Commit graph

463 commits

Author SHA1 Message Date
Jouni Malinen
bdf0518bb9 P2P: Direct P2P_CONNECT command to proper interface
It is possible for the P2P_CONNECT control interface command to be
issued on an incorrect interface. While the upper layer component should
really use global control interface for this, make this work by
redirecting the command to the correct context if needed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 11:54:39 +02:00
Jouni Malinen
9542f21f3a Clean up p2p_find command parsing and execution
There is no need to maintain three almost identical copies of the
wpas_p2p_find() call.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-28 21:58:38 +02:00
Daisuke Niwa
fa9f381f20 P2P: Allow a specific channel to be specified in P2P_FIND
The optional freq=<MHz> can now be used with the P2P_FIND command to
specify a single channel to scan during the first round of P2P search.
For example, this can be used to replace the full initial scan with a
single channel scan of a known operation channel.

Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
2015-02-28 21:52:56 +02:00
Jouni Malinen
1d747e2a98 Add snr and est_throughput to the BSS entries
These values were previously used only for sorting the scan results, but
it may be useful to provide access to the used values through the BSS
entries.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-22 11:09:54 +02:00
ASHUTOSH NARAYAN
5ce6ac11ab Inteworking: Add support to update the ANQP Capability List into the BSS
In addition, add support for returning the capability list through
the BSS control interface command.

Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
2015-02-21 16:07:53 +02:00
ASHUTOSH NARAYAN
185ada4770 HS 2.0: Add support to update the HS20 Capability List into the BSS
In addition, add support for returning the capability list through the
BSS control interface command.

Signed-off-by: ASHUTOSH NARAYAN <ashutoshx.narayan@intel.com>
2015-02-21 16:07:53 +02:00
Ola Olsson
10263dc2a4 Add control interface commands for fetching wpa_config values
The new "DUMP" and "SET <variable>" control interface commands can be
used to fetch global wpa_supplicant configuration parameters.

Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
2015-02-08 22:49:58 +02:00
Jouni Malinen
f91a512f1f Add INTERWORKING_ADD_NETWORK command
This can be used to provide more control to upper layers on network
blocks generated as part of Interworking network selection.
INTERWORKING_ADD_NETWORK behaves otherwise identically to
INTERWORKING_CONNECT, but it does not request a new connection after
having added the network block and it returns the network id of the
added network.

INTERWORKING_ADD_NETWORK followed by REASSOCIATE would behave more or
less identically to INTERWORKING_CONNECT, but this allows the created
network profile to be modified, if desired, and/or stored externally.
SELECT_NETWORK can also be used with the network id returned from
INTERWORKING_ADD_NETWORK to enforce that specific network profile to be
used for the next connection (though, it should be noted that this
behavior may not meet all Hotspot 2.0 requirements if there were other
enabled networks that could have higher priority).

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 22:49:58 +02:00
Jouni Malinen
5b74e086e6 P2P: Document P2P_CONNECT-auto
Commit b31be3a0fd ('P2P: Add automatic GO
Negotiation vs. join-a-group selection') added this P2P_CONNECT 'auto'
parameter, but did not update any documentation on it.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:50 +02:00
Jouni Malinen
99650cadc9 Add STOP_AP control interface command
This is mainly for testing purposes to allow beaconing to be stopped
without clearing AP state in hostapd.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:49 +02:00
Jouni Malinen
11e2ddbcd7 mesh: Remove duplicated no_auto_peer update
Commit 07cb45ccb2 ('mesh: Add no_auto_peer
config option') added a new struct wpa_ssid argument and added an
unnecessary parsing and setting of the value in
wpa_supplicant_ctrl_iface_update_network(). This is not needed since
wpa_config_set() takes care of parsing the parameters.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-07 16:19:53 +02:00
Jouni Malinen
1e529832a8 D-Bus: Fix network block type change
It is possible for a network profile to change its type from P2P
persistent group to a normal network and back. The D-Bus interface uses
different types of objects for those, so the object needs to
re-registered in case of type change. This fixes issues in leaving
behind an incorrect type of object and leaking memory when freeing such
a network block that has had its disabled parameter changed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-07 16:19:08 +02:00
Krishna Vamsi
87d5ef5a41 P2PS: Add commands to control interface redir list
This is needed to allow P2PS related new control interface commands to
be redirected for proper context processing.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
9a58e521ac P2PS: Callback to create pending group after sending PD Response
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
f309c18e50 P2PS: ASP provisioning commands to control interface
This adds new wpa_supplicant control interface commands
P2P_ASP_PROVISION and P2P_ASP_PROVISION_RESP.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
6d9085145c P2PS: Process P2PS provisioning commands
This extends wpas_p2p_prov_disc() implementation to accept P2PS
parameters. None of the callers are yet using this functionality; the
following commit introduces a user.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
5a4102ce0e P2PS: Add support to send ASP service requests
This extends the P2P_SERV_DISC_REQ control interface command with a new
"asp" service type. This takes service id, service string, and optional
service info as arguments.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:06 +02:00
Krishna Vamsi
ae9d45f329 P2PS: Extend add/del services logic to support ASP
In addition, add a new P2P_SERVICE_REP command that can be used to
replace existing ASP advertisements.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:06 +02:00
Brian Gix
4f88fc0464 P2PS: WPS changes needed for P2PS default PIN
This provides additional WPS definitions and rules for negotiating use
of P2PS default PIN configuration method.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-02 16:55:45 +02:00
Brian Gix
5177509657 P2PS: Add option to specify seek strings into P2P_FIND
P2PS seek strings can now be specified in the P2P_FIND control interface
command with one or more optional "seek=<str>" parameters.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-02 16:55:43 +02:00
Jouni Malinen
993a865407 Add eap_session_id to wpa_supplicant STATUS output
This makes the current EAP Session-Id available for external programs.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-28 13:09:31 +02:00
Jouni Malinen
399e61353a Add Suite B AKMs to key_mgmt capability list
Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 01:43:55 +02:00
Jouni Malinen
5e3b5197cc Add Suite B 192-bit AKM
WPA-EAP-SUITE-B-192 can now be used to select 192-bit level Suite B into
use as the key management method.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 01:43:52 +02:00
Jouni Malinen
b5f045deee Show supported group_mgmt capabilities
This extends GET_CAPABILITY command to allow the supported group
management frame cipher suites to be listed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-24 19:37:42 +02:00
Ilan Peer
7e608d1def P2P: Use the correct wpa_s interface to handle P2P state flush
A control interface call to flush the current state used the
current wpa_s to clear the P2P state even though it might not
be the interface controlling the P2P state.

