Commit graph

153 commits

Author SHA1 Message Date
Jouni Malinen
b5c6831201 Add preferred network offload (PNO) functionality
"SET pno <1/0>" ctrl_iface command can now be used to start/stop PNO
with sched_scan driver commands. This will request offloading of
scanning to find any of the enabled networks in the configuration.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-28 16:32:44 +02:00
Jouni Malinen
39185dfa54 P2P: Wait until ongoing scan completes before starting P2P find
The P2P_FIND command was failing if it was issued at the moment when
a scan operation was in progress. Avoid returning failure in this
case by scheduling the P2P find to start once the ongoing scan is
completed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-15 21:28:35 +02:00
Fu Yingang
a4cef16279 Correct a spelling mistake
The word "targer" in the comments for pending_bssid of
wpa_supplicant data structure should be "target".
2011-11-13 18:35:15 +02:00
Jouni Malinen
01a1749156 Fix TKIP countermeasures stopping in deinit paths
The eloop timeout to stop TKIP countermeasures has to be canceled
on deinit path to avoid leaving bogus timeouts behind.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-30 12:53:20 +02:00
Jouni Malinen
b106173a82 Add no_cck parameter for send_action() driver_ops
This can be used to apply the no-CCK rule conditionally depending on
which frame is being sent. The no-CCK rule applies only for P2P
management frames while SA Query and FT use cases do not have similar
restrictions.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-29 21:49:46 +03:00
Jithu Jance
5cbd88d921 P2P: Fix wpa_supplicant crash on P2P WPS PBC overlap case
Once PBC overlap detected when using dynamic group interfaces, the wpa_s
corresponding to P2P group interface is freed. This patch avoids
accessing the wpa_s data structure after it is freed. This fixes a
possible crash in P2P client role in such a case.
2011-10-24 23:37:39 +03:00
Arik Nemtsov
c58ab8f249 TDLS: Get TDLS related capabilities from driver
Put glue code in place to propagate TDLS related driver capabilities to
the TDLS state machine.

If the driver doesn't support capabilities, assume TDLS is supported
internally.

When TDLS is explicitly not supported, disable all user facing TDLS
operations.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
2011-10-23 22:15:15 +03:00
Christian Lamparter
6bf731e8ce wpa_supplicant: Unify hardware feature data
The hardware feature data is required in several different places
throughout the code. Previously, the data was acquired and freed on
demand, but with this patch wpa_supplicant will keep a single copy
around at runtime for everyone to use.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2011-10-23 17:21:50 +03:00
Jouni Malinen
17fbb751e1 Remove user space client MLME
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
2011-10-22 22:45:38 +03:00
Jouni Malinen
7a25f29d89 Interworking: Use unsigned integer for bitfield
Signed integer with one-bit value does not make much sense, so clean
this up by using an unsigned integer instead.
2011-10-20 20:49:21 +03:00
Jouni Malinen
b02fe7ff32 Interworking: Add commands for network selection
This adds the basic mechanism for running through network selection:
scan, ANQP fetch, network selection, and connection. Actual rules for
network selection and the creation of the network block are still
missing, but will be added in separate commits.
2011-10-16 23:55:34 +03:00
Jouni Malinen
afc064fe7a Interworking: Add ANQP query requests
Add mechanism for using GAS/ANQP to query Interworking related
information from APs. The received information is stored in the BSS
table and can be viewed with ctrl_iface BSS command.

New ctrl_iface command ANQP_GET can be used to fetch ANQP elements from
a specific AP. Additional commands FETCH_ANQP and STOP_FETCH_ANQP can be
used to initiate and stop an iteration through all APs in the BSS table
that indicate support Interworking to fetch ANQP elements from them.
2011-10-16 23:55:34 +03:00
Luciano Coelho
b59e6f267b Add filter support to scheduled scans
Pass SSIDs to be matched in scheduled scan results. Only the SSIDs
that are included in the match lists will be reported by the driver,
so the filtering can be offloaded to the hardware and the power
consumption can be reduced.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-15 18:53:14 +03:00
Luciano Coelho
cbdf3507e9 Add scheduled scan driver operations
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.

