The new event can be used when EAPOL TX status can't be reported as a
complete 802.11 frame but is instead reported as just the EAPOL data as
originally passed to hapd_send_eapol().
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
This is a workaround for Windows 7 supplicant rejecting WPA msg 3/4
in case it used Secure=1 in msg 2/4. This can happen, e.g., when
rekeying PTK after EAPOL-Key Error Request (Michael MIC failure)
from the supplicant.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This cleans up the code a bit by not having to deal with theoretical
possibility of maximum number of EAP methods to be different between
various components in hostapd.
Signed-hostap: Jouni Malinen <j@w1.fi>
Commit c2ff13c533 broke this with a
copy-paste typo that ended up adding the Probe Request P2P IE into the
Beacon frame (i.e., Beacon frame had two P2P IEs while Probe Response
had none).
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
hapd->time_adv cannot really be NULL if hostapd_update_time_adv()
returns success, but this construction seems to be too difficult
for some static analyzers. While this change is not really needed
in practice, it makes it easier to go through warnings from such
analyzers.
Signed-hostap: Jouni Malinen <j@w1.fi>
Instead of trying to remember to add wpa_msg() calls for every possible
path where a STA becomes authorized or unauthorized, use
ap_sta_set_authorized() to send these events more consistently.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_msg() has to use hapd->msg_ctx instead of hapd as the context
pointer to work properly in wpa_supplicant AP mode.
Signed-hostap: Jouni Malinen <j@w1.fi>
Currently, there is no events over the control interface
when a AP disconnects a station due to inactivity. With
this patch, an "AP-STA-DISCONNECTED" event will be sent.
Signed-hostap: Nicolas Cavallari <nicolas.cavallari@lri.fr>
The GTK is renewed in the hostapd after a MIC attack dissassociation
without informing the driver, causing decryption failures. This patch
sends the new GTK/IGTK to the driver after it is updated by the hostapd.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Some stations have been reported to send EAPOL-Key Error Reports
indicating Michael MIC failures even when the cipher is not TKIP
(e.g., when the network is using only CCMP). Ignore such reports
to avoid starting TKIP countermeasures unnecessarily. This can
prevent certaint types of denial of service attacks by insiders,
but mostly this is to work around invalid station implementations.
Signed-hostap: Jouni Malinen <j@w1.fi>
The eloop timeout to stop TKIP countermeasures has to be canceled
on deinit path to avoid leaving bogus timeouts behind.
Signed-hostap: Jouni Malinen <j@w1.fi>
This was included in the AP configuration parameters, but there has
been no way to set it to anything else than the default automatic
mode. Remove this parameter and just hardcode ERP determination to
follow the automatic mode.
hostapd_wpa_auth_conf() is called on uninitialized memory and the
conditional blocks in this function may leave some fields into
uninitialized state. This can result in unexpected behavior elsewhere
since some of the variables may be used without matching #ifdef
blocks. Fix this by zeroing the memory.
The Query Response Length Limit is not allowed to be zero when
this is sent by the AP. Use 0x7F to indicate that the limit is
based on maximum number of GAS fragments.
For P2P, the p2p_connect takes in device address argument to make a
connection. However the connected event AP-STA-CONNECTED comes with
interface address. The application listening on events would find it
difficult to map interface address to the p2p device address which is
provided for connection.
Append P2P Device Address to AP-STA-CONNECTED event for P2P Client
connection. This will help applications to easily map the P2P Interface
Address to P2P Device Address on CONNECTED event. For non-P2P case, it
will just print the usual STA MAC address alone.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.
Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
Remove the separate driver_ops functions set_cts_protect(),
set_preamble(), set_short_slot_time(), and set_ht_params(). These
belong into same set of operations as set_ap(), so there is no need
to maintain separate functions that just make the driver wrapper
more complex.
Since these have only been used with driver_nl80211.c, the driver_ops
can be removed immediately instead of maintaining backwards
compatibility period with the old functions.
The AP client isolation parameter is now available through set_ap().
driver_nl80211.c was the only driver wrapper using the set_intra_bss()
call in hostap.git, but some external trees may have used this. Once
those are cleared, the set_infra_bss() driver_ops can be removed
completely. The only remaining use case for it currently is in P2P
GO mode with wpa_supplicant.
AP mode operations were used for P2P device discovery Listen state
only during early experiments. This has now been cleaned up and
ieee802_11_set_beacon() is not called for P2P device discovery.
As such, this hack to skip Beacon configuration can be removed.
This is the first step in allowing SA Query mechanism in hostapd to be
used with drivers that implement authentication and association MLME/SME
(i.e., do not use ieee802_11.c).
Commit 17f6b90056 moved the concatenation
of WPS IEs, but did not include the validation that the IE buffer is not
NULL. In addition, the concatenation needs to be done based on the full
IE buffer instead of the parsed pointer that includes only a single
WPS IE.
