The OEM data binary blobs from application/service will be routed to the
appropriate device based on this attribute value. This optional
attribute is used to specify whether the device type is virtual or
physical. This attribute can be omitted when the command is for a
virtual device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Some chipsets don't have the capability to run agile spectral scan with
160/80+80 MHz modes. Add separate agile spectral scanning capability
flags for 160, 80+80, and non-160 MHz modes to cover such cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
In the SME-in-driver case, wpa_supplicant used only the selected SAE
auth_alg value as the trigger for enabling external authentication
support for SAE. This prevented the driver from falling back to full SAE
authentication if PMKSA caching was attempted (Open auth_alg selected)
and the cached PMKID had been dropped.
Enable external auth based on SAE/FT-SAE key_mgmt, rather than doing
this based on SAE auth_alg, so that the driver can go through full SAE
authentication in cases where PMKSA caching is attempted and it fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When operating on the 6 GHz band, add 6 GHz Operation Information inside
the HE Operation element and don't publish HT/VHT IEs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Replace HOSTAPD_MODE_IEEE80211AX mode checks with is_6ghz_op_class()
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Add support for new hardware mode for 6 GHz band. 6 GHz operation is
defined in IEEE P802.11ax/D4.3. 6 GHz band adds global operating classes
131-135 that define channels in frequency range from 5940 MHz to 7105
MHz.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Remove HOSTAPD_MODE_IEEE80211AX mode
- Replace check for HOSTAPD_MODE_IEEE80211AX with is_6ghz_freq()
- Move center_idx_to_bw_6ghz() to ieee802_11_common.c file
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
If the AP advertises RSN Extension element, it has to be advertised
consistently in the unprotected (Beacon and Probe Response) and
protected (EAPOL-Key msg 3/4) frames. Verify that this is the case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If hostapd is configured to enable only the hash-to-element version of
SAE PWE derivation (sae_pwe=1), advertise BSS membership selector to
indicate this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This parameter can be used to specify which PWE derivation mechanism(s)
is enabled. This commit is only introducing the new parameter; actual
use of it will be address in separate commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These are the defined values/identifiers for SAE hash-to-element
mechanism from IEEE P802.11-REVmd/D3.0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The initial crypto wrapper implementation for wolfSSL seems to have
included a copy-paste error in crypto_bignum_sub() implementation that
was identical to crypto_bignum_add() while mp_sub() should have been
used instead of mp_add().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The logic for displaying the message about no configuration being
available for the Enrollee was reversed when support for multiple Config
Objects was added. This was supposed to be shown only if the first
Config Object fails (i.e., when no configuration is available); not when
second attempt fails (since the first one had already been successful in
that case).
Fixes: 7eb06a3369 ("DPP2: Allow multiple Config Objects to be build on Configurator")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd is by default waiting STA to send SAE Confirm before sending the
SAE Confirm. This can now be configured with sae_confirm_immediate=1
resulting in hostapd sending out SAE Confirm immediately after sending
SAE Commit.
These are the two different message sequences:
sae_confirm_immediate=0
STA->AP: SAE Commit
AP->STA: SAE Commit
STA->AP: SAE Confirm
AP->STA: SAE Confirm
STA->AP: Association Request
AP->STA: Association Response
sae_confirm_immediate=1
STA->AP: SAE Commit
AP->STA: SAE Commit
AP->STA: SAE Confirm
STA->AP: SAE Confirm
STA->AP: Association Request
AP->STA: Association Response
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add two new configuration parameters for hostapd:
enable_edmg: Enable EDMG capability for AP mode in the 60 GHz band
edmg_channel: Configure channel bonding for AP mode in the 60 GHz band
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
IEEE P802.11ay defines Enhanced Directional Multi-Gigabit (EDMG) STA and
AP which allow channel bonding of 2 channels and more.
nl80211 provides the driver's EDMG capabilities from the kernel
using two new attributes:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represents the channel bandwidth
configurations supported by the driver.
The driver's EDMG capabilities are stored inside struct hostapd_hw_modes.
As part of the connect request and starting AP, EDMG parameters are
passed as part of struct hostapd_freq_params.
The EDMG parameters are sent to the kernel by using two new attributes:
NL80211_ATTR_WIPHY_EDMG_CHANNEL and NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
which specify channel and bandwidth configuration for the driver to use.
This implementation is limited to CB2 (channel bonding of 2 channels)
and the bonded channels must be adjacent.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
The new use_akm_selector=1 value to Configurator parameters can now be
used to request a list of AKM suite selectors to be used in the
Configuration Object if the Enrollee supports version 2 or newer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Process all received DPP Configuration Object attributes from
Configuration Result in Enrollee STA case. If wpa_supplicant is
configured to add networks automatically, this results in one network
being added for each included Configuration Object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Special @CONF-OBJ-SEP@ string can now be used as a DPP configuration
string value to split the string into two different components to
configure two Config Objects for an Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit e820cf952f ("MFP: Add MFPR flag into station RSN IE if 802.11w
is mandatory") added indication of MFPR flag in non-FT cases and was
further extended to cover FT protocol in commit ded56f2faf ("FT: Fix
MFPR flag in RSNE during FT protocol"). Similar fix is needed for
FILS+FT as well.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows Data frames to be fully processed for the case where VLAN
tags are used on the wireless link.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Linux 2.6.32 (December 2009) introduced alternate netlink messages
for setting and installing keys, deprecating the older ones.
