Commit graph

426 commits

Author SHA1 Message Date
Jouni Malinen
0ef023e478 Add support for driver command to update roaming policy
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-11 15:59:42 +03:00
Jouni Malinen
71a0e395b9 P2P: Make unrecognized vendor elements available in P2P_PEER
This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-08 15:57:30 +03:00
Jouni Malinen
86bd36f0d5 Add generic mechanism for adding vendor elements into frames
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:

VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *

The following frames are supported in this commit (additional frames can
be added in the future):

0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response

One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-07 12:25:09 +03:00
Li Jianyun
6891f0e6f4 Allow SCAN command to specify scan_ssid=1 SSIDs
The new "scan_id=<comma separated list of network ids>" parameter can
now be used to specify a list of network ids that have scan_ssid=1 to
indicate active scanning of the SSID. This adds the listed SSIDs to the
scan command to allow manual scan requests to perform active scans for
hidden SSIDs. For example, "SCAN scan_id=1,7,11" would run a scan with
the SSID fetched from the configured network blocks 1, 7, and 11
(assuming those are set with scan_ssid=1). The SSIDs will be included
even from network blocks that are currently disabled.

The maximum number of SSIDs added to the request is limited by the
driver support. If more than supported values are specified, the command
will fail (returns "FAIL").

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-02 12:52:08 +03:00
Arik Nemtsov
38ddccae8f TDLS: Add ctrl_iface option for flushing all TDLS peers
"TDLS_TEARDOWN *" can now be used to tear down the direct links to all
TDLS peers. This is useful for debugging purposes.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-06-16 23:43:46 +03:00
Ilan Peer
e3bd6e9dc0 P2P: Use another interface operating channel as listen channel
Performing a P2P Device flow such as p2p_listen or
p2p_find, can degrade the performance of an active interface
connection, if the listen frequency is different than the
frequency used by that interface.

To reduce the effect of P2P Device flows on other interfaces,
try changing the listen channel of the P2P Device to match the
operating channel of one of the other active interfaces. This change
will be possible only in case that the listen channel is not forced
externally, and will be delayed to a point where the P2P Device
state machine is idle.

The optimization can be configured in the configuration file and
is disabled by default.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-06-15 00:46:11 +03:00
Jouni Malinen
0e87e798b5 Fix HS20_GET_NAI_HOME_REALM_LIST hex length check (CID 68108)
Due to an incorrect operation (MOD vs. AND), the code that was supposed
to return an error if the hex string has odd length was not really
reporting any failures. Instead of reporting an error, the invalid
control interface command would have been truncated. This is not an
issue in practice, but better fix the implementation anyway.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-12 19:45:27 +03:00
Jouni Malinen
df48efc5ab Fix external radio work stopping to not read freed memory
The dynamically allocated struct wpa_external_work contains the name of
the radio work in the type field and this is used in a debug print
within radio_work_done(). Re-order radio_work_done() and os_free() calls
on couple of paths where the memory was freed before that final user of
the buffer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-31 22:58:51 +03:00
Boris Sorochkin
e403ba859e Parse DMG capabilities when reporting to external interfaces
This adds [DMG] and [PBSS] flags for scan results and BSS table entries
using the IEEE Std 802.11ad-2012 updated definition of the Capability
field.

