Commit graph

344 commits

Author SHA1 Message Date
Jouni Malinen
8c9ad085e9 P2P: Relax Bonjour SD query matching
The DNS Name is allowed to use or not use domain name compression. To
handle both cases, check human readable DNS Name match if binary
matching does not show a hit.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-31 18:25:30 +02:00
Jouni Malinen
560f8bda8c P2P: Support multiple P2P SD Bonjour services with same key
There may be multiple Bonjour PTR matches for the same key, so extend
the P2P SD code for this to allow such entries to be added (i.e., do not
override previously added value, but add a new one). Similarly, return
multiple matches (one per Service TLV) for a query if it happens to
match more than a single configured Bonjour service.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-31 13:01:43 +02:00
Jouni Malinen
96beff11d1 P2P: Allow discoverable interval for p2p_find to be configured
The new P2P_SET parameter disc_int can now be used to configure
discoverable interval for p2p_find operations. The format of the command
for setting the values is "P2P_SET disc_int <minDiscoverableInterval>
<maxDiscoverableInterval> <max TUs for discoverable interval>". The
first two parameters are given in units of 100 TUs (102.4 ms). The third
parameter can be used to further limit the interval into a specific TU
amount. If it is set to -1, no such additional limitation is enforced.
It should be noted that the P2P specification describes the random
Listen state interval to be in units of 100 TUs, so setting the max TU
value to anything else than -1 is not compliant with the specification
and should not be used in normal cases. The default parameters can be
set with "P2P_SET disc_int 1 3 -1".

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-30 15:12:04 +02:00
Jouni Malinen
340f1c48f7 P2P: Clear pending_pd_before_join on PD timeout
wpas_p2p_pd_before_join_timeout() needs to clear the
pending_pd_before_join flag to match other uses of this flag prior to
calling wpas_p2p_join_start(). Without this, the flag could be left set
which can cause following P2P operations to behave in unexpected ways.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-29 16:25:02 +02:00
Jouni Malinen
d76cd41a3a P2P: Allow separate P2P group interface use to be disabled
The new p2p_no_group_iface=1 configuration parameter can now be used to
disable the default behavior of adding a separate interface for the P2P
group when driver support for concurrent interfaces is available.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-29 15:02:30 +02:00
Jouni Malinen
5fbddfdcf1 P2P: Fix default p2p_group_idle timeout for P2P client role
Commit 0d30cc240f forced
wpa_s->current_ssid to be cleared in wpa_supplicant_mark_disassoc()
which gets called from wpa_supplicant_event_disassoc(). This breaks the
P2P group idle mechanism for the case where p2p_group_idle is not set
(i.e., is the default 0) since wpas_p2p_group_idle_timeout() ignores the
timeout in that case if the interface is not recognized as a client
interface (which was based on wpa_s->current_ssid being set).

Fix this by making wpas_p2p_is_client() default to client case if
wpa_s->current_ssid is NULL. This is much more likely case since the P2P
GO mode operation would not really clear the pointer without explicit
request to disconnect.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-10-28 21:37:15 +02:00
Jouni Malinen
04a3e69dd1 P2P: Allow all channels with multi-channel concurrency
If the driver indicates support for multi-channel concurrency, change
the p2p_connect behavior to not force the current operating channel, but
instead, just mark it as preferred for GO Negotiation. This change
applies only for the case when the freq parameter is not used with the
p2p_connect command.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-26 18:10:46 +03:00
Jouni Malinen
13ece96f70 P2P: Improve robustness against lost ctrl::ack frames
P2P includes two use cases where one of the devices is going to start a
group and likely change channels immediately after processing a frame.
This operation may be fast enough to make the device leave the current
channel before the peer has completed layer 2 retransmission of the
frame in case the ctrl::ack frame was lost. This can result in the peer
not getting TX status success notification.

For GO Negotiation Confirm frame, p2p_go_neg_conf_cb() has a workaround
that ignores the TX status failure and will continue with the group
formation with the assumption that the peer actually received the frame
even though we did not receive ctrl::ack. For Invitation Response frame
to re-invoke a persistent group, no such workaround is used in
p2p_invitation_resp_cb(). Consequently, TX status failure due to lost
ctrl::ack frame results in one of the peers not starting the group.

Increase the likelihood of layer 2 retransmission getting acknowledged
and ctrl::ack being received by waiting a short duration after having
processed the GO Negotiation Confirm and Invitation Response frames for
the re-invocation case. For the former, use 20 ms wait since this case
has been worked around in deployed devices. For the latter, use 50 ms
wait to get even higher likelihood of getting ctrl::ack through since
deployed devices (and the current wpa_supplicant implementation) do not
have a workaround to ignore TX status failure.

20 ms is long enough to include at least couple of retries and that
should increase likelihood of getting ctrl::ack through quite a bit. The
longer 50 ms wait is likely to include full set of layer 2 retries.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-13 17:33:16 +03:00
Jouni Malinen
c423708f02 WPS: Allow PIN timeout to be specified with wpa_supplicant AP/GO
Extend the wpa_cli wps_pin command to support specification of the PIN
expiration time in seconds similarly to hostapd_cli wps_pin command when
using wpa_supplicant for AP mode (including P2P GO).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-10 17:22:35 +03:00
Jouni Malinen
6d22a377bd P2P: Fix network removal on P2P connect to select correct block
If wpa_s->current_ssid is not set (e.g., after disconnection that
did not result in immediate group removal), an incorrect group could
have been removed since the network block iteration here could select
the network block that is used to store persistent group credentials.
Fix this by verifying that disabled != 2 to avoid picking the network
block that could not have been the temporary P2P group.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-10-05 20:37:49 +03:00
Jouni Malinen
30b8038921 P2P: Fix p2p_cancel processing during group formation
The wpa_s->p2p_in_provisioning flag did not get cleared in some cases
where p2p_cancel command is used to stop group formation. This can result
in some operations (like p2p_find) failing afterwards. Fix this by using
wpas_group_formation_completed() when processing p2p_cancel for a group
that has not yet completed group formation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-09-28 22:01:48 +03:00
Jouni Malinen
83218d20dd P2P: Clear sta_scan_pending on group removal
It is possible for the P2P client group to be removed while waiting for
a pending scan operation (e.g., when p2p_group_idle timeout hits after
getting disconnected from the GO with something else than
Deauthentication with reason code 3). If this happens with a P2P
interface that is used both for P2P Device and group roles, scan state
could get stuck while waiting for the next scan to complete since no
more station (P2P client) mode scans are scheduled. Fix this by clearing
sta_scan_pending when removing the temporary group network block.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-09-25 02:55:20 +03:00
Jouni Malinen
2cd0758441 P2P: Allow peer to propose channel in invitation process
Make Invitation process for re-invoking a persistent group behave
similarly to GO Negotiation as far as channel negotiation is concerned.
The Operating Channel value (if present) is used as a starting point if
the local device does not have a forced operating channel (e.g., due to
concurrent use). Channel lists from devices are then compared to check
that the selected channel is in the intersection. If not, channel is
selected based on GO Negotiation channel rules (best channel preferences
etc.). Invitation Request is rejected if no common channel can be
selected.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-09-24 22:15:58 +03:00
Jouni Malinen
ac06fb12f5 P2P: Add more debug prints for GO start routines
This makes it easier to debug issues in starting GO mode.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-24 01:05:51 +03:00
Jouni Malinen
c244dd2ec0 P2P: Fix PSK configuration for GO network
Setting just ssid->passphrase is not enough to complete the network
block for the GO entry. Also the PSK needs to be derived so that the
network is considered enabled by wpas_network_disabled(). The previous
version worked as long as something else allowed the scan request to be
performed (this is needed even though the actual scan is skipped when
starting GO).

