This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new "timeout" argument to the event message if the nl80211 message
indicates that the connection failure is not due to an explicit AP
rejection message. This makes it easier for external programs to figure
out why the connection failed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the simplest case of SAE group negotiation to occur by
selecting the next available group if the peer STA indicates the
previous one was not supported. This is not yet sufficient to cover all
cases, e.g., when both STAs need to change their groups, but at least
some cases are no covered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_deinit() got called twice if the random_get_bytes() fails to
generate the MGTK. This resulted in double-freeing the rsn->auth
pointer. Fix this by allowing mesh_rsn_auth_init() handle freeing for
all error cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Start using the wpa_supplicant remote UDP interface for the control and
monitor sockets for P2P group interfaces so that P2P tests would work on
real hardware. Also have the group requests and events show in the test
log with the hostname and the interface name of the group interface.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
This adds an extra parameter in GroupStarted signal to indicate whether
the created group is Persistent or not. It is similar to the
[PERSISTENT] tag which comes in P2P-GROUP-STARTED over the control
interface.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
hostapd deinit functions were not ready to handle a case where the data
structures were not fully initialized. Make these more robust to allow
wpa_supplicant mesh implementation to use the current deinit design in
OOM error cases without causing NULL pointer dereferences.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of reporting the memory allocation failure and stopping, run the
scan even if the frequency list cannot be created due to allocation
failure. This allows the wpa_s->reattach flag to be cleared and the scan
to be completed even if it takes a bit longer time due to all channels
getting scanned.
Signed-off-by: Jouni Malinen <j@w1.fi>
The code contained some places that used an additional argument for
setup_hw after -R and also contained places where setup_hw cmdline was
passed as a string instead of an argument list. It also contained places
where the ifname was only treated as a single interface and disregarded
the possiblity of multiple interfaces. This commit fixes these issues
and executes setup_hw from a single function for all cases.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Use a monitor interface given in the command line that is not also a
station or an AP as a monitor running wlantest on the channel used by
the test. This makes all the tests that use wlantest available for
execution on real hardware on remote hosts.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
In monitor.py in the remote tests code there is fucntion create() that
creates standalone monitor interfaces. In this function there is an
iteration of the ifaces of the host by using the ifaces variable but
this variable is non-existing. This patch creates this variable before
its usage.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
In wpaspy.py in the Ctrl object constructor there is a try/except. In
the except part the code references the s attribute of the object. This
attribute is only created later in the try part. If an exception occurs
before the attribute creation then the except part references a non
existing attribute. Fix that by assigning None to the s attribute at the
beginning of the try part.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
This function is used for remote tests when a monitor interface is
needed on the channel on which the AP operates. This change enables us
to also query P2P interfaces for the channel information to use for
monitor interfaces.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
Instead of accessing the logs list member of the remote host directly,
use a function to add logs to the remote host to be collected after the
test. This enables us to later have different implementation of remote
hosts or logs collection without requiring to have this list as the
implementation.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
The regular hwsim tests use both unicast and broadcast frames to test
the connectivity between 2 interfaces. For real hardware (remote hwsim
tests) the broadcast frames will sometimes not be seen by all connected
stations since they can be in low power mode during DTIM or because
broadcast frames are not ACKed. Use 10 retries for broadcast
connectivity tests for real hardware so that the test will pass if we
successfully received at least one of them.
Signed-off-by: Jonathan Afek <jonathanx.afek@intel.com>
This avoids internal access of structs and also removes the dependency
on the reimplemented TLS PRF functions when EAP-FAST support is not
enabled. Notably, BoringSSL doesn't support EAP-FAST, so there is no
need to access its internals with openssl_get_keyblock_size().
Signed-Off-By: David Benjamin <davidben@google.com>
This is needed to work with the tls_openssl.c changes that renamed the
function that is used for deriving the EAP-FAST keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Most protocols extracting keys from TLS use RFC 5705 exporters which is
commonly implemented in TLS libraries. This is the mechanism used by
EAP-TLS. (EAP-TLS actually predates RFC 5705, but RFC 5705 was defined
to be compatible with it.)
EAP-FAST, however, uses a legacy mechanism. It reuses the TLS internal
key block derivation and derives key material after the key block. This
is uncommon and a misuse of TLS internals, so not all TLS libraries
support this. Instead, we reimplement the PRF for the OpenSSL backend
and don't support it at all in the GnuTLS one.
Since these two are very different operations, split
tls_connection_prf() in two. tls_connection_export_key() implements the
standard RFC 5705 mechanism that we expect most TLS libraries to
support. tls_connection_get_eap_fast_key() implements the
EAP-FAST-specific legacy mechanism which may not be implemented on all
backends but is only used by EAP-FAST.
Signed-Off-By: David Benjamin <davidben@google.com>
Commit 68ae4773a4 ('OpenSSL: Use library
wrapper functions to access cert store') fixed most of these, but missed
a few.
Signed-Off-By: David Benjamin <davidben@google.com>
If preassoc_mac_addr is used and updating the MAC address fails in
wpas_trigger_scan_cb(), the cloned scan parameters were leaked. Fix that
and also send a CTRL-EVENT-SCAN-FAILED event in this and another error
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to have a separate if statement to skip the cases where
phase1 is not set. Just check it with the strstr comparison since this
case is not really used in practice.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_s->current_ssid is set to a non-NULL ssid pointer value here, so
there is no need for the extra if statement.
Signed-off-by: Jouni Malinen <j@w1.fi>
The P2P Device interface can only send Public Action frames. Non-Public
Action frames must be sent over a group interface. The previous
implementation sometimes tried to send non-Public Action frames such as
GO Discoverability over the P2P Device interface, however, the source
address of the frame was set to the group interface address so the code
in offchannel.c knew to select the correct interface for the TX.
The check breaks when the P2P Device and group interfaces have the same
MAC address. In this case the frame will be sent over the P2P Device
interface and the send will fail.
Fix this problem in two places:
1. In offchannel, route non-Public Action frames to the GO
interface when the above conditions are met.
2. When a TX_STATUS event arrives on such routed frame, it will
arrive on the GO interface but it must be handled by the P2P Device
interface since it has the relevant state logic.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
This makes changes such that hostapd (and wpa_supplicant AP mode)
registers to kernel for specific Action frames instead of generically
registering for all Action frames. This makes it easier for other
programs to register for some Action frames that hostapd does not handle
today without having to somehow coordinate directly with hostapd.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows using P2PS config method with or without PIN for connection.
wpa_supplicant should internally handle the default PIN "12345670" and
shall also allow connection irrespective of PIN used in P2P_CONNECT.
For example,
1. P2P_CONNECT 02:2a:fb:22:22:33 p2ps
2. P2P_CONNECT 02:2a:fb:22:22:33 xxxxxxxx p2ps
Where the second one is maintained for backwards compatibility.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add P2PS config flag only when config_methods are set. This restores the
pre-P2PS behavioer for the cases where Display or Keypad config method
is specified for a peer (i.e., do not add the new P2PS method in that
case).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This gets rid of a valgrind warning on uninitialized memory read in the
eap_proto_sake_errors test case where the result was used after the
failed eap_sake_compute_mic() call.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