Fix it by using the correct interface to flush the P2P state.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-01-20 01:57:59 +02:00
David Spinadel
8ad8bc5c36 NFC: Redirect NFC commands on global control interface
Redirect NFC commands from global control interface to P2P device
interface.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2015-01-20 01:57:59 +02:00
Matti Gottlieb
07565ab0f9 WNM: Fix the length of WNM_BSS_QUERY control interface command
The length should be 14 and not 10.
The current situation causes failure during parsing of the command.

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
2015-01-20 00:47:41 +02:00
Jouni Malinen
911942ee64 Add a test framework for various wpa_supplicant failure cases
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-19 19:34:00 +02:00
Jouni Malinen
6c69991382 Make wpa_supplicant FLUSH command more likely to clear all BSS entries
Move the wpa_bss_flush() call to the end of the function to allow any
pending user of a BSS entry to be cleared before removing the unused
entries. There were number of cases where BSS entries could have been
left in the list and this resulted in some hwsim test failures.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-17 15:39:48 +02:00
Jouni Malinen
783b2a977f Interworking: Fix INTERWORKING_CONNECT with zero-length SSID BSS entry
For Interworking connection to work, the SSID of the selected BSS needs
to be known to be able to associate with the AP. It was possible for the
scan results to include two BSS entries matching the BSSID when an
earlier scan with that AP has shown a hidden SSID configuration (e.g.,
when running hwsim test cases, but at least in theory, this could happen
with real use cases as well). When that happened, the incorrect BSS
entry may not have included RSN configuration and as such, it would get
rejected for Interworking connection.

Fix this by confirming that the selected BSS entry has a real SSID. If
not, try to find another BSS entry matching the same BSSID and use that,
if found with an SSID.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-15 12:24:18 +02:00
Jouni Malinen
cf08e9b1f4 Add MESH to modes capabilities
This makes it easier for upper layer programs to figure out whether the
wpa_supplicant and and the driver supports mesh.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-12 00:19:21 +02:00
Jouni Malinen
db5adfe777 Add SAE to auth_alg capabilities
This makes it easier for upper layer programs to figure out whether the
wpa_supplicant and and the driver supports SAE.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-12 00:19:21 +02:00
Jouni Malinen
a16514516b Add "GET tls_library" to provide information on TLS library and version
This new wpa_supplicant and hostapd control interface command can be
used to determine which TLS library is used in the build and what is the
version of that library.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-12 00:19:21 +02:00
Jouni Malinen
a156ffda61 Add support for testing memory allocation failures
The new control interface command TEST_ALLOC_FAIL and GET_ALLOC_FAIL can
now be used to trigger memory allocation failures for testing purposes.
TEST_ALLOC_FAIL sets a failure conditions with
<count>:func[;func][;func]... string and GET_ALLOC_FAIL returns the
current state using the same format. Whenever an allocation is made with
a matching backtrace of calling functions, the count is decremented by
one and once zero is reached, the allocation is forced to fail.