The first GO start was allowed because wpa_s->scan_req is initialized to
1 in wpa_supplicant_alloc(). However, other attempts may fail if
wpa_s->scan_req is cleared. This failure shows up as "No enabled
networkas - do not scan" in debug log followed by state change to
INACTIVE when trying to start GO.

Fix this by deriving PSK from the passphrase for GO mode.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-24 00:56:57 +03:00
Jouni Malinen
0c802384a7 P2P: Fix p2p_group_idle in no-group-interface P2P client case
Commit 30ee769235 started skipping P2P
group removal if wpa_s->current_ssid is not set and commit
0d30cc240f started clearing
wpa_s->current_ssid on disconnection. This combination broke
p2p_group_idle timeout on P2P client interface in a case where no
separate P2P group interface is used and when the disconnection is
triggered by something else than an explicit indication of GO
terminating the group.

Fix this by relaxing network block matching rules when figuring out
whether any of the configured network blocks could be in P2P use. The
p2p_group flag alone should be enough for this since temporary P2P group
network blocks are removed once the P2P group is terminated.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-23 20:28:03 +03:00
Mykyta Iziumtsev
dd31eb79a2 P2P: Remove channel 14 from supported P2P channels
Channel 14 is available only in Japan and is DSSS-only according to
IEEE 802.11-2012 19.4.3 and MIC Equipment Ordinance (EO)
for Regulating Radio Equipment article 49.20.

At the same time, P2P should avoid using DSSS modulation in normal
operation according to P2P specification v1.2 2.4.1.

Signed-hostap: Mykyta Iziumtsev <mykyta.iziumtsev@gmail.com>
intended-for: hostap-1
2012-09-23 12:49:52 +03:00
Jouni Malinen
58d3760e7e P2P: Check all interfaces for pending scan for p2p_scan failures
Driver could reject the new scan based on any virtual interface
running a concurrent scan. As such, mark the pending scan callback
for P2P based on any interfaces instead of just the one used for
the p2p_scan operation.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-13 18:03:14 -07:00
Jouni Malinen
e665ca9a8d P2P: Move p2p_cb_on_scan_complete to global context
Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-13 17:58:22 -07:00
Jouni Malinen
0aadd5682f Fix disconnection event processing
Commit 0d30cc240f forced
wpa_s->current_ssid and wpa_s->key_mgmt to be cleared in
wpa_supplicant_mark_disassoc() which gets called from
wpa_supplicant_event_disassoc(). This broke IEEE 802.1X authentication
failure processing and P2P deauthentication notification (group
termination).

Fix this by splitting wpa_supplicant_event_disassoc() into two parts and
make wpas_p2p_deauth_notif() indicate whether the interface was removed.
If so, the last part of disassocition event processing is skipped. Since
the wpa_supplicant_mark_disassoc() call is in the second part, the above
mentioned issues are resolved. In addition, this cleans up the P2P group
interface removal case by not trying to use fast reconnection mechanism
just before the interface gets removed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-31 22:04:41 +03:00
Jouni Malinen
6f1ca696c7 P2P: Do not fail p2p_group_remove just based on current_ssid
The wpa_s->current_ssid pointer may get cleared, e.g., when
disconnected. Commit 30ee769235 made
wpas_p2p_group_delete() exit early before removing a P2P interface in
this type of case. That can cause number of issues from p2p_group_remove
command failing to busy loop when terminating wpa_supplicant if there is
a P2P group interface in client mode and that interface happens to be in
disconnected state. Fix these issues by allowing wpas_p2p_group_delete()
remove the P2P group interface regardless of whether wpa_s->currnt_ssid
is set.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-31 21:35:32 +03:00
Jouni Malinen
4d32c0c44d P2P: Allow p2p_invite-persistent to specify channel for GO
The freq and ht40 parameters can now be used with the p2p_invite
command when reinvoking a persistent group as the GO.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-31 21:20:51 +03:00
Jouni Malinen
6ffdc2f7bd WFD: Add preliminary WSD request processing and response
This commit does not yet address support for different device roles,
i.e., the same set of subelements are returned regardless of which
role was indicated in the request.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-29 19:51:29 +03:00
Jouni Malinen
347d6a5b76 WFD: Add support for sending Wi-Fi Display service discovery requests
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.

format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-29 19:51:29 +03:00
Jouni Malinen
bf428a739c P2P: Fix memory leak with driver-based P2P management
If the P2P management operations are handled within the driver, the
P2P service entries were not freed when terminating wpa_supplicant.
Fix this by calling wpas_p2p_service_flush() even if the P2P module
within wpa_supplicant has not been initialized.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-24 20:45:22 +03:00
Jouni Malinen
b4a5dfa95d P2P: Limit maximum number of stored P2P clients to 100
This limits the maximum size of the p2p_client_list parameter that
is maintained at the GO for a persistent group. In other words, only
the 100 most recently seen P2P clients are kept in the list.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-08-24 00:25:14 +03:00
Jouni Malinen
223167956c Improve p2p_client_list updates in configuration file
This list can get truncated due to too many addresses getting added.
Reorder the entries in a way that allows the most recently added values
to be maintained in the list and use better debug/error messages when
parsing the value.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-08-24 00:25:14 +03:00
Jouni Malinen
99fcd40409 P2P: Allow scan operations during p2p_find
Previously, all station mode scan operations were either skipped or
delayed while any P2P operation was in progress. To make concurrent
operations easier to use, reduce this limitation by allowing a scan
operation to be completed in the middle of a p2p_find. In addition,
allow station mode association to be completed. When the station mode
operation is run to its completion (scan results not acted on,
connection to an AP completed, connection failed), resume the p2p_find
operation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 19:42:53 +03:00
Jouni Malinen
05a77b3b46 P2P: Use 500 ms search delay by default during concurrent operations
If the p2p_find command is used without the delay parameter, a 500 ms
default search delay will now be used when any interface using the same
radio is in an concurrent operation. "p2p_find delay=0" can be used to
enforce the old behavior in such a case if needed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 18:34:57 +03:00
Jouni Malinen
37448ede31 P2P: Add option for adding extra delay to p2p_find
A new optional delay=<search delay in milliseconds> parameter can now be
used with p2p_find command to request an extra delay between search
iterations. This can be used, e.g., to make p2p_find friendlier to
concurrent operations by avoiding it from taking 100% of the radio
resources.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-23 18:20:58 +03:00
Jouni Malinen
4f219667d7 P2P: Use larger GO config timeout if HT40 is used
Increase GO config timeout if HT40 is used since it takes some time
to scan channels for coex purposes before the BSS can be started.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-15 23:19:11 +03:00
Rajkumar Manoharan
e2308e4b45 P2P: Add optional "ht40" argument for p2p_connect
This can be used to start negotiated GO in 40 MHz channel width
in 5GHz band.

Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2012-08-15 23:07:44 +03:00
Rajkumar Manoharan
7aeac98509 P2P: Enable 40 MHz support for autonomous P2P group addition
Add optional "ht40" argument for p2p_group_add command to enable 40 MHz
in 5GHz band. This configures the secondary channel, when HT support is
enabled and if the HW supports 40 MHz channel width.

Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2012-08-15 22:53:01 +03:00
Rajkumar Manoharan
931228aa10 P2P: Move channel validation into a separate function
Signed-hostap: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2012-08-15 22:44:34 +03:00
Jouni Malinen
067ffa2696 Convert os_realloc() for an array to use os_realloc_array()
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-13 21:21:23 +03:00
Jouni Malinen
8dba4aef11 P2P: Move group removal reason to a function parameter
wpa_s->removal_reason was set only when calling wpas_p2p_group_delete()
and while couple of call places did not set this, it should really be
set in each case. As such, it works better as a function parameter than
a variable in struct wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-11 12:41:31 +03:00
Michael Naumov
30ee769235 P2P: p2p_group_remove should fail on non-P2P interface
p2p_group_remove should only attempt to remove P2P group
interfaces and fail on non-P2P group interfaces.

Signed-hostap: Michael Naumov <michael.naumov@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
2012-08-11 12:06:23 +03:00
Eyal Shapira
462a7439e1 Add p2p_go_max_inactivity config option
This enables setting a different max inactivity timeout for P2P GO.
This timeout is used to detect inactive clients. In some scenarios
it may be useful to have control over this and set a shorter timeout
than the default 300s. For example when running STA and P2P GO interfaces
concurrently, the STA interface may perform scans which may cause the
GO to miss a disassoc / deauth frames from a client and keep assuming
that the client is connected until the inactivity detection kicks in.
300 secs is a bit too long for such scenarios and creates a bad user
experience.

Signed-hostap: Eyal Shapira <eyal@wizery.com>
2012-08-10 16:28:38 +03:00
Jouni Malinen
3df2f4fe99 P2P: Remove unused P2P_SCAN_SPECIFIC
This is not used anymore after the commit
e6ecfc4fd3.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-30 20:20:29 +03:00
Sunil Dutt Undekari
5bda43cdee P2P: Reject p2p_find when in provisioning
A p2p_find during provisioning shall not allow the enrollee to
pick the network, hence disable p2p_find during provisioning.

Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
2012-06-25 14:05:49 +03:00
Aarthi Thiruvengadam
c66cf68d5c P2P: Fix fallback to GO Negotiation to avoid PD-before-join timeout
The wpas_p2p_pd_before_join_timeout could be left behind if the PD
Request in p2p_connect-auto case does not succeed. This timeout can
result in unexpected operations since it could trigger join operation
while going through GO Negotiation. Fix this by canceling the timeout
when falling back to GO Negotiation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-06-20 21:38:31 +03:00
Jouni Malinen
73ccd08378 P2P: Fix group formation timeout on GO during WPS step
Commit 361cdf3400 changed the way the
group formation timeout is used on P2P client. However, it resulted in
clearing the timeout on the GO when the GO started beaconing. This is
not correct since the timeout is supposed to be maintained until at
least the completion of the WPS provisioning step. Fix this regression
by clearing the timeout here only in the case we are not GO in group
formation phase.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-06-08 18:22:03 +03:00
Jouni Malinen
5b37633364 P2P: Fix scan_res_handler setting for p2p_scan
The previous version set scan_res_handler unconditionally and then
cleared it if scan request failed. This can result in incorrect clearing
of the handler to NULL for a previously started scan that has not yet
completed. This can make p2p_find command fail to use the
start-after-scan-completion mechanism in some cases. Fix this by setting
scan_res_handler properly after having verified that the driver command
for starting the scan was successful.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-06-06 17:07:46 +03:00
Sunil Dutt Undekari
84286a227b P2P: Improve p2p_prov_disc-auto robustness
Perform addition additional scan runs on the operating channel of the GO
(if known from previous scan results) and fall back to initiate the PD
for GO Negotiation if these additional scans do not detect the peer as
GO.

Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
2012-06-06 15:46:05 +03:00
Nirav Shah
ad85320234 P2P: Fix P2P Group Formation timeout registration (use parent iface)
Commit 361cdf3400 extended the use of
group formation timeout for the way handshake, but the registration was
done on the group_interface while the cancellation was done on the
parent interface. Fix the registration to set the eloop timeout on
parent to address potential issues when using a separate group
interface.

Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
2012-06-04 21:58:34 +03:00
Jouni Malinen
b80eb89d8e P2P: Improve handling of p2p_connect-auto fallback
Commit aa9bb7644b improved robustness
of p2p_connect-auto mechanism by using older scan results to help in
determination whether the peer was operating a GO. Improve this by
accepting new GO information from scan-for-WPS-provisioning results
even if the GO is not yet ready for WPS.

In addition, fix an issue where Provision Discovery exchange timeout
could have left offchannel TX operation in progress when the fallback
was used.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-14 22:55:43 -04:00
Jouni Malinen
3bc462cb88 P2P: Add option for Provision Discovery before GO Negotiation
This is a workaround for interoperability issues with some deployed P2P
implementations that require a Provision Discovery exchange to be used
before GO Negotiation. The new provdisc parameter for the p2p_connect
command can be used to request this behavior without having to run a
separate p2p_prov_disc command.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-11 16:25:47 +03:00
Jouni Malinen
ab28911dbf P2P: Deinitialize global P2P context on P2P mgmt interface removal
The P2P implementation assumes that the first wpa_s interface instance
is used to manage P2P operations and the P2P module maintains a pointer
to this interface in msg_ctx. This can result in issues (e.g., use of
freed memory) when the management interface is removed. Fix this by
deinitializing global P2P data if the interface that created it is
removed. This will disable P2P until the next interface is added.