Signed-off-by: Boris Sorochkin <qca_bsoroc@qca.qualcomm.com>
2014-05-26 23:35:52 +03:00
Jouni Malinen
7bb70909a2 Add DRIVER_EVENT AVOID_FREQUENCIES for testing
This can be used to simulate driver events indicating frequencies to
avoid.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-05-26 17:21:44 +03:00
Jouni Malinen
e9eb648e0e P2P: Reject P2P_FIND and P2P_LISTEN on disabled interface
This makes the P2P operations behave more consistently with the SCAN
command.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-15 21:34:32 +03:00
Jouni Malinen
ad12f2f422 Add DRIVER_EVENT ctrl_iface command for testing purposes
This new command can be used to simulate driver events without having to
go through the driver wrapper or kernel code for this. This enables more
testing coverage with hwsim.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-15 21:09:48 +03:00
Dmitry Shmidt
1c330a2fdc Add 'dup_network <id_s> <id_d> <name>' command
This command allows to copy network variable from one network to
another, e.g., to clone the psk field without having to extract it from
wpa_supplicant.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-05-12 19:43:56 +03:00
Jouni Malinen
2cebdee66d Fix MinGW build
No need to use ENOBUFS within core wpa_supplicant, so just replace it
with -1 to work arounds MinGW build issues.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-29 18:59:12 +03:00
Jouni Malinen
a7ca6dac44 Fix P2P redirection of global ctrl_iface SET command
The previous version prevented all use of wpas_global_ctrl_iface_set().
That's not desirable since there may be more global parameters added in
the future. Instead, try to use the global version first and redirect to
P2P interface only if the global version returns an error.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-15 13:27:23 +03:00
Jouni Malinen
d6b818efe5 Remove SAVE_CONFIG redirect from global control interface
The P2P redirection for SAVE_CONFIG issued on the global control
interface was preventing wpas_global_ctrl_iface_save_config() from being
reached. The global version of SAVE_CONFIG was supposed to try to save
configuration files for all interface rather than just the P2P
management interface, so fix this by removing the unneeded and undesired
redirection.

Modify the global SAVE_CONFIG handler to return FAIL if no configuration
files were saved. This makes the behavior match with the per-interface
SAVE_CONFIG.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-15 13:26:48 +03:00
Jouni Malinen
023b466da4 Fix a debug print to have a space between words
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 10:26:52 +03:00
Jouni Malinen
bd8838a387 Fix ctrl_iface BLACKLIST return value
Adding a new entry was returning FAIL on success due to incorrect
assumption of wpa_blacklist_add() returning 0 on success (it returns the
positive blacklist count).

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 10:26:51 +03:00
Andres Morales
f3ff948753 P2P: Add NFC_HANDOVER commands to p2p_redir list
These commands can be executed on the P2P interface thus should be
redirected to it when issued to the global control interface.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-04-11 19:22:00 +03:00
Jouni Malinen
f05cee9714 P2P: Clear p2p_in_invitation on cancel
Commit 41d5ce9e0b added scan optimizations
for P2P invitation cases. However, it left a path where the invitation
state was not cleared and as such, introduced potential issues for
following scans that ended up getting incorrectly optimized for a single
channel regardless of parameters. Fix this by clearing p2p_in_invitation
more carefully, especially on p2p_cancel command.

p2p_cancel is now also run from the FLUSH command to avoid issues with
hwsim test cases (e.g., persistent_group_per_sta_psk followed by
ap_open_tdls resulted in an error due to p2p_in_invitation remaining set
after FLUSH).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-07 13:40:58 +03:00
Jouni Malinen
679f2e7c5f WPS NFC: Remove NFC_RX_HANDOVER_SEL
The newer NFC_REPORT_HANDOVER command is more general version that
handles the cases where NFC_RX_HANDOVER_SEL could potentially have been
used. In addition, with the new WPS NFC design, it is important to
receive the handover request message that was used in the handover in
addition to the select message, so the NFC_RX_HANDOVER_SEL command on
its own would not be sufficient for this.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-07 00:56:04 +03:00
Jouni Malinen
9ff4de6de4 Move DROP_SA command to be within ifdef CONFIG_TESTING_OPTIONS
This is a test command and has no use in production builds.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-05 23:59:31 +03:00
Dmitry Shmidt
204c9ac4ee Extend select_network command with freq= to reduce scan time
This allows a subset of channels to be specified for the scan used to
find the network when the SELECT_NETWORK ctrl_iface command is issued.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-04-04 23:07:17 +03:00
Jouni Malinen
c880ab87ee Interworking: Add GET_CRED ctrl_iface command
"GET_CRED <id> <field>" can now be used to fetch credential parameters
over the control interface. This does not allow passwords etc. private
material to be retrieved ("*" is returned for those if the value is set
regardless of the value). FAIL is returned if the requested parameter
has not been set. For cred parameters that can have multiple values,
newline separated list of values is returned.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-04 20:13:53 +03:00
Jouni Malinen
1619e9d512 Interworking: Add ctrl_iface events on cred block modifications
Following events are now sent to ctrl_iface monitors to indicate if
credential blocks have been added, modified, or removed:

CRED-ADDED <id>
CRED-MODIFIED <id> <field>
CRED-REMOVE <id>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-04 19:10:47 +03:00
Dmitry Shmidt
cf28c66bcb HS 2.0: Extend ANQP_GET to accept Hotspot 2.0 subtypes
This allows a single ANQP query to be used to fetch both IEEE 802.11
defined ANQP elements and Hotspot 2.0 vendor specific elements.

ANQP_GET <addr> <info id>[,<info id>]...
[,hs20:<subtype>][...,hs20:<subtype>]

For example:
ANQP_GET 00:11:22:33:44:55:66 258,268,hs20:3,hs20:4

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-25 18:33:21 +02:00
Jouni Malinen
c201f93a9e WPS: Enable WSC 2.0 support unconditionally
There is not much point in building devices with WPS 1.0 only supported
nowadays. As such, there is not sufficient justification for maintaining
extra complexity for the CONFIG_WPS2 build option either. Remove this by
enabling WSC 2.0 support unconditionally.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 18:33:21 +02:00
Dmitry Shmidt
d3c9c35f32 Add freq= parameter to 'set pno' command
This allows channels-to-be-scanned to be specified for PNO similarly to
the scan command.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-21 23:56:46 +02:00
Jouni Malinen
1120e45232 Allow config blobs to be set through ctrl_iface
"SET blob <name> <hexdump>" can now be used to set a configuration blob
through the wpa_supplicant control interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-15 23:51:37 +02:00
Jouni Malinen
6829da39e6 Fix external radio_work deinit path
The radio_work type was stored within the dynamically allocated
wpa_radio_work buffer and that buffer ended up getting freed before the
final use of the type string within radio_work_done(). This resulted in
freed memory being used for a debug print. Avoid this by freeing the
wpa_external_work instance after having completed radio_work_done() for
the related work.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-14 21:58:46 +02:00
Dmitry Shmidt
6e9375e4e1 TDLS: Add get_capability tdls command
Command returns info in format: UNSUPPORTED/INTERNAL/EXTERNAL

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-14 21:40:57 +02:00
Peter Qiu
0f44ec8eba Add a reattach command for fast reassociate-back-to-same-BSS
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.

Signed-hostap: Peter Qiu <zqiu@chromium.org>
2014-03-11 19:38:01 +02:00
Alexander Bondar
737e7a08b0 PNO: Move and rename pno_start()/pno_stop()
Move pno_start() and pno_stop() to scan.c as a more relevant location
and rename them to wpas_start_pno()/wpas_stop_pno().

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-11 19:12:57 +02:00
Jouni Malinen
60b893dfb3 wpa_supplicant: Allow external management frame processing for testing
This enables more convenient protocol testing of AP and P2P
functionality in various error cases and unexpected sequences without
having to implement each test scenario within wpa_supplicant.
ext_mgmt_frame_handle parameter can be set to 1 to move all management
frame processing into an external program through control interface
events (MGMT-RX and MGMT-TX-STATUS) and command (MGMT_TX). This is
similar to the test interface that was added to hostapd previously, but
allows more control on offchannel operations and more direct integration
with the internal P2P module.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-08 20:21:21 +02:00
Beni Lev
adef89480d nl80211: Add vendor command support
Add a callback to the driver interface that allows vendor specific
commands to be sent. In addition, a control interface command is added
to expose this new interface outside wpa_supplicant:

Vendor command's format:
VENDOR <vendor id> <sub command id> [<hex formatted data>]

The 3rd argument will be converted to binary data and then passed as
argument to the sub command.