Data path for stations that get successfully associated to the
hostapd but fail to get added in the driver/firmware, will not
work. In such cases, hostapd should deauth and disconnect such
stations. In such scenario, hostapd should disconnect the STAs.
Sample output with following patch
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: authenticated
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: associated (aid 1)
wlan0: AP-STA-CONNECTED 0c:74:c2:9a:4c:59
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: Could not add STA to kernel driver
wlan0: STA 0c:74:c2:9a:4c:59 IEEE 802.11: deauthenticated due to local deauth request
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
The password_hash parameter was not copied in case of the integrated
authentication server (but was for RADIUS server). This broke EAP
authentication when the user entry used NT-hash.
The EAPOL authenticator was previously forcing disconnection in the WPS
use case. However, this can be benefitial operation with any IEEE 802.1X
authentication mechanism and need not be limited to WPS. This helps some
use cases like EAP-FAST where provisioning may require two
authentication runs if the authentication server does not allow the PAC
provisioning step to be used for normal data connection. While the
station would be free to decide to re-associate in such a case, not all
stations do and as such, it helps if the AP does that instead of leaving
the association up with EAPOL state machine in HELD state for 60
seconds.
When polling a station that has been inactive for a while, hostapd currently
always uses a null data frame. This is a bit strange with uAPSD clients
(though it seems to mostly work) since the EOSP bit can never be set in a
non-QoS frame. Make hostapd use QoS null data frames for probing when the
station is a QoS STA.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wrap self-generated WPS credential for new AP settings and send that to
control interface to provide the needed information in
WPS-NEW-AP-SETTINGS for external processing.
Make the WPS processing of (Re)Association Request frame IEs conditional
on WPS support. This fixes a build issue with wps_is_20() not being
defined and makes the non-WPS build a bit smaller.
The Deauth/Disassoc TX status callbacks were ending up kicking the
station entry from kernel driver when test functionality was used to
inject Deauth/Disassoc frames from the AP with the purpose of leaving
the local association in place. Fix this by using STA flags to figure
out whether there was a pending callback for the frame that we need
to act on.
In addition, add forgotten functionality for the Disassoc TX status
callback to match the behavior with Deauth.
This allows the driver to use PS buffering of Deauthentication and
Disassociation frames when the STA is in power save sleep. The STA
entry (and PTK) will be removed from the kernel only after the
Deauth/Disassoc has been transmitted (e.g., when the STA wakes up).
A hardcoded two second timeout is used to limit the length of this
window should the driver fail to deliver the frame (e.g., the STA
is out of range and does not wake up). The kernel STA entry is
marked unauthorized during the wait to avoid accepting Data
frames from the STA that we have decided to disconnect.
This behavior is available only with drivers that provide TX status
events for Deauth/Disassoc frames (nl80211 at this point). Other
drivers continue to use the previous behavior where the STA entry
is removed immediately.
Extend the code that waits for the station to send EAPOL-Start before
initiating EAPOL authenticator operations to cover the case where the
station includes WPS IE in (Re)Association Request frame if that IE
does not include support for WPS 2.0. While this should not really
be needed, this may help with some deployed WPS 1.0 stations that do
not support EAPOL operations correctly and may get confused of the
EAP-Request/Identity packets that would show up twice if EAPOL-Start
is transmitted.
If an ER tries to send a message to a STA that is not in the middle
of WPS protocol, do not try to deliver that. This can help with issues
where an ER takes long time to reply to M1 and another Registrar has
already completed negotiation.
This change is a first step in better supporting different driver
architectures for AP mode operations with nl80211. This commit in
itself does not add new functionality, but it makes it easier to add
new AP mode parameters to address needs of drivers that have more of
the MLME/SME in firmware or kernel.
Split WPA initialization into two parts so that the Beacon frames can be
configured fully before the initial keys (GTK/IGTK) are configured. This
makes it easier for drivers that depend on the AP security mode being
fully set before the keys are configured.
This avoids a request to the driver to first start beaconing before
the WPA/RSN IE has been generated and then immediately changing the
beacon IEs once the WPA/RSN IE is ready.
Reassociation Request/Response frame validation need to count all IEs in
the RIC. In addition, TIE is not protected, so it should not be included
in the count.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
When adding a new station, set the STA flags as part of the sta_add()
command. This ensures the flags are up to date when the station is added
by lower level drivers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
A new hostapd configuration parameter, disable_pmksa_caching=1, can now
be used to disable PMKSA caching on the Authenticator. This forces the
stations to complete EAP authentication on every association when WPA2
is being used.
Data path is broken when hostapd reloads its configuration
disabling the security which was previously enabled (WEP/WPA),
using kill -1, as old keys were not cleared.
