between different hw_modes are not supported.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-10-03 20:00:50 +03:00
Andrei Otcheretianski
366179d218 nl80211: Suppport multiple CSA counters
Channel switch may be performed using both CSA and eCSA IEs together.
This may happen, for example with a P2P GO on band A with legacy
clients. Extend driver API to support up to 2 CSA counters.

This patch also includes the required implementation for nl80211.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-10-03 19:56:08 +03:00