This new parameter allows hostapd to add Vendor Specific elements into
(Re)Association Response frames similarly to the way vendor_elements
parameter can be used for Beacon and Probe Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If a legacy client with no P2P PS support is trying to connect to
a P2P GO, the driver should know that, and change its PS behavior
accordingly.
Add a parameter to hostapd_sta_add_params() indicating if P2P PS is
supported by the station and pass this parameter to kernel with nl80211
driver when the station is added/set.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
This removes multiple copies of wpabuf_resize() following by
wpabuf_put_{buf,data}() with the help of two simple helper functions.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add MBO IE with AP capability attribute to Beacon, Probe Response, and
(Re)Association Response frames to indicate the AP supports MBO.
Add option to add Association Disallowed attribute to Beacon, Probe
Response, and (Re)Association Response frames. Usage:
SET mbo_assoc_disallow <reason code>
Valid reason code values are between 1-5. Setting the reason code to
0 will remove the Association Disallowed attribute from the MBO IE
and will allow new associations.
MBO functionality is enabled by setting "mbo=1" in the config file.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add support for drivers that support full AP client state, i.e., can
handle adding stations that are not associated yet. For such drivers,
add a station after processing the authentication request, instead of
adding it in the association response callback.
Doing so is beneficial in cases where the driver cannot handle the add
station request, in which case it is useless to perform the complete
connection establishment.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.
In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.
Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When ACS is offloaded to device driver and the hw_mode parameter is set
to any, the current_mode structure is NULL which fails the ACS command.
Fix this by populating the ACS channel list with channels from all bands
when current_mode is NULL.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds the FST IEs received from the FST module into Beacon, Probe
Response, and (Re)Association Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Commit 95b6bca66d ('Add rsn_pairwise bits
to set_ieee8021x() driver_ops') modified cipher configuration to use
unconditionally wpa_pairwise | rsn_pairwise. While that works for many
cases, it does not handle the case of dynamic configuration changes over
the control interface where wpa_pairwise or rsn_pairwise values may not
get cleared when the wpa parameter is modified. Fix this inconsistency
by configuring the driver with only the bits that are valid for the
currently enabled WPA/WPA2 version(s).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update ACS driver offload feature for VHT configuration. In addition,
this allows the chanlist parameter to be used to specify which channels
are included as options for the offloaded ACS case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 16689c7cfc ('hostapd: Allow ACS to
be offloaded to the driver') used incorrect operator to determine
whether HT40 was configured. Fix that to mask the ht_capab bit
correctly. (CID 77286)
Signed-off-by: Jouni Malinen <j@w1.fi>
Using QCA vendor command, allow ACS function to be offloaded to the
driver. Once channels are selected, hostapd is notified to perform OBSS
operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 7f0303d5b0 ('hostapd: Verify VHT
160/80+80 MHz driver support') added couple of hapd->iface->current_mode
dereferences of which the one in hostapd_set_freq() can be hit with some
configuration files when using driver wrappers that do not have hw_mode
data, i.e., when current_mode is NULL. This could result in segmentation
fault when trying to use driver=wired. Fix this by checking that
current_mode is not NULL before dereferencing it to get vht_capab.
Signed-off-by: Jouni Malinen <j@w1.fi>
This fixes an issue where a driver using the deprecated set_ieee8021x()
callback did not include rsn_pairwise bits in the driver configuration
even if mixed WPA+WPA2 configuration was used. This could result, e.g.,
in CCMP not being enabled properly when wpa_pairwise=TKIP and
rsn_pairwise=CCMP was used in the configuration. Fix this by using
bitwise OR of the wpa_pairwise and rsn_pairwise values to allow the
driver to enable all pairwise ciphers.