This commit adds initial scheduled scan support operations and events.

Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-10-15 18:53:13 +03:00
Jouni Malinen
24f6497c34 GAS: Use off-channel operations for requests
This separates off-channel Action frame TX/RX from P2P into a generic
implementation that can now be used both for P2P and GAS needs.
2011-09-29 22:19:51 +03:00
Jouni Malinen
04ea7b7947 GAS: Add a generic GAS query module
This implements GAS request mechanism that is aimed at being used to
replace use case specific GAS/ANQP implementations in the future.
Compared to the earlier implementation in P2P SD, this implementation
includes support for multiple concurrent requests and more thorough
validation of frames against the pending query data.

GAS header processing, including comeback and reassembly, are handled
within gas_query.c and the users of this module will only need to
provide the Query Request and process the (possibly reassembled)
Query Response.
2011-09-29 22:19:15 +03:00
Jouni Malinen
22628eca34 Support driver-based BSS selection in ap_scan=1 mode
If the driver indicates that it supports BSS selection (including
roaming within an ESS) with WPA_DRIVER_FLAGS_BSS_SELECTION, modify
ap_scan=1 mode to behave like ap_scan=2 mode for BSS selection.

The initial scan is still done to avoid the need for strict
configuration of or security parameters (e.g., to figure out whether
TKIP or CCMP is being used as the group cipher). However, when
requesting the driver to connect, the bssid and freq parameters are
not provided to leave the driver in control of selecting which BSS
to use and to allow the driver to decide when to roam.
2011-09-26 14:57:23 +03:00
Jouni Malinen
64fa840a97 nl80211: Fix WPA_VERSIONS attribute for Connect command
The previous code was trying to figure out which WPA version is
used based on the extra IEs requested for Association Request. That
did not work properly in cases where non-WPA networks are used with
some extra IEs. Fix this by using more robust mechanism for passing
the WPA versions from core wpa_supplicant to the driver_ops
associate().
2011-09-02 20:40:23 +03:00
Jayant Sane
c2762e410f P2P: Update D-Bus network object semantics during group formation
Do not emit network objects during P2P group formation since such
network objects can confuse certain apps. Instead, a persistent group
object is created to allow apps to keep track of persistent groups.
Persistent group objects only represent the info needed to recreate the
group.

Also fixes a minor bug in the handling of persistent group objects
during WPS operations.

Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-23 21:25:13 +03:00
Jouni Malinen
7dcdcfd68d P2P: Start GO without extra scan step
There are some corner cases, where the wpa_supplicant_req_scan() call
may end up scheduling a scan even if we are about to start a GO. Avoid
this by explicitly marking the GO network to be selected for the next
connection.
2011-06-21 11:47:03 +03:00
Johannes Berg
9abafccc0d DBus: Add support for P2P primitives
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-06-12 15:08:19 -07:00
Jouni Malinen
38e24575c1 random: Add support for maintaining internal entropy store over restarts
This can be used to avoid rejection of first two 4-way handshakes every
time hostapd (or wpa_supplicant in AP/IBSS mode) is restarted. A new
command line parameter, -e, can now be used to specify an entropy file
that will be used to maintain the needed state.
2011-05-31 20:07:11 +03:00
Dmitry Shmidt
67b9bd089b Make scan interval configurable
It is now possible to configure the the time in seconds that
wpa_supplicant waits before requesting a new scan after failing to find
a suitable network in scan results.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2011-04-11 23:14:38 +03:00
Sam Leffler
78633c3709 wpa_supplicant: Parameterize BSS table expiration age + count
Replace compile-time BSS cache expiration age and scan count by config
parameters that can be set via wpa_cli and the new D-Bus API. The latter
is done with interface properties BSSExpireAge and BSSExpireCount.
2011-03-20 12:40:59 +02:00
Paul Stewart
cf83fb0b5b wpa_supplicant: Add wpa_supplicant_get_eap_mode method
Signed-off-by: Paul Stewart <pstew@google.com>
2011-03-15 13:53:08 +02:00
Johannes Berg
11fb02be67 P2P: Fix p2p_long_listen
There are two issues with p2p_long_listen:
 1) max_remain_on_channel is assumed to be 5 seconds,
 2) if max_remain_on_channel is not a full multiple of
    seconds, accounting breaks.

