Fast BSS Transition requires related APs operating in the same mobility
domain. Therefore, we can check whether the local managed BSS is
operating the same mobility domain before sending multicast/unicast
messages to it. This reduces unnecessary load from having to allocate
queued messages for interfaces that cannot have valid data.
Signed-off-by: Jinglin Wang <bryanwang@synology.com>
Signed-off-by: MinHong Wang <minhongw@synology.com>
This makes it easier to figure out how frames are delivered directly
between BSSs operated within a single hostapd process.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add new messages to the end of the l2_oui_queue instead of inserting
them at the beginning so that the dl_list_for_each_safe() iteration in
hostapd_oui_deliver_later() goes through the messages in the same order
they were originally queued.
Signed-off-by: Jouni Malinen <j@w1.fi>
When using FT wildcard feature, the inter-AP protocol will send
broadcast messages to discover related APs.
For example,
12/6 16:24:43 FT: Send PMK-R1 pull request to remote R0KH address
ff:ff:ff:ff:ff:ff
12/6 16:24:43 FT: Send out sequence number request to
ff:ff:ff:ff:ff:ff
If you have multiple interfaces/BSSs in a single hostapd process,
hostapd_wpa_auth_oui_iter() returned 1 after the first interface was
processed. Iteration in for_each_interface() will be stopped since it
gets a non-zero return value from hostapd_wpa_auth_oui_iter().
Even worse, the packet will not be sent to ethernet because
for_each_interface() returns non-zero value. hostapd_wpa_auth_send_oui()
will then return data_len immediately.
To prevent this, hostapd_wpa_auth_oui_iter() should not return 1 after
any successful transmission to other interfaces, if the dst_addr of
packet is a multicast address.
Signed-off-by: Jinglin Wang <bryanwang@synology.com>
Signed-off-by: MinHong Wang <minhongw@synology.com>
ignore_broadcast_ssid=1 (or 2) were practically ignored if the Probe
Request frame included the SSID List or Short SSID List elements. Fix
this by requiring exact SSID match whenever ignore_broadcast_ssid is in
use regardless how SSID parameters are set in the Probe Request frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
According to IEEE P802.11ax/D6.0, 11.1.4.3.4 (Criteria for sending a
response), AP should answer Probe Request frames if either SSID or Short
SSID matches. Implement this part of the Short SSID use for the BSS (the
collocated 6 GHz BSS case is not covered in this commit).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This can be used in the future to implement support for RNR and scanning
extensions using a shorter field for the SSID.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We use the wired driver for wired port authentication with a slight
extension to add the port into a bridge upon successful authentication
and to remove it from the bridge when the session terminates.
Our expectation was that the Session-Timeout configuration at the RADIUS
server is respected, i.e. the session is terminated and would need
re-authentication - like it is working for WLAN sessions over the
nl80211 driver. Alas, it turned out the session is not terminated with
the wired driver.
It turned out that when ap_handle_session_timer() is executed, the
sta->flags of the wired port has only the WLAN_STA_AUTHORIZED bit set.
The WLAN_STA_AUTH bit, which is used to check whether the STA needs to
be de-authenticated, is missing.
Extend the check for any of the WLAN_STA_(AUTH | ASSOC | AUTHORIZED)
bits to solve this issue with the wired driver. That should not have any
side-effect for the WLAN cases since WLAN_STA_AUTH is expected to always
be set for those when there is an ongoing session and separate checks
for ASSOC and AUTHORIZED don't change this.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
This lets one know the current neighbor list, and could be used
to populate the neighbor list of other hostapd processes.
For instance:
$ hostapd_cli -i vap0001 show_neighbor
04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
$ hostapd_cli -i vap0000 set_neighbor 04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
OK
$ hostapd_cli -i vap0000 show_neighbor
04:f0:21:1e:ae:b0 ssid=04f0211eaeb0af190000802809 nr=04f0211eaeb0af1900008028090603022a00
04:f0:21:c3:b2:b0 ssid=04f021c3b2b0af190000802809 nr=04f021c3b2b0af1900008028090603022a00
Signed-off-by: Ben Greear <greearb@candelatech.com>
WPS_EVENT_CANCEL is added to indicate cancellation of a WPS operation
for any reason in hostapd/wpa_supplicant.
