The newer NFC_REPORT_HANDOVER command is more general version that
handles the cases where NFC_RX_HANDOVER_SEL could potentially have been
used. In addition, with the new WPS NFC design, it is important to
receive the handover request message that was used in the handover in
addition to the select message, so the NFC_RX_HANDOVER_SEL command on
its own would not be sufficient for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
run-tests.py now takes an optional --long parameter that can be used to
enable running of test cases that take a long time (multiple minutes).
By default, such test cases are skipped to avoid making the normal test
run take excessive amounts of time.
As an initial long test case, verify WPS PBC walk time expiration (two
minutes).
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that WPS 2.0 support is enabled unconditionally, WEP and Shared auth
type are not allowed. This made some of the older code unused and that
can now be removed to clean up the implementation. There is still one
place where WEP is allowed for testing purposes: wpa_supplicant as
Registrar trying to configure an AP to use WEP. That is now only allowed
in CONFIG_TESTING_OPTIONS=y builds, though.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is somewhat of a corner case since there is no real point in using
so short a fragmentation threshold that it would result in this message
getting fragmented. Anyway, it is better be complete and support this
case as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
If fragmentation is used, the temporary inbuf/outbuf could have been
leaked in error cases (e.g., reaching maximum number of roundtrips).
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit dbfb8e82ff changed the Action frame
RX payload pointer design to point to a different field. WNM Sleep Mode
Response handler updated one of the uses to accommodate this change, but
that commit missed another use for key data length. This resulted in GTK
and IGTK being ignored in many cases when waking up from WNM Sleep Mode
with PMF enabled.
Signed-off-by: Jouni Malinen <j@w1.fi>
"SET tdls_testing 0x800" can be used to enable a special test mode that
forces the FTIE MIC in TDLS setup messages to be incorrect.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the allocated configuration parameter did not free the previous
value if a configuration file or ctrl_iface SET command updated a
previously set value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows a subset of channels to be specified for the scan used to
find the network when the SELECT_NETWORK ctrl_iface command is issued.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
req_conn_capab and required_roaming_consortium parameters were not
written into the cred block when requesting wpa_supplicant to write the
configuration file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
"GET_CRED <id> <field>" can now be used to fetch credential parameters
over the control interface. This does not allow passwords etc. private
material to be retrieved ("*" is returned for those if the value is set
regardless of the value). FAIL is returned if the requested parameter
has not been set. For cred parameters that can have multiple values,
newline separated list of values is returned.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Following events are now sent to ctrl_iface monitors to indicate if
credential blocks have been added, modified, or removed:
CRED-ADDED <id>
CRED-MODIFIED <id> <field>
CRED-REMOVE <id>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is required to read IMSI from SIM if it has not already been done
when comparing HS 2.0 AP 3GPP information with the local credentials.
Signed-off-by: Jean Trivelly <jean.trivelly@intel.com>