Fix these by converting p2p_long_listen to ms and
tracking it according to max_remain_on_channel.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-01 18:09:38 +02:00
Johannes Berg
190b9062b2 P2P: Add option for offloading off-channel TX to the driver
With the new kernel functionality coming to Linux to allow off-channel
TX, we can take advantage of that in the P2P code that currently uses
remain-on-channel. If a driver advertises support for it, it will be
asked to handle off-channel TX by itself.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-12-29 13:59:17 +02:00
Jouni Malinen
7d878ca769 Use SA Query procedure to recovery from AP/STA state mismatch
If a station received unprotected Deauthentication or Disassociation
frame with reason code 6 or 7 from the current AP, there may be a
mismatch in association state between the AP and STA. Verify whether
this is the case by using SA Query procedure. If not response is
received from the AP, deauthenticate.

This implementation is only for user space SME with
driver_nl80211.c.
2010-12-19 11:58:00 +02:00
Jouni Malinen
0f85ef5cf0 P2P: Use larger pending_interface_name buffer
In theory, the interface name could be longer than IFNAMSIZ in
some systems, so use the same size buffer for this field as is
used with the main interface name.
2010-11-26 15:49:26 +02:00
Jouni Malinen
0fb337c121 Extend load balancing optimization in BSS blacklisting
Move the previously SME specific optimization code into generic
function that can be used from non-SME code, too, and use it to
handle disconnection events. In other words, allow disconnection
event to trigger similar optimized scanning case to handle a
common load balancing mechanism. If there is another BSS in the
same ESS when we receive a disconnection event, scan only the
known frequencies of such other BSSes on the next attempt to
speed up recovery.
2010-11-26 11:36:03 +02:00
Jouni Malinen
f47d639d49 SME: Optimize recovery from common load balancing mechanisms
When authentication or association fails when trying to connect to
a BSS in an ESS that has multiple BSSes based on previous scans,
limit the first recovery scan to only the known channels that has
been seen previously. This speeds up recovery in some of the most
commonly used load balancing mechanisms in enterprise WLAN
networks.
2010-11-25 22:51:56 +02:00
Jouni Malinen
9b1ab931b1 P2P: Allow multiple scan runs to find GO for p2p_connect join
If the GO is not found, we cannot send Provisioning Discovery Request
frame and cannot really connect anyway. Since the Provisioning
Discovery is a mandatory part, it is better to continue join-scan
until the GO is found instead of moving to the next step where
normal connection scan is used (PD would not be used from there).

Use a limit of 10 scan attempts for p2p_connect join to avoid getting
in infinite loop trying to join. If the GO is not found with those
scans, indicate failure (P2P-GROUP-FORMATION-FAILURE) and stop the
join attempt.
2010-11-15 16:15:38 +02:00
Anil Gathala Sudha
7cfc4ac319 P2P: Add support for automatic channel selection at GO
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.

p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
2010-11-10 13:33:47 +02:00
Jouni Malinen
0ae2aa14a5 Fix compiler warning from previous commit 2010-10-27 11:31:32 +03:00
Jouni Malinen
2f9c6aa665 Fix memory leak in P2P build without MLME
The ieee80211_sta_free_hw_features() function is now used outside
the MLME code, so better make sure it gets included in the build
to avoid leaking memory.
2010-10-27 11:26:46 +03:00
Jouni Malinen
c973f3868a P2P: Remove P2P group on driver resource becoming unavailable
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.