WPS_EVENT_PIN_ACTIVE is added to indicate when a PIN operation is
triggered in wpa_supplicant.
Signed-off-by: Veli Demirel <veli.demirel@airties.com>
Signed-off-by: Bilal Hatipoglu <bilal.hatipoglu@airties.com>
EAPOL-Key message 1/4 without PMKID KDE was sent with 22 bytes of stray
data following a zero length key data field. These 22 bytes happens to
be the exact size of an PMKID KDE. Strip these trailing bytes by
checking whether a PMKID is available and adjust pmkid_len to 0 if not.
This was seen for example in capture files created by hwsim test case
suite_b_192 but code modified to handle also the other cases without
PMKID (Suite B no-KCK, FILS without PMKID available, SAE without PMKID
available).
Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sony.com>
Use op_class to derive channel width for the operating channel when
op_class is configured by the user in both fixed channel and ACS cases.
We can avoid using ht_capab field to derive channel width especially in
the 6 GHz band in which only HE is supported.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to exclude non-PSC 6 GHz channels from the input frequency
list to ACS. The new acs_exclude_6ghz_non_psc=1 parameter can be used by
6 GHz only APs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The channel numbers are duplicated between 2.4 GHz / 5 GHz bands and 6
GHz band. Hence, add support to configure a list of frequencies to ACS
(freqlist) instead of a list of channel numbers (chanlist). Also, both 5
GHz and 6 GHz channels are referred by HOSTAPD_MODE_IEEE80211A. The 6
GHz channels alone can be configured by using both mode and frequency
list.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using the channel parameter for validating allowed channel combinations
is not scalable to add 6 GHz support in the future since channel numbers
are duplicated between 2.4 GHz / 5 GHz bands and 6 GHz band. Hence use
frequency field for all channel combination validation steps done before
starting AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
After receiving ACS offload results, select the current hw_mode based on
the frequency selected by the ACS algorithm. The current hw_mode will be
further used during other validation steps such as HT capability
validations, DFS validation, etc.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Using channel field while starting AP will cause issues with the new
6GHz band as the channel numbers are duplicated between the different
bands. Populate iface->freq before starting AP so that it can be used
instead of the channel number for all validations that need to be done
while starting AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Replace channel fields with frequency fields in ACS completed event
interface from the driver layer. Use
QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY attributes if the driver
includes them in the QCA_NL80211_VENDOR_SUBCMD_DO_ACS event, otherwise
use QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL and
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL attributes to maintain
backwards compatibility with old drivers.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to stored in
a separate hw_features set (but with same mode HOSTAPD_MODE_IEEE80211A)
due to possibility of different HE capabilities being available between
the 5 GHz and 6 GHz bands.
Search through all hw_features sets whose mode is same as the input mode
while finding channel corresponding to the input frequency in
hw_get_channel_freq().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The 5 GHz channels are stored in one hw_features set with mode
HOSTAPD_MODE_IEEE80211A while the 6 GHz channels will need to stored in
a separate hw_features set (but with same mode HOSTAPD_MODE_IEEE80211A)
due to possibility of different HE capabilities being available between
the 5 GHz and 6 GHz bands.