The patch clears the keys configured when hostapd reloads
its configuration.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Previously hostapd just masked the STAs HT caps with its own. However,
some HT caps are not symmetric and as such need to be handled
different.
hostapd shouldn't overwrite the STAs SMPS mode as otherwise the driver
cannot know it has to use RTS/CTS to wake the receiver from dynamic
SMPS for MCS rates > 7.
hostapd shouldn't mask the RX and TX STBC caps with it's own. They are
already handled in a special case below.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This fixes an issue with SA Query Response frames not being processed
anymore after wpa_supplicant started registering a handler for those.
This handler registration is in generic driver_nl80211.c code, so
hostapd uses it, too.
If the driver wrapper is setting up the interface up only at commit(),
UPnP initialization fails. Fix that by moving UPnP setup to happen after
the driver commit() call.
Windows 7 uses incorrect way of figuring out AP's WPS capabilities by
acting as a Registrar and using M1 from the AP. The config methods
attribute in that message is supposed to indicate only the configuration
method supported by the AP in Enrollee role, i.e., to add an external
Registrar. For that case, PBC shall not be used and as such, the
PushButton config method is removed from M1 by default. If pbc_in_m1=1
is included in the configuration file, the PushButton config method is
left in M1 (if included in config_methods parameter) to allow Windows 7
to use PBC instead of PIN (e.g., from a label in the AP).
It may take some time for the TX status to be delivered for a
(Re)Association Response frame and if any Data frames are received
during that time, they may end up getting dropped as Class 3 frames in
not-associated state. This results in a Disassociation frame being sent
to the station and it assuming that the association has been lost.
Work around the issue by remembering that the (Re)Association Request
has already been accepted and skip the Deauth/Disassoc sending because
of the possible Class 3 frames before the TX status callback is
received.
Both the SA and IEs from the received Probe Request frames must be
included and the Probe Request RX callback functions may assume that
these are not NULL.
Commit 03d3f28a69 broke initialization of
EAPOL authenticator state machines since an error value from
wpa_auth_sta_key_mgmt() (-1) was not handled properly and the fixed
wpa_key_mgmt_wpa_psk() identified the value as a PSK-based AKM because
of all bits being set to 1. The special error value needs to handled
separately to avoid skipping EAPOL state machine initialization.
This should fix EAPOL reauthentication and rekeying timeout issues
with Intel clients when using WMM (e.g., with IEEE 802.11n). These
stations do not seem to be able to handle EAPOL data frames as
non-QoS Data frames after the initial setup.
This adds STA flags to hapd_send_eapol() driver op to allow
driver_nl80211.c to mark the EAPOL frames as QoS Data frame
when injecting it through the monitor interface.
Some deployed supplicants update their SNonce for every receive
EAPOL-Key message 1/4 even when these messages happen during the
same 4-way handshake. Furthermore, some of these supplicants fail
to use the first SNonce that they sent and derive an incorrect PTK
using another SNonce that does not match with what the authenticator
is using from the first received message 2/4. This results in
failed 4-way handshake whenever the EAPOL-Key 1/4 retransmission
timeout is reached. The timeout for the first retry is fixed to
100 ms in the IEEE 802.11 standard and that seems to be short
enough to make it difficult for some stations to get the response
out before retransmission.
Work around this issue by increasing the initial EAPOL-Key 1/4
timeout by 1000 ms (i.e., total timeout of 1100 ms) if the station
acknowledges reception of the EAPOL-Key frame. If the driver does
not indicate TX status for EAPOL frames, use longer initial
timeout (1000 ms) unconditionally.
Previously, a bug in GKeyDoneStations count would remain in effect
until the authenticator is restarted. Make this more robust by
clearing the station count before each rekeying setup. While this
is not really supposed to be needed, there has been bugs in this
area in the past and it is safer to make the implementation recover
from such an issue automatically.
If the STA to be freed is still included in GKeyDoneStations count,
decrement the count when the STA is freed. This does not happen in
AP mode since there is enough time to go through the authenticator
state machine to clear the STA. However, in the current RSN IBSS
implementation, the authenticator state for the STA is freed in a
way that does not allow the state machine to go through the clearing.
To address this, make sure that wpa_free_sta_sm() decrements the
GKeyDoneStations count if the STA happened to be in the process of
GTK rekeying.
CFLAGS += -DCONFIG_RSN_TESTING in .config and rsn_testing=1 in
hostapd.conf can now be used to enable a testing mode that adds
extensions to RSN element. This can be used to check whether
station implementations are incompatible with future extensions
to the RSN element.
The AP code might, currently only in the case of HT40, defer actual
enabling to after a scan. In this case, the wpa_s AP code gets confused.
Add a callback for it to use and make it use it to finish only when the
setup has actually completed.
With appropriate hacks in place this allows using HT40 in P2P mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds the ability to add WPS vendor extensions to an AP (or GO).