Signed-hostap: Jouni Malinen <j@w1.fi>
intended-for: hostap-1
2012-05-10 10:49:22 +03:00
Jouni Malinen
6f251b6bb5 P2P: Store SSID of the group in p2p_group data
This can be used with P2P management operations that need to verify
whether the local device is operating a specific group based on
P2P Group ID attribute from a peer.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 17:38:57 +03:00
Jouni Malinen
aa9bb7644b P2P: Allow older scan results to improve p2p_connect-auto robustness
Previusly the peer was assumed to not be operating a GO if the BSS entry
for it was not updated in the single scan run started by
p2p_connect-auto. This is not very robust since a scan may miss the peer
if either a Probe Request or Probe Response frame is lost. Improve
robustness by assuming the peer is still operating the GO and starting
the join operation. If the GO is not found during PD-for-join or the
single-channel scans during the join, fall back to GO Negotiation.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 17:38:57 +03:00
Wei-Jen Lin
1298c14594 Allow pbc_in_m1 workaround to be enabled in wpa_supplicant AP mode
This workaround for Windows 7 WPS probing mechanism was previously
allowed only with hostapd, but the same interoperability issue can
happen with wpa_supplicant AP/GO mode. Allow the workaround to be
enabled in wpa_supplicant configuration for these uses.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-03 16:51:04 +03:00
Wei-Jen Lin
f571b593ba P2P: Clone max_sta_num parameter for group interfaces
This is needed to allow the max_sta_num parameter set in the main
configuration file to apply to dynamically created P2P group
interfaces.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-05-03 16:41:15 +03:00
Jouni Malinen
23c84252a4 P2P: Add option to force SSID/passphrase for GO Negotiation
An existing persistent group information can now be used to force GO
Negotiation to use the previously used SSID/passphrase from a persistent
group if we become a GO. This can be used as an alternative to inviting
a new P2P peer to join the group (i.e., use GO Negotiation with GO
intent 15 instead of starting an autonomous GO and using invitation),
e.g., in case a GO Negotiation Request is received from a peer while we
are not running as a GO. The persistent group to use for parameters is
indicated with persistent=<network id> parameter to p2p_connect.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-27 18:25:30 +03:00
Jouni Malinen
0918c4bf3b P2P: Add p2p_prov_disc auto mechanism
wpa_supplicant can now be requested to automatically figure out whether
the indicated peer is operating as a GO and if so, use join-a-group
style PD instead of pre-GO Negotiation PD.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-26 17:13:03 +03:00
Jouni Malinen
25a94f525c P2P: Fix PD Failure event to show peer device address
The p2p_dev_addr parameter in the P2P-PROV-DISC-FAILURE event (added in
commit f65a239ba4) was supposed to the P2P
Device Address of the peer, not the local device.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-26 17:09:02 +03:00
Masashi Honma
78039295e6 P2P: Remove unused variable
The "type" variable is not used in wpas_p2p_deinit_global().
So this patch removes it.

Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
2012-04-21 18:21:30 +03:00
Deepthi Gowri
f65a239ba4 P2P: Add provision discovery failure event
Add provisional discovery failure ctrl_iface event
(P2P-PROV-DISC-FAILURE) to indicate to the application layer in case of
PD failure.

Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
2012-04-17 19:44:13 +03:00
Jouni Malinen
5f482d55fd P2P: Allow immediate group idle timeout configuration
A special value p2p_group_idle=-1 can now be used to configure the P2P
group idle mechanism to terminate a P2P client group immediately on any
disconnection after the completion of the initial 4-way handshake.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 17:03:27 +03:00
Jouni Malinen
361cdf3400 P2P: Extend use of group formation timeout until end of 4-way handshake
Instead of relying on the P2P group idle timeout before the group
connection has been fully established, re-start the group formation
timeout in the end of the WPS provisioning step and clear it at the
successful completion of the initial 4-way handshake. This allows the
P2P group idle timeout to be set to a small value without triggering it
during the initial scan and connection attempt.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 17:01:15 +03:00
Jouni Malinen
205e6474a1 P2P: Fix p2p_connect join scan handler in error cases
wpa_drv_scan() may fail for the initial p2p_connect join scan request,
e.g., if the driver happened to be scanning at the time the new
operation was initialized. Previously, a special scan result handler was
registered regardless of whether the new scan was started. This could
result in partial scan results (e.g., from p2p_find social scan) from
being used as full results for join (or now more importantly for
p2p_connect auto) purposes. Fix this by registering the new scan result
handler only if wpa_drv_scan() returns success.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 16:13:14 +03:00
Jouni Malinen
b31be3a0fd P2P: Add automatic GO Negotiation vs. join-a-group selection
p2p_connect command can now be used with an optional "auto" parameter
to request wpa_supplicant to determine automatically whether to use
join-a-group operation (if the peer is operating as a GO) or group
formation. This makes it easier for external programs to handle
connection type selection by offloading this to wpa_supplicant. The
previously used p2p_connect join commands can be replaced with
p2p_connect auto to use this new mechanism.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 16:04:36 +03:00
Jouni Malinen
86ae2e8a42 P2P: Fix shared freq check and support AP mode validation
The previous commit did not use the correct pointer in all operations
and was specific to station mode interfaces. Fix and extend it to work
with AP/GO interfaces, too.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-04-08 20:42:45 +03:00
Jouni Malinen
4b15620609 P2P: Abort join-group operation if concurrent group cannot be supported
If the driver does not indicate support for multi-channel concurrency,
abort join-group operation if the end result would result in use of
multiple operating frequencies with the same radio.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-04-08 20:12:05 +03:00
Nirav Shah
103b8f4dea P2P: Disconnect P2P group on supplicant deinit
When a supplicant is deinited and shutting, disconnect from P2P groups.
This fixes a memory leak on variable dbus_groupobj_path on exiting
supplicant.

Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
2012-04-06 18:41:06 +03:00
Angie Chinchilla
eb6f8c2bd4 P2P: Fix crash for failure case when WSC PIN is entered incorrectly
When forming a P2P group using WSC PIN method, if the PIN is entered
incorrectly the P2P client supplicant instance will crash as a result
of cleanup happening on data that is still in use in a case where a
separate P2P group interface is used.

For example, here is the path for the first crash:
eap_wsc_process():
- creates struct wpabuf tmpbuf; on the stack
- sets data->in_buf = &tmpbuf;
- calls wps_process_msg()
- which calls wps_process_wsc_msg()
- which, in case WPS_M4: calls wps_fail_event()
- which calls wps->event_cb()
- wps->event_cb = wpa_supplicant_wps_event()
- wpa_supplicant_wps_event()
- wpa_supplicant_wps_event_fail()
- which calls wpas_clear_wps()
- which calls wpas_notify_network_removed()
- which calls wpas_p2p_network_removed()
- which calls wpas_p2p_group_formation_timeout()
- which calls wpas_group_formation_completed()
- which calls wpas_p2p_group_delete()
- which calls wpa_supplicant_remove_iface()
- which calls wpa_supplicant_deinit_iface()
- which calls wpa_supplicant_cleanup()
- which calls eapol_sm_deinit()
- ... which eventually uses the ptr data->in_buf to free tmpbuf, our
stack variable and then the supplicant crashes

If you fix this crash, you'll hit another. Fix it and then a segfault.
The way we're cleaning up and deleting data from under ourselves here
just isn't safe, so make the teardown portion of this async.

Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
intended-for: hostap-1
2012-04-06 18:22:03 +03:00
Jouni Malinen
3fc14102f8 P2P: Remove client group on Deauthentication reason code 3
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-03 16:45:28 +03:00
Eliad Peller
3c29244eb7 P2P: Add deinit_p2p_cli op to clear P2P client driver state
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.

Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.

Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
2012-04-01 21:41:23 +03:00
Johannes Berg
2d43d37ff2 DBus: Add ability to report probe requests
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).

As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.

A small test script is also included.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 21:14:48 +03:00
Johannes Berg
baf513d695 Pass signal strength through, fix units
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.

Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.

My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 18:48:12 +03:00
Jouni Malinen
21d996f775 P2P: Add support for preferred channel list
p2p_pref_chan configuration parameter can now be used to set the
list of preferred channel for P2P GO Negotiation. This will be used
in the priority order if the peer does not support the channel we
are trying to use as the GO (configured operating channel or the
best 2.4 GHz/5 GHz channel) for the case where a forced channel is
not used.

p2p_pref_chan=<op class:channel>,...

For example:
p2p_pref_chan=81:1,81:2,81:3,81:4,81:5,81:6

This would configure 2.4 GHz channels 1-6 as the preferred ones with
channel 1 the most preferred option.

These configuration parameters can be set in wpa_supplicant.conf and
dynamically updated with "wpa_cli set <param> <value>".

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-29 21:28:34 +03:00
Jouni Malinen
8c472816fd P2P: Do not use group idle timeout during provisioning
Use the normal group formation timeout during the provisioning phase to
avoid terminating this process too early due to group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-27 18:04:06 +03:00
Jouni Malinen
f4329aa2d0 P2P: Validate p2p_oper_channel in p2p_group_add
If the p2p_group_add command does not specify the operating channel,
make sure the operating channel set in the configuration file meets
the P2P requirements in the same way as is done with the frequency
specified as the command parameter.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-26 22:06:48 +03:00
Jouni Malinen
10531d2166 P2P: Fix provisioning info clearing after successful WPS step
Previously, this provisioning info was cleared using the P2P Interface
Address of the GO as the key. That did not always work in the case the
where we joined an already running group. This could result in the next
connection to that same GO skipping provision discovery. Fix this by
finding the peer entry based on its P2P Device Address instead of the
P2P Interface Address which may not always be set.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-03-01 22:06:03 +02:00
Jouni Malinen
75c208b9db P2P: Fix p2p_cancel to return success if GO Negotiation is stopped
If a GO Negotiation peer is found, wpas_p2p_stop_find() stops the
negotiation and p2p_cancel can return success.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-01 01:16:06 +02:00
Jouni Malinen
8e64f258c6 P2P: Optimize provisioning step scan for join-a-group sequence
Copy the SSID and frequency of the selected group into go_params in
join-a-running-group case so that the scan optimization can be used for
the provisioning step similarly to the case of group formation. This
uses a specific SSID and a single channel scan to avoid unnecessary
frames during the step.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-29 00:22:58 +02:00
Jouni Malinen
360182ed7c P2P: Advertise immediate availability of WPS credential
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).

For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-27 23:14:35 +02:00
Jouni Malinen
dddc70455b P2P: Add more debug on group idle timeout
This makes it easier to debug issues with P2P group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-19 18:16:34 +02:00
Jouni Malinen
a7a30b90e5 P2P: Fix group idle timer cancellation on group removal
The wpas_p2p_group_idle_timeout was getting cancelled in the beginning
of wpas_p2p_group_delete(). However, in the case of P2P client role,
this function called wpa_supplicant_deauthenticate() next and that ended
up changing state to WPA_DISCONNECTED which resulted in
wpas_p2p_notif_disconnected() rescheduling the timeout. This left the
unexpected timeout behind after the group was removed. If another group
operation was started within P2P_MAX_CLIENT_IDLE (10) seconds, that
timeout could end up terminating the group while it was still being set
up.

Fix this by reordering wpas_p2p_group_delete() to cancel the group idle
timeout only after having called wpa_supplicant_deauthenticate(). The
group idle timeout is still rescheduled, but it gets removed immediately
afterwards when the actual group information is being cleared.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-19 18:10:20 +02:00
Jouni Malinen
6f3bc72be0 P2P: Allow channels to be removed from P2P use
A list of disallowed frequencies for P2P channel list can now be
configured with P2P_SET disallow_freq. The frequencies (or frequency
pairs) are comma separated. For example:
wpa_cli p2p_set disallow_freq 2462,5000-6000

The allowed P2P channel list is constructed by removing explicitly
disallowed channels from the channel list received from the driver.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-17 22:57:13 +02:00
Jouni Malinen
e22d4d957b Remove the GPL notification from files contributed by Atheros
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-11 19:39:36 +02:00
Piotr Nakraszewicz
d9a0f66696 P2P: Do not expire GO peer entry during group rekeying
If wpas_go_connected() is called during group rekeying the P2P GO peer
will expire. To prevent that check if group rekeying is not in progress.
2012-02-11 10:54:40 +02:00
Jouni Malinen
c427ac9211 P2P: Set Invitation Type to 1 for GO inviting to a persistent group
When a GO is operating a persistent group and invites a peer that has
been a P2P client in that persistent group, the Invitation Type in the
Invitation Request frame can be set to 1 to indicate that this is a
reinvocation of a persistent group. Do this based on the maintained
list of P2P clients that have been provided the credentials to this
group.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-06 21:54:36 +02:00
Jouni Malinen
f63b854215 P2P: Wait for PD-before-join response
Even though the Provision Discovery Response frame from PD-before-join
does not really provide any additional information, it can be better to
wait for it before starting the join operation. This adds a minimal
extra latency in the most common case and cleans up the sequence of
driver operations and debug log by avoiding potential processing of the
Provision Discovery Response while already running a scan for the actual
connection.

