Commit graph

310 commits

Author SHA1 Message Date
Moshe Benji
ab41595f35 wpa_supplicant: Fix crash when terminating all interfaces
In wpa_supplicant_terminate_proc(), while iterating and
terminating interfaces, after an interface is terminated,
we can no longer access its memory as it is no longer valid
and causes a crash.

Fix this by saving the pointer to the next interface before freeing
the current one to avoid accessing an invalid memory location.

Signed-hostap: Moshe Benji <moshe.benji@intel.com>
2013-12-24 08:29:28 +02:00
Johannes Berg
4e1eae1dff wpa_supplicant: Use monotonic time for temp-disabled networks
Temporarily disabled networks are disabled for a certain
duration, so the code should use monotonic time.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 08:01:59 +02:00
Johannes Berg
c2be937ce7 wpa_supplicant: Use monotonic time for EAPOL RX workaround
The EAPOL RX workaround checks that the events are less than 100 ms
apart, so only uses relative times and should use monotonic time.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:35:42 +02:00
Eliad Peller
3727123269 bgscan: Stop bgscan only on disassociation
Stopping bgscan on any state other than COMPLETED results
in bgscan reset (stop + start) on every rekeying operation.

Signed-hostap: Eliad Peller <eliad@wizery.com>
2013-12-24 06:48:28 +02:00
Jouni Malinen
429dd9aff1 Advertise QoS Map support based on driver capability
Do not assume the driver supports QoS Mapping, but instead, advertise
support for this only if CONFIG_INTERWORKING is defined and driver
indicates support for configuring QoS Map.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-12-23 11:05:20 +02:00
Tomasz Bursztyka
b154a24e83 Fix a never-ending loop with multiple radios in wpa_supplicant
Commit 202dec2a94 introduced a never
ending loop for a case where a single wpa_supplicant process is used
with multiple radios. Fix this by advancing the iface pointer properly
to the next interface in the loop until a NULL pointer is hit.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2013-12-14 21:16:05 -08:00
Jithu Jance
8567866d75 P2P: Handle frequency conflict in single channel concurrency case
Based on priority, remove the connection with least priority whenever
a frequency conflict is detected.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2013-12-07 18:55:58 -08:00
Jouni Malinen
0ad3b9c402 Use wpa_radio data for get_shared_radio_freqs()
This replaces the now unnecessary iteration of get_radio_name() calls.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 21:20:15 +02:00
Jouni Malinen
1b544ffa74 Use wpa_radio data for wpas_wpa_is_in_progress()
This replaces the now unnecessary iteration of get_radio_name() calls.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 21:20:14 +02:00
Jouni Malinen
202dec2a94 Add shared per-radio structure for wpa_supplicant
struct wpa_radio is used as a shared data structure between all struct
wpa_supplicant instances that share the same physical radio.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 21:20:14 +02:00
Jouni Malinen
73c00fd794 Move wpa_supplicant driver initialization into a helper function
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 19:36:29 +02:00
Michael Schaller
bdec7ee5c9 D-Bus: Add support to set pkcs11_{engine,module}_path
Add SetPKCS11EngineAndModulePath D-Bus method. Add PKCS11EnginePath
and PKCS11ModulePath D-Bus property getters.

Signed-hostap: Michael Schaller <misch@google.com>
2013-11-23 10:48:27 +02:00
Masashi Honma
22cf7d7324 SCARD: Clean up SIM/USIM selection
Commit eb32460029 left an unneeded
sim_type argument to scard_init(). Remove that unnecessary argument to
clean up the implementation.

Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
2013-11-17 16:47:38 +02:00
Jouni Malinen
217cf4991d P2P: Add more debug prints for frequency selection
This prints out get_shared_radio_freqs() results and related information
from P2P operations to make debug logs more helpful for figuring out
issues related to multi-channel concurrency.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-05 11:07:51 +02:00
Ilan Peer
9804873e53 wpa_supplicant: Fix bug in get_shared_radio_freqs
The idx variable was mistakenly set to 0 at the beginning of the
interface iteration. This could result in the operating channel of the
interface calling the function from being removed from the returned
frequency array if other interfaces were operating.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
2013-11-05 10:55:22 +02:00
Haim Dreyfuss
3139270903 bgscan: Add global bgscan configuration
This option can be used to globally configure bgscan parameters
for all the network blocks.

