In addition to running the FLUSH command again, the pending monitor
interface events need be cleared in case the driver was running a scan
when reset() is called. This avoids issues, e.g., with discovery_dev_id
failing due to an unexpected P2P-DEVICE-FOUND event that was generated
by the pending scan operation that had not yet complete when the first
dump_monitor() call in reset() happened.
Signed-hostap: Jouni Malinen <j@w1.fi>
It looks like slow virtual machines may have issues to complete some EAP
authentication cases (e.g., EAP-EKE in ap_ft_eap) within the 10 second
timeout under load. Double the timeout to avoid incorrect test failures.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for the previous test case to leave unexpected BSS or
P2P peer table entries if a scan was in progress when the FLUSH command
was used. This could result in test failures, e.g., when running
discovery_dev_type_go followed by discovery_group_client where a P2P
peer was discovered on another channel at the end of the former test
case from a scan that was running durign the FLUSH operation that was
supposed to remove all P2P peers. This could result in
discovery_group_client failing due to dev[2] trying to send the
discoverability frame on incorrect channel (the one learned in the
previous test case) since discover_peer() skipped a new device
discovery. Fix this by running FLUSH operation again if a pending scan
operation is detected during the first FLUSH operation.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
In addition, add the earlier tests in the new test_ssid.py file that was
forgotten from the previous commit
d78f33030d.
Signed-hostap: Jouni Malinen <j@w1.fi>
It was possible for this test case to fail if P2P_FLUSH was issued
during a search scan and that scan adding back the peer. Avoid this by
forcing p2p_find to be started regardless of the current P2P peer table
contents for each round of service discovery.
Signed-hostap: Jouni Malinen <j@w1.fi>
The FLUSH command clears disallow_aps, p2p_disabled, and
p2p_per_sta_psk, so there is no need to clear them separately.
Signed-hostap: Jouni Malinen <j@w1.fi>
Replace the fixed 100 ms waits with a select()-based wait and timeout
for full wait based on monotonic time to optimize wait_event().
Signed-hostap: Jouni Malinen <j@w1.fi>
No need to run a full scan as the first step since it only needs to find
the AP from a known channel for the GAS operation.
Signed-hostap: Jouni Malinen <j@w1.fi>
Now that wpa_supplicant requests the driver (cfg80211) to clear its scan
cache automatically after each BSS_FLUSH/FLUSH command, the previously
used ignore_old_scan_res workaround should not be needed for the hwsim
test cases anymore.
Signed-hostap: Jouni Malinen <j@w1.fi>
Add test cases to use connect command instead of auth+assoc commands and
AP mode operations using the old monitor interface design.
Signed-hostap: Jouni Malinen <j@w1.fi>
NOTE: Actual use of the direct link (DLS) is not supported in
mac80211_hwsim, so this operation fails at setting the keys after
successfully completed 4-way handshake. This test case does allow the
key negotiation part to be tested for coverage, though.
Signed-hostap: Jouni Malinen <j@w1.fi>
This adds number of test cases to go through various possible EAP
configurations for Interworking network selection.
Signed-hostap: Jouni Malinen <j@w1.fi>
This extends P2P test coverage to include the case of separate group
interface use with autonomous GO and group formation through GO
negotiation.
Signed-hostap: Jouni Malinen <j@w1.fi>
This fixes the user.key file (incorrect key was copied previously) and
adds a test case for EAP-TLS with WPA2-Enterprise.
Signed-hostap: Jouni Malinen <j@w1.fi>
This increases EAP method coverage for WPA2-Enterprise to include
EAP-pwd, EAP-GPSK, EAP-SAKE, EAP-EKE, EAP-IKEv2, EAP-PAX, and EAP-PSK.
Signed-hostap: Jouni Malinen <j@w1.fi>
The run-tests.py -l argument does not take an argument value anymore.
Instead, debug output is directed to a separate file <test>.log for each
test case.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
test_ap_change_ssid verifies that the SET and RELOAD control interface
commands can be used to change the SSID of a hostapd-controlled WPA2-PSK
AP, i.e., for a case where the PSK needs to be derived again after the
SSID change.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies network selection using 3GPP Network Information and
connection using EAP-SIM with GSM authentication handled by an external
program.
Signed-hostap: Jouni Malinen <j@w1.fi>
