Commit graph

29 commits

Author SHA1 Message Date
Jouni Malinen
39b97072b2 Add support for Time Advertisement
This adds preliminary support for IEEE 802.11v Time Advertisement
mechanism with UTC TSF offset.
2011-10-18 00:24:16 +03:00
Jouni Malinen
4b2a77aba2 Interworking: Add support for configuring Roaming Consortium List 2011-10-17 23:55:50 +03:00
Jouni Malinen
b83e3e93c8 IEEE 802.11u: Add configuration and advertisement for Interworking 2011-10-16 23:55:34 +03:00
Jouni Malinen
697cd03fc2 AP: Set pairwise/group cipher for non-WPA modes
This is needed to avoid confusing configuration in some nl80211
drivers that the new AP mode configuration alternatives for
setting security policy.
2011-09-15 15:02:59 +03:00
Jouni Malinen
cb465555d4 Allow PMKSA caching to be disabled on Authenticator
A new hostapd configuration parameter, disable_pmksa_caching=1, can now
be used to disable PMKSA caching on the Authenticator. This forces the
stations to complete EAP authentication on every association when WPA2
is being used.
2011-07-05 17:13:04 +03:00
Jouni Malinen
fa5165586f WPS: Add a workaround for Windows 7 capability discovery for PBC
Windows 7 uses incorrect way of figuring out AP's WPS capabilities by
acting as a Registrar and using M1 from the AP. The config methods
attribute in that message is supposed to indicate only the configuration
method supported by the AP in Enrollee role, i.e., to add an external
Registrar. For that case, PBC shall not be used and as such, the
PushButton config method is removed from M1 by default. If pbc_in_m1=1
is included in the configuration file, the PushButton config method is
left in M1 (if included in config_methods parameter) to allow Windows 7
to use PBC instead of PIN (e.g., from a label in the AP).
2011-05-17 19:53:02 +03:00
Jouni Malinen
cd9fc7869a hostapd: Add testing mode for RSN element extensions
CFLAGS += -DCONFIG_RSN_TESTING in .config and rsn_testing=1 in
hostapd.conf can now be used to enable a testing mode that adds
extensions to RSN element. This can be used to check whether
station implementations are incompatible with future extensions
to the RSN element.
2011-03-21 13:59:05 +02:00
Johannes Berg
2f646b6e83 WPS: Store (secondary) device type as binary
Instead of converting back and forth from the string representation,
always use the binary representation internally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-17 18:50:22 +02:00
Shan Palanisamy
d7956add9c FT: Make FT-over-DS configurable (hostapd.conf ft_over_ds=0/1) 2011-03-06 14:31:42 +02:00
Helmut Schaa
f39b07d7ed hostapd: Allow coexistance of HT BSSes with WEP/TKIP BSSes
In multi BSS setups it wasn't possible to set up an HT BSS in
conjunction with a WEP/TKIP BSS. HT needed to be turned off entirely
to allow WEP/TKIP BSSes to be used.

In order to allow HT BSSes to coexist with non-HT WEP/TKIP BSSes add a
new BSS conf attribute "disable_11n" which disables HT capabilities on a
single BSS by suppressing HT IEs in the beacon and probe response
frames. Furthermore, mark all STAs associated to a WEP/TKIP BSS as
non-HT STAs. The disable_11n parameter is used internally; no new entry
is parsed from hostapd.conf.