This interface is driver independent, but for now, this is only
implemented for the nl80211 driver interface using the cfg80211 vendor
commands.

Signed-off-by: Beni Lev <beni.lev@intel.com>
2014-03-04 22:24:20 +02:00
Jouni Malinen
ea3b8c1d2d Do not use a separate variable for tracking first entry in a list
The pos pointer can be compared to the start of the buffer pointer to
determine whether the entry is the first one in the list. This gets rid
of some static analyzer warnings about unused variable writes.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-03-02 17:15:12 +02:00
Jouni Malinen
aa26ba68b4 HS 2.0R2: Add tracking of provisioning SP
The new provisioning_sp cred field can now be used to track which SP
provisioned the credential. This makes it easier to find the matching
PPS MO from the management tree (./Wi-Fi/<provisioning_sp>).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
b572df8650 HS 2.0R2: Add routine for fetching OSU provider information
The new wpa_cli fetch_osu command can be used to fetch information about
all OSU providers and write that to a text file with the icons in
separate files. cancel_osu_fetch command can be used to stop ongoing OSU
provider list fetch.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
1d2215fc67 HS 2.0R2: Add OSU Providers list ANQP element
wpa_supplicant can now request OSU Providers list with "hs20_anqp_get
<BSSID> 8".

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
184e110caf HS 2.0R2: Add Icon Request and Icon binary File ANQP elements
wpa_supplicant can request OSU icon data with "hs20_icon_request <BSSID>
<icon filename>". This transmits an Icon Request ANQP element and
processes the response in Icon Binary File ANQP elements.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
f9cd147d6b HS 2.0R2: Update Indication element to Release 2
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).

The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:22 +02:00
Jouni Malinen
2c49d04cdb Do not clear global pmf setting on FLUSH
This parameter was actually used in some testing cases in a way that did
not really work well with the FLUSH command ending up disabling PMF.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:22 +02:00
Jouni Malinen
3d910ef497 Interworking: Prefer last added network during network selection
Previously, any network block could be used to select the BSS to connect
to when processing scan results after Interworking network selection.
This can result in somewhat unexpected network selection in cases where
credential preferences indicated that a specific network was selected,
but another network ended up getting used for the connection. While the
older networks continue to be valid, add special processing for this
initial post-interworking-connect case to get more consistent network
selection to match with the Interworking network selection result.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-25 22:37:57 +02:00
Jouni Malinen
ea449b5bfe tests: Add a module test integration to hwsim tests
CONFIG_MODULE_TESTS=y build option can now be used to build in module
tests into hostapd and wpa_supplicant binaries. These test cases will be
used to get better testing coverage for various details that are
difficult to test otherwise through the control interface control. A
single control interface command is used to executed these tests within
the hwsim test framework. This commit adds just the new mechanism, but no
module tests are yet integrated into this mechanism.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-02-21 13:08:08 +02:00
Andrei Otcheretianski
b3253ebb73 wpa_supplicant: Complete radio works on disable event
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.

Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.

To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-02-16 00:06:23 +02:00
Jouni Malinen
2dff9e87b9 Remove unused NFC_RX_HANDOVER_REQ
The more generic NFC_REPORT_HANDOVER is now used to report completed NFC
connection handover operations in either role and NFC_RX_HANDOVER_REQ
did not have any implementation within wpa_supplicant.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-02-15 11:22:26 +02:00
Eytan Lifshitz
5e6aa04b09 wpa_supplicant: Fix memory leak in wfd_subelems error path
Memory allocated by calling function ieee802_11_vendor_ie_concat()
was not freed on an error path int ctrl_iface BSS command.

