wpa_supplicant can now generate the WPS carrier record for connection
handover response when acting as an ER. The AP whose configuration is
provided in this way is identified with an UUID as an argument to
wps-nfc.py.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the alternative carrier record for NFC connection handover select
message similarly to the way this is done in hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When wpa_supplicant is controlling an AP mode interface, it can generate
the NFC configuration token similarly to the way this is done in
hostapd.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
"WPS_NFC_TOKEN <WPS/NDEF>" used to generate a new NFC password token
regardless of whether there was a pre-configured token in the
configuration. Change this to use the pre-configured value, if
available, instead. This allows the same command to be used to write the
password token to an NFC tag more conveniently.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Instead of reporting only one connection handover message, report
completion of NFC connection handover with carrier record from both the
request and select messages.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since there could be multiple carrier records, it is cleaner to build
only the WPS carrier record instead of full NFC connection handover
request within wpa_supplicant.
Signed-hostap: Jouni Malinen <j@w1.fi>
Even though this command is very unlikely to fail, in theory, it could
and the WPS connection would fail in such a case. Return more clearer
failure indication in such a case without even trying to start
reassociation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Network blocks are disabled during a WPS provisioning step and 10
seconds after this to allow the newly provisioned network to be
selected. The disabled=1 flag gets written to the configuration file
when the credential is added since it happens during this process.
Update the file again after the networks have been re-enabled to avoid
leaving the configuration file into state that is not consistent with
the running configuration.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 17a4734dc4 shall optimize the
post-WPS scan based on the channel used during the provisioning only
when the EAP-Failure frame is received. In cases where the EAP-Failure
frame is missed, this optimization shall not happen resulting in the
scan in all the channels thus consuming more time for the connection.
This commit enhances this by storing the requisite information after
the M8 frame is received.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The UFD (USB flash drive) configuration method was deprecated in WSC
2.0. Since this is not known to be used, remove the UFD implementation
from hostapd and wpa_supplicant to allow the WPS implementation to be
cleaned up. This removes the now unused OOB operations and ctrl_iface
commands that had already been deprecated by the new NFC operations.
Signed-hostap: Jouni Malinen <j@w1.fi>
If WPS Registrar tries to provision a WPA/WPA2-Personal network without
including a valid Network Key, the network block cannot be used to
connect to the network. Reject such credential without adding the
network block. This makes wpa_supplicant send WSC_NACK as a response to
the invalid Credential and stop the provisioning process immediately
rather than only after trying unsuccessfully to connect to the network.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The old WPS interface for using NFC has no known deployments and even
the binary libraries referenced here are not easily available anymore.
Since the new interface for using NFC with WPS covers the same
functionality, remove the old implementation to clean up WPS
implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This commit adds new wpa_supplicant ctrl_iface commands to allow
external programs to go through NFC connection handover mechanism
with wpa_supplicant taking care of the WPS processing. This version
includes only the case where wpa_supplicant is operating as a
station/Enrollee.
Signed-hostap: Jouni Malinen <j@w1.fi>
During the association for the WPS handshake all the other configured
networks are disabled. This patch makes wpa_supplicant reenable the
disabled networks after the success/failure of the WPS handshake.
Signed-hostap: Sunil Dutt Undekari <duttus@codeaurora.org>
When I use CONFIG_WPS_NFC=y a warning appears.
wps_supplicant.c:1872:12: warning: 'wpas_wps_add_nfc_password_token'
defined but not used [-Wunused-function]
This patch removes this warning.
Signed-hostap: Masashi Honma <masashi.honma at gmail.com>
This allows the BSS selection functions to be called without having the
scan result data structure. This can be used to skip extra scans in
cases where previous results can be considered fresh.
Signed-hostap: Jouni Malinen <j@w1.fi>
Clear the possible blacklisting of a WPS AP during WPS PIN iteration if
the AP moves to selected registrar TRUE state or if it adds our MAC
address to the list of authorized MACs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Maintain state of WPS APs during iteration to find the correct AP for
WPS PIN operation when no specific BSSID is specified. This information
can be used for optimizing the order in which the APs are tried. This
commit is only adding the collection of the information and more
detailed debug information to make debug logs more helpful in figuring
out how the AP selection order could be improved.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If 4-way handshake fails due to likely PSK failure or if EAP
authentication fails, disable the network block temporarily. Use longer
duration if multiple consecutive failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
The WPA_AUTH_WPA and WPA_AUTH_WPA2 cases have already been rejected in
this function when execution comes here. In theory, support for
WPA-Enterprise could be added, but since that has not happened over the
years, there is no good reason to keep this dead code here.
Signed-hostap: Jouni Malinen <j@w1.fi>
dev.config_methods was not updated when wps_update_config was called.
This could lead to mismatching config methods between Probe Request and
M1 packets. Add missing part for it.
P2P group is only going to use a single GO, so we can leave the fixed
BSSID parameter set for the actual data connection in addition to the
initial WPS provisionign step. This can speed up operations with drivers
that select BSS internally by allowing them to skip an extra scan when
the BSSID and frequency of the GO is already known.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
os_random() may not be seeded properly, so use stronger mechanism for
generating the password id for NFC password tokens.
Signed-hostap: Jouni Malinen <j@w1.fi>
The AP PIN on wps_reg command can now be replaced with special value
"nfc-pw" to use device password from a NFC password token from the AP.
Signed-hostap: Jouni Malinen <j@w1.fi>
WPS_ER_NFC_CONFIG_TOKEN command can now be used to build a NFC
configuration token based on AP Settings learnt with WPS_ER_LEARN
or set with WPS_ER_CONFIG.