When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
2010-10-25 19:16:11 +03:00
Jouni Malinen
3071e18109 P2P: Add mechanism for timing out idle groups
A new configuration parameter, p2p_group_idle, can now be used to set
idle timeout value for P2P groups in seconds (0 = no timeout). If set,
this values is used to remove P2P group (both GO and P2P client)
interfaces after the group has been idle (no clients/GO seen) for the
configuration duration.

The P2P-GROUP-REMOVED event is now indicating the reason for group
removal when known. For example:
P2P-GROUP-REMOVED wlan0 GO reason=REQUESTED
P2P-GROUP-REMOVED wlan1 client reason=IDLE
2010-10-25 18:24:15 +03:00
Ardong Chen
0d0a8ca1cc Add option for disabling automatic reconnection on disconnection
ctrl_interface STA_AUTOCONNECT command can now be used to disable
automatic reconnection on receiving disconnection event. The default
behavior is for wpa_supplicant to try to reconnect automatically, i.e.,
to maintain previous behavior.
2010-09-10 10:30:26 -07:00
Jouni Malinen
c4ea4c5c90 P2P: Allow driver wrapper to indicate how many stations are supported
This can be used to limit the number of clients allowed to connect
to the group on the GO.
2010-09-09 07:17:21 -07:00
Jouni Malinen
eea2fd9eff P2P: Add mechanism for configuring UAPSD parameters for group
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.

Following ctrl_interface commands can now be used:

P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode

P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
  (max SP Length is currently ignored)