Iterate through all hw_features sets and populate channels from all
hw_features sets whose hardware mode is matching the configured hardware
mode while preparing the channel list for ACS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is mainly for testing purposes to be able to check which groups
a STA reports as having been rejected when using SAE H2E.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The netRole enum is more generic and can be extended to include new
roles (e.g., Configurator) more easily.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new hostapd configuration parameter rsnxe_override_eapol=<hexdump>
can be used to override RSNXE value in EAPOL-Key msg 3/4 for testing
purposes.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, this case was ignored silently in AP mode. While that could
be a reasonable approach for an unexpected condition, it would be fine
to reject this case explicitly as well. This makes it somewhat easier to
test unexpected SAE H2E vs. looping behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
check_sae_rejected_groups() returns 1, not -1, in case an enabled group
is rejected. The previous check for < 0 could not have ever triggered.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, this case was ignored silently in AP mode. While that could
be a reasonable approach for an unexpected condition, it would be fine
to reject this case explicitly as well. This makes it somewhat easier to
test unexpected SAE H2E vs. looping behavior.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
freq_list is built in allocated heap memory and it needs to be freed
before returning from this function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Clean up do_acs interface to not pass ch_list to drivers as the same
information is available in freq_list. The channel numbers are
duplicated between 2.4 GHz and 5 GHz bands and the 6 GHz band. So, use
the QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST to populate only 2.4 GHz and 5 GHz
channels to ensure backwards compatibility with old drivers which do not
have support to decode the newer QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST
attribute.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Skip DFS checks and CAC operation for 6 GHz channels. AFC checks
will be added for 6 GHz channels later.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
HT capability check is not required when starting AP on 6 GHz band as
only HE operation mode is allowed in the 6 GHz band.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends hostapd and wpa_supplicant DPP implementation to allow the
bootstrapping URI to be generated for and parsed from an NFC Tag with an
NFC URI Record. This is similar to the way the bootstrapping URI is used
with QR Code for unidirectional authentication.
The DPP_BOOTSTRAP_GEN command uses "type=nfc-uri" to request the URI to
be assigned for NFC URI Record. In practice, the URI is generated
identically to the QR Code case, but the internal entry maintains the
NFC-URI type.
A new command "DPP_NFC_URI <uri>" can now be used to parse the URI read
from an NFC Tag with the NFC URI Record. This is similar to the
DPP_QR_CODE command.
Other commands (mainly, DPP_LISTEN and DPP_AUTH_INIT) are used for NFC
URI in the same way as they are used for QR Code.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Commit 844dfeb804 ("QCA vendor command support to set band to driver")
added a vendor command to pass 'SET setband' command information to the
driver in wpa_supplicant. Add similar changes to hostapd control
interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, nonzero sae_h2e parameter values were used to perform SAE
H2E specific operations (deriving PT, adding RSNXE, adding H2E-only BSS
membership selector) in AP mode even if SAE was not enabled for the
network. This could result in unexpected behavior if sae_pwe=1 or
sae_pwe=2 were set in the configuration. Fix this by making the SAE
operations conditional on SAE being actually enabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The WMM TSPEC processor used the input buffer for processing the request
and building the response. This was fine for the FT case, but for the
WMM Action frame case, the input buffer is marked const, so it should
not really be modified. This modification could not really cause any
noticeable harm, but it can result in error reports from fuzzing and
potentially even from some static analyzers.
Fix this by marking the input arguments const more consistently (the
parsed IE was able to drop the const) and copy the const input data to a
temporary buffer for processing and modification instead of allowing the
input data to be modified.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=19050
Signed-off-by: Jouni Malinen <j@w1.fi>
Update center frequency and center frequency2's DFS channel status in
VHT80+80 mode. Otherwise it will cause AP failed to start on a DFS
channel.
Tested: qca9984 with firmware ver 10.4-3.10-00047
Signed-off-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
wpa_validate_wpa_ie() was already extended to cover these cases with
WPA_INVALID_PMKID return value, but hostapd_notif_assoc() did not have
code for mapping this into the appropriate status code
(STATUS_INVALID_PMKID) and ended up using the default
(WLAN_STATUS_INVALID_IE) instead. This caused AP SME-in-driver cases
returning incorrect status code when the AP did not have a matching
PMKSA cache entry. This could result in unexpected station behavior
where the station could continue trying to use a PMKSA cache entry that
the AP does not have and not being able to recover this.
Fix this by adding the previously missed mapping of validation errors to
status/reason codes.
Fixes: 567da5bbd0 ("DPP: Add new AKM")
Fixes: 458d8984de ("SAE: Reject request with mismatching PMKID (no PMKSA cache entry)")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Addi STA node details in AP through QCA vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE vendor when processing FT
protocol roaming.
