When STA is performing roam from WPA3 AP to WPA2 AP, the STA was
including key mgmt FT-SAE instead of FT-PSK in FT Authentication request
RSNE when using driver-based SME. This is because the RSNE/MDE/FTE were
updated and forwarded to the driver using the NL80211_CMD_UPDATE_FT_IES
command before updating key mgmt properly. Because of this, the AP is
rejecting FT Authentication request with WLAN_REASON_UNSPECIFIED reason
code which is due to the invalid keymgmt in RSNE.
Fix this by reordering IE population to happen earlier in the sequence
so that the updated key mgmt information can be provided when using
NL80211_CMD_UPDATE_FT_IES.
Signed-off-by: Shiva Sankar Gajula <sgajula@codeaurora.org>
Add user configured vendor IEs for Probe Request frames to default scan
IEs so that these IEs will be included in the Probe Request frames for
the scans issued also by components other than wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit 7b121af26a ("P2P: Delay P2P scan when an external scan is in
progress") added a new argument to p2p_scan_res_handled(), but did not
update this test tool. Fix this by using hardcoded value 0 for the new
delay argument.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Android has a mechanism to extend the driver interface in vendor
specific ways. This implementation of the vendor interface is done in
$(BOARD_WPA_SUPPLICANT_PRIVATE_LIB). Extend this to allow the vendor
events to be provided to this library to facilitate the event
processing.
Introduce a new board configuration via
$(BOARD_WPA_SUPPLICANT_PRIVATE_LIB_EVENT) rather than reusing
$(BOARD_WPA_SUPPLICANT_PRIVATE_LIB) to enable this event handling in the
private library. This is to avoid compilation issues for
wpa_driver_nl80211_driver_event() with the already existing private
library implementations defined with
$(BOARD_WPA_SUPPLICANT_PRIVATE_LIB).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When an external scan is in progress on the same radio, delay the P2P
search operation based on configuration parameter p2p_search_delay. The
"search_delay" configuration done through p2p_find always takes
precedence over this delay value set due to an external scan trigger.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a handler to notify failures to fetch the scan results and provide
an option to override default behavior of requesting a new scan in one
second in such an error condition. Use this new handler mechanism to
continue the p2p_find operation (by invoking p2p_scan_res_handled) for
an interim scenario where the p2p_scan attempt fails to get the scan
results from the driver which can happen, e.g., if there are parallel
updates to the cfg80211 scan results.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
NL80211_CMD_ROAM indication is scheduled via a kernel work queue, while
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH is a vendor event from the
driver. Thus, a race condition can exist wherein the vendor event is
received prior to the NL80211_CMD_ROAM indication.
The processing of this vendor event depends on the NL80211_CMD_ROAM
indication to update the roamed BSS/BSSID information and thus the out
of sequence processing of these events would result in not updating the
right BSS information.
This commit adds a workaround to hold the pending
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event for up to 100 ms in
case NL80211_CMD_ROAM is not received first.
Signed-off-by: Purushottam Kushwaha <pkushwah@codeaurora.org>
After a disconnect command is issued, wpa_supplicant generates a
disconnection event to self and ignores the next disconnection event
coming from the driver. In a race condition in which the driver
generates a connected event due to roaming just before receiving the
disconnect command from userspace, wpa_supplicant processes the
connected event after processing the self-generated disconnection event
and enters WPA_COMPLETED state. The driver sends a disconnection event
after processing the disconnect command sent by wpa_supplicant but the
disconnection event is ignored by wpa_supplicant as the disconnection
event is considered to be a result of locally generated disconnect
command. Thus, wpa_supplicant continues to be in the connected
(WPA_COMPLETED) state though the driver is in disconnected state.