If transmission of Provision Discovery Request fails, join operation is
started without the additional wait. In addition, a new timeout is used
to start the join if Provision Discovery Response is lost for any
reason.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-05 20:52:24 +02:00
Jouni Malinen
c19316354e P2P: Skip event notification on PD Response in join-group case
Provision Discovery is used as a notification to the GO in the case we
are about join a running group. In such case, there is not much point in
indicating the provision discovery response events to external programs
especially when the PIN-to-be-displayed was different from the one
returned for the p2p_connect command. Skip this confusing event
completely for join-a-running-group case.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-05 20:20:36 +02:00
Dmitry Shmidt
df509539d4 Let wpa_supplicant_deinit_iface() know that process is terminating
This will be needed to be able to move ctrl_iface TERMINATING event to
the end of interface removal.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2012-01-29 20:15:48 +02:00
Jouni Malinen
b1aebbc427 P2P: Do not expire peer entry if we are connected to the peer
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-01-25 17:27:47 +02:00
Jouni Malinen
433cd2ce65 Stop sched_scan in number of cases where it should not be running
When a P2P group is removed, we better not leave possibly started
sched_scan running. This could happen when a separate group interface
was not used.

In addition, it looks safer to explicitly stop sched_scan before
starting P2P Listen or Find operations to make sure the offloaded
scanning is not running when doing similar P2P operations.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-01-23 18:26:09 +02:00
Jouni Malinen
6d92fa6e92 P2P: Allow Device ID to be specified for p2p_find command
dev_id=<P2P Device Addr> can now be specified as an argument to
p2p_find to request P2P find for a specific P2P device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-01-08 09:25:29 -08:00
Jouni Malinen
e91829f9ac P2P: Stop remain-on-channel prior to starting join-a-group client
This fixes issues with drivers that do not handle concurrent
remain-on-channel and scan operations in a case where Provision
Discovery Response frame is not received to stop the Action frame
handshake.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-29 13:28:17 +02:00
Neeraj Kumar Garg
b8349523e4 P2P: Reject p2p_group_add if forced frequency is not acceptable
If the freq parameter is specified and we are already running legacy STA
on a different frequency with a driver that does not support
multi-channel concurrency, reject p2p_group_add. Same code already
exists in the path of P2P connection with go negotiation but is missing
for autonomous GO.

Signed-hostap: Neeraj Garg <neerajkg@broadcom.com>
2011-12-27 23:21:45 +02:00
Jouni Malinen
d7e70476f2 P2P: Use global->p2p_dev_addr instead of parent->own_addr
Start using global->p2p_dev_addr more consistently as the P2P Device
Address.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-25 23:58:03 +02:00
Jouni Malinen
fbdcfd577a P2P: Maintain a list of P2P Clients for persistent group on GO
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-22 22:47:41 +02:00
Jouni Malinen
87f841a140 P2P: Show persistent group info on P2P_PEER data
Add "persistent=<network id>" line to P2P_PEER ctrl_iface data
if a persistent group credentials are available for this peer.
This makes it easier for external programs to figure out when
a persistent group could be re-invoked with this peer.

For now, this information is only available on the P2P client,
but similar information can be added for GO once a list of P2P
clients is maintained with the persistent group data.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-22 21:45:20 +02:00
윤민홍
3b655312d4 P2P: Send D-Bus ServiceDiscoveryRequest signal for external SD processing
wpas_notify_p2p_sd_request() needs to be called when
p2p_sd_over_ctrl_iface is set to provide SD events over D-Bus similarly
to the ctrl_iface events.
2011-12-22 00:34:29 +02:00
Jouni Malinen
c81066153c P2P: Use hardcoded idle timeout of 10 seconds in P2P client role
The p2p_group_idle configuration parameter is much more useful for
GO role, so use a separate hardcoded value of 10 seconds in P2P
client role. In practice, this means that the P2P client role will
automatically tear down the group when the GO tears down the group.

The 10 second timeout is enough to recover from temporary disconnections
without unnecessary tearing down the group if the GO is still present
and allows the client to connect.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 22:21:22 +02:00
Jouni Malinen
4c2c675173 P2P: Fix disconnect event not to increase idle timeout
When P2P client is processing a disconnection event, make sure the P2P
idle timeout does not get increased, i.e., set a new timeout only if no
timeout is in use. wpa_state changes between DISCONNECTED and SCANNING
can generate multiple calls to wpas_p2p_notif_disconnect() and
previously this was enough to force the idle timeout never hit in
practice when in P2P client role.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 22:18:42 +02:00
Jouni Malinen
1ef2f7ffcf P2P: Fix Provision Discovery channel for some join-GO cases
The Provision Discovery Request needs to be sent on the operating
channel of the GO and as such, the frequency from the BSS table
(scan results) need to override the frequency in the P2P peer
table that could be based on the Listen channel of the GO.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 17:21:25 +02:00
Reinette Chatre
e5a359cf7e P2P: Make GO negotiation peer and group information available over D-Bus
The GO negotiation response is very cryptic at the moment. For a success
message we only know on which interface the negotiation succeeded, not
which peer. For a failure we know the interface also and a status code
(number).

It will be very useful for clients to know upon receipt of such a message
which peer the negotiation occurred with.

Now that the peer information is available and the API is changed
already, the function composing the D-Bus message might as well include
all GO negotiation information. This is done with a dict to make things
easier on clients if this result information changes down the line.

Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-12-18 16:52:33 +02:00
Jouni Malinen
5506d18418 Fix compiler warning with CONFIG_NO_STDOUT_DEBUG=y
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:19:24 +02:00
Jouni Malinen
7165c5dc1f P2P: Fix 32-bit compiler warnings on service discovery reference
Convert core wpa_supplicant code to use u64 instead of void * for the
P2P service discovery reference. Use uintptr_t in type casts in
p2p_supplicant.c to handle the conversion without warnings.

Note: This needs to be revisited for 128-bit CPU where sizeof(void *)
could be larger than sizeof(u64).

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:06:34 +02:00
Jouni Malinen
e3a0706b47 P2P: Fix Provision Discovery name in debug messages
Some debug messages used incorrect name for Provision Discovery.
Replace "Provisioning Discovery" with "Provision Discovery".

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 17:36:38 +02:00
Vitaly Wool
c3daaf3325 Skip WPS PBC overlap detection if P2P address is the same
WPS overlap detection can detect false overlap if a P2P peer
changes UUID while authentication is ongoing. Changing UUID
is of course wrong but this is what some popular devices do
so we need to work around it in order to keep compatibility
with these devices. There already is a mechanism in WPS
registrar to skip overlap detection if P2P addresses of two
sessions match but it wasn't really triggered because the
address wasn't filled in in the caller function.

Let's fill in this address and also clean up WPS PBC sessions
on WSC process completion if UUID was changed.