Signed-off-by: Shiva Sankar Gajula <sgajula@codeaurora.org>
If hostapd had existing STA SAE state, e.g., from a previously completed
SAE authentication, a new start of a separate SAE authentication (i.e.,
receiving of a new SAE commit) ended up using some of the previous
state. This is problematic for determining whether to H2E vs. looping
since the STA is allowed (even if not really expected to) to change
between these two alternatives. This could result in trying to use H2E
when STA was using looping to derive PWE and that would result in SAE
confirm failing.
Fix this by determining whether to use H2E or looping for the restarted
authentication based on the Status Code in the new SAE commit message
instead of previously cached state information.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The IE minimum length determination in hostapd_eid_ext_capab() was not
fully up to date with the hostapd_ext_capab_byte() conditions. This
could result in omitting some of the capability octets depending on
configuration. Fix this by adding the missing conditions.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Protect RSNXE, if present, in FT Reassociation Request/Response frames.
This is needed for SAE H2E with FT.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use a single struct definition and a single shared implementation for
parsing EAPOL-Key KDEs and IEs instead of maintaining more or less
identical functionality separately for wpa_supplicant and hostapd.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If a STA indicates support for SAE H2E in RSNXE and H2E is enabled in
the AP configuration, require H2E to be used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the STA advertises RSN Extension element, it has to be advertised
consistently in the unprotected ((Re)Association Request) and protected
(EAPOL-Key msg 2/4) frames. Verify that this is the case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to be able to compare the received RSNXE to a protected
version in EAPOL-Key msg 2/4.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When operating on the 6 GHz band, add 6 GHz Operation Information inside
the HE Operation element and don't publish HT/VHT IEs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Replace HOSTAPD_MODE_IEEE80211AX mode checks with is_6ghz_op_class()
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
If hostapd is configured to enable only the hash-to-element version of
SAE PWE derivation (sae_pwe=1), advertise BSS membership selector to
indicate this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This parameter can be used to specify which PWE derivation mechanism(s)
is enabled. This commit is only introducing the new parameter; actual
use of it will be address in separate commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd is by default waiting STA to send SAE Confirm before sending the
SAE Confirm. This can now be configured with sae_confirm_immediate=1
resulting in hostapd sending out SAE Confirm immediately after sending
SAE Commit.
These are the two different message sequences:
sae_confirm_immediate=0
STA->AP: SAE Commit
AP->STA: SAE Commit
STA->AP: SAE Confirm
AP->STA: SAE Confirm
STA->AP: Association Request
AP->STA: Association Response
sae_confirm_immediate=1
STA->AP: SAE Commit
AP->STA: SAE Commit
AP->STA: SAE Confirm
STA->AP: SAE Confirm
STA->AP: Association Request
AP->STA: Association Response
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add two new configuration parameters for hostapd:
enable_edmg: Enable EDMG capability for AP mode in the 60 GHz band
edmg_channel: Configure channel bonding for AP mode in the 60 GHz band
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Process all received DPP Configuration Object attributes from
Configuration Result in Enrollee STA case. If wpa_supplicant is
configured to add networks automatically, this results in one network
being added for each included Configuration Object.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
PTKINITNEGOTIATING in the WPA state machine calls wpa_send_eapol() and
hands over the GTK instead of the PTK keyid.
Besides a confusing debug message this does not have any negative side
effects: The variable is only set to a wrong value when using WPA2 but
then it's not used.
With this patch PTKINITNEGOTIATING sets the PTK keyid unconditionally to
zero for EAPOL-Key msg 3/4 and differentiates more obviously between GTK
and PTK keyids.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
When we set "channel=0" in hostapd.conf to enable ACS function, and set
a wrong channel list, e.g., chanlist=222-999 on purpose, hostapd would
still start ACS process to compute the ideal channel, even when there
are no available channels with such configuration.
Though there is no problem since hostapd fails to initialize interface,
it spends time going through the scan and the debug log entries may make
it more difficult to tell what was behind the failure.