They will be added to the WSC IE(s) in Beacon and Probe Response frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of converting back and forth from the string representation,
always use the binary representation internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently hostapd will force HT Mixed Mode if at least one non-GF STA is
associated. This will force _all_ HT transmissions to be protected.
802.11n-2009 doesn't require HT Mixed Mode to be used in case of non-GF
STAs but instead the HT information element contains a flag if non-GF
STAs are present. All STAs are required to protect GF transmissions in
that case. Hence, setting HT Mixed mode if non-GF STAs are present is
superfluous.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This allows driver wrappers to indicate whether the association was
done using Association Request/Response or with Reassociation
Request/Response frames.
os_snprintf() can be a preprocessor macro and according to
C99 (6.10.3 clause 11) the results of having preprocessor directives
inside the macro arguments is undefined.
When using multiple vifs and dynamic vlan tagging is enabled on any
interface, the created AP VLAN interfaces get the BSSID of the first
AP mode interface instead of the BSSID of the corresponding AP mode
interface.
Example:
wlan0 - xx:xx:xx:xx:x0
wlan1 - xx:xx:xx:xx:x1
Assume a STA connects to the AP interface wlan1 and gets a dynamic
VLAN tag 100 assigned by the RADIUS server. Hostapd will create an AP
VLAN interface wlan1.100 but doesn't set an address for this interface
which results in wlan1.100 getting the same address as wlan0:
wlan1.100 - xx:xx:xx:xx:x0
As a result the STA that was moved to wlan1.100 isn't able to finish its
4-way handshake since mac80211 won't pass its frames to wlan1.100 due to
the different address.
To fix this issue make use of the address of the AP interface when
creating an AP VLAN interface.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Add MAC addresses for stations and use wpa_msg instead of printf
methods to make it easier to grep logs and find messages for the
station in question.
Signed-off-by: Ben Greear <greearb@candelatech.com>
In multi BSS setups it wasn't possible to set up an HT BSS in
conjunction with a WEP/TKIP BSS. HT needed to be turned off entirely
to allow WEP/TKIP BSSes to be used.
In order to allow HT BSSes to coexist with non-HT WEP/TKIP BSSes add a
new BSS conf attribute "disable_11n" which disables HT capabilities on a
single BSS by suppressing HT IEs in the beacon and probe response
frames. Furthermore, mark all STAs associated to a WEP/TKIP BSS as
non-HT STAs. The disable_11n parameter is used internally; no new entry
is parsed from hostapd.conf.
This allows a non-HT WEP/TKIP BSS to coexist with a HT BSS without
having to disable HT mode entirely. Nevertheless, all STAs associated to
the WEP/TKIP BSS will only be served as if they were non-HT STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Use l2_packet with Ethernet header included so that the source
address for RRB packets can be forced to be the local BSSID. This
fixes problems where unexpected bridge interface address may end
up getting used and the recipient of the frame dropping it as
unknown R0KH/R1KH.
This is needed to keep kernel and hostapd in sync. In addition,
the obsolete entry in hostapd prevented use of Deauthentication
or Disassociation frame with reason code 6/7 mechanism to indicate
to the STA that there is no association if the STA missed the
broadcast Deauthentication frame for any reason.
The internal pointer to RADIUS client configuration needs to be
updated whenever a new hostapd configuration is loaded. Without
this, freed memory may be dereferenced and this can result in
segmentation faults.
This is needed to allows WPS PBC session overlap detection to work
with drivers that process Probe Request frames internally. This
code is is run in hostapd, but the wpa_supplicant AP mode did not
have call to the hostapd_probe_req_rx() function even though it
registered handlers for hostapd Probe Request RX callbacks.
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07
In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
Add a callback for station's authorized transitions
to allow wpa_supplicant to emit events in DBus.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To enable making state change notifications on the WLAN_STA_AUTHORIZED
flag, introduce ap_sta_set_authorized(), and to reduce use of the flag
itself also add a wrapper for testing the flag: ap_sta_is_authorized().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to call this function after having completed the neighboring
channel scan to figure out whether HT40 can be used and if so, which
channel is the secondary channel.
ieee80211n_supported_ht_capab is called after ieee80211n_check_40mhz in
function hostapd_check_ht_capab. ieee80211n_check_40mhz can return 1 in
a valid scenario where the initialization is completed in a callback. In
this case ieee80211n_supported_ht_capab is skipped and hostapd does not
check the ht capabilities reported by the driver. Fix this issue making
sure ieee80211n_supported_ht_capab gets called.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
If WMM is not disabled explicitly (wmm_enabled=0 in hostapd.conf),
enable WMM automatically whenever HT (ieee80211n) is enabled. Use
the default WMM parameters for AP TX queues and the EDCA parameters
advertised for stations in WMM IE if no overriding values are
included in the configuration.
tdls_prohibit=1 and tdls_prohibit_chan_switch=1 and now be used to
disable use of TDLS or TDLS channel switching in the BSS using
extended cabilities IE as defined in IEEE 802.11z.
