Commit graph

659 commits

Author SHA1 Message Date
Jouni Malinen
bb337ddac2 DFS: Do not use cf1 to override freq for 20 MHz channels
NL80211_ATTR_CENTER_FREQ1 is defined to be used for anything but 20 MHz
bandwidth, so it could be unset for 20 MHz channels. Do not use it to
override center frequency from NL80211_ATTR_WIPHY_FREQ (if available)
for 20 MHz channels to avoid clearing frequency.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 21:50:48 +02:00
Jouni Malinen
0dfd2c61a5 Document AP mode startup functions
This provides some more details on how interfaces and BSSes are
initialized during hostapd startup.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 21:30:31 +02:00
Jouni Malinen
fee947bfc0 hostapd: Use correct wpa_printf verbosity level for message
This configuration file message is informative and MSG_INFO should be
used instead of MSG_ERROR.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 20:12:36 +02:00
Jouni Malinen
e4ba031531 hostapd: Use start_ctrl_iface() from hostapd_add_iface()
Better share the same function for initializing control interface from
the two possible paths that can add a new interface to hostapd.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
bf7f09bd24 Fix AP mode QoS Map configuration to be per-BSS
This is a per-BSS configuration parameter and as such, needs to be
configured to the driver from hostapd_setup_bss() instead of
hostapd_driver_init().

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
dc036d9ee0 DFS: Convert hostapd_data use to hostapd_iface
DFS operations are specific to the interface (radio/wiphy), not BSS
(netdev/vif), so hostapd_iface is the appropriate element to use in
them.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
2db938e8de hostapd: Fill in phyname automatically
If per-BSS configuration enabling did not provide a phy name, iface->phy
was left empty. It can be helpful to set this up automatically, so fill
that when initializing the interface.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
5ae6449ca2 hostapd: Add ctrl_iface STATUS command
This can be used to fetch runtime information about hostapd interfaces.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
afadaff976 Optimize 40 MHz HT co-ex scan on AP
Only scan the affected channels instead of all enabled channels when
determining whether the primary and secondary channel for HT40 needs to
be swapped. This speed up HT40 setup considerably on 5 GHz band.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
7d6d73701e hostapd: Add AP-ENABLED/DISABLED ctrl_iface events
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
e1c5faf007 hostapd: Track interface state
The new hostapd_iface::state enum is used to track the current state of
the hostapd interface (a radio/wiphy).

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
f0793bf191 hostapd: Wait for channel list update after country code change
If hostapd is requested to set the country code and the previous country
code differs from the new one, the channel list information from the
driver may change. This change may not be instant, so wait for an
EVENT_CHANNEL_LIST_CHANGED event before continuing interface setup with
fetching of the channel list information. This fixes issues where the
selected channel is not available based on the previous regulatory data
and update through CRDA takes some time.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
ae134e1d2b hostapd: Add ctrl_iface events for ACS
These give status information to external observers from automatic
channel selection operations.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
ad08e1413b hostapd: Move ctrl_iface initialization to happen earlier
Channel determination may take considerable time when ACS or DFS is
used, so it is useful to be able to observe this process through the
control interface. Move the initialization of the control interfaces to
happen before channel determination so that this can be achieved.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
4a5deb9b9d hostapd: Simplify interface initialization
Use hostapd_interface_init2() for all interfaces instead of the
previously used different paths for per-interface-config and
per-BSS-config cases. This moves the calls to hostapd_driver_init() and
hostapd_setup_interface() to happen after all configuration files have
been read.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 19:51:06 +02:00
Jouni Malinen
186c905912 DFS: Add control interface events for various DFS events
These can be useful for external programs that track the current state
of the AP.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 11:31:48 +02:00
Jouni Malinen
71cdf6b624 hostapd: Fix ENABLE failure to not remove interface
Previously, ENABLE command ended up freeing the hostapd_iface context on
initialization failures, but did not even remove the interface from the
list of available interfaces. This resulted in use of freed memory with
any following operation on the same interface. In addition, removing the
interface on initialization failure does not seem like the best
approach. Fix both of these issues by leaving the interface instance in
memory, but in disabled state so that the configuration can be fixed and
ENABLE used again to enable the interface or REMOVE used to remove the
interface.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-03 11:31:48 +02:00
Jouni Malinen
61323e70e1 Convert perror/printf calls to wpa_printf
This makes debug and error logging more consistent and allows them to be
directed to a file more easily.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-02 12:58:33 +02:00
Jouni Malinen
2aec4f3c0c Allow add-BSS operation to re-use existing netdev
When removing and re-adding the first wlan# netdev to hostapd
dynamically, the netdev is already present and should not be removed and
re-added to maintain its state as not-added-by-hostapd so that it does
not get removed automatically.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:34:25 +02:00
Jouni Malinen
5592065850 hostapd: Allow a single BSS to be removed from an interface
The global control interface command "REMOVE <ifname>" can now be used
to remove a single virtual interface (BSS) without affecting other
virtual interfaces on the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:30:15 +02:00
Kyeyoon Park
2e2fff37e9 hostapd: Allow a single BSS to be added to an interface
The global control interface command "ADD
bss_config=<phyname>:<config file>" can now be used to add a single
virtual interface (BSS) to an interface.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:30:15 +02:00
Kyeyoon Park
a1fb5692af hostapd: Make hostapd_interface_init_bss() available externally
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:00:31 +02:00
Kyeyoon Park
66936c6af8 hostapd: Make hostapd_init() available externally
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:00:31 +02:00
Kyeyoon Park
390e489c0d hostapd: Allow the first BSS in a multi-BSS setup to be removed
This moves the vif added check from core hostapd to the driver wrapper
(only driver_nl80211.c uses this) and reorders operations a bit to allow
the first BSS (vif) to be removed from a multi-BSS setup.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 22:00:31 +02:00
Kyeyoon Park
33b0b330ce hostapd: Fix error path in hostapd_add_iface()
Incorrect count variable was used in freeing up the BSS data.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-31 15:59:12 +02:00
Helmut Schaa
770ecdf27c ACS: Do not get stuck while failing to do a subsequent scan
Return control flow to hostapd by calling hostapd_acs_completed()
if requesting a scan from the underlying device fails.