Function names can be prefixed with either '=' or '?' to get different
matching behavior. '=' requires this specific function to be the next
one in the backtrace (i.e., do not skip any other functions in the list
which is the default behavior). '?' allows the function to be optionally
present in the backtrace.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-07 13:19:43 +02:00
Ilan Peer
fb375883f4 ctrl_iface: Add MAC address randomization in scan processing
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-01-04 23:06:31 +02:00
Arik Nemtsov
6b90deae4d TDLS: Propagate enable/disable channel-switch commands to driver
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.

Allow enable/disable operations to be invoked via the control interface.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2015-01-04 20:30:11 +02:00
Jouni Malinen
b8db1dfc5c Clear next_scan_freqs on wpa_supplicant FLUSH command
It was possible for old scan state to remain from a previous test case
when an operation like WNM neighbor scan or another-BSS-in-ESS was
started, but stopped at the end of a test case. This could result in
failures, e.g., when running wnm_bss_tm_req followed by scan_setband.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-29 15:49:05 +02:00
Jouni Malinen
422ba11e30 Flush WPS registrar state on wpa_supplicant FLUSH command
This helps hwsim test cases by avoiding undesired state from previously
executed test cases affecting following tests.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-21 17:47:42 +02:00
Jouni Malinen
209702d4c9 Add possibility to set the setband parameter
Commit faf9a8585d added mechanism for
selecting 2.4 or 5 GHz band for scan operation. However, no mechanism
for setting the setband value was added at that time. This commit adds a
new SET ctrl_iface parameter to allow the setband functionality to be
used. "SET setband <AUTO/5G/2G>" can be used to select all bands, 5 GHz
band only, or 2.4 GHz band only.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-19 22:56:41 +02:00
Jouni Malinen
e69ae5ff31 Reject new SCAN commands if there is a pending request
FAIL-BUSY was already returned for the case where a scan had been
started, but with the radio work design, it would have been possible to
schedule multiple scan requests if a non-scan radio work was in
progress. Multiple back-to-back scans are not usually very helpful, so
reject this type of cases where the SCAN command would be used to build
such a sequence.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-19 15:14:38 +02:00
Masashi Honma
5b78493f3b mesh: Add mesh interface creation command for mesh gate
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.

This command makes a virtual mesh interface to be used for mesh gate.

This command expects to be used like this.

wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-14 23:27:43 +02:00
Jouni Malinen
f77cedc11a WPS ER: Remove unnecessary return value
wps_er_deinit() cannot fail and it does not return anything, so neither
should wpas_wps_er_stop().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 02:28:03 +02:00
Jouni Malinen
5407c69d15 Remove unnecessary STA_AUTOCONNECT handler function
This function could not fail and it can be replaced with a single
line variable update that takes less code than the function call.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:27:41 +02:00
Jouni Malinen
a1144000cd Remove unnecessary return value
wpa_bss_flush*() cannot fail and as such, there is no need for
wpa_supplicant_ctrl_iface_bss_flush() to return a value either.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:22:23 +02:00
Jouni Malinen
5ac73acf12 Simplify eapol_sm_get_mib() result handling
This function cannot return negative value, so no need to check for
that. If there is not enough room in the buffer or if something
unexpected happens, 0 is returned.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:15:38 +02:00
Jouni Malinen
43a66ecba3 Fix SCAN control interface command error cases
Update the scan parameters in wpa_s only in case the scan command is
going to be executed. In other words, do not change the parameters for
an ongoing scan (the SCAN command is rejected with FAIL-BUSY) or if any
of the parameters is invalid.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-12 01:12:15 +02:00
Jouni Malinen
b68d602dc4 Fix ANQP_GET/HS20_GET_ANQP parsing to skip space after address
The space following the BSSID was not skipped properly if the following
parameter started with the "hs20:" prefix. For other cases, atoi() ended
up ignoring the space, but it is cleaner to skip it anyway for all
cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-11 15:18:11 +02:00
Jouni Malinen
97cfe110dc Clear wpa_s->disconnected on ctrl_iface FLUSH
This is needed to get into more consistent state after the FLUSH
command. DISCONNECT followed by FLUSH could result in
wpa_s->disconnected being left to 1 and this resulted in a test failure,
e.g., when running wpas_ctrl_dup_network followed by
wpas_ctrl_enable_disable_network where the latter was expecting
ENABLE_NETWORK on a disabled network to connect automatically and that
does not happen if wpa_s->disconnected == 1.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-08 16:22:13 +02:00
Jouni Malinen
aaadd72733 Check os_snprintf() result more consistently - more checks
Add more os_snprintf() result validation checks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
1d39977136 Check os_snprintf() result more consistently
While these are using practically large enoungh buffer sizes, it is
better to be more consistent with checking os_snprintf() return value.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00