Thus, check if there are any available channels in acs_request_scan(),
and return -1 if no available channel, then it will fail at acs_init(),
without doing ACS computation. It will show the following in the log:
Could not select hw_mode and channel. (-3)
wlan0: interface state UNINITIALIZED->DISABLED
Then we can know the setting is incorrect already in
hostapd_select_hw_mode(), instead of waiting for scan callback function
to know if the setting is ok for ACS or not. This can save time and help
to tell if the setting is correct at the initial function at the first.
This will also allow the ENABLE control interface command to return FAIL
when adding an interface dynamically.
Signed-off-by: Neo Jou <neojou@gmail.com>
The new hostapd and wpa_supplicant configuration parameters dpp_name and
dpp_mud_url can now be used to set a specific name and MUD URL for the
Enrollee to use in the Configuration Request. dpp_name replaces the
previously hardcoded "Test" string (which is still the default if an
explicit configuration entry is not included). dpp_mud_url can
optionally be used to add a MUD URL to describe the Enrollee device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use the same rules for dropping driver notifications for Data frames
from unassociated stations as were added for Management frame reception.
This results in more consistent behavior in sending out Deauthentication
frames with Reason Code 6/7.
This case was already checking for unexpected multicast addresses, so
there was no issue for the PMF protections for unexpected disconnection.
Anyway, better avoid unnecessary Deauthentication frames consistently.
Signed-off-by: Jouni Malinen <j@w1.fi>
A new argument to the DPP_AUTH_INIT command (conn_status=1) can now be
used to set Configurator to request a station Enrollee to report
connection result after a successfully completed provisioning step. If
the peer supports this, the DPP-CONF-SENT event indicates this with a
new argument (wait_conn_status=1) and the Configurator remains waiting
for the connection result for up to 16 seconds.
Once the Enrollee reports the result, a new DPP-CONN-STATUS-RESULT event
is generated with arguments result, ssid, and channel_list indicating
what the Enrollee reported. result=0 means success while non-zero codes
are for various error cases as specified in the DPP tech spec. If no
report is received from the Enrollee, the event with "timeout" argument
is generated locally.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such it has not been
maintained nor is there any expectation of the withdrawn trial-use
recommended practice to be maintained in the future. Furthermore,
implementation of IAPP in hostapd was not complete, i.e., only parts of
the recommended practice were included. The main item of some real use
long time ago was the Layer 2 Update frame to update bridges when a STA
roams within an ESS, but that functionality has, in practice, been moved
to kernel drivers to provide better integration with the networking
stack.
Signed-off-by: Jouni Malinen <j@w1.fi>
Do not process any received Management frames with unexpected/invalid SA
so that we do not add any state for unexpected STA addresses or end up
sending out frames to unexpected destination. This prevents unexpected
sequences where an unprotected frame might end up causing the AP to send
out a response to another device and that other device processing the
unexpected response.
In particular, this prevents some potential denial of service cases
where the unexpected response frame from the AP might result in a
connected station dropping its association.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows us to send the OBSS PD settings to the kernel, such that the
driver can propagate them to the hardware/firmware.
Signed-off-by: John Crispin <john@phrozen.org>
Hardcode this to be defined and remove the separate build options for
PMF since this functionality is needed with large number of newer
protocol extensions and is also something that should be enabled in all
WPA2/WPA3 networks.