Signed-hostap: Eytan Lifshitz <eytan.lifshitz@intel.com>
2014-02-13 15:41:15 +02:00
Jouni Malinen
88853aedf6 Fix CONFIG_WPS_NFC=y build without CONFIG_P2P=y
Some of the control interface operations for P2P were not properly
protected with #ifdef CONFIG_P2P.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-02-13 15:29:09 +02:00
Mahesh A Saptasagar
062a7c0d67 Fix persistent P2P connection failure in case channel list changes
P2P persistent connection may fail due to 802.11d channel change event
invalidating support of the operating frequency sent in the invitation
request, before receiving the invitation response. If the operating
frequency is invalid at the time the invitation response is processed
and there is no forced frequency provided by user, allow frequency
re-selection.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-07 15:44:41 +02:00
Dmitry Shmidt
0547124d47 wpa_supplicant: Add DFS indicator to get_capability freq
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-02-06 16:13:10 +02:00
Jouni Malinen
bab6677a31 Handle Wi-Fi Display commands more carefully if P2P is disabled
If P2P was disabled (e.g., due to driver not supporting it or through
p2p_disabled=1 configuration), setting Wi-Fi Display parameters could
result in segmentation fault when the WFD IE is updated without the P2P
module being initialized. Fix this by skipping the update if P2P module
is not in use. In addition, show Wi-Fi Display as disabled in "GET
wifi_display" and refuse to enable it with "SET wifi_display 1" if P2P
is not enabled.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-02-06 16:03:42 +02:00
Jouni Malinen
b56f6c8869 P2P NFC: Add support for freq option in NFC ctrl_iface commands
This can be used to force an operating channel for P2P group formation
triggered by NFC operations.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:44:31 +02:00
Jouni Malinen
91a65018d8 WPS NFC: Use BSSID and AP Channel from handover select
These optional attributes, if present, can be used to speed up the
initial connection by using a single channel scan.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:44:31 +02:00
Jouni Malinen
91226e0d12 WPS: Add testing option to corrupt public key hash
If CONFIG_WPS_TESTING=y is enabled in build configuration, the new
wps_corrupt_pkhash parameter (similar to wps_testing_dummy_cred) can be
used to request public key hash to be corrupted in all generated OOB
Device Password attributes. This can be used for testing purposes to
validate public key hash validation steps.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:44:31 +02:00
Jouni Malinen
73127764fe WPS NFC: add more debug prints for connection handover report
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:44:31 +02:00
Jouni Malinen
23318bea94 P2P NFC: Optimize join-a-group operation based on NFC information
When the NFC connection handover message received from a peer indicates
that the peer is operating as a GO on a specific channel, use that
information to avoid having to go through full scan. In addition, skip
the separate join-a-group scan since we already know the operating
channel, GO P2P Device Address, and SSID.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:44:30 +02:00
Jouni Malinen
201b0f5fa6 P2P: Add test option to disable IP address assignment request
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:44:30 +02:00
Jouni Malinen
c4f87a701b P2P NFC: Add NFC tag enabling for static handover
The device with the NFC Tag can be configured to enable NFC to be used
with "P2P_SET nfc_tag 1" and "P2P_LISTEN" commands to allow static
handover to be used.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:56 +02:00
Jouni Malinen
db6ae69e6b P2P NFC: Report connection handover as trigger for P2P
"NFC_REPORT_HANDOVER {INIT,RESP} P2P <req> <sel>" can now be used to
report completed NFC negotiated connection handover in which the P2P
alternative carrier was selected.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:56 +02:00
Jouni Malinen
9358878055 P2P NFC: Build connection handover messages
"NFC_GET_HANDOVER_{REQ,SEL} NDEF P2P-CR" can now be used to build P2P
alternative carrier record for NFC connection handover request/select
messages.