Signed-hostapd: Helmut Schaa <helmut.schaa@googlemail.com>
2013-10-31 15:12:21 +02:00
Michal Kazior
813d4bac5a DFS: Add support for multi-BSS
If radar was detected single BSS is notified about it. This caused only
that single BSS to be stopped and restarted. However, due to nl80211
interface combinations the BSS was not started on a new channel and
other BSSes remained operating on the old channel.

The downside is that hostapd_disable_iface() causes deauth frames to be
sent. This is undesired but on the other hand it doesn't make sense to
create workarounds that imitate CSA's 'block tx'. For proper Tx
quiescing CSA should be properly implemented.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
2013-10-31 15:12:17 +02:00
Michal Kazior
954e71d270 DFS: Reset cac_started properly
If CAC was stopped but hostapd was not terminated cac_started would
remain set to 1.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
2013-10-31 14:49:38 +02:00
Michal Kazior
6a398ddc9a DFS: Sanitize channel availability checks
Fixes corner case of holes in channel list and simplifies availability
checks.

Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
2013-10-31 14:49:06 +02:00
Michal Kazior
32595da608 DFS: Fix HT40/VHT calculation
Decouple HT/VHT offset/center-freq calculations from channel lookup.
This will be necessary for further improvements on the DFS codebase.

Signed-hostap: Michal Kazior <michal.kazior@tieto.com>
2013-10-31 14:49:03 +02:00
Jouni Malinen
6f2db2fbdd hostapd: Validate configuration parameters on RELOAD command
Reject RELOAD control interface command if the dynamic configuration
changes have resulted into a state where the configuration is invalid.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:58:21 +02:00
Jouni Malinen
eff0fd1ee8 hostapd: Move generic configuration functions into src/ap
This allows the configuration validation routines to be called from
src/ap/*.c for runtime updates of configuration without reprocessing the
full configuration file.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:58:21 +02:00
Jouni Malinen
5afaa067d9 hostapd: Allow per-BSS (vif) configuration files
This provides a new option for configuring multiple virtual interfaces
(BSS) that share a single radio. The new command line parameter
-b<phyname>:<config file name> is used to define one or more virtual
interfaces for each PHY. The first such entry for a new PHY is used to
initialize the interface structure and all consecutive parameters that
have the same PHY name will be added as virtual BSS entries to that
interface. The radio parameters in the configuration files have to be
identical.