P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode

P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
2010-09-09 07:17:21 -07:00
Jouni Malinen
72044390f3 P2P: Add support for cross connection
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
2010-09-09 07:17:20 -07:00
Jouni Malinen
6e6963ea86 P2P: Add test mode for SD to force fragmented response 2010-09-09 07:17:19 -07:00
Jouni Malinen
108def931e P2P: Add command for pre-authorizing an invitation to an active group
This is mainly designed for testing and allows p2p_connect join auth
to be used to accept a specific invitation to an active group that
may be received in the future.
2010-09-09 07:17:19 -07:00
Jouni Malinen
3c5126a41f P2P: Set Device Password ID in WPS M1/M2 per new rules
If the P2P client (WPS Enrollee) uses a PIN from the GO (Registrar),
Device Password ID in M1 & M2 is set to Registrar-specified.
2010-09-09 07:17:19 -07:00
Jouni Malinen
07a30a66c3 P2P: Do not schedule new remain-on-channel if waiting for drv event
The driver event for remain-on-channel may be delayed in a way that
allows management-frame-received event to be received before
wpa_supplicant knows that the driver is actually already on the
previously requested channel. We should not request a new
remain-on-channel to send a response to just a frame if we are waiting
for the driver to get to the same channel. Instead, just continue
waiting for the driver event.
2010-09-09 07:17:18 -07:00
Jouni Malinen
b22128efdc P2P: Add initial version of P2P Module 2010-09-09 07:17:17 -07:00
Jouni Malinen
611aea7d41 Allow ctrl_iface SET command to change global config parameters 2010-09-09 07:17:16 -07:00
Jouni Malinen
42f50264c0 WPS: Make fragment size configurable for EAP-WSC peer
"wpa_cli set wps_fragment_size <val>" can now be used to configure the
fragment size limit for EAP-WSC.
2010-09-09 06:07:49 -07:00
Jouni Malinen
24f7694062 Remove get-first-scan-results-before-request optimization
This has already been disabled in most use cases and can result
in problems with some drivers, so better just remove it completely.
2010-07-18 16:11:03 -07:00
Jouni Malinen
c706d5aa17 Add wpa_supplicant AP mode events for Public Action frames 2010-04-11 20:33:33 +03:00
Jouni Malinen
508545f3a9 Add more wpa_supplicant AP mode parameters for the driver wrapper
This makes it easier to configure AP mode for drivers that take care
of WPA/RSN IE generation.
2010-04-11 20:02:01 +03:00
Jouni Malinen
4b768ed0b2 Add registerable callback for wpa_supplicant AP mode completion 2010-04-11 19:59:33 +03:00
Jouni Malinen
8cd82735cb Add an option to request a connection without a new scan 2010-04-11 19:55:40 +03:00
Jouni Malinen
64e58f5189 Add option for overriding scan result handler for a single scan 2010-04-11 19:53:31 +03:00
Jouni Malinen
814782b9fe Allow driver wrappers to indicate maximum remain-on-channel duration 2010-04-11 19:42:37 +03:00
Jouni Malinen
17a4734dc4 Optimize post-WPS scan based on channel used during provisioning
Scan only the frequency that was used during provisioning during the
first five scans for the connection. This speeds up connection in the
most likely case where the AP remains on the same channel. If the AP is
not found after these initial scans, all channels will be scanned.
2010-04-11 19:06:42 +03:00
Jouni Malinen
86d4f806da Add ctrl_iface command for triggering a roam to a specific BSS
'wpa_cli roam <bssid>' can now be used to test roaming within an ESS
(e.g., for FT over-the-air). This command will bypass a new scan and
will select the BSS based on the specified BSSID. It is responsibility
of the caller to make sure that the target AP is in the BSS table.
This can be done, e.g., by running a scan before the roam command,
if needed.
2010-04-10 22:56:55 +03:00
Jouni Malinen
62c72d7299 FT: Process reassoc resp FT IEs when using wpa_supplicant SME 2010-03-13 21:13:18 +02:00
Jouni Malinen
207ef3fb12 Add suspend/resume notifications
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
2010-02-27 18:46:02 +02:00
Jouni Malinen
abd9fafab6 Standardize on a single definition of auth_alg bitfield values 2010-01-03 21:14:40 +02:00
Jouni Malinen
9ba9fa07cc Move wpa_supplicant specific scan code away from src/drivers
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
2010-01-03 18:48:11 +02:00
Jouni Malinen
a8e0505bf0 Use driver event, EVENT_EAPOL_RX, for EAPOL frame indication 2010-01-03 17:44:40 +02:00
Jouni Malinen
8f770587d9 Maintain a pointer to the current BSS table entry 2010-01-02 16:59:19 +02:00
Jouni Malinen
a1fd2ce54e Do not store raw scan results
Use scan results to update the BSS table and to select the BSS for
connection, but do not store the results for longer time.
2010-01-02 16:41:38 +02:00
Jouni Malinen
6fa81a3b3f Use BSS table entry instead of raw scan result for connection 2010-01-02 16:16:02 +02:00
Jouni Malinen
8d923a4acf Only expire scanned BSSes based on new scan results
Get more information about scans when updating BSS table information.
This allows the missing-from-scans expiration rule to work properly
when only partial set of channels or SSIDs are being scanned.
2010-01-02 13:57:44 +02:00
Jouni Malinen
8ddef94bd4 dbus: Share common initialization code for both old and new interface
This was mostly identical code that had been copied for the new D-Bus
API implementation and as such, should really have been shared from
the beginning. In addition, the copied code ended up generating
interesting stack traces since the actual D-Bus connection was being
shared even though the pointer to it was stored in two distinct
data structures. The old D-Bus code ended up dispatching some
D-Bus callbacks which ended up running the new D-Bus code.

Since the private context pointers were mostly identical, everything
seemed to more or less work, but this design was just making things
more complex and potentially very easy to break.
2009-12-31 00:15:56 +02:00
Jouni Malinen
d009a9dac6 Add scan parameter support for client MLME 2009-12-28 13:34:03 +02:00
Jouni Malinen
4832ecd754 Add an option for driver wrappers to report operational frequency 2009-12-28 13:23:13 +02:00
Jouni Malinen
d4bf8f132a Add BSS list sorted by id and add some helper functions
This allows the BSS list to be iterated in order of increasing id
to avoid problems with new scans reordering entries. The order on the
wpa_s->bss list changes with most recently updated entries being moved
to the tail of the list while wpa_s->bss_id list maintains its order
with new entries being added to the tail and old entries being removed
when they expire.
2009-12-28 00:30:38 +02:00
Jouni Malinen
83922c2d34 Add BSS table to track scan results without dropping information
Collect information from scan results into a BSS table that will not
expire information as quickly as scan results where every new scan,
no matter for how limited set of channels/SSIDs, clears all old
information.