Signed-off-by: Jouni Malinen <j@w1.fi>
With DFS offloaded to the driver, hostapd state and CAC info was not
updated in DFS-CAC-START event, so STATUS output showed wrong info. Fix
this by updating the CAC related state when processing the driver event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Allow the previously hardcoded maximum numbers of EAP message rounds to
be configured in hostapd EAP server. This can be used, e.g., to increase
the default limits if very large X.509 certificates are used for EAP
authentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
Set the max value of optional bytes inside the data structure. This
requires us to calculate the actually used size when copying the
HE capabilities and generating the IE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
OSEN element was getting added both through the Authenticator IEs
(before some non-vendor elements) and separately at the end of the
frames with other vendor elements. Fix this by removing the separate
addition of the OSEN element and by moving the Authenticator IE addition
for OSEN to match the design used with WPA so that the vendor element
gets added in the proper place in the sequence of IEs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Even though the station is not supposed to include Hotspot 2.0
Indication element in the Association Request frame when connecting to
the open OSU BSS, some station devices seem to do so. With the strict
PMF-required-with-Hotspot-2.0-R2 interpretation, such connection
attempts were rejected. Relax this to only perform the PMF check if the
local AP configuration has PMF enabled, i.e., for the production BSS.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Merge the separate debug print with the text name of the EAP code into
the same debug line with the numerical value to clean up debug log.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use struct eap_config as-is within RADIUS server to avoid having to
duplicate all the configuration variables at each interface. This
continues cleanup on struct eap_config duplication in hostapd.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration parameter eap_teap_id can be used to
configure the expected behavior for used identity type.
Signed-off-by: Jouni Malinen <j@w1.fi>
Use struct eap_config as-is within struct eap_sm and EAPOL authenticator
to avoid having to duplicate all the configuration variables at each
interface. Split the couple of session specific variables into a
separate struct to allow a single const struct eap_config to be used.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new eap_teap_separate_result=1 hostapd configuration parameter can
be used to test TEAP exchange where the Intermediate-Result TLV and
Crypto-Binding TLV are send in one message exchange while the Result TLV
exchange in done after that in a separate message exchange.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new hostapd configuration option eap_sim_id can now be used to
disable use of pseudonym and/or fast reauthentication with EAP-SIM,
EAP-AKA, and EAP-AKA'.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add an SQLite table for defining per station MAC address version of
radius_auth_req_attr/radius_acct_req_attr information. Create the
necessary table and index where this doesn't exist. Select attributes
from the table keyed by station MAC address and request type (auth or
acct), parse and apply to a RADIUS message.
Add radius_req_attr_sqlite hostapd config option for SQLite database
file. Open/close RADIUS attribute database for a lifetime of a BSS and
invoke functions to add extra attributes during RADIUS auth and
accounting request generation.
Signed-off-by: Terry Burton <tez@terryburton.co.uk>
We will want to parse RADIUS attributes in config file format when
retrieving them from an SQLite database.
Signed-off-by: Terry Burton <tez@terryburton.co.uk>
The new "wpa" and "AKMSuiteSelector" entries in hostapd "STA <addr>"
control interface output can be used to determine the negotiated WPA/RSN
protocol and AKM suite of an associated station.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd EAP server can now be configured with two separate server
certificates/keys to enable parallel operations using both RSA and ECC
public keys. The server will pick which one to use based on the client
preferences for the cipher suite (in the TLS ClientHello message). It
should be noted that number of deployed EAP peer implementations do not
filter out the cipher suite list based on their local configuration and
as such, configuration of alternative types of certificates on the
server may result in interoperability issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support for a new EAP method: EAP-TEAP (Tunnel Extensible
Authentication Protocol). This should be considered experimental since
RFC 7170 has number of conflicting statements and missing details to
allow unambiguous interpretation. As such, there may be interoperability
issues with other implementations and this version should not be
deployed for production purposes until those unclear areas are resolved.
This does not yet support use of NewSessionTicket message to deliver a
new PAC (either in the server or peer implementation). In other words,
only the in-tunnel distribution of PAC-Opaque is supported for now. Use
of the NewSessionTicket mechanism would require TLS library support to
allow arbitrary data to be specified as the contents of the message.
Signed-off-by: Jouni Malinen <j@w1.fi>
The HE capabilities are no longer per PHY but per iftype on this
specific PHY. It is therefore no longer enough to just parse the AP
capabilities.