This allows a non-HT WEP/TKIP BSS to coexist with a HT BSS without
having to disable HT mode entirely. Nevertheless, all STAs associated to
the WEP/TKIP BSS will only be served as if they were non-HT STAs.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
2011-02-21 17:27:16 +02:00
Jouni Malinen
2944824315 hostapd: Add require_ht configuration parameter
This can be used to configure hostapd to reject association with
any station that does not support HT PHY.
2011-02-09 15:08:47 +02:00
Johannes Berg
d2da224948 AP: Enable WMM with default parameters by default for HT
If WMM is not disabled explicitly (wmm_enabled=0 in hostapd.conf),
enable WMM automatically whenever HT (ieee80211n) is enabled. Use
the default WMM parameters for AP TX queues and the EDCA parameters
advertised for stations in WMM IE if no overriding values are
included in the configuration.
2011-02-01 14:34:12 +02:00
Jouni Malinen
1161ff1ef5 hostapd: Allow TDLS use to be prohibited in the BSS
tdls_prohibit=1 and tdls_prohibit_chan_switch=1 and now be used to
disable use of TDLS or TDLS channel switching in the BSS using
extended cabilities IE as defined in IEEE 802.11z.
2011-01-28 19:21:59 +02:00
Johannes Berg
0d7e5a3a29 Allow AP mode to disconnect STAs based on low ACK condition
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-12-28 17:15:01 +02:00
Yogesh Ashok Powar
6950b2caa8 hostapd: Prohibit WEP configuration when HT is enabled
WFA 11n testing does not allow WEP when IEEE 802.11n is enabled.
Reject such combination when parsing hostapd configuration file.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
2010-11-09 16:49:03 +02:00
Felix Fietkau
d3b4286967 Allow client isolation to be configured (ap_isolate=1)
Client isolation can be used to prevent low-level bridging of frames
between associated stations in the BSS. By default, this bridging is
allowed.
2010-11-09 16:27:15 +02:00
Felix Fietkau
d38ae2ea85 Add bridge handling for WDS STA interfaces
By default, add them to the configured bridge of the AP interface
(if present), but allow the user to specify a separate bridge.
2010-11-09 16:12:42 +02:00
Jouni Malinen
7e3c178142 Remove unused TX queue parameters related to Beacon frames
These are not used by any driver wrapper, i.e., only the four
data queues (BK, BE, VI, VO) are configurable. Better remove these
so that there is no confusion about being able to configure
something additional.
2010-11-05 01:23:17 +02:00
Dmitry Shmidt
ae6e1bee67 Add WPA_IGNORE_CONFIG_ERRORS option to continue in case of bad config
This is an option to continue with wpa_supplicant and hostapd even if
config file has errors. The problem is that these daemons are the best
"candidates" for the config change, so if they can not start because
config file was let's say corrupted, you can not fix it easily.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2010-10-31 12:38:49 +02:00
Jouni Malinen
f61039c75f WPS 2.0: Disable WPS if ignore_broadcast_ssid or WEP is used
These combinations are disallowed in WPS 2.0 (and do not work well
(or at all) with many deployed WPS 1.0 devices either).
2010-09-24 15:17:03 -07:00
Dan Harkins
df684d82ff EAP-pwd: Add support for EAP-pwd server and peer functionality
This adds an initial EAP-pwd (RFC 5931) implementation. For now,
this requires OpenSSL.
2010-09-14 21:51:40 -10:00
Jouni Malinen
962473c136 P2P: Add preliminary P2P Manager AP support for hostapd 2010-09-09 07:17:18 -07:00
Jouni Malinen
7f6ec672ea EAP server: Add support for configuring fragment size 2010-07-20 22:56:10 -07:00
Yogesh Ashok Powar
721abef9b3 Allow advertising of U-APSD functionality in Beacon
hostapd does not implement UAPSD functionality. However, if U-APSD
functionality is implemented outside hostapd, add support to advertise
the functionality in beacon.

Signed-off-by: yogeshp@marvell.com
2010-04-11 11:32:15 +03:00
Jouni Malinen
9a8d8b3db5 Close config file on error path 2010-01-09 22:29:41 +02:00
Jouni Malinen
6226e38d00 Rename some src/ap files to avoid duplicate file names
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
2009-12-26 00:05:40 +02:00
Jouni Malinen
1057d78eb8 Move generic AP functionality implementation into src/ap
This code can be shared by both hostapd and wpa_supplicant and this
is an initial step in getting the generic code moved to be under the
src directories. Couple of generic files still remain under the
hostapd directory due to direct dependencies to files there. Once the
dependencies have been removed, they will also be moved to the src/ap
directory to allow wpa_supplicant to be built without requiring anything
from the hostapd directory.
2009-12-25 01:12:50 +02:00
Jouni Malinen
d3b86aed73 Move wpa_drivers dependency into config_file.c
This cleans up config.o from driver wrapper dependencies.
2009-12-24 22:50:17 +02:00
Jouni Malinen
41d719d6e0 Move hostapd configuration parser into separate file
config.c includes now only the generic helper functions that are needed
both for hostapd and the AP mode operations in wpa_supplicant.
hostapd/config_file.c is only needed for hostapd.
2009-12-24 21:05:40 +02:00