For now, this is only used for D-Bus BSS added/removed notifications,
but this will likely be extended to be used internally instead of the
scan results to better support partial scans.
2009-12-27 21:07:47 +02:00
Jouni Malinen
719347511a Get rid of unnecessary typedefs for enums. 2009-12-26 10:35:08 +02:00
Jouni Malinen
1a1bf008cb WPS ER: Delay wpa_supplicant termination to allow unsubscription
Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
2009-12-19 23:47:54 +02:00
Jouni Malinen
fb7842aa51 Remove struct hostapd_rate_data from driver API
In addition to the bitrate, the only other variable in this structure
is used internally in hostapd. Move this structure into hostapd.h and
make the driver API use simpler data structure (array of bitrates).
2009-12-09 21:57:50 +02:00
Jouni Malinen
127608152e Move EAP method registration away from src/eap_{peer,server}
This makes it easier to make a library out of EAP methods without
losing possiblity of binary size optimization by linker dropping
unreferenced code.
2009-12-06 11:28:41 +02:00
Jouni Malinen
8a5ab9f5e5 Fix init2() driver_ops to get the correct global driver context
Need to provide the private driver context, not the wpa_supplicant
global context, in init2() call.
2009-11-28 18:11:16 +02:00
Jouni Malinen
62fa124ce2 nl80211/SME: Use reassociation when roaming within the ESS 2009-11-17 19:25:05 +02:00
Witold Sowa
8fc2fb56e4 wpa_supplicant: new DBus API implementation
This patch implements the new DBus API. Both, the new and the
previous API may work concurrently and may be turned on or off
separately in .config file.
Some features of the new API are:
 - more wpa_supplicant's events are signaled with DBus signals,
 - introspection data (requires libxml2 and may be disabled),
 - CurrentBSS and CurrentNetwork properties,
 - PropertyChanged signal for most of properties,
 - Relatively easy to extend.
.config options for the new API are: CONFIG_CTRL_IFACE_DBUS_NEW=y and
CONFIG_CTRL_IFACE_DBUS_INTRO=y for introspection.

This commit misses couple of parts from the full implementation
(these are still under review):
- fetching all configuration parameters for learning WPS information
- scan result BSS add/remove notification (register_bss() and
  unregister_bss() notification callbacks)
2009-11-09 23:51:59 +02:00
Jouni Malinen
e9bcfebfce WPS: Add initial part of External Registrar functionality
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
2009-11-07 12:41:01 +02:00
Jouni Malinen
d27df100b5 Allow driver and ctrl_interface parameters to be overridden
New wpa_supplicant command line options -o<driver> and -O<ctrl> can
now be used to override the parameters received in add interface
command from dbus or global ctrl_interface. This can be used, e.g.,
to enable control interface when using NetworkManager (add
-O/var/run/wpa_supplicant into the Exec parameter in
/usr/share/dbus-1/system-services/fi.epitest.hostap.WPASupplicant.service).
Similarly, this can be used to use another driver wrapper with
NetworkManager (e.g., -onl80211 to replace WEXT with nl80211).
2009-11-04 20:16:15 +02:00
Sam Leffler
4f34d51abe Do not schedule a new scan if no networks are enabled
This avoids an extra timeout to move to INACTIVE state.
2009-10-14 22:05:58 +03:00
Johannes Berg
0194fedb46 driver_nl80211: Fix MLME key settings for static WEP
Current wpa_supplicant has a bug with WEP keys, it adds a zero-length
sequence counter field to netlink which the kernel doesn't accept.