Signed-hostap: Vitaly Wool<vitalywool@gmail.com>
2011-12-11 12:03:18 +02:00
Jouni Malinen
502618f7c1 P2P: Clean up group formation on network block removal
If a P2P group network block is removed for any reason (e.g., wps_cancel
command) while the interface is in group formation, remove the group
formation timeout and indicate failure immediately. Previously, this
type of operations could end up leaving the timeout running and result
in somewhat unexpected group formation failure events later.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-10 12:56:42 +02:00
Jouni Malinen
c3f4278445 P2P: Add group ifname to P2P-PROV-DISC-* events
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-06 21:57:17 +02:00
Jithu Jance
ec437d9e74 P2P: Skip duplicated provision discovery on join
If p2p_prov_disc join command is used prior to p2p_connect join,
skip the duplicated provision discovery exchange.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2011-12-06 21:44:57 +02:00
Jithu Jance
8c5f730983 P2P: Add optional "join" argument for p2p_prov_disc command
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2011-12-06 21:28:02 +02:00
Jouni Malinen
a9e02d593d P2P: Clear show_group_started on GO start
The show_group_started variable could be left to 1 based on an earlier
failed attempt to start P2P client operation. This can result in
unexpected P2P-GROUP-STARTED event when a GO is started without group
formation (e.g., re-invoke a persistent group or start an autonomous
GO). Avoid this by explicitly clearing show_group_start when setting up
the GO.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 10:49:26 +02:00
Jouni Malinen
9dbf53fe35 P2P: Send Listen state Probe Response frames without retries
Use the no-ACK send_mlme request to transmit Probe Response frames
in P2P Listen state. This reduces number of unnecessary transmissions
if the peer device has already moved away from the channel. It will most
likely go through Search state multiple times anyway, so even if the
response were to be lost, a new retry will happen at higher layer.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-19 19:15:10 +02:00
Johannes Berg
6cad95db72 P2P: Simplify code in wpas_p2p_connect()
There's some duplicated code there that can be simplified
with just a single new variable.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-11-18 23:32:03 +02:00
Jouni Malinen
19df9b0761 Mark local functions static
These functions are not used outside the file in which they are defined.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-18 21:53:36 +02:00
Jouni Malinen
2bb747e232 P2P: Cancel previous operation before starting new p2p_listen
Some drivers do not handle concurrent remain-on-channel operation
requests, so run p2p_stop_find() prior to starting p2p_listen. This
addresses some issues with P2P_LISTEN command being issues again
while already in Listen state.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-17 16:21:11 +02:00
Jouni Malinen
39185dfa54 P2P: Wait until ongoing scan completes before starting P2P find
The P2P_FIND command was failing if it was issued at the moment when
a scan operation was in progress. Avoid returning failure in this
case by scheduling the P2P find to start once the ongoing scan is
completed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-15 21:28:35 +02:00
Jouni Malinen
adc33680e3 Do not add P2P IE into Beacon/Probe Response if P2P is disabled
P2P IE was incorrectly added in wpa_supplicant AP mode even if P2P
function was not actually enabled.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-14 16:26:45 +02:00
Jouni Malinen
97bcd562eb Remove disable_11b_rates() driver_ops
This function was used unconditionally if wpa_supplicant build
includes CONFIG_P2P=y. Adding a separate driver_ops for such use
is not really useful since the driver wrappers can do the same
internally. Remove this driver_ops and move matching functionality
into driver_nl80211.c which was the only driver wrapper using
this driver_ops callback.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-29 22:25:28 +03:00
Jouni Malinen
b106173a82 Add no_cck parameter for send_action() driver_ops
This can be used to apply the no-CCK rule conditionally depending on
which frame is being sent. The no-CCK rule applies only for P2P
management frames while SA Query and FT use cases do not have similar
restrictions.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-29 21:49:46 +03:00
Jithu Jance
b49d6ccb74 P2P: Fix frequency in the P2P_EVENT_GROUP_STARTED event
P2P Client did not show correct frequency in the control interface
event P2P_EVENT_GROUP_STARTED. Fix that by using the frequency from
the BSS table or association event.
2011-10-28 22:26:30 +03:00
Jithu Jance
3074d8f12d P2P: Notify device expiry via P2P-DEVICE-LOST event
This patch will notify applications listening over control socket about
the device expiry [from p2p peer list].
2011-10-28 22:13:18 +03:00
Jithu Jance
2d4f15d683 P2P: Stop any on-going "p2p_find" on creating an Autonomous GO
This patch stops any on-going "p2p_find" on creating an Autonomous GO.
This is already taken care in case of invoking a persistent GO. GO as
such will be advertising via the beacons for other devices to discover.
So normally the GO doesn't need to do a p2p_find until and unless it
wants to invite a P2P Client. In case of Invite scenario, logically it
is better to do a explicit discover [via user intervention] after the GO
is created. This patch will help to reduce battery wastage [due to
p2p_find operations] in scenarios where user creates a GO and doesn't
initiate a connection.
2011-10-26 01:28:51 +03:00
Jouni Malinen
acc247b260 P2P: Advertise Persistent Reconnect group capability
The persistent_reconnect configuration parameter was used to decide
whether to accept invitation to re-establish a persistent group.
However, this was not being advertised in the Group Capability bitmap.
Add the Persistent Reconnect bit based on this configuration to GO
Negotiation frames and Beacon/Probe Response frames from the GO.
2011-10-24 17:29:37 +03:00
Christian Lamparter
6bf731e8ce wpa_supplicant: Unify hardware feature data
The hardware feature data is required in several different places
throughout the code. Previously, the data was acquired and freed on
demand, but with this patch wpa_supplicant will keep a single copy
around at runtime for everyone to use.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2011-10-23 17:21:50 +03:00
Jouni Malinen
17fbb751e1 Remove user space client MLME
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
2011-10-22 22:45:38 +03:00
Janusz Dziedzic
a7fd39bb5d P2P: Cleanup AP callbacks when removing the group
Clear the P2P GO callback parameters when removing the group to avoid
using these for non-P2P AP mode.

This is a fix for the bug I found in the following scenario:

A) p2p_group_add
A) p2p_group_remove wlan0
A) add_n
A) set_n 0 ssid "testap"
A) set_n 0 key_mgmt NONE
A) set_n 0 mode 2
A) set_n 0 frequency 2412
A) enable_n 0

B) try connect to testap

Authentication request will be always rejected because of
HOSTAPD_ACL_REJECT and not cleaned callbacks when group removed.
2011-10-12 21:06:39 +03:00
Jouni Malinen
24f6497c34 GAS: Use off-channel operations for requests
This separates off-channel Action frame TX/RX from P2P into a generic
implementation that can now be used both for P2P and GAS needs.
2011-09-29 22:19:51 +03:00
Jouni Malinen
206e1f422f P2P: Provide mechanism for figuring out p2p_scan_ie() buffer need
The new function, p2p_scan_ie_buf_len(), can be used to figure out
how large a buffer needs to be allocated for p2p_scan_ie() use. This
makes it easier to add new data into the buffer without forcing all
callers to be updated to use a larger buffer.
2011-09-29 22:18:23 +03:00
Jouni Malinen
303f60d39b P2P: Do not request station mode scans during P2P operations
The P2P search mechanism depends on the same scan functionality that
is used for station mode scans. If these operations are being used
at the same time, scan result processing is not handled properly.
Avoid unexpected behavior by delaying station mode scan requests
if a P2P operation is in progress.

