Add the option to ask for VHT operation similarly to the way ht40 is
configured - either by adding 'vht' param to the relevant p2p_*
commands or by configuring p2p_go_vht=1 in the configuration file.
This patch only adds the configuration option (e.g., via control
interface). The actual handling of the VHT parameter (asking the driver
to use VHT, etc.) will be done by the following patch.
Signed-hostap: Eliad Peller <eliadx.peller@intel.com>
Offchannel operations needed for a GAS query can conflict with ongoing
scan/connection progress, so delay GAS queries if such an operation is
in progress on the current interface or any virtual interface sharing
the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, GO considered the group to be fully re-invoked after
starting beaconing on successful invitation exchange. This would leave
the group running until idle timeout (which may not be enabled) or
explicit removal if the client fails to connect for any reason. Since
the client is expected to connect immediately after the invitation
exchange that ends with status=0 (i.e., either client initiated the
exchange or it responded with success), extend group formation timeout
to cover that period until the first successfully completed data
connection. This allows the GO to remove the group automatically if the
client devices does not connect within
P2P_MAX_INITIAL_CONN_WAIT_GO_REINVOKE (15) seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, GO considered the group to be fully formed at the completed
of WPS provisioning step. This would leave the group running until idle
timeout (which may not be enabled) or explicit removal if the client
fails to connect for any reason. Since the client is expected to connect
immediately after the WPS provisioning step, extend group formation
timeout to cover that period until the first successfully completed data
connection. This allows the GO to remove the group automatically if the
client devices does not connect within P2P_MAX_INITIAL_CONN_WAIT_GO (10)
seconds.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It is possible for the GO of a persistent group to change the PSK or
remove a client when per-client PSKs are used and this can happen
without the SSID changing (i.e., the group is still valid, but just not
for a specific client). If the client side of such persistent group ends
up trying to use an invalidated persistent group information, the
connection will fail in 4-way handshake. A new WPS provisioning step is
needed to recover from this.
Detect this type of case based on two 4-way handshake failures when
acting as a P2P client in a persistent group. A new
"P2P-PERSISTENT-PSK-FAIL id=<persistent group id>" event is used to
indicate when this happens. This makes it easier for upper layers to
remove the persistent group information with "REMOVE_NETWORK <persistent
group id>" if desired (e.g., based on user confirmation).
In addition to indicating the error cases for persistent groups, all
this type of PSK failures end up in the client removing the group with
the new reason=PSK_FAILURE information in the P2P-GROUP-REMOVED event.
Signed-hostap: Jouni Malinen <j@w1.fi>
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.
Signed-hostap: Jouni Malinen <j@w1.fi>
"wpa_cli p2p_set per_sta_psk <0/1>" can now be used to disable/enable
use of per-device PSKs in P2P groups. This is disabled by default.
When enabled, a default passphrase is still generated by the GO for
legacy stations, but all P2P and non-P2P devices using WPS will get
a unique PSK.
This gives more protection for the P2P group by preventing clients from
being able to derive the unicast keys used by other clients. This is
also a step towards allowing specific clients to be removed from a group
reliably without having to tear down the full group to do so.
Signed-hostap: Jouni Malinen <j@w1.fi>
Previously, concurrent station mode scans were postponed during an
ongoing P2P group formation up to the point of completed WPS
provisioning step. This would allow a scan to be started before the P2P
client has completed association for the data connection if a scan
request were timed to hit the window between the provisioning step and
the following association. Avoid this by extending P2P-in-progress state
to continue until the first data connection has been completed as part
of group formation. Use a ten second timeout for this to avoid leaving
scans disabled indefinitely if the client fails to connect completely.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
There are devices that can operate several channels concurrently.
Change shared_vif_oper_freq() to get_shared_radio_freqs() that can
return an array of frequencies currently used by all the virtual
interfaces that share the same radio.
In addition, move it to wpa_supplicant.c, so it can be used by other
modules.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
Previously, drivers only reported if they support multiple concurrent
channels, but did not report the maximum number of supported channels.
Add this reporting to the driver capabilities and add the implementation
to driver_nl80211.
Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.
Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.
Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).
Signed-hostap: Arend van Spriel <arend@broadcom.com>
This can be useful for some test cases, so allow wpa_supplicant to be
built with special test functionality to expose the current (last
configured) GTK. This is disabled by default and can be enabled by
adding following line into .config:
CFLAGS += -DCONFIG_TESTING_GET_GTK
The GTK can then be fetched with "wpa_cli get gtk".
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This can be used to implement filtering of channels for scan and based
on that, for connection, purposes.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
The optional -G<group> command line argument can be used to specify the
group that can access the global control interface.
Signed-hostap: Jouni Malinen <j@w1.fi>
Scanning can delay concurrent operations considerably, so it is better
to avoid that while trying to connect on any of the virtual interfaces
that share the same radio.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
cfg80211 rejects the set_key operations before the IBSS network has been
fully formed, so add one more attempt to set the key for WPA-None at
IBSS joined driver event.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This option can be used only for global parameters that are not going
to be changed from settings.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Iliyan Malchev <malchev@google.com>
There may be cases where multiple BSS entries for a single BSSID are in
the table. This is mostly in automated test cases due to the AP
configuration changes, but something similar could potentially happen as
a corner case in more realistic networks, too, e.g., when an AP changes
its operating channel. Make network selection more robust by trying to
find the exact BSS entry instead of any BSS entry with a matching BSSID
when storing GAS/ANQP response.
