This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The roam D-Bus and ROAM control itnerface commands flip the reassociate
bit before calling wpa_supplicant_connect(). wpa_supplicant connect
eventually aborts ongoing scans (if any), which causes scan results to
be reported. Since the reassociate bit is set, this will trigger a
connection attempt based on the aborted scan's scan results and cancel
the initial connetion request. This often causes wpa_supplicant to
reassociate to the same AP it is currently associated to instead of the
explicitly requested roaming target.
Add a roam_in_progress flag to indicate that we're currently attempting
to roam via an explicitly request to a specific BSS so that we don't
initiate another connection attempt based on the possibly received scan
results from a scan that was in progress at the time the roam command
was received.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Don't use 'protected' as the name of the variable in bss.h since this
might be used in control interfaces that use C++.
Fixes: 1c77f3d3f9 ("Indicate whether additional ANQP elements were protected")
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a more specific name for the control interface command used for
managing the list of BSSIDs that are temporarily ignored.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add PASN implementation to wpa_supplicant
1. Add functions to initialize and clear PASN data.
2. Add functions to construct PASN Authentication frames.
3. Add function to process PASN Authentication frame.
4. Add function to handle PASN frame TX status.
5. Implement the station side flow processing for PASN.
The implementation is missing support for wrapped data and PMKSA
establishment for base AKMs, and only supports PASN authentication or
base AKM with PMKSA caching.
The missing parts will be added in later patches.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
PASN requires to store the PTK derived during PASN authentication
so it can later be used for secure LTF etc. This is also true
for a PTK derived during regular connection.
Add an instance of a PTKSA cache for each wpa_supplicant
interface when PASN is enabled in build configuration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Add user configured vendor IEs for Probe Request frames to default scan
IEs so that these IEs will be included in the Probe Request frames for
the scans issued also by components other than wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support possible band combinations of 2.4 GHz, 5 GHz, and 6 GHz with
QCA_WLAN_VENDOR_ATTR_SETBAND_MASK attribute. Ensure backwards
compatibility with old drivers that are using
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE attribute and supporting only 2.4 GHz
and 5 GHz bands.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Store information on whether extra ANQP elements were received using the
protection alternative (protected GAS during an association using PMF)
and make this available through the control interface BSS command.
For example:
anqp[277]=<hexdump>
protected-anqp-info[277]=1
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This makes it easier to change the internal struct wpa_bss design for
storing the variable length IE buffers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This removes need from the callers to know the struct wpa_bss details
for the location of the memory area for storing the IEs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The newer kernel versions enforce strict netlink attribute policy
validation and will cause cfg80211 to reject vendor commands with
NL80211_ATTR_VENDOR_DATA if NLA_F_NESTED attribute is not set but
if the vendor command is expecting nested data within
NL80211_ATTR_VENDOR_DATA attribute.
Most of the earlier instances were addressed by adding NLA_F_NESTED
flag in nla_nest_start(). This commit addresses the remaining
instance in which NL80211_ATTR_VENDOR_DATA is populated using data
set by user through the control interface.
Enhance the control interface VENDOR command to indicate whether the
vendor subcommand uses nested attributes within NL80211_ATTR_VENDOR_DATA
attribute or not.
Set NLA_F_NESTED flag for existing QCA vendor commands which use nested
attributes within the NL80211_ATTR_VENDOR_DATA attributes so that the
old frameworks implementations for already existing commands work
without any issues.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The D-Bus implementation of RemoveAllNetworks differs wildly from the
CLI implementation. Let's share the implementations.
This resolves use-after-free bugs I noticed, where we continue to use
the 'wpa_s->current_ssid' wpa_ssid object after freeing it, because we
didn't bother to disconnect from (and set to NULL) current_ssid before
freeing it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Within wpas_connection_failed(), the 'count' value of wpa_blacklist is
erroneously used as a tally of the number times the device has failed
to associate to a given BSSID without making a successful connection.
This is not accurate because there are a variety of ways a BSS can be
added to the blacklist beyond failed association such as interference
or deauthentication. This 'count' is lost whenever the blacklist is
cleared, so the wpa_supplicant stores an additional value
'extra_blacklist_count' which helps persist the 'count' through clears.
These count values are used to determine how long to wait to rescan
after a failed connection attempt.
While this logic was already slightly wrong, it would have been
completely broken by the upcoming change which adds time-based
blacklisting functionality. With the upcoming change, 'count' values
are not cleared on association, and thus do not necessarily even
approximate the "consecutive connection failures" which they were being
used for.
This change seeks to remove this unnecessary overloading of the
blacklist 'count' by directly tracking consecutive connection failures
within the wpa_supplicant struct, independent of the blacklist. This new
'consecutive_conn_failures' is iterated with every connection failure
and cleared when any successful connection is made. This change also
removes the now unused 'extra_blacklist_count' value.