Among other things, this allows the station mode connection attempt
to be continued after a P2P find or group formation has been completed
if the interface is available (i.e., when the P2P group uses a
separate virtual interface).
2011-09-29 16:53:55 +03:00
Jouni Malinen
0c96fd6d03 P2P: Do not leave P2P scan handler registered if scan fails
If the initial attempt to start a scan for p2p_find fails, an error
is reported. However, the P2P scan handler and search state was
left behind. That can result in unexpected behavior when the next
non-P2P scan results are indicated. Avoid this by clearing the
P2P search state on failure.
2011-09-29 16:52:23 +03:00
Johannes Berg
3a26a2c9df P2P: Fix action done handling for driver-based off-channel TX
The action done handling needs to abort an off-channel period since one
might have been used for example for GO negotiation and after action
done the code assumes it can start a new off-channel period.

This fixes a bug I introduced when adding support for
in-kernel off-channel transmissions.

Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-09-22 00:57:27 +03:00
Rajkumar Manoharan
47185fc788 P2P: Remove CCK supported rates when running P2P scan
This allows drivers to disable CCK rates from Probe Request frames.
For nl80211, this is currently applying only to the supported rates
element(s), but this mechanism could be extended to address TX rate
control masking, too, to lessen need for global rate disabling.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2011-09-10 22:40:30 +03:00
Jouni Malinen
07fecd3915 P2P: Remove Label config method
The P2P specification (3.1.4.3) disallows use of the Label configuration
method between two P2P devices. This was previously enforced at upper
level, but the obsolete code can be removed from wpa_supplicant. This
adds a bit more strict enforcement of the policy, but should not result
in practical differences since no known P2P implementation uses Label
config method.
2011-09-08 16:40:03 +03:00
Jouni Malinen
04a85e4401 P2P: Filter Probe Request frames based on DA and BSSID in Listen state
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
2011-07-15 20:28:46 +03:00
Jouni Malinen
21fe9e757e P2P: Use consistent checking of ssid != NULL 2011-07-15 14:20:31 +03:00
Jouni Malinen
ab1dee81a2 P2P: Remove dead code from wpas_p2p_connect()
The case of joining a running group is handled before this location
and the P2P client iftype is assigned at a callback function for that
case.
2011-07-15 13:57:31 +03:00
Jouni Malinen
20a0b03deb Clear WPA and EAPOL state machine config pointer on network removal
Make sure that the WPA and EAPOL state machines do not hold a pointer
to a network configuration that is about to be freed. This can fix
potential issues with references to freed memory.
2011-06-27 19:02:24 +03:00
Jayant Sane
2463ba70e2 P2P: Update listen and operating channel from P2P D-Bus
Some P2PDevice properties were not updated in p2p->cfg structure:
reg_class, channel, op_reg_class, and op_channel. Hence, update p2p->cfg
parameters through p2p core calls in wpas_p2p_update_config().

Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-25 12:08:43 +03:00
Jayant Sane
3734552f15 P2P: Add WpsFailed signal in P2P D-Bus
Signal is triggered if an error occurs during WPS provisioning phase.

Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-25 11:47:04 +03:00
Jayant Sane
c2762e410f P2P: Update D-Bus network object semantics during group formation
Do not emit network objects during P2P group formation since such
network objects can confuse certain apps. Instead, a persistent group
object is created to allow apps to keep track of persistent groups.
Persistent group objects only represent the info needed to recreate the
group.

Also fixes a minor bug in the handling of persistent group objects
during WPS operations.

Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-23 21:25:13 +03:00
Jouni Malinen
7dcdcfd68d P2P: Start GO without extra scan step
There are some corner cases, where the wpa_supplicant_req_scan() call
may end up scheduling a scan even if we are about to start a GO. Avoid
this by explicitly marking the GO network to be selected for the next
connection.
2011-06-21 11:47:03 +03:00
Jean-Michel Bachot
4b6baa2f5e P2P: Add group started notification
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-06-12 14:35:37 -07:00
Johannes Berg
dd8a7e0547 P2P: Add wpas_notify_p2p_provision_discovery()
Add a notification for P2P provision discovery status/result.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-06-12 14:31:56 -07:00
Jouni Malinen
64f992652d P2P: Include operating class 124 (channels 149,153,157,161)
When using the p2p_oper_reg_class configuration option instead of
p2p_group_add freq parameter, the operating class 124 was not
processed correctly. Include that class in the list of 5 GHz classes
for the p2p_oper_reg_class to resolve this.
2011-05-16 21:07:05 +03:00
Jouni Malinen
714b8b5378 P2P: Fix memory leak in UPnP service discovery request processing 2011-04-14 01:33:26 +03:00
Jouni Malinen
62c0d27ed3 P2P: Clear go_dev_addr for group started events if it is not known
Better make sure the address value included in the event message gets
cleared in case the GO Device Address is not known for some reason.
Previously, this could potentially have been some random data from
stack should we ever hit the case where wpa_s->current_ssid is not
set (which should not really happen in normal use cases).
2011-04-13 22:03:52 +03:00
Jouni Malinen
b6e0180035 P2P: Add more WPS attributes into Listen state Probe Response
Configure more WPS attributes in the P2P module and use them
when generating WSC IE for Probe Response frames in Listen state.
2011-03-28 15:24:12 +03:00
Jean-Michel Bachot
046ef4aa67 P2P: Add option for requested device type in P2P search/scan
With this, p2p_find can be extended to find certain requested device
types.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-19 12:57:46 +02:00
Jean-Michel Bachot
f95cac271b P2P: Allow adding of WPS vendor extension attributes
This adds the ability to add WPS vendor extension attributes in P2P
frames, like GO Negotiation and Probe Response frames.

Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-19 12:22:18 +02:00
Johannes Berg
2f646b6e83 WPS: Store (secondary) device type as binary
Instead of converting back and forth from the string representation,
always use the binary representation internally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-17 18:50:22 +02:00
Jouni Malinen
e17a2477db nl80211: Extend bridge add/del operations for secondary BSSes
Previously, only the main interface was added to a bridge. Extend this
to apply to all configured BSSes.
2011-03-15 13:02:49 +02:00
Konguraj(Raj) Kulanthaivel
43a26f606c P2P: Add wpas_notify_p2p_sd_response
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:47:34 +02:00
Konguraj(Raj) Kulanthaivel
e1653cac23 P2P: Add wpas_notify_p2p_sd_request
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:45:39 +02:00
Jean-Michel Bachot
5ccdf84f0d P2P: Add invitation result notification
Add a notification function for the result of an invitation.

Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:40:21 +02:00