In addition, make the newer set_ap() driver_ops use the same bitwise OR
design instead of picking between rsn_pairwise and wpa_pairwise. This
makes the code paths consistent and can also fix issues with mixed mode
configuration with set_ap().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There is not much point in building devices with WPS 1.0 only supported
nowadays. As such, there is not sufficient justification for maintaining
extra complexity for the CONFIG_WPS2 build option either. Remove this by
enabling WSC 2.0 support unconditionally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The 802.11ac amendment specifies that that the center segment 0 field
is reserved, so it should be zero. Hostapd previously required it to
be set, which is likely a good idea for interoperability, but allow it
to be unset. However, don't allow it to be set to a random value, only
allow zero and the correct channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, we printed this message as a debug one, which was confusing
in case verbose debug messages were disabled. User could think CAC
started but never ended. Add more parameterss to DFS_EVENT_CAC_START, so
external programs can more easily check what was wrong in case of
errors.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
hostapd_drv_wnm_oper() needs to indicate an error if the driver callback
function is not implemented. Without this, the buf_len argument could
have been left uninitialized which could result in crashing the process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This allows use of structs (and not only pointers) defined in drivers.h.
Remove also some not needed forward declarations and redundant includes.
Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
hostapd_set_freq_param() rejected the 20 MHz channel case with
vht_enabled due to the existing validation step including only 5 GHz (to
be more exact, only >= 5000 MHz). While the behavior may not be fully
defined for 2.4 GHz, we can enable this based on driver capability
advertisement to fix automatic VHT selection for P2P use cases.
mac80211_hwsim advertises VHT for 2.4 GHz band and that resulted in
failures when trying to start GO on that band with vht=1 parameter.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
DFS operations are specific to the interface (radio/wiphy), not BSS
(netdev/vif), so hostapd_iface is the appropriate element to use in
them.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, ENABLE command ended up freeing the hostapd_iface context on
initialization failures, but did not even remove the interface from the
list of available interfaces. This resulted in use of freed memory with
any following operation on the same interface. In addition, removing the
interface on initialization failure does not seem like the best
approach. Fix both of these issues by leaving the interface instance in
memory, but in disabled state so that the configuration can be fixed and
ENABLE used again to enable the interface or REMOVE used to remove the
interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Make sure the driver supports 160/80+80 MHz VHT capabilities
before trying to configure these channels.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
When we have CAC active and receive a radar event, we should ignore
CAC_ABORT event and handle channel switch in the radar event handler.
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
This allows QoS Map Set element to be added to (Re)Association Response
frames and in QoS Map Configure frame. The QoS Mapping parameters are
also made available for the driver interface.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add DFS structures/events handlers, CAC handling, and radar detection.
By default, after radar is detected or the channel became unavailable, a
random channel will be chosen.
This patches are based on the original work by Boris Presman and
Victor Goldenshtein. Most of the DFS code is moved to a new dfs.c/dfs.h
files.
Cc: Boris Presman <boris.presman@ti.com>
Cc: Victor Goldenshtein <victorg@ti.com>
Signed-hostap: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
The static WEP keys have to be configured for the new VLAN
interface that is created for a 4addr WDS peer, not doing so
breaks WEP functionality in nl80211/4addr based WDS links.
Signed-hostap: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Commit b52f084cfa introduced a mechanism
for adding arbitrary vendor-specific elements into the Beacon and Probe
Response frames. However, this information was not added to the separate
buffers used for specifying Beacon and Probe Response IEs for drivers
that build the frames internally. Add vendor_elements to these values,
too, to support such drivers in addition to drivers that use the full
Beacon tail/head buffers.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This commit adds control interface commands and internal storage of
Wi-Fi Display related configuration. In addition, WFD IE is now added
to various P2P frames, Probe Request/Response, and (Re)Association
Request/Response frames. WFD subelements from peers are stored in the
P2P peer table.
Following control interface commands are now available:
SET wifi_display <0/1>
GET wifi_display
WFD_SUBELEM_SET <subelem> [hexdump of length+body]
WFD_SUBELEM_GET <subelem>
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This updates a previous patch did more or less the same thing by
providing the qosinfo as a single variable to the driver wrappers.
Signed-hostap: Jason Young <jason.young@dspg.com>
Add uapsd_queues and max_sp fields to sta_info struct,
and pass them to the sta_add callback.
These values are determined by the WMM IE in the (Re)Association Request.
Signed-off-by: Eliad Peller <eliad@wizery.com>
