When this test case is ran in remote test environment, there could be
additional APs in scan results after bssid_filter has been disabled.
That breaks the check on SCAN_RESULTS output. Extend this to cover the
remote testing case by using bssid_filter with both known APs listed
instead of full wildcard.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Instead of hardcoded bss-[1-6]*.conf files, generate them using the
correct BSSID for each AP device and send/install them on the remote
client as well if needed.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Generate ACL files instead of using files with hardcoded values for the
STA MAC addresses. Send the generated files also to the remote client if
required.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Some hostapd test cases use configuration files, e.g., ACLs in BSS
configuration. When executing remote tests (udp), we have to first send
these configuration files to the appropriate remote device. The new
send_file() helper can be used for that.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
We could have different ifconfig output formats on the remote devices,
so make the parser more flexible to handle such cases.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
This allows more test cases to be run in remote setup. Previously, we
used to block all test cases that required more than two arguments
(i.e., that needed the params argument).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
In case the hwsim wrapper is used in remote tests, show also which
device will be used as
apdev - hostapd
dev - wpa_supplicant
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Kill hostapd and wpa_supplicant based on the configuration parameters.
Previously, we could have killed wrong processes.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Hardcoded CONFIG_IEEE80211N to be included to clean up implementation.
More or less all new devices support IEEE 802.11n (HT) and there is not
much need for being able to remove that functionality from the build.
Included this unconditionally to get rid of one more build options and
to keep things simpler.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_open_sta_ps checks whether a STA told its hardware to enter power
save after enabling power save.
ap_open_ps_mc_buf checks whether an AP properly buffers and releases
multicast frames when a STA with PS active is associated.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
A test may want to check multicast connectivity independent of unicast
or check multicast without exercising unicast first. Factor out the
multicast connectivity check code into its own function.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Explicitly flush cfg80211 scan cache for this test case since the BSS
entry check might fail if there are multiple results for the same BSSID.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new dpp_alloc_auth() function addition changed function call
backtraces for memory allocation failure tests.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new dpp_gen_uri() helper function can be used to build the
bootstrapping URI from locally stored information. This can be used to
make it easier to update the URI, e.g., for NFC negotiated connection
handover cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
"finally" handler should not trigger a new exception when trying to
clear state for non-DPP builds. In addition, couple of checks for DPP
capability in the build were missing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a helper function for this and add checks for number of test cases
that were missing this. This gets rid of undesired FAIL results
(converts them to SKIP) for test runs where the station do not support
SAE.
Signed-off-by: Jouni Malinen <j@w1.fi>
Explicitly clear cfg80211 scan cache to avoid issues with old BSS
entries from previous test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