Static connection handover case can be enabled by configuring the DH
parameters (either with wps_nfc_* configuration parameters or with
WPS_NFC_TOKEN command at run time. The NFC Tag contents can be generated
with "NFC_GET_HANDOVER_SEL NDEF P2P-CR-TAG" after having configured
Listen channel (p2p_listen_reg_class/p2p_listen_channel).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:56 +02:00
Jouni Malinen
50d1f8901c NFC: Update WPS ER to use the new connection handover design
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:55 +02:00
Jouni Malinen
d95079361b WPS NFC: Add support for wpa_supplicant AP/GO mode to use handover
New functionality is needed for this with the update NFC connection
handover design that depends on the AP side using the public key hash
from the handover request.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:55 +02:00
Jouni Malinen
41f9ffb635 WPS NFC: Build new style carrier record for connection handover request
It is more useful to be able to build a single NFC carrier record
instead of the full connection handover request message to allow
external components to decide whether to negotiate which alternative
carrier is used. This updates the carrier record contents to the new
design to include Enrollee public key hash and provides this as a
carrier record instead of full message. An external program is expected
to be used to build the full NFC connection handover message with
potentially other alternative carrier records included.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:55 +02:00
Jouni Malinen
57630e658b WPS: Preparations for allowing SSID filtering for provisioning step
If the SSID of the WPS AP is known, it should be possible to limit AP
selection based on this when searching for an active WPS AP. This commit
adds a mechanism to specify SSID for this type of uses.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:55 +02:00
Jouni Malinen
5f4545573f WPS NFC: Validate peer public key hash on Enrollee
Since the Enrollee can now get the public key hash from the Registrar,
there is need to validate this during the WPS protocol run.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-27 21:10:55 +02:00
Jouni Malinen
ea6e040c30 Clear more configuration parameters to default on FLUSH
This makes it more convenient for test scripts to change parameters for
a specific test case without having to separately clear them between
each test case.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-23 10:21:49 +02:00
Raja Mani
cf70d2981d wpa_supplicant: Schedule PNO on completion of ongoing sched_scan
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.

In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-22 19:41:45 +02:00
Max Stepanov
a6cff8bfa8 wpa_supplicant: Fix seg fault in wpas_ctrl_radio_work_flush() in error case
Verify wpa_s->radio pointer before accessing it. If interface addition
fails, this could get called before wpa_s->radio has been set.

The segmentation fault details:

Program received signal SIGSEGV, Segmentation fault.
0x00000000004b9591 in wpas_ctrl_radio_work_flush (wpa_s=0x77fff0) at ctrl_iface.c:5754
5754		dl_list_for_each_safe(work, tmp, &wpa_s->radio->work,

Call stack:
0  wpas_ctrl_radio_work_flush (wpa_s=0x77fff0) at ctrl_iface.c:5754
1  wpa_supplicant_deinit_iface (wpa_s=0x77fff0, notify=0, terminate=0) at wpa_supplicant.c:3619
2  wpa_supplicant_add_iface (global=0x75db10, iface=0x7fffffffe270) at wpa_supplicant.c:3691
3  wpas_p2p_add_p2pdev_interface (wpa_s=0x75dd20) at p2p_supplicant.c:3700
4  main (argc=<optimized out>, argv=<optimized out>) at main.c:317

Function:
5750	void wpas_ctrl_radio_work_flush(struct wpa_supplicant *wpa_s)
5751	{
5752		struct wpa_radio_work *work, *tmp;
5753
5754		dl_list_for_each_safe(work, tmp, &wpa_s->radio->work,
5755				      struct wpa_radio_work, list) {
5756			struct wpa_external_work *ework;
5757
5758			if (os_strncmp(work->type, "ext:", 4) != 0)

Root cause:
(gdb) p wpa_s->radio
$1 = (struct wpa_radio *) 0x0

Signed-hostap: Max Stepanov <Max.Stepanov@intel.com>
2014-01-22 19:25:22 +02:00
Dmitry Shmidt
443427e4ed P2P: Add missing direct global ctrl_iface commands for P2P
It should be noted that these commands are not exclusively used for P2P
or in the global context, so use of these commands through the global
control interface for operations that are specific to a single interface
have undefined behavior and that behavior may change in the future. As
such, these are recommend only for operations that are in the global
context (e.g., for P2P management).