The he_capabilities are now duplicated to store all information for
IEEE80211_MODE_* which hostap cares about. The nl80211 driver fills in
this information when the iftype supports HE. The rest of the code still
only uses the IEEE80211_HE_AP portion but can be extended later to also
use other HE capabilities.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Declare the variable only once and reuse it instead of openning
unneeded scopes.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The the mask for PPE threshold present in the HE phy capability byte 6 is
0x80 and not 0x6. This incorrect mask breaks the length calculation and as
result the acceptance of the HE capabilities for STAs which either:
* don't have the PPE threshold present bit set AND the Codebook Size={7,5}
MU Feedback or the Triggered SU Beamforming feedback bit set
* do have the PPE threshold present set AND neither the Codebook Size={7,5}
MU Feedback nor the Triggered SU Beamforming feedback bit set
Fixes: 8f5fc369e2 ("HE: Fix HE Capabilities element variable length encoding")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
The same len variable can be used for both needs within
ieee802_1x_get_keys() to avoid compiler warning about use of shadowed
variable.
Fixes: 0ee6885dae ("macsec: Store EAP-Key-Name as eapSessionId")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This implements the required functionality in hostapd to facilitate OWE
connection with the AP SME-in-driver cases. Stations can either send DH
IE or PMKID (in RSNE) (or both) in Association Request frame during the
OWE handshake. The drivers that use this offload mechanism do not
interpret this information and instead, pass the same to hostapd for
further processing. hostapd will either validate the PMKID obtained from
the STA or generate DH IE and further indicate the same to the driver.
The driver further sends this information in the Association Response
frame.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
Signed-off-by: Liangwei Dong <liangwei@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is safer to maintain the old EAPOL version (2) in EAPOL frames that
are not related to MACsec and only update the version to 3 for the
MACsec specific cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
External auth status to the driver includes the PMKID derived as part of
SAE authentication, but this is not valid if PMKSA caching is disabled.
Drivers might not be expecting PMKID when it is not valid. Do not send
the PMKID to the driver in such cases.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
In case the current channel has regulatory WMM limitations, take them
into account when filling the WMM element. Also check if the new WMM
element is different from the previous one and if so change the
parameter_set_count to imply stations to look into it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
When a new station is added, let it have some supported rates
(they're empty without this change), using the basic rates
that it must support to connect.
This, together with the kernel-side changes for client-side,
lets us finish the complete auth/assoc handshake with higher
rates than the mandatory ones, without any further config.
However, the downside to this is that a broken station that
doesn't check the basic rates are supported before it tries
to connect will possibly not get any response to its auth
frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a config option to allow setting a custom Basic NSS/MCS set. As a
default we use single stream HE-MCS 0-7.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Process HE information in (Re)Association Request frames and add HE
elements into (Re)Association Response frames when HE is enabled in the
BSS.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The HE Capibilities element has dynamic size due to the variable length
and optional fields at the end. Mask out the channel width capabilities
that are less than the configured. Only add the MCS/NSS sets for the
announced channel widths and also add the PPET elements.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This is used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These are used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These are used for both VHT and HE, so remove the misleading prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Bandwidth is used for both VHT and HE here.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
oper_chwidth is used for both VHT and HE here.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The bandwidth values are shared between VHT and HE mode so remove the
VHT specific prefix.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These bits might be set by the capabilities read from the kernel, so
mask them out if beamforming is not enabled in the local configuration.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This copying attempt was added incorrectly since that element is never
actually present in (Re)Association Request frames. It is only valid to
copy that element from the mesh peering frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
gcc 8.3.0 was apparently clever enough to optimize away the previously
used os_memset() to explicitly clear a stack buffer that contains keys
when that clearing happened just before returning from the function.
Since memset_s() is not exactly portable (or commonly available yet..),
use a less robust mechanism that is still pretty likely to prevent
current compilers from optimizing the explicit clearing of the memory
away.
Signed-off-by: Jouni Malinen <j@w1.fi>
The IE header length check was off-by-one and that could allow the loop
to read one octet beyond the end of the buffer before breaking out in
the second check.
