Specify the secondary channel offset and correct center_freq1 value to
make the parameters complete for a 40 MHz channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
Include a defconfig for building kernel as UML. Also update the README
with a few notes related to UML.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Make the included kernel-config a little more minimal by checking in the
defconfig instead.
Generate the defconfig by checking out a linux at tag wt-2020-03-17,
copy kernel-config to .config, run
'yes "" | make oldconfig && make savedefconfig',
and copy resulting defconfig to kernel-config.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
If we use user-mode-linux, we have time-travel, and then the --long
argument doesn't really make a difference, so just assume that's the
case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
bgscan_learn_beacon_loss was failing quite frequently and it looks like
the background scans were related to those failures. Since those scans
are not really relevant to testing beacon loss, get rid of them in these
test cases to avoid incorrect failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previously used normal data TX depends on undefined driver behavior
after all keys have been removed. That may not be available, so do this
more properly with frame injection through a monitor interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Stopping the AP from beaconing will also stop it from acknowledging
frames and that resulted in bgscan_learn_beacon_loss failing when
mac80211_hwsim is registering REPORTS_TX_ACK_STATUS. Work around this by
moving to using PMF so that the station ignores the unprotected
deauthentiation frames from the AP and also disabling SA Query. This
allows the AP to be stopped and restarted with large enough Beacon
interval to allow the station to detect beacon loss.
This is identical to the earlier design change for
bgscan_simple_beacon_loss (somehow this bgscan_learn_beacon_loss test
case managed to pass at that time).
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks ike the authentication timeouts may continue a bit longer after
some kernel changes and that could result in temporarily disabling the
network profile. Give this test case more time to complete the
connection to avoid reporting failures unnecessarily.
Signed-off-by: Jouni Malinen <j@w1.fi>
Stopping the AP from beaconing will also stop it from acknowledging
frames and that resulted in bgscan_simple_beacon_loss failing when
mac80211_hwsim is registering REPORTS_TX_ACK_STATUS. Work around this by
moving to using PMF so that the station ignores the unprotected
deauthentiation frames from the AP and also disabling SA Query. This
allows the AP to be stopped and restarted with large enough Beacon
interval to allow the station to detect beacon loss.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like this test case can fail if the STA goes to power save mode
and the Deauthentication frame from the AP after session timeout is not
actually sent at all. Check more details to make it clear that this is
indeed the reason behind the failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set device_name in the test cases instead of relying on the
wpa_supplicant configuration file. This fixes problems when we run WPS
test cases in remote test environment.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Leaving out the special sae_pwe value was causing failures for following
test cases, e.g., in the following sequence:
sigma_dut_sae_pw_id_pwe_loop sae_password_id_only
Signed-off-by: Jouni Malinen <j@w1.fi>
Some test case sequences seemed to prevent the station from completing
the first OBSS scan (that scan was aborted) and that resulted in failing
the test case because the AP had not received any report in time. Wait
for scan completion and allow additional scans before timing out to
avoid indicating incorrect AP behavior in cases where the report was not
even received.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
WEP should not be used for anything anymore. As a step towards removing
it completely, move all WEP related functionality to be within
CONFIG_WEP blocks. This will be included in builds only if CONFIG_WEP=y
is explicitly set in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