To allow hostapd/wpa_supplicant to use new features only provided via
the new API this patch migrates all netlink messages to the current ones.
Since the nl80211 driver was sometimes already using the new format this
is only unifying the netlink API usage and not changing the minimal
kernel requirement.
The following netlink attributes have been retired for key installs:
NL80211_ATTR_KEY_DATA
NL80211_ATTR_KEY_TYPE
NL80211_ATTR_KEY_SEQ
NL80211_ATTR_KEY_IDX
NL80211_ATTR_KEY_CIPHER
NL80211_ATTR_KEY_DEFAULT
NL80211_ATTR_KEY_DEFAULT_MGMT
NL80211_ATTR_KEY_DEFAULT_TYPES
And replaced by the following attributes nested in NL80211_ATTR_KEY:
NL80211_KEY_DATA
NL80211_KEY_TYPE
NL80211_KEY_SEQ
NL80211_KEY_IDX
NL80211_KEY_CIPHER
NL80211_KEY_DEFAULT
NL80211_KEY_DEFAULT_MGMT
NL80211_KEY_DEFAULT_TYPES
When getting Michael MIC failure notifications or querying a key
sequence number the kernel continues to use the old attributes:
NL80211_ATTR_KEY_TYPE
NL80211_ATTR_KEY_SEQ
NL80211_ATTR_KEY_IDX
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
PTKINITNEGOTIATING in the WPA state machine calls wpa_send_eapol() and
hands over the GTK instead of the PTK keyid.
Besides a confusing debug message this does not have any negative side
effects: The variable is only set to a wrong value when using WPA2 but
then it's not used.
With this patch PTKINITNEGOTIATING sets the PTK keyid unconditionally to
zero for EAPOL-Key msg 3/4 and differentiates more obviously between GTK
and PTK keyids.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
hostapd is only interested in RTM_IEEE80211.
wpa_supplicant is only interested in RTM_IEEE80211, RTM_IFINFO and
RTM_IFANNOUNCE.
This supports the NetBSD RO_MSGFILTER interface and the alternative
DragonFlyBSD/OpenBSD interface ROUTE_MSGFILTER.
Signed-off-by: Roy Marples <roy@marples.name>
When we set "channel=0" in hostapd.conf to enable ACS function, and set
a wrong channel list, e.g., chanlist=222-999 on purpose, hostapd would
still start ACS process to compute the ideal channel, even when there
are no available channels with such configuration.
Though there is no problem since hostapd fails to initialize interface,
it spends time going through the scan and the debug log entries may make
it more difficult to tell what was behind the failure.
Thus, check if there are any available channels in acs_request_scan(),
and return -1 if no available channel, then it will fail at acs_init(),
without doing ACS computation. It will show the following in the log:
Could not select hw_mode and channel. (-3)
wlan0: interface state UNINITIALIZED->DISABLED
Then we can know the setting is incorrect already in
hostapd_select_hw_mode(), instead of waiting for scan callback function
to know if the setting is ok for ACS or not. This can save time and help
to tell if the setting is correct at the initial function at the first.
This will also allow the ENABLE control interface command to return FAIL
when adding an interface dynamically.
Signed-off-by: Neo Jou <neojou@gmail.com>
Go through the received bandSupport JSON array and print its contents in
the debug log. This information might be exposed to upper layer
configuration generation/use somehow in the future.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Most of the time is spent in the CP state machine RETIRE state where LKI
is not set and OKI is the currently used SAK so OLPN needs to be checked
for PN exhaustion.
hostapd/wpa_supplicant implemented an interpretation of the standard as
described in a proposed amendment titled "MKA pending PN exhastion"
which was deemed to be wrong. This amendment was included in IEEE Std
802.1Xck-2018.
Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz>
Most of the time is spent in the CP state machine RETIRE state where LKI
is not set and OKI is the currently used SAK, so OLPN needs to be
checked for PN exhaustion.
hostapd/wpa_supplicant implemented an interpretation of the standard as
described in a proposed amendment titled "MKA pending PN exhastion"
which was deemed to be wrong. This amendment was included in IEEE Std
802.1Xck-2018.
Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz>
The associated SAs have been deleted and the key server has changed so
there's no point in keeping the key values.
Note that this isn't specified in IEEE Std 802.1X-2010.
Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz>
Previously the ABANDON->RECEIVE state change was impossible and did not
match the CP state machine in IEEE Std 802.1X-2010 Figure 12-2.
Signed-off-by: Thomas Winter <Thomas.Winter@alliedtelesis.co.nz>