Fix this out-of-sync behavior between the driver and wpa_supplicant by
not ignoring the disconnection event from the driver because of the
locally generated disconnect command sent to the driver if there is a
connection event received after issuing the disconnect command to the
driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Now that wpa_supplicant ignores the unexpected association event in
disconnected-not-trying-to-connect state, this test cases needs to be
modified to avoid incorrect failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If there is a disconnect command from wpa_supplicant immediately after
the driver sends a connection event to userspace but before that event
is received and processed by wpa_supplicant, wpa_supplicant processes
the disconnect command and a self-generated disconnected event first
followed by the connected event received from the driver. As a result
wpa_supplicant moves to the WPA_COMPLETED state. Whereas the driver
processes the disconnect command received from wpa_supplicant after it
sends the connected event and moves to the disconnected state. Due to
this race between the disconnect command from wpa_supplicant and the
connected event from the driver, wpa_supplicant is moving to the
connected state though the driver is moving to the disconnected state
which results in abnormal functionality.
Ignore the connection event coming from the driver when wpa_supplicant
is not trying to connect after a disconnect command is issued but before
the next connect command is issued to fix the above mentioned race
condition.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The response for the respective TWT operations can either be synchronous
or asynchronous (wherever specified). If synchronous, the response to
this operation is obtained in the corresponding vendor command reply to
the user space. For asynchronous case, the response is obtained as an
event with the same operation type.
Drivers shall support either of these modes but not both simultaneously.
The support for asynchronous mode is advertised through the new flag
QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT. If the driver does not
include this flag, it shall support synchronous mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Define the following additional TWT operations:
QCA_WLAN_TWT_GET_STATS, QCA_WLAN_TWT_CLEAR_STATS,
QCA_WLAN_TWT_GET_CAPABILITIES, QCA_WLAN_TWT_SETUP_READY_NOTIFY.
Also define new attributes to qca_wlan_vendor_attr_twt_setup
and qca_wlan_vendor_attr_twt_nudge.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace the implicit boolean checks that used int variables with use of
a more explicit bool variable type.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Support possible band combinations of 2.4 GHz, 5 GHz, and 6 GHz with
QCA_WLAN_VENDOR_ATTR_SETBAND_MASK attribute. Ensure backwards
compatibility with old drivers that are using
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE attribute and supporting only 2.4 GHz
and 5 GHz bands.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The function name for adding frequency lists changed, so this test case
needs a matching change to avoid failures.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This functionality was repeated for couple of times. Use a shared helper
function to avoid code duplication.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
The earlier workaround for UBSAN issues in commit 3b6b3ae581 ("Modify
dl_list_for_each() to not use unaligned access with WPA_TRACE") ended up
using a construction in which the type cast to the containing structure
was compared instead of the struct dl_list pointers. While that worked
around the UBSAN issue, it resulted in a comparison that gcc-10
interprets as being out of bounds for struct dl_list (which it obviously
is since this is to find the start of the containing structure).
Revert that workaround and instead, mark the struct dl_list used within
struct os_alloc_trace to have matching 16 octet alignment as the
containing structure. This is also restoring consistent design for
dl_list_for_each*().
Signed-off-by: Jouni Malinen <j@w1.fi>
This was broken in the kernel in mac80211 for a while, until commit
780a8c9efc65 ("mac80211: do not disable HE if HT is missing on 2.4 GHz")
fixed it.
Add a test for wifi generation on 2.4 GHz in addition to the 5 GHz one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver sends a CQM RSSI threshold event, wpa_supplicant queries
the driver for the signal and noise values. However, it is possible that
by that time the station has already disconnected from the AP, so these
values are no longer valid. In this case, indicate that these values are
invalid by setting them to WPA_INVALID_NOISE.
Previously a value of 0 would be reported, which may be confusing as
this is a valid value.
Since nl80211_get_link_signal() and nl80211_get_link_noise() already set
invalid values for a case of failure, just use the value set by these
functions even if they fail.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Allow to run local/remote process like:
- ubus listen
- logread -f
- tail -f
- wpa_cli
- hostapd_cli
And next wait for specific event(s).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
S1G beacons save a few bytes by not requiring the RSNE in beacon if RSN
BSS is configured. Handle this in wlantest by only clearing RSNE from
the BSS info if frame is a Probe Response frame.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Sweden now allows channel 149 in the updated wireless-regdb. Choose
Japan for the negative test instead.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Add a new hostapd configuration parameters rssi_ignore_probe_request to
ignore Probe Request frames received with too low RSSI.