This can be used as an alternative for the bss=<ifname> separator and
multiple BSSes in a single configuration file design while still
allowing hostapd to control the PHY (struct hostapd_iface) as a group of
virtual interfaces (struct hostapd_data) so that common radio operations
like OLBC detection and HT40 co-ex scans can be done only once per real
radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:58:21 +02:00
Jouni Malinen
ebd79f07c4 hostapd: Make hostapd_config::bss array of pointers
This makes it more convenient to move BSS configuration entries between
struct hostapd_config instances to clean up per-BSS configuration file
design.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:58:21 +02:00
Jouni Malinen
a781e211f9 hostapd: Force PSK to be derived again on BSS reload
This may be needed if the wpa_psk information for previously derived
from passphrase and either the SSID or the passphrase has changed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:58:20 +02:00
Jouni Malinen
9f104b0324 hostapd: Reuse hostapd_clear_old() for RELOAD command
Instead of duplicating the functionality and missing changes (like the
hostapd_broadcast_wep_clear() call), use the hostapd_clear_old()
function that was already used for the similar case with configuration
file reload.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-29 16:09:34 +02:00
Eliad Peller
6b02335a96 hostapd: Mask out not-supported VHT capabilities
Mask the remote VHT capabilities with our own capabilities, similarly
to what is done for HT capabilities.

Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
2013-10-27 19:28:40 +02:00
Eliad Peller
7f0303d5b0 hostapd: Verify VHT 160/80+80 MHz driver support
Make sure the driver supports 160/80+80 MHz VHT capabilities
before trying to configure these channels.

Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
2013-10-27 19:17:23 +02:00
Eliad Peller
c781eb8428 hostapd: Verify VHT capabilities are supported by driver
Make sure the defined VHT capabilities are supported by the driver.

Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
2013-10-27 19:11:29 +02:00
Jouni Malinen
e7ecab4a3b Use ARRAY_SIZE() macro
Replace the common sizeof(a)/sizeof(a[0]) constructions with a more
readable version.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-26 17:49:05 +03:00
Janusz Dziedzic
2e946249b1 DFS: Handle radar event when CAC actived correctly
When we have CAC active and receive a radar event, we should ignore
CAC_ABORT event and handle channel switch in the radar event handler.

Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2013-10-26 17:48:55 +03:00
Janusz Dziedzic
5eaf240af5 DFS: Fix overlapped() function to check only DFS channels
This fixes a problem when operating on non-DFS channel and receiving a
radar event for that channel. Previously, we would have decided to
switch channels.

Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2013-10-26 17:48:46 +03:00
Janusz Dziedzic
345276a6b5 DFS: Adjust center freq correctly for VHT20/VHT40
Setup correct seg0 for VHT with 20/40 MHz width (VHT_CHANWIDTH_USE_HT).

Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2013-10-26 17:48:41 +03:00
Janusz Dziedzic
1dc17db34a DFS: Fix available channels list for VHT80
Add a table of available VHT80 channels. This table contains the first
available channel. We will also choose this first channel as the control
one.

Signed-hostap: Janusz Dziedzic <janusz.dziedzic@tieto.com>
2013-10-26 17:48:36 +03:00
Jouni Malinen
03610ad28d Clean up get_seqnum() use for IPN
Some driver wrappers may implement this by writing eight octets even
though IPN is only six octets. Use a separate WPA_KEY_RSC_LEN (8) octet
buffer in the call to make sure there is enough buffer room available
for the full returned value and then copy it to IPN field.

The previous implementation used the following igtk field as the extra
buffer and then initialized that field afterwards, so this change does
not fix any real issue in behavior, but it is cleaner to use an explicit
buffer of the maximum length for get_seqnum().

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-26 15:56:07 +03:00
Jouni Malinen
35f836375d DFS: Add forgotten break statement
The VHT_CHANWIDTH_160MHZ case fell through to the default case and
printed out a debug message that was not supposed to be shown here.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-26 15:55:09 +03:00
Helmut Schaa
677cf19091 hostapd: Select any supported channel if ACS fails
Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
2013-10-23 00:44:48 +03:00
Helmut Schaa
20f9cb1842 hostapd: Allow ACS to deal with partial survey data
Previously ACS required valid survey data on all available channels.
This can however not be guaranteed. Instead of just failing, fall back
to the subset of channels that have valid ACS data.

Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
2013-10-23 00:44:41 +03:00
Helmut Schaa
3645fd5aae hostapd: Propagate ACS errors to iface setup
Otherwise hostapd might hang doing nothing anymore. Propagate ACS
errors so we can fail gracefully.

Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
2013-10-23 00:44:36 +03:00
Helmut Schaa
0e1d0b370f hostapd: Don't get stuck after failed ACS
If ACS fails we still need to call hostapd_setup_interface_complete.
Otherwise hostapd will just hang doing nothing anymore. However, pass
an error to hostapd_setup_interface_complete to allow a graceful fail.

Signed-hostap: Helmut Schaa <helmut.schaa@googlemail.com>
2013-10-23 00:44:30 +03:00