Credit to OSS-Fuzz: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=14927
Fixes: 0a66ce3c49 ("WNM: Add support for SSID List element matching")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This AP behavior was missing from IEEE Std 802.11ai-2016, but it is
needed for the RSNE validation to work correctly and for a FILS STA to
be able to perform the mandatory check for RSNE matching when processing
the (Re)Association Response frame (as described in 802.11ai). REVmd
will be updating the standard to cover this AP case, so prepare the
implementation to match that. Without this, a FILS STA might reject
association whenever using FILS authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If none of the sr_control bits are set, we do not neet to add the IE to
the Beacon frame.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
While this should not happen in practical use cases,
wpa_get_ntp_timestamp() could return the same value when called twice in
a row quickly. Work around that case by enforcing a new Replay Counter
value based on stored last value.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds support to hostapd for configuring airtime policy settings for
stations as they connect to the access point. This is the userspace
component of the airtime policy enforcement system PoliFi described in
this paper: https://arxiv.org/abs/1902.03439
The Linux kernel part has been merged into mac80211 for the 5.1 dev
cycle.
The configuration mechanism has three modes: Static, dynamic and limit.
In static mode, weights can be set in the configuration file for
individual MAC addresses, which will be applied when the configured
stations connect.
In dynamic mode, weights are instead set per BSS, which will be scaled
by the number of active stations on that BSS, achieving the desired
aggregate weighing between the configured BSSes. Limit mode works like
dynamic mode, except that any BSS *not* marked as 'limited' is allowed
to exceed its configured share if a per-station fairness share would
assign more airtime to that BSS. See the paper for details on these
modes.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This provides a mechanism for configuring per-STA airtime weight for
airtime policy configuration.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This allows authenticator side to complete FT initial mobility domain
association using FT-EAP with PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When completing FT initial mobility domain association with EAP, store
XXKey/MPMK in the PMKSA cache instead of MSK. The previously stored MSK
was of no use since it could not be used as the XXKey for another FT
initial mobility domain association using PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is apparently possible to somehow trigger the driver to report a
channel switch event during ACS operation when the interface information
is not yet complete. hapd->iface->current_mode could be NULL in that
case and that would result in process termination due to NULL pointer
dereference.
It should not really be possible to trigger a channel switch during ACS
is running (i.e., before the AP mode operation has been started), but
since that has been seen in an arbitrary test sequence with interface
start/stop operations with various parameters (both valid and invalid),
better prevent a crash here by ignoring the unexpected event instead of
trying to process it.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Unexpected CHAN_SWITCH command could get this function using a NULL
pointer if the channel switch was requested while the interface was
already disabled.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
driver->hapd_deinit() is going to free the memory that the cached
pointers are pointing to, so clear the pointers to avoid possibility of
dereferencing used memory. It seemed to be possible to hit a code path
using those fields by issuing a CHAN_SWITCH command on disabled hostapd
interface in some cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds a ieee80211ax=0/1 line to the STATUS output to indicate
the configuration of ieee80211ax, which similar to ieee80211n and
ieee80211ac.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The first four octets of the element were used as a host byte order u32.
That is not correct on bigendian CPUs, so handle byte swapping needs
properly. Mark the he_oper_params field as le32 to explicitly indicate
the byte order and swap the generated params content based on CPU byte
order.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current code will always use the size required when all optional
elements are present. This will cause the Linux kernel to consider the
field to be malformed if the elements are not actually flagged as being
present.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
SPR allows us to detect OBSS overlaps and allows us to do adaptive CCA
thresholds. For this to work the AP needs to broadcast the element
first.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Properly populate the the HE Capabilities element with the info read
from the kernel.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
According to P802.11ax/D4.0 9.4.2.238 (HE Operation element) the BSS
Color Information field is located after the HE Operation Parameters
field. Fix the ordering of the bit masks/offsets for fields in these 3+1
octets used as a single 32-bit value. With these changes, Wireshark 3.2
is able to properly parse and display Beacon frames.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
IEEE P802.11ax/D4.0 9.4.2.243 "HE Operation element" indicates that the
special value 1023 in the TXOP Duration RTS Threshold field is used to
indicate that TXOP duration-based RTS is disabled. Use that value as the
default instead of the previously used value 0 which would really mean
threshold of 0 usec. Furthermore, the previous