Signed-hostap: Jouni Malinen <j@w1.fi>
The new wpa_supplicant ctrl_iface command WPS_NFC_TAG_READ can now be
used to process NFC tags read by external programs to initiate
wpa_supplicant to use NFC Configuration Token to create a new network.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of requiring low-level access to an NFC device and synchronous
operations, the new WPS_NFC_TOKEN and WPS_NFC ctrl_iface commands can be
used to build a NFC password token and initiate WPS protocol run using
that token (or pre-configured values) as separate commands. The
WPS_NFC_TOKEN output can be written to a NFC tag using an external
program, i.e., wpa_supplicant does not need to have low-level code for
NFC operations for this.
Signed-hostap: Jouni Malinen <j@w1.fi>
It is possible for wpa_state to be WPA_DISCONNECTED when a new scan is
scheduled to be started in the future. If wpas_wps_cancel() gets called
(e.g., through control interface wps_cancel or a P2P group removal)
while in that state, the WPS operation (scan request and special network
block) were not removed. Fix this by clearing the WPS operations both in
WPA_SCANNING and WPA_DISCONNECTED states.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
If WPS commands are used with a specific BSSID instead of wildcard,
the BSSID that was supposed to be used only for the provisioning step
may end up getting copied to the network block that gets provisioned
based on the WPS credentials. Fix this by clearing ssid->bssid_set
when creating the network block by replacing the block used for WPS
provisioning.
This issue could show up with the provisioned network not getting
selected properly with APs that have multiple radios. Depending on
the driver, this could result in only a single one of the available
BSSes being available or the connection failing completely.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
I think this should fix the following valgrind complaint:
==1972== Source and destination overlap in memcpy(0x5181708, 0x5181708, 16)
==1972== at 0x4A073BA: memcpy (mc_replace_strmem.c:602)
==1972== by 0x45872B: wpas_wps_set_uuid (wps_supplicant.c:1116)
==1972== by 0x4599EC: wpas_wps_update_config (wps_supplicant.c:1747)
==1972== by 0x4C8DB0: wpa_supplicant_update_config (wpa_supplicant.c:3090)
==1972== by 0x4C3E5E: wpa_supplicant_reload_configuration (wpa_supplicant.c:746)
==1972== by 0x4B8B37: wpa_supplicant_ctrl_iface_process (ctrl_iface.c:4082)
==1972== by 0x4BA39C: wpa_supplicant_ctrl_iface_receive (ctrl_iface_unix.c:168)
==1972== by 0x4114D4: eloop_sock_table_dispatch_table (eloop.c:335)
==1972== by 0x411541: eloop_sock_table_dispatch (eloop.c:352)
==1972== by 0x41200D: eloop_run (eloop.c:766)
==1972== by 0x4C8B43: wpa_supplicant_run (wpa_supplicant.c:3010)
==1972== by 0x4D44AD: main (main.c:286)
Signed-hostap: Ben Greear <greearb@candelatech.com>
intended-for: hostap-1
wps_vendor_ext_m1 configuration parameter can now be used to add a
vendor specific attribute into the WPS M1 message, e.g., for
Windows Vertical Pairing.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 3c85f144ce fixed issues with P2P
Action frame TX after disconnection by clearing wpa_s->assoc_freq.
This resulted in a regression to the post-WPS scan optimization that
used wpa_s->assoc_freq to enable fast single-channel scan. Fix this by
copying wpa_s->assoc_freq to a local variable before calling
wpa_supplicant_deauthenticate() that ends up calling
wpa_supplicant_mark_disassoc() which will clear assoc_freq.
Reported-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
intended-for: hostap-1
Signed-hostap: Jouni Malinen <j@w1.fi>
While the exponential increase in the lockout period provides an
efficient mitigation mechanism against brute force attacks, this
additional trigger to enter indefinite lockout period (cleared by
restarting hostapd) will limit attacks even further by giving maximum of
10 attempts (without authorized user action) even in a very long term
attack.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
If the BSSID of the AP is specified in the WPS command, the target
AP is likely already in the BSS table and its operating channel is
known. Use this information to speed up connection by only scanning
the known channel.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, the WPS scans could have been done in associated state if we
happened to be associated when the request to use WPS was received. This
can slow down scanning and end up in unexpected state if no WPS
association is tried. Avoid these issues by disconnecting when WPS
search is started.
Signed-hostap: Jouni Malinen <j@w1.fi>
When normal scan can speed up operations, use that for the first three
scan runs before starting the sched_scan to allow user space sleep more.
We do this only if the normal scan has functionality that is suitable
for this or if the sched_scan does not have better support for multiple
SSIDs.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The hardware feature data is required in several different places
throughout the code. Previously, the data was acquired and freed on
demand, but with this patch wpa_supplicant will keep a single copy
around at runtime for everyone to use.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Instead of hardcoding the Config Methods attribute value in Probe
Request frames, set this based on the configured parameter
config_methods to allow correct set of methods to be advertised.
Make sure that the WPA and EAPOL state machines do not hold a pointer
to a network configuration that is about to be freed. This can fix
potential issues with references to freed memory.
Signal is triggered if an error occurs during WPS provisioning phase.
Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Do not emit network objects during P2P group formation since such
network objects can confuse certain apps. Instead, a persistent group
object is created to allow apps to keep track of persistent groups.
Persistent group objects only represent the info needed to recreate the
group.
Also fixes a minor bug in the handling of persistent group objects
during WPS operations.
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
