Add an optional CPT parameter to asp_provision() method of
WpaSupplicant.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Add asp_provision method which issues either P2PS PD Request or, if the
status is provided, continues the deferred flow by sending follow on
PD Request.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Commit 53606b105c ('tests: Wait for scan
to complete on all interfaces in reset()') added option of passing
ifname to get_driver_status(). This could result in FAIL-NO-IFNAME-MATCH
returns that get printed out in "Ignore unexpected status-driver line"
messages if the interface is not found. Check for this case to avoid
that unnecessary print.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When WpaSupplicant executes reset() it waits until all the ongoing scans
are completed. However, it checks the status of the wlanX interface
only. If a dedicated P2P device interface is used, scan may be still
running on the P2P Device interface, e.g., due to P2P_FIND. This might
affect subsequent tests.
Fix this by waiting until the scan is done both on wlanX and P2P
Device interfaces.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Change the reset() method to use the global control interface
for resetting P2P state and also add a call to P2P_FLUSH.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
There seem to be cases where flush_scan_cache() was unable to clear all
BSS entries due to a hidden SSID BSS (SSID length 0) showing up again
from cfg80211 BSS table. Check for this and run the flush operation
again if any entries remain.
This fixes an issue where the following hwsim test case sequence
resulted in the last test case failing due to the old BSS entry from the
first test case being in place and showing unexpected flags information:
ap_hs20_min_bandwidth_home_hidden_ssid_in_scan_res
ap_hs20_remediation_required
ap_mixed_security
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
list_networks() always used the wlanX control interface to query for the
current list of networks. However, when a dedicated P2P Device is used,
the global control interface should be used when checking persistent
group network profiles.
Fix this by adding an optional parameter indicating that the P2P
networks are requested, and in such a case use the global control
interface.
In addition update test_p2p_persistent to use the argument when needed.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
When resetting a device, remove all the P2P networks to prevent
unexpected behavior in following tests. This is needed for the case
where P2P Device interface is used.
Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
It is possible for a low powered CPU to take excessively long time to
delete 1000 network blocks when running under valgrind. This would have
resulted in the test case failing and the following reset operation
timing out which would then stop the test sequence completely.
Signed-off-by: Jouni Malinen <j@w1.fi>
1. Add get_group_ifname() to wpasupplicant.py
2. Use the function to get the interface name for the bridge.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
run-tests.py is running as root, so sudo does not need to be used
anymore from within each test case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed for cases that the group interface differs from the main
interface, i.e., when a dedicated P2P Device interface is used.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
This verifies that PBC session overlap detection does not get indicated
when forming the group with the same peer multiple times.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There were couple of common cases where the control interface for the
dynamic wpa_supplicant instance could have been left in attached state
until Python ends up cleaning up the instance. This could result in
issues if many monitor interface events were queued for that attached
socket. Make this less likely to cause issues by explicitly detaching
and closing control interfaces before moving to the next test case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Make sure the wmm_ac_status command reflects correctly the existing
tspecs after add_ts/del_ts commands. Add a new test to verify all tspecs
are removed on roaming (while FT is not used).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
It is possible for WpaSupplicant instance to be used without the global
control socket, so allow dump_monitor() to handle this case cleanly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for BSS entries on the scanned channel (2412 MHz) to be
left behind after flush_scan_cache() call. Use a less likely channel
2417 MHz as the default channel to scan. This will hopefully get rid of
most problematic BSS entries from previous test cases. For example,
ap_hs20_oen followed by ap_hs20_random_mac could fail due to
INTERWORKING_CONNECT seeing non-RSN scan result from the previous test
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by clearing
the default PMF behavior change only in case it was actually modified
during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by stopping ER
only in case it was actually used during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
This tests RP EAP-Initiate/Re-auth-Start transmission, ERP key
derivation, and EAP-Initiate/Re-auth + EAP-Finish/Re-auth exchange and
rMSK derivation.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more convenient and consistent to clear the cached scan
results from cfg80211 and wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Keep full channel scans in autogo for test coverage, but use single
channel scan in all other autogo* test cases to remove unnecessary
waiting that does not add any test coverage. This removes more than one
minute from the total test execution time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There are valid status (and possibly status-driver) responses
that don't have a name=value format, ignore those in the test
framework parser.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