Make sure that received management frames are long enough before
processing them. This avoids a potential segmentation fault if a
driver delivers an invalid frame all the way to hostapd.
Previously, only the Configuration Error values were indicated in
WPS-FAIL events. Since those values are defined in the specification
it is not feasible to extend them for indicating other errors. Add
a new error indication value that is internal to wpa_supplicant and
hostapd to allow other errors to be indicated.
Use the new mechanism to indicate if negotiation fails because of
WEP or TKIP-only configurations being disallows by WPS 2.0.
Previously, both NULL and ff:ff:ff:ff:ff:ff addr were used in various
places to indicate default/broadcast keys. Make this more consistent
and useful by defining NULL to mean default key (i.e., used both for
unicast and broadcast) and ff:ff:ff:ff:ff:ff to indicate broadcast
key (i.e., used only with broadcast).
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The frame needs to be sent from an individual (non-group) address,
so drop invalid frames before sending Deauth/Disassoc frames to
not associated STAs.
Getting rid of these inline functions seems to reduce the code size
quite a bit, so convert the most commonly used hostapd driver ops to
function calls.
This is not needed anymore and just makes things more difficult
to understand, so move the remaining function pointers to direct
function calls and get rid of the struct hostapd_driver_ops.
send_eapol, set_key, read_sta_data, sta_clear_stats,
set_radius_acl_auth, set_radius_acl_expire, and set_beacon
to use inline functions instead of extra abstraction.
Commit bf65bc638f started the path to
add this new abstraction for driver operations in AP mode to allow
wpa_supplicant to control AP mode operations. At that point, the
extra abstraction was needed, but it is not needed anymore since
hostapd and wpa_supplicant share the same struct wpa_driver_ops.
Start removing the unneeded abstraction by converting
send_mgmt_frame() to an inline function, hostapd_drv_send_mlme().
This is similar to the design that is used in wpa_supplicant and
that was used in hostapd in the past (hostapd_send_mgmt_frame()
inline function).
On Linux, verify that the kernel entropy pool is capable of providing
strong random data before allowing WPA/WPA2 connection to be
established. If 20 bytes of data cannot be read from /dev/random,
force first two 4-way handshakes to fail while collecting entropy
into the internal pool in hostapd. After that, give up on /dev/random
and allow the AP to function based on the combination of /dev/urandom
and whatever data has been collected into the internal entropy pool.
wlan0: RADIUS No authentication server configured
MEMLEAK[0x999feb8]: len 1040
WPA_TRACE: memleak - START
[3]: ./hostapd(radius_msg_new+0x33) [0x8074f43]
radius_msg_new() ../src/radius/radius.c:117
[4]: ./hostapd() [0x806095e]
ieee802_1x_encapsulate_radius() ../src/ap/ieee802_1x.c:439
ieee802_1x_aaa_send() ../src/ap/ieee802_1x.c:1496
For example, this error occured when I used WPS hostapd without
"eap_server=1" definition in configuration file.
By default, make hostapd and wpa_supplicant maintain an internal
entropy pool that is fed with following information:
hostapd:
- Probe Request frames (timing, RSSI)
- Association events (timing)
- SNonce from Supplicants
wpa_supplicant:
- Scan results (timing, signal/noise)
- Association events (timing)
The internal pool is used to augment the random numbers generated
with the OS mechanism (os_get_random()). While the internal
implementation is not expected to be very strong due to limited
amount of generic (non-platform specific) information to feed the
pool, this may strengthen key derivation on some devices that are
not configured to provide strong random numbers through
os_get_random() (e.g., /dev/urandom on Linux/BSD).
This new mechanism is not supposed to replace proper OS provided
random number generation mechanism. The OS mechanism needs to be
initialized properly (e.g., hw random number generator,
maintaining entropy pool over reboots, etc.) for any of the
security assumptions to hold.
If the os_get_random() is known to provide strong ramdom data (e.g., on
Linux/BSD, the board in question is known to have reliable source of
random data from /dev/urandom), the internal hostapd random pool can be
disabled. This will save some in binary size and CPU use. However, this
should only be considered for builds that are known to be used on
devices that meet the requirements described above. The internal pool
is disabled by adding CONFIG_NO_RANDOM_POOL=y to the .config file.
This commit adds a new wrapper, random_get_bytes(), that is currently
defined to use os_get_random() as is. The places using
random_get_bytes() depend on the returned value being strong random
number, i.e., something that is infeasible for external device to
figure out. These values are used either directly as a key or as
nonces/challenges that are used as input for key derivation or
authentication.
The remaining direct uses of os_get_random() do not need as strong
random numbers to function correctly.
This adds more time for the system entropy pool to be filled before
requesting random data for generating the WPA/WPA2 encryption keys.