Note that this configuration will not override a network block
specific bgscan settings, but will only be used in case that
the network block does not have a valid bgscan configuration.

Signed-hostap: Haim Dreyfuss <haim.dreyfuss@intel.com>
2013-11-05 10:26:31 +02:00
Jouni Malinen
4d9fb08d23 WPS: Clear known_wps_freq in addition to after_wps
Both of these variables can result in optimized WPS scans, so better
clear these more consistently to avoid unexpected single-channel scans.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-27 12:56:56 +02:00
Jouni Malinen
a2a535f897 Remove unnecessary wpa_s->conf checks
wpa_s->conf cannot be NULL because wpa_supplicant_init_iface() would not
allow wpa_supplicant_add_iface() to return wpa_s instance in such state.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-26 15:55:52 +03:00
Naresh Jayaram
07041c6f99 eap_proxy: Confirm eap_proxy initialization before reading SIM info
Trying to access the SIM card details without checking if the eap_proxy
layer has been initialized can results in a crash. Address this by
sending the request for the IMSI through eapol_supp_sm.c which can
verify that eap_proxy has been initialized.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-23 20:51:39 +03:00
Jouni Malinen
d259249762 Fix ENABLE_NETWORK not to reconnect in disconnected state
DISCONNECT followed by ENABLE_NETWORK ended up starting a scan for a new
connection due to wpa_supplicant_enable_one_network() setting
wpa_s->reassociate = 1. This was done regardless of wpa_s->disconnected
being 1 which should imply that wpa_supplicant should not try to connect
before asked explicitly with REASSOCIATE or RECONNECT.

Fix this by making ENABLE_NETWORK setting of reassociate = 1 and
starting of scans for connection conditional on wpa_s->disconnected ==
0. This will make ENABLE_NETWORK trigger a connection only if
wpa_supplicant is already in a state where it would try to connect if
there are any enabled networks.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-23 12:09:46 +03:00
Jouni Malinen
af8a827b90 Make frequency range list routines more general
This allows the frequency range list implementation to be shared for
other purposes.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-23 00:44:07 +03:00
Kyeyoon Park
c377514337 GAS: Delay GAS query Tx while scanning/connecting
Offchannel operations needed for a GAS query can conflict with ongoing
scan/connection progress, so delay GAS queries if such an operation is
in progress on the current interface or any virtual interface sharing
the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-21 13:15:45 +03:00
Jouni Malinen
a5d44ac083 EAP peer: Add framework for external SIM/USIM processing
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.

Changes to the EAP methods to use this new mechanism will be added in
separate commits.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-20 13:12:04 +03:00
Jouni Malinen
56f5af489c Interworking: Add support for QoS Mapping functionality for the STA
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.

This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-18 14:13:45 +03:00
Arif Hussain
8b3b803ab9 Include Extended Capabilities element based on scan results
Add Extended Capabilities element to association request only if the AP
included this element in Beacon/Probe Response frames. This is a
workaround to address interoperability issues with some older APs that
do not seem to be able to handle Extended Capabilities element in
(Re)Association Request frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-02 08:09:05 -07:00
Jouni Malinen
20625e9753 P2P: Remove P2P groups on process termination
Killing the wpa_supplicant process or using TERMINATE ctrl_iface command
resulted in the process existing without cleaning up possibly added
dynamic P2P group interfaces. Clean this up by stopping each P2P group
before stopping eloop.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-26 01:38:30 +03:00
Vinay Krishna Eranna
b2b688d18d P2P: Fix crash when failed to create GO interface
wpa_supplicant crashes if driver configuration for AP mode interface
configuration fails after group negotiation. This is because of a
regression from commit 1075b29571 that
ends up freeing the wpa_s instance from within
wpa_supplicant_create_ap() without the caller knowing.