Additionally, the kernel API slightly changed to accept keys only when
connected, so we need to send it the keys after that. For that to work
with shared key authentication, we also include the default WEP TX key
in the authentication command.

To upload the keys properly _after_ associating, add a new flag
WPA_DRIVER_FLAGS_SET_KEYS_AFTER_ASSOC_DONE indicating that the driver
needs the keys at that point and not earlier.
2009-09-15 10:48:30 +03:00
Jouni Malinen
60b94c9819 Add preliminary background scan and roaming module design
This allows background scanning and roaming decisions to be contained in
a single place based on a defined set of notification events which will
hopefully make it easier to experiment with roaming improvements. In
addition, this allows multiple intra-ESS roaming policies to be used
(each network configuration block can configure its own bgscan module).

The beacon loss and signal strength notifications are implemented for
the bgscan API, but the actual events are not yet available from the
driver.

The included sample bgscan module ("simple") is an example of what can
be done with the new bgscan mechanism. It requests periodic background
scans when the device remains associated with an ESS and has couple of
notes on what a more advanced bgscan module could do to optimize
background scanning and roaming. The periodic scans will cause the scan
result handler to pick a better AP if one becomes available. This bgscan
module can be taken into use by adding bgscan="simple" (or
bgscan="simple:<bgscan interval in seconds>") into the network
configuration block.
2009-09-15 00:08:24 +03:00
Witold Sowa
86b89452f6 Use shared functions for network operations and param changes
Instead of implementing these separately in various control
interface handlers, use shared functions. These add some of the
previously missing notification calls, too, for the affected areas.
2009-09-13 21:16:43 +03:00
Jouni Malinen
1ff733383f Delay processing of EAPOL frames when not associated
If an EAPOL frame is received while wpa_supplicant thinks the driver is
not associated, queue the frame for processing at the moment when the
association event is received. This is a workaround to a race condition
in receiving data frames and management events from the kernel.

The pending EAPOL frame will not be processed unless an association
event is received within 100 msec for the same BSSID.
2009-09-04 18:04:41 +03:00
Dan Williams
cb8564b1dd dbus: add 'scanning' property
When the supplicant is connected and performs a scan, it doesn't enter
WPA_SCANNING state for various reasons.  However, external programs
still need to know that the supplicant is scanning since they may not
wish to perform certain operations during a scan (as those operations
will likely fail or yield incorrect results).  Add a 'scanning' property
and signal to the supplicant dbus interface to allow clients to
synchronize better with the supplicant when it scans.

Signed-off-by: Dan Williams <dcbw@redhat.com>
2009-05-27 21:06:40 +03:00
Jouni Malinen
6caf9ca68c Share same hw_feature definitions between hostapd and wpa_supplicant 2009-04-03 19:04:20 +03:00
Jouni Malinen
2d5b792d2b Add preliminary hostapd data structure initialization for AP mode
wpa_supplicant can now initialize hostapd data structures when mode=2 is
used to set up an AP. The hostapd configuration is not yet set based on
wpa_supplicant network configuration block. In addition, the glue code
for hostapd driver_ops needs number of functions that will be needed for
AP functionality.
2009-03-26 20:37:05 +02:00
Jouni Malinen
c2a0407851 Add SME support (separate authentication and association)
This can be used, e.g., with mac80211-based Linux drivers with
nl80211. This allows over-the-air FT protocol to be used (IEEE
802.11r).