This can be helpful especially on embedded devices that do not have
hardware random number generator and may lack good sources of
randomness especially early in the bootup sequence when hostapd is
likely to be started.
GMK and Key Counter are still initialized once in the beginning to
match the RSN Authenticator state machine behavior and to make sure
that the driver does not transmit broadcast frames unencrypted.
However, both GMK (and GTK derived from it) and Key Counter will be
re-initialized when the first station connects and is about to
enter 4-way handshake.
The example GMK-to-GTK derivation described in the IEEE 802.11 standard
is marked informative and there is no protocol reason for following it
since this derivation is done only on the AP/Authenticator and does not
need to match with the Supplicant. Mix in more data into the derivation
process to get more separation from GMK.
There is no point in maintaining two almost identical versions
of this parser. Move WPA IE parser into wpa_common.c similarly
to what was already the case with RSN IE parse.
WPS external Registrars can get confused about multiple UPnP
instances (one per radio) on a dual-concurrent APs. Simplify the
design by sharing a single UPnP state machine for all wireless
interfaces controlled by hostapd. This matches with the previous
changes that made a single command enable WPS functionality on
all interfaces.
This is relatively minimal change to address the sharing of the
state among multiple struct hostapd_data instances. More cleanup
can be done separately to remove unnecessary copies of information.
Commit c3fc47ea8e fixed EAP passthrough
server to allow Logoff/Re-authentication to be used. However, it
broke EAP standalone server while doing that. Fix this by reverting
the earlier fix and by clearing the EAP Identity information in the
EAP server code whenever an EAPOL-Start or EAPOL-Logoff packet is
received.
These are not used by any driver wrapper, i.e., only the four
data queues (BK, BE, VI, VO) are configurable. Better remove these
so that there is no confusion about being able to configure
something additional.
This is needed to avoid problems with other applications setting and
leaving the interface to IF_OPER_DORMANT state. In AP mode, the interface
is ready immediately after the keys are set, so we better make sure the
DORMANT state does not prevent normal operations after that.
Some driver wrappers may end up indicating a disassociation or
deauthentication event without the address of the station, e.g.,
based on a previous non-AP mode event. Avoid crashing hostapd
by verifying that the require address parameter is available in
the event before processing it.
This test command is supposed to change the WPS version number in all
places immediately, so make sure that the IEs used in management
frames get updated immediately.
The P2P group component is now tracking of associated stations
in the group and the Group Limit bit in the Group Capabilities
is updated based on whether there is room for new clients in
the group.
The AP operation with wpa_supplicant requires an additional callback
to get the needed event information from hostapd side so that
wpa_msg() can be called for wpa_s->parent if needed.
When a single hostapd process is controlling multiple interfaces,
apply the received or auto-generated configuration changes to all
interfaces that have enabled WPS.
When the same hostapd process is controlling multiple interfaces,
apply WPS commands (push button, add PIN, change AP PIN) to all
interfaces that are configured to use WPS.
Commit 3379a3a795 added a direct
iface->for_each_interface use without verification whether the
function is available. This works with hostapd, but not
wpa_supplicant (which crashes on segfault).
The previous implementation ended up incorrectly assuming that all
40 MHz use cases have secondary channel above the primary one. Fix this
by properly masking the secondary channel offset field and checking its
value.
This is needed to update the pointers maintained within WPS code
to use the new configuration data instead of maintaining pointers
to the old configuration which will be freed. This fixes strings in
UPnP discovery after reconfig (they used to be random freed memory..).
This seems to be the easiest way of making sure the Config Methods
value is compliant with the WSC 2.0 specification without having
to modify the configuration file. However, this will only add the
virtual flag, so the configuration files should really be updated
to specify values that match the AP design.
WPS 2.0 mandates the AP to include WPS IE in (Re)Association Response
if the matching (Re)Association Request included WPS IE. Provide the
needed WPS IE information to the driver_ops API for drivers that
process association frames internally.
Note: This modifies the driver_ops API by adding a new argument to
set_ap_wps_ie().
The Beacon frame must include UUID-E and RF Bands attributes when
in active PBC mode to allow stations to figure out that two BSSes in
PBC mode is not a PBC session overlap.
When generating the UUID based on MAC address, share the same UUID
with all interfaces. This fixes a potential issue with concurrent
dualband APs where the UUID needs to be same for PBC to work properly.
This can happen, e.g., when a P2P client connects to a P2P group
using the infrastructure WLAN interface instead of P2P group
interface. In that case, the P2P client may behave as if the GO
would be a P2P Manager WLAN AP.
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
While this is not strictly speaking required based on dynamic
configuration (i.e., dot11ShortPreambleOptionImplemented is static
value based on implementation, not runtime configuration), it is better
to follow local configuration parameter for short preamble in addition
to the associated station capabilities.
This function is not really needed in case of drivers that build the
HT IEs internally. However, since this can get called if ieee80211n=1
is set in hostapd.conf, we better not segfault even if the driver
does not provide hw info (hapd->iface->current_mode == NULL).