Signed-off-by: Kevin Lund <kglund@google.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Teach wpa_supplicant to {de,}initialize bgscans when bgscan parameters
are set after initial connection.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Currently, wpa_config_set(), the function that sets wpa_supplicant
per-network properties, returns 1 when a property it attempts to set is
unchanged. Its global parallel, wpa_config_process_global(), doesn't do
this even though much of the code is very similar. Change this, and
several of the parser functions, to resemble the per-network parser and
setter functions.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Previously, wpa_supplicant fetched BSS channel info from scan results to
send ANQP Query frames. If the scan results for the specified BSS are
not available, the ANQP_GET command request was getting rejected.
Add support to send ANQP Query frame on the specified frequency without
requiring the scan results to be available.
The control interface command format:
- ANQP_GET <dst_addr> [freq=<freq in MHz>] <Query ID1>[,<Query ID2>,..]
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add an optional iter=# parameter to DPP_RECONFIG similarly to the way
this was handled with DPP_CHIRP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add override parameters to use the specified channel while populating
OCI element in EAPOL-Key group msg 2/2, FT reassoc request, FILS assoc
request and WNM sleep request frames.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Add support for missing driver AKM capability flags from the list of
RSN_AUTH_KEY_MGMT_* flags and make these available through the
'GET_CAPABILITY key_mgmt' control interface command.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
To support the STA testbed role, the STA has to use specified channel
information in OCI element sent to the AP in EAPOL-Key msg 2/4, SA Query
Request, and SA Query Response frames. Add override parameters to use
the specified channel while populating OCI element in all these frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to query per interface type AKM capabilities through the
control interface. For example, "GET_CAPABILITY key_mgmt
iftype=STATION".
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Extend DPP chirping mechanism to allow Reconfig Announcement frames to
be transmitted instead of the Presence Announcement frames. Add a new
wpa_supplicant control interface command "DPP_RECONFIG <network id>" to
initiate reconfiguration for a specific network profile.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"SET dpp_version_override <ver>" can now be used to request
wpa_supplicant and hostapd to support a subset of DPP versions. In
practice, the only valid case for now is to fall back from DPP version 2
support to version 1 in builds that include CONFIG_DPP2=y.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Increase the maximum command length from 4 kB to 8 kB mainly to allow
larger certificate blobs to be configured. Use heap memory to avoid
inconveniently large stack requirements. In addition, reject potentially
truncated commands instead of trying to process them.
The maximum length of the request can now be determined with
"GET max_command_len".
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a build flag CONFIG_NO_TKIP=y to remove all TKIP functionality from
hostapd and wpa_supplicant builds. This disables use of TKIP as both the
pairwise and group cipher. The end result does not interoperate with a
WPA(v1)-only device or WPA+WPA2 mixed modes.
Signed-off-by: Disha Das <dishad@codeaurora.org>
Allow wpa_supplicant to be requested to override the RSNXE Used subfield
in FT reassociation case for testing purposes with "SET ft_rsnxe_used
<0/1/2>" where 0 = no override, 1 = override to 1, and 2 = override to
0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new wpa_supplicant network profile parameter dpp_pfs can be used to
specify how PFS is applied to associations. The default behavior
(dpp_pfs=0) remains same as it was previously, i.e., try to use PFS if
the AP supports it. PFS use can now be required (dpp_pfs=1) or disabled
(dpp_pfs=2).
This is also working around an interoperability issue of DPP R2 STA with
certain hostapd builds that included both OWE and DPP functionality.
That issue was introduced by commit 09368515d1 ("OWE: Process
Diffie-Hellman Parameter element in AP mode") and removed by commit
16a4e931f0 ("OWE: Allow Diffie-Hellman Parameter element to be
included with DPP"). hostapd builds between those two commits would
reject DPP association attempt with PFS. The new wpa_supplicant default
(dpp_pfs=0) behavior is to automatically try to connect again with PFS
disabled if that happens.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wpa_supplicant control interface command "DPP_CHIRP own=<BI
ID> iter=<count>" to request chirping, i.e., sending of Presence
Announcement frames, to be started.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"DPP_BOOTSTRAP_SET <ID> <configurator parameters..>" can now be used to
set peer specific configurator parameters which will override any global
parameters from dpp_configurator_params.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"GET last_tk_key_idx" can now be used in testing build to determine
which was the last configured Key ID for the pairwise key.
Signed-off-by: Jouni Malinen <j@w1.fi>
Support Extended Key ID in wpa_supplicant according to
IEEE Std 802.11-2016 for infrastructure (AP) associations.
Extended Key ID allows to rekey pairwise keys without the otherwise
unavoidable MPDU losses on a busy link. The standard is fully backward
compatible, allowing STAs to also connect to APs not supporting it.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
The new wpa_supplicant control interface SET parameter disable_sa_query
can now be used to disable SA Query on receiving unprotected
disconnection event.
Signed-off-by: Jouni Malinen <j@w1.fi>