Signed-off-by: John Crispin <john@phrozen.org>
Add initial_freq_list to wpa_supplicant configuration. This option
allows wpa_supplicant to scan a smaller list of frequencies when it
starts. This in turn allows for a faster connection to an already known
network. This limit applies only for the initial scan operation and does
not restrict other channels from being used in consecutive scans.
Tests have shown this to reduce the amount of time for connecting to a
network from roughly 3 seconds to roughly 0.1 second.
Signed-off-by: Frederik Juul <frederik.juul@3shape.com>
Previously hostapd would not stop transmitting when a DFS event was
detected and no available channel to switch to was available.
Disable and re-enable the interface to enter DFS state. This way, TX
does not happen until the kernel notifies hostapd about the NOP
expiring.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the ability to disable HT/VHT/HE for specific BSS from hostapd.conf.
- Add disable_11ax boolean to hostapd_bss_config.
- Change disable_11n and disable_11ac to bool in hostapd_bss_config.
- Add configuration option to set these disable_11* parameters
(which were previously used only automatically based on incompatible
security parameters to disable HT/VHT).
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Add a test which uses a DFS channel, waits for CAC afterwards successful
mesh join and then triggers a radar event and checks if the mesh comes
up again on the same device.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The hostapd DFS code deinitializes and initializes the AP interface, if
a clean channel switch is not possible. In this case the AP code paths
would deinit the driver, for example nl80211, without wpa_supplicant
code paths getting notice of this.
Therefore add callbacks for wpa_supplicant mesh methods, which are
called on init/deinit of the AP BSS. These callbacks are then used to
handle the reset in the mesh code.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Send mesh group started notification after join completion
callback is called.
Implement outstanding TODO, to leave the mesh network on deinit.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Only change freq params, if ifmsh->freq is set initially, which only
happens if hostapd_get_hw_features in setup_interface2 succeeds.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
The kernel requires indication of DFS handler residing in user space
(NL80211_ATTR_HANDLE_DFS) to enable DFS channels.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Mesh interface would have used its channel parameters that were
configured during initialization even after channel switch due to DFS
radar detection during CAC which could result in a channel switch error.
Fix the error by updating the channel parameters when channel has been
changed from the initial one.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
mac80211 does not allow mgmt tx to use off channel on
DFS channels in non-ETSI domain, because it will invalidate
CAC result on current operating channel.
(mac80211 commit: 34373d12f3cbb74960a73431138ef619d857996f)
Hence don't set offchanok for mgmt tx in case of DFS channels
in non-ETSI.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
ssid->frequency is one of the variables used to get the channel number
from a given frequency. Leaving it as unchanged when pri/sec channel
switch will cause picking up a wrong channel number after applying the
secondary channel offset for HT40 and leads to failing interface
bring-up.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Mesh join function is the last function to be called during mesh join
process, but it's been called a bit earlier than it's supposed to be, so
that some mesh parameter values such as VHT capabilities were not
applied correct when mesh join is in process. Moreover, the current
design of mesh join that is called directly after mesh initialization
isn't suitable for DFS channels to use, since mesh join process should
be paused until DFS CAC is done and resumed after it's done.
The callback will be called by hostapd_setup_interface_complete_sync().
There is a possibility that completing mesh init fails, so add error
handling codes for that.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Define QCA vendor attributes to dynamically configure TX NSS and RX NSS
to be used with QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION commands.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the maximum operating channel width for AP/P2P GO is not specified,
it is auto-selected during configuration. While selecting the channel
width, if VHT is supported and 160 MHz channels are available, 160 MHz
channel width is preferred to 80 MHz.
During the selection of the channel width, the corresponding driver
capabilities were not checked. As a result, the AP/P2P GO configuration
was set to use the available 160 MHz channels even if the driver did not
have capability to support the 160 MHz channel width causing failure to
start the AP/P2P GO.
Fix this by checking the driver support for the 160 MHz channel width
while selecting the channel width for AP/P2P GO.
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