Signed-hostap: Jouni Malinen <j@w1.fi>
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
If WPS provisioning step is completed with an AP that is in WPS
configured state, we can skip a second scan after the provisioning step
since the AP is unlikely to change its configuration in such a case.
This can speed up WPS connection a bit by removing an unneeded scan.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.
Signed-hostap: Jouni Malinen <j@w1.fi>
If a peer replies to persistent group invitation with status code 8
(unknown group), remove the peer from the p2p_client_list if we are the
GO or remove the persistent group if we are the P2P client since it
looks like that the peer has dropped persistent group credentials and
the provisioning step needs to be executed again.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
Addition of wpa_supplicant_fast_associate() made it unnecessary to call
wpas_select_network_from_last_scan() directly from other files.
Signed-hostap: Jouni Malinen <j@w1.fi>
If scan results are available when we perform a SelectNetwork, use
them to make an associate decision. This can save an entire scan
interval-worth of time in situations where something external to
wpa_supplicant (like a connection manager) has just previously
requested a scan before calling SelectNetwork.
Signed-hostap: Paul Stewart <pstew@chromium.org>
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.
Signed-hostap: Jouni Malinen <j@w1.fi>
hostapd can now be configured to use anti-clogging mechanism based on
the new sae_anti_clogging_threshold parameter (which is
dot11RSNASAEAntiCloggingThreshold in the standard). The token is
generated using a temporary key and the peer station's MAC address.
wpa_supplicant will re-try SAE authentication with the token included if
commit message is rejected with a token request.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was used to select between "(auth)" and "(reauth)" in
CTRL-EVENT-CONNECTED events. However, the variable was not cleared
anywhere else apart from the AP deinit case. As such, it did not really
provide correct information and is not really of much use even with
proper clearing added. As such, it is cleaner to just get rid of this
altogether.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit 1ff733383f added a mechanism to
work around issues due to association events and EAPOL RX events being
getting reordered. However, this applied only for the case where
wpa_supplicant is not in associated state. The same issue can happen in
roaming case with drivers that perform BSS selection internally (or in
firmware). Handle that case similarly by delaying received EAPOL frame
processing if the source address of the EAPOL frame does not match the
current BSSID.
Since wired IEEE 802.1X do not have BSSID, make this additional
workaround conditional on BSSID match having been observed during the
previous association.
This fixes issues where the initial EAPOL frame after reassociation was
either dropped (e.g., due to replay counter not increasing) or replied
to with incorrect destination address (the BSSID of the old AP). This
can result in significantly more robust roaming behavior with drivers
that do not use wpa_supplicant for BSS selection.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Both the ctrl_iface and D-Bus interface use similar functionality to
request a new connection. Combine these to a single function to avoid
need to maintain duplicated implementation.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpas_connection_failed() uses the blacklist count to figure out a
suitable time to wait for the next scan. This mechanism did not work
properly in cases where the temporary blacklist gets cleared due to no
other BSSes being available. Address this by maintaining an additional
count of blacklisting values over wpa_blacklist_clear() calls. In
addition, add one more step in the count to timeout mapping to go to 10
second interval if more than four failures are seen.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the driver does not support multi-channel concurrency and a virtual
interface that shares the same radio with the current interface is
operating there may not be need to scan other channels apart from the
current operating channel on the other virtual interface. Filter out
other channels in case we are trying to find a connection for a station
interface when we are not configured to prefer station connection and a
concurrent operation is already in process.
Signed-hostap: Jouni Malinen <j@w1.fi>
p2p_prov_disc_req() used the join parameter to figure out whether the PD
request was a user initiated or not. This does not cover all use cases
of PD, so add a separate parameter to allow caller to indicate whether
the user requested the operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
When WPS is used with NFC connection handover, the AP may indicate its
operating channel within the credential information. Use this
informatiom, if present, to speed up the scan process.
Signed-hostap: Jouni Malinen <j@w1.fi>
This replaces the previously used bogus test data in SAE messages with
the first real field. The actual SAE authentication mechanism is still
missing and the Scaler, Element, and Confirm fields are not included.
Signed-hostap: Jouni Malinen <j@w1.fi>
External programs can use this new parameter to prevent wpa_supplicant
from connecting to a list of BSSIDs and/or SSIDs. The disallowed BSSes
will still be visible in scan results and it is possible to run ANQP
operations with them, but BSS selection for connection will skip any
BSS that matches an entry in the disallowed list.
The new parameter can be set with the control interface SET command
using following syntax:
SET disallow_aps <disallow_list>
disallow_list ::= <ssid_spec> | <bssid_spec> | <disallow_list> | “”
SSID_SPEC ::= ssid <SSID_HEX>
BSSID_SPEC ::= bssid <BSSID_HEX>
For example:
wpa_cli set disallow_list "ssid 74657374 bssid 001122334455 ssid 68656c6c6f"
wpa_cli set disallow_list
(the empty value removes all entries)
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Since we have a global P2P module, the flag to trigger scan completion
events to it needs to be in similar context. The previous design
maintained this separately for each virtual interface and if P2P module
did not run its scan operation on the virtual interface that completed
the scan, P2P module would not be allowed to restart operations
properly.
Signed-hostap: Jouni Malinen <j@w1.fi>
Use configured credentials to figure out which ANQP information needs to
be fetched and only fetch those when using Interworking network
selection. The fetch_anqp command is still fetching all ANQP
information.
Signed-hostap: Jouni Malinen <j@w1.fi>
If the scan results from before ANQP fetch are fresh (less than five
seconds old), do not run a new scan when selecting the BSS after having
used Interworking network selection.
Signed-hostap: Jouni Malinen <j@w1.fi>