Commit 5a1cc30f1a added code that was
assuming CONFIG_WPS_UPNP is enabled whenever CONFIG_WPS is. Fix this
by making the UPnP calls conditional on CONFIG_WPS_UPNP define.
hostapd simply used its own STBC configuration in the STA's HT caps. This
resulted in TX STBC being used for STAs not supporting RX STBC, which in
turn resulted in the STA not receiving anything.
Fix this by handling the STBC flags in the same way mac80211 does. Mask
out RX STBC if we don't support TX STBC and vice versa.
Tested only with the nl80211 driver and a STBC incapable STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
A new hostapd_cli command, wps_ap_pin, can now be used to manage
AP PIN at runtime. This can be used to generate a random AP PIN and
to only enable the AP PIN for short period (e.g., based on user
action on the AP device). Use of random AP PIN that is only enabled
for short duration is highly recommended to avoid security issues
with a static AP PIN.
As a compromise between usability and security, do not disable
AP PIN permanently based on failed PIN validations. Instead, go to
AP Setup Locked state for increasing amount of time between each
failure to slow down brute force attacks against the AP PIN.
This avoids problems with some external Registrars that may try
to use the same PIN multiple times without user input. Now, the
user will still be able to fix the PIN and try again later while
a real attack is delayed enough to make it impractical.
In theory, this should not really be needed, but Windows 7 uses
Registrar mode to probe AP's WPS capabilities before trying to use
Enrollee and fails if the AP does not allow that probing to happen.
This allows the AP to start as an Enrollee and send M1, but refuse
to continue beyond that (M3 will not be sent if AP PIN is not known).
This makes it easier (and a bit faster) to handle multiple local
radios with FT. There is no need to depend on l2_packet in that
case since the frame can be delivered as a direct function call.
If the station does not include WSC IE in Association Request, it
is marked with WLAN_STA_MAYBE_WPS flag. We can update that to
WLAN_STA_WPS if the station uses either of the WPS identity strings.
This enables some workarounds for WPS stations.
The pairwise cipher field is supposed to be little endian, but the
message building functions did not swap the bytes on big endian
hosts while the message processing functions did. Fix this by using
little endian byte order in both places.
Some frequent debug prints are of limited use and make debug output
difficult to read. Make them use a new debug level so that -dd
provides more readable output (-ddd can now be used to enable
the excessive debug prints).
Some of the driver wrappers need to get set_ieee8021x() call before
they can configure keys. Reorder the operations in the reloading
of configuration case to match with that expectation.
If the associating station indicates that it is intents to use WPS
by including WPS IE in (Re)Association Request frame, include WPS IE
in (Re)Association Response frame.
Vendor-specific IEs are supposed to be in the end of the frame, so move
WMM into the end of Beacon, Probe Response, and (Re)Association Response
frames. In addition, move HT IEs to be later in (Re)Association
Response to match the correct order.
hostapd_eid_wpa() adds multiple IEs and the end result may not always be
correct. If WPA is enabled, WPA IE (vendor-specific) gets added in the
middle of the frame and not in the end. This would require a larger
change to spliut the IEs from WPA module into separate locations when
constructing Beacon and Probe Response frames. This is not yet addressed.
Commit c02d52b405 removed direct calls
to the WPA authenticator, but the change here was incorrect.
EAPOL_SM_USES_WPA was supposed to be set based on sta->wpa_sm being
set, i.e., no need to check for PMKSA entries for that.
While this could potentially change EAPOL Key TX state machine behavior,
no clear problems have been identified so far. Anyway, better fix this
to get the correct flags set for EAPOL authenticator state machine.
When using WPS, we may end up here if the STA manages to re-associate
without the previous STA entry getting removed. Consequently, we need to
make sure that the WPA state machines gets initialized properly at this
point.
There are no subdirectories in any of these directories or plans
for adding ones. As such, there is no point in running the loop
that does not do anything and can cause problems with some shells.
Both the wildcard VLAN entry and the statically configured VLAN
interfaces should behave in the same way. Initializing the
full dynamic VLAN code before adding the statically configured VLAN
interfaces allows the same processing to be applied to both statically
and dynamically added VLAN interface (i.e., also the statically
configured ones will be added to a bridge).
The WPS IE was overriding the WPA/RSN IE in driver based MLME case
(hostapd_notif_assoc), but the MLME code here was not using WPS IE
correctly, i.e., it allowed the WPA/RSN IE override the operation.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
hostapd does not implement UAPSD functionality. However, if U-APSD
functionality is implemented outside hostapd, add support to advertise
the functionality in beacon.
Signed-off-by: yogeshp@marvell.com
ANonce, SNonce, R0KH-ID, and R1KH-ID must match with the values
used in the previous FT authentication sequence message per
IEEE Std 802.11r-2008, 11A.8.4.