Since the nl80211 interface needed for this is very recent (added
today  into wireless-testing.git), driver_nl80211.c has backwards
compatibility code that uses WEXT for association if the kernel does
not support the new commands. This compatibility code can be
disabled by defining NO_WEXT_COMPAT. That code will also be removed
at  some point to clean up driver_nl80211.c.
2009-03-20 22:26:41 +02:00
Jouni Malinen
4ef1e644eb Determiner whether driver is wired at runtime based on capabilities
Do not use just the driver name for this since driver_ndis.c supports
both wired and wireless NDIS drivers and needs to indicate the driver
type after initialization.
2009-03-07 22:05:43 +02:00
Sam Leffler
daa70d49de Add support for wpa_supplicant syslog output
Enable for build: CFLAGS += -DCONFIG_DEBUG_SYSLOG in .config
Enable at runtime: -s on command line
2009-03-02 21:40:44 +02:00
Jouni Malinen
ba2a573c5f Rename "broadcast SSID" to "wildcard SSID"
"Wildcard SSID" is the term used in IEEE Std 802.11-2007, so it is a
better name for the zero-length SSID used in Probe Request.
2009-02-14 22:21:17 +02:00
Jouni Malinen
fc2b7ed5f3 Add extended driver scan request command: driver_ops::scan2()
This can be used to provide support for scanning multiple SSIDs at a
time to optimize scan_ssid=1 operations. In addition, Probe Request IEs
will be available to scan2() (e.g., for WPS PBC scanning).
2009-02-14 17:01:32 +02:00
Jouni Malinen
80bc75f135 New driver capability info: max number of scan SSIDs
The driver wrappers can now inform wpa_supplicant how many SSIDs can
be used in a single scan request (i.e., send multiple Probe Requests
per channel). This value is not yet used, but it can eventually be used
to allow a new scan command to specify multiple SSIDs to speed up
scan_ssid=1 operations. In addition, a warning could be printed if
scan_ssid=1 is used with a driver that does not support it
(max_scan_ssids=0).
2009-02-12 22:05:32 +02:00
Jouni Malinen
a609915233 Allow WPS APs for PIN enrollment even without Selected Registrar
Some WPS APs do not set Selected Registrar attribute to 1 properly when
using an external Registrar. Allow such an AP to be selected for PIN
registration after couple of scan runs that do not find APs marked with
Selected Registrar = 1. This allows wpa_supplicant to iterate through
all APs that advertise WPS support without delaying connection with
implementations that set Selected Registrar = 1 properly.
2009-01-23 13:10:58 +02:00
Jouni Malinen
11ef8d3578 Added initial step for IBSS RSN support
This commit adds a new build option, CONFIG_IBSS_RSN=y, that can be used
to enable RSN support for IBSS. This links in RSN Authenticator code
from hostapd and adds code for managing per-peer information for IBSS. A
new wpa_cli command or driver event can be used to request RSN
authentication with an IBSS peer. New RSN Authenticator and Supplicant
will be allocated for each peer.

The basic state machine setup code is included in this commit, but the
state machines are not properly started yet. In addition, some of the
callback functions are not yet complete.
2009-01-15 01:21:55 +02:00
Jouni Malinen
7e5ba1b916 Mark functions static if not used elsewhere and use proper prototypes 2009-01-03 20:38:42 +02:00
Jouni Malinen
ac305589a3 Added support for global driver data (shared by multiple interfaces)
Driver wrappers can now register global_init() and global_deinit()
driver_ops handlers to get a global data structure that can be shared
for all interfaces. This allows driver wrappers to initialize some
functionality (e.g., interface monitoring) before any interfaces have
been initialized.
2008-12-22 22:24:31 +02:00
Luis R. Rodriguez
6d1584905c wpa_supplicant: Add support for setting of a regulatory domain
This adds support for setting of a regulatory domain to wpa_supplicant
drivers. It also adds regulatory domain setting for the nl80211 driver.
We expect an ISO / IEC 3166 alpha2 in the wpa configuration file as a
global.
2008-12-09 22:11:14 +02:00
Jouni Malinen
116654ce24 WPS: Moved wps_context initialization into wps_supplicant.c
The wps_context data is now managed at wpa_supplicant, not EAP-WSC. This
makes wpa_supplicant design for WPS match with hostapd one and also
makes it easier configure whatever parameters and callbacks are needed
for WPS.
2008-11-28 20:32:13 +02:00