Fix this by using an eloop timeout to free remove the P2P group so that
wpa_supplicant_create_ap() and especially wpa_supplicant_associate()
callers do not need to know about interface getting possibly removed. In
addition, move the P2P specific code into p2p_supplicant.c where it
really belongs. This allows the already existing group formation timeout
to be used by reducing the timeout to zero.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-03 12:43:12 +03:00
Jouni Malinen
01a57fe420 P2P: Maintain list of per-client PSKs for persistent groups
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-09-01 21:35:10 +03:00
Jouni Malinen
25a8f9e316 Clear EAPOL supplicant configuration info on current_ssid changes
There were some code paths that allowed obsolete configuration data
pointer to be maintained within EAPOL supplicant in case a network was
removed while not connection to it (i.e., wpa_s->current_ssid not
pointing to the network that was removed). This could result in use of
freed memory, e.g., from eap_sm_notify_ctrl_attached() when a new
control interface connected prior to the EAPOL supplicant configuration
pointer got updated.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-08-25 19:46:57 +03:00
Sean Lin
cbf41ca796 P2P: Do not delay retries on failure during group formation
4-way handshake may fail under extremely noisy environment and if this
happens during P2P group formation, the 10 second extra delay added in
wpas_auth_failed() can result in running over the 15 second timeout.

Avoid this by skipping the delay mechanism in wpas_auth_failed() for the
P2P group formation case. The P2P formation timeout will take care of
stopping the attempts if the failure condition does not get resolved.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-07-31 23:09:34 +03:00
Jouni Malinen
a21816a933 Use wpa_drv_shared_freq() if get_radio_name() is not supported
Some driver interfaces may not support the get_radio_name() design and
get_shared_radio_freqs() needs to be aware of such possibility when
determining shared radio frequencies.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-07-21 20:48:09 +03:00
Ilan Peer
53c5dfc2c4 Change share_vif_oper_freq() to handle multiple freqs
There are devices that can operate several channels concurrently.
Change shared_vif_oper_freq() to get_shared_radio_freqs() that can
return an array of frequencies currently used by all the virtual
interfaces that share the same radio.

In addition, move it to wpa_supplicant.c, so it can be used by other
modules.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-07-21 20:03:53 +03:00
Ilan Peer
4752147d88 nl80211: Report the number of concurrent support channels
Previously, drivers only reported if they support multiple concurrent
channels, but did not report the maximum number of supported channels.
Add this reporting to the driver capabilities and add the implementation
to driver_nl80211.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-07-21 19:49:47 +03:00
Chengyi Zhao
831770bffe Cancel delayed scheduled scan when wpa_supplicant cleans up
Because a delayed scheduled scan will access the members of struct
wpa_supplicant which is freed and this can result in a crash,
wpa_supplicant needs to cancel delayed scheduled scan during cleanups.

Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
2013-07-20 17:47:02 +03:00
Jouni Malinen
78f79fe5fc P2P: Do not add ctrl interface for P2P_DEVICE (p2p-dev-*)
Adding a new wpa_supplicant control interface for the dedicated
P2P_DEVICE would be quite confusing for programs that manage P2P
operations. Remove this control interface and require the global control
interface to be used since it will provide consistent interface for both
the new dedicated P2P_DEVICE (non-netdev) and old style P2P management
through a netdev.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-07-01 00:36:33 +03:00
Jouni Malinen
1c42b42f6c P2P: Fix TDLS and l2_packet init without P2P Device interface
Commit c68f6200a7 made these calls
conditional on !p2p_mgmt, but forced p2p_mgmt=1 for cases where the
driver does not use the dedicated P2P Device. Fix this by making the
!p2p_mgmt condition apply only if the driver does indicate use of a
dedicated P2P Device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-06-30 20:02:25 +03:00
Arend van Spriel
c68f6200a7 P2P: Create P2P Device interface if supported
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.

Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.

Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).

Signed-hostap: Arend van Spriel <arend@broadcom.com>
2013-06-30 10:50:14 +03:00
Arend van Spriel
72950ed240 P2P: Remove a call to wpas_p2p_deinit_global()
In wpa_supplicant_deinit(), the function wpas_p2p_deinit_global()
was called. Remove it as it will be called from wpas_deinit_iface()
upon removal of the P2P management interface.