We do not have any keys set at this point so there is no point in
adding the MIC. In addition, IEEE Std 802.11r-2008, 11A.4.2
describes this frame to have MIC IE count of 0 and MIC of 0.
IEEE Std 802.11r-2008, 11A.4.2 describes FT initial mobility domain
association in an RSN to include PMKR1Name in the PMKID-List field
in RSN IE in messages 2/4 and 3/4. This makes the RSN IE not be
bitwise identical with the values used in Beacon, Probe Response,
(Re)association Request frames.
The previous versions of wpa_supplicant and hostapd did not add the
PMKR1Name value in EAPOL-Key frame and did not accept it if added
(due to bitwise comparison of RSN IEs). This commit fixes the
implementation to be compliant with the standard by adding the
PMKR1Name value into EAPOL-Key messages during FT 4-Way Handshake and
by verifying that the received value matches with the value derived
locally.
This breaks interoperability with previous wpa_supplicant/hostapd
versions.
Running hostapd and wpa_supplicant on the same interface at the same
time is not expected to work, but it should not cause hostapd to crash.
Ignore station mode association events (no addr field) to avoid this.
IF WPA/RSN parameters were changed or WPA/RSN was disabled, the
WPA/RSN IE in Beacon/Probe Response frames was only update with
set_beacon(). We need to do this with set_generic_elem(), too, to
work with all driver wrappers.
Call ieee802_11_set_beacon() in addition to set_ap_wps_ie() when
processing WPS IE updates. This is needed with drivers that use
set_beacon() instead of set_ap_wps_ie() (i.e., nl80211).
It turns out that this is needed for both FT-over-DS and FT-over-air
when using mac80211, so it looks easiest to just unconditionally
re-configure the keys after reassociation when FT is used.
This is needed to allow reassociation processing to skip 4-way handshake
when FT-over-DS is used with an AP that has a previous association state
with the STA.
This seems to be needed at least with mac80211 when a STA is using
FT-over-DS to reassociate back to the AP when the AP still has the
previous association state.
This makes the call simpler for driver wrappers since there is no need
to parse the IEs anymore before indicating association. In addition,
this allows association processing to be extended to use other IEs
in the future.
IGTK get_seqnum needs to be skipped in the same way as GTK one when
rekeying group keys. Previously, the old PN value (the one from the
previous key) was indicated and that resulted in MMIE replay detection
at the station.
Must update sm->pairwise when fetching PMK-R1 SA.
Add a workaround for drivers that cannot set keys before association
(e.g., cfg80211/mac80211): retry PTK configuration after association.
This is needed to fix PTK derivation to use correct length. Previously,
64-octet PTK may have been derived if the authenticator did not already
have a STA entry. Now, the correct pairwise cipher suite is learned when
then PMK-R1 SA is received.
With this patch, a client gets kicked out of the last BSS it was
attached to, when it is associating to a different one.
While mac80211 does allow a station to be present on multiple bss
interfaces, this does seem to cause problems both for the stack
and for hostapd.
This patch allows the nl80211 driver to create its own per-bss context
and pass it to the drv_priv pointer of the hostapd bss state.
With this and the following patch, stations can associate to and switch
between multiple BSS interfaces of a single wiphy.
This obsoletes a few instances of passing ifname to a callback, those
can be removed in a separate patch.
It might also be useful to move more fields from the driver data to the
per-bss data structure in the future.
This patch moves the authentication server setup before
IEEE 802.1X initialization. It's because 802.1X already
needs to have a valid SSL context.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
wpa_sm_step() could theoretically free the statemachine, but it does
not do it in this particular case. Anyway, the code can be cleaned to
verify whether the state machine data is still available after the
wpa_sm_step() call.
wmm_ac_??_cw{min,max} parameters are in log form
When the wme_ac_??_cw{min,max} parameters aren't specified in
hostapd.conf, hostapd uses an incorrect set of default values, as the
defaults are in 2^x-1 form instead of in log form. This patch changes
them over to the expected log form.
The three existing enums were already depending on using the same
values in couple of places and it is just simpler to standardize on
one of these to avoid need for mapping between different enums for
the exact same thing.
Most of this file was already moved into wpa_supplicant/scan.c and
we can remove the file completely by having couple of small helper
functions copied to the remaining users outside core wpa_supplicant
code.
This allows the driver interface to be deinitialized before
struct hostapd_data instance gets freed. This needs to be done so
that the driver wrapper does not maintain a context pointer to
freed memory.
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
This code can be shared by both hostapd and wpa_supplicant and this
is an initial step in getting the generic code moved to be under the
src directories. Couple of generic files still remain under the
hostapd directory due to direct dependencies to files there. Once the
dependencies have been removed, they will also be moved to the src/ap
directory to allow wpa_supplicant to be built without requiring anything
from the hostapd directory.