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-01-17 11:58:36 +02:00
Jouni Malinen
78f0c933e0 Flush secondary device types on FLUSH command
This makes it possible to clear previously configured secondary device
types.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-08 22:27:30 +02:00
Jouni Malinen
2b384109f2 P2P: Allow requested device type to be specified with p2p_find
This allows filtering of P2P peers that reply to the device discovery
Probe Request frames.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-08 20:01:19 +02:00
Jouni Malinen
d9bb2821e7 Clear configuration blobs on FLUSH command
All te network blocks and credentials were already cleared, but
configurations blobs should also be cleared here, e.g., to get
more consistent behavior test cases using EAP-FAST PACs.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-08 16:42:15 +02:00
Jouni Malinen
b6a9590b34 Interworking: Keep up to two pending GAS_REQUEST responses
Previously, only the last response data was kept in memory. This
increases that to hold up to two last responses to allow some more
parallel operations to be requested. In addition, the response data is
now freed as soon as the external program has fetched it.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:12 +02:00
Jouni Malinen
356d1488c4 Interworking: Add optional freq argument to INTERWORKING_SELECT
This can be used to limit which channels are scanned using the specified
list of frequency ranges in the same format that the SCAN command uses.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
083916c022 P2P: Clear p2p_disabled and p2p_per_sta_psk on FLUSH command
The control interface FLUSH command now includes clearing of
"P2P_SET disabled 1" and "P2P_SET per_sta_psk 1".

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
3f45fc403f P2P: Clear services on FLUSH command
The control interface FLUSH command now includes the step executed by
the P2P_SERVICE_FLUSH command.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
1f965e622a Allow external programs to request wpa_radio work items
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
b1ae396f59 Add framework for exclusive radio operations
The new radio work item concept can be used to request time for an
operation that requires exclusive radio control, e.g., a scan. Once the
radio is available, the registered callback function will be called.
radio_work_done() must be called once the exclusive radio operation has
been completed, so that the radio is freed for other operations. The
special case of deinit=1 is used to free the context data during
interface removal. That does not allow the callback function to start
the radio operation, i.e., it needs to free the allocated resources
and return.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:37:03 +02:00
Jouni Malinen
d31b5ac778 Use cleaner debug print for ctrl_iface commands with private info
Convert this to a text string instead of ASCII hexdump to make the
debug log more convenient to use.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:33:50 +02:00
Jouni Malinen
9595151f3f Remove duplicated RX ctrl_iface hexdump
The newer wpa_dbg() print includes the same information in a more
convenient form, so remove the duplicate RX ctrl_iface hexdump in the
cases where there is no key material in the control interface commands
(the possible-key-material case is still using wpa_hexdump_ascii_key).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:33:18 +02:00
Jouni Malinen
949938aadf Ask driver to report only new scan results if requested
If the BSS table within wpa_supplicant is flushed, request the driver to
flush its own scan result table during the next scan. This can avoid
unexpected old BSS entries showing up after BSS_FLUSH or FLUSH command
in cases where the driver may maintain its internal cache of scan
results (e.g., cfg80211 BSS table persists at least for 15 seconds).

In addition to doing this automatically on BSS_FLUSH/FLUSH, a new SCAN
command argument, only_new=1, can be used to request a manual scan
request to do same. Though, it should be noted that this maintains the
BSS table within wpa_supplicant. BSS_FLUSH followed by SCAN command can
be used to clear all BSS entries from both the driver and
wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-02 23:03:31 +02:00
Jouni Malinen
0187c41d88 Declare wpa_debug_* variables in src/utils/wpa_debug.h
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 19:29:52 +02:00
Jouni Malinen
fcc61230d1 Declare wpa_drivers in src/drivers/driver.h
This avoids some warnings from sparse.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 19:19:37 +02:00
Jouni Malinen
0d79b50ae7 Clear EAPOL Logoff state on FLUSH command
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 19:03:39 +02:00
Jouni Malinen
04f7ecc686 Reset WPA parameters to default values on FLUSH command
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-29 19:25:05 +02:00
Jouni Malinen
8aaafcee9e Make local UUID available through ctrl_iface STATUS command
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-29 10:00:32 +02:00
Jouni Malinen
7b02375a41 Clear wps_fragment_size on FLUSH command
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-29 10:00:32 +02:00
Jouni Malinen
9d2cb3ec94 Make CONFIG_TESTING_OPTIONS=y enable all testing options
This makes it easier to enable various testing parameters and
functionality in build configuration.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-12-26 20:50:28 +02:00
Jouni Malinen
d81c73be18 Optional scan id for ctrl_iface SCAN requests
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:

CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:48:52 +02:00
Jouni Malinen
88c2d48860 Allow passive scan to be requested with SCAN passive=1
This allows external programs to request wpa_supplicant to execute
a passive scan (i.e., do not send any Probe Request frames).

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:27:48 +02:00
Jouni Malinen
fee5234284 Allow channel list to be specified for SCAN command
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 16:55:44 +02:00
Jouni Malinen
4daa011be4 Clean up cipher capability prints
Use an array of ciphers and a loop instead of copy-pasted copies of the
same printing functionality for each cipher.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-25 10:44:06 +02:00
Jouni Malinen
30675c3416 Add definitions for new cipher suites from IEEE Std 802.11ac-2013
This adds initial parts for supporting the new GCMP-256, CCMP-256,
BIP-GMAC-128, BIP-GMAC-256, and BIP-CMAC-256 cipher suites.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-24 22:21:04 +02:00
Johannes Berg
acb69cec6f wpa_supplicant: Use monotonic time for RX/BSS times
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:27:02 +02:00
Dmitry Shmidt
a94737ea38 Android: P2P: Remember country locale
This updates P2P modules based on the Android specific
DRIVER COUNTRY command.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2013-11-22 20:23:16 +02:00
Jouni Malinen
5e2c3490d5 Android: Add driver_cmd for arbitrary driver commands
This is a mechanism used in Android to extend driver interface in vendor
specific ways. This is included only for the purpose of Android
compatibility. Proper interface commands should be used for any new
functionality.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-22 20:23:08 +02:00
Jithu Jance
f86d282f43 Handle legacy scan interruption of sched_scan/PNO
While starting from PNO start context, the scheduled scan was not
setting the flag wpa_s->scanning. This was resulting in the subsequent
SCAN command to proceed further and send command to nl80211/cfg80211.
The expected behavior of cancelling sched_scan was not happening here.

While sched_scan is in progress and a legacy scan comes on the
cli/socket, the sched_scan is cancelled and normal scan is allowed to
continue. However, sometimes sched_scan cancelled event comes a bit
delayed and we will send out the scan command before the wpa_s->scanning
is cleared. Instead, reschedule the incoming scan req if the
wpa_s->scanning shows that it is still in progress.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2013-11-18 14:35:48 +02:00
Andrei Otcheretianski
334bf36ac5 Add chan_switch to ctrl interface of wpa_supplicant and hostapd
Add chan_switch to the control interface of wpa_supplicant and hostapd,
and also to wpa_cli and hostapd_cli.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2013-11-17 17:12:58 +02:00
Dmitry Shmidt
f6c2b8c367 Android: Add state message sent after 'status' command
This triggers re-transmission of CTRL-EVENT-STATE-CHANGE and
CTRL-EVENT-CONNECTED events on STATUS command for Android framework
specific processing.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2013-11-17 16:47:56 +02:00
Sunil Dutt
800d58721c TDLS: Provide external control to specify the peers for setup
There are use cases requesting the host driver to initiate the TDLS
setup with the peer only when configured by the external applications.
Thus, enable this control by tdls_external_control=1 and pass the
requisite information for the specific TDLS operation to the driver
on the request from such use cases.

This operation mode expects the driver to initiate TDLS link
automatically based on signal strength and traffic to a peer and tear
down links whenever they are not used or suitable due to signal strength
etc. The list of peers with which such operations are to be performed
are provided with the TDLS driver operations.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-15 03:02:08 +02:00