Signed-hostap: Arend van Spriel <arend@broadcom.com>
2013-06-25 13:56:28 +03:00
Jouni Malinen
ec7b97ab00 Interworking: Add support for using eap_proxy offload
Fetch IMSI through eap_proxy for Interworking network selection if
needed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-06-19 18:42:17 +03:00
Jouni Malinen
dad153d16b Try to use fast-associate on ENABLE_NETWORK
This makes ENABLE_NETWORK behave similarily to SELECT_NETWORK by
allowing a scan to be skipped if recent scan results are available.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-22 16:10:59 +03:00
Jouni Malinen
2925756575 wpa_supplicant: Add -G argument to specify global ctrl group
The optional -G<group> command line argument can be used to specify the
group that can access the global control interface.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-18 11:00:05 +03:00
Vinayak Kamath
e27d20bb68 WNM: Add neighbor report processing for BSS Transition Management
Process the neighbor report received in BSS Management Request frames.

Signed-hostap: Vinayak Kamath <vkamat@codeaurora.org>
2013-05-16 17:48:59 +03:00
Jouni Malinen
e679f140b9 Mark interface disconnected on removal request
This cleans up debug log by not trying to process the disconnection
event as a failure that could result in blacklist addition and auto
connect attempt. These are pointless operations since the interface is
going to removed immediately after this.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-12 19:18:55 +03:00
Jouni Malinen
0cdb93fe9f Do not add BSS to blacklist on local disconnection request
There is no point in marking a BSS temporarily blacklisted based on a
connection failure or disconnection case if that happens as a result of
a local request to disconnect. The blacklist entry could result on
unexpected BSS getting selected on the next connection attempt. In
addition, the code to try to find another BSS within the ESS could
result in scanning a single channel on the next attempt. Fix these
issues by handling the connection failure events only if we are not in
disconnected state (i.e., would try to reconnect after this
automatically).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-12 19:18:55 +03:00
Deepthi Gowri
36b9883d84 Defer scan if connection is in progress on any of the shared interfaces
Scanning can delay concurrent operations considerably, so it is better
to avoid that while trying to connect on any of the virtual interfaces
that share the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-10 16:10:50 +03:00
Jouni Malinen
6ea1f4135b Try to set WPA-None key after IBSS-joined event
cfg80211 rejects the set_key operations before the IBSS network has been
fully formed, so add one more attempt to set the key for WPA-None at
IBSS joined driver event.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-07 18:14:56 +03:00
Jouni Malinen
66562e9c75 Use cached driver capabilities instead of new fetch for each operation
There is no need to repeat the driver capability fetch for each
operation since we already cache driver flags in wpa_s->drv_flags.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-07 17:36:40 +03:00
Jouni Malinen
55a2df4389 HS 2.0: Include HS 2.0 Indication element only for HS 2.0 association
The Hotspot 2.0 specification seems to mandate this element to be
included in all (Re)Association Request frames if the station is Hotspot
2.0 capable. However, that results in conflicts with other requirements
like no TKIP use when this element is present. The design is really
supposed to include the indication element only for Hotspot 2.0
associations regardless of what the current specification implies.
Remove the HS 2.0 Indication element from (Re)Association Request frame
whenever the connection is not for Hotspot 2.0 purposes.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-05 16:29:21 +03:00
Jouni Malinen
dd57970477 Disable network temporarily on repeated connection failures
Previously, only explicit indications of authentication failures were
used to disable a network block temporarily. Extend this to use multiple
failed connection attempts as a sign of a possible authentication or
authorization failure to reduce the frequency of connection attempts
with a network that does not seem to allow connection.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-04-25 17:28:50 +03:00
Jouni Malinen
18e00b5e4d Move wpa_s freeing into wpa_supplicant_deinit_iface()
All wpa_supplicant_deinit_iface() callers ended up freeing wpa_s
immediately after this call. Move os_free(wpa_s) into the deinit
function to share the same call and make the deinit sequence clearer.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-04-23 18:07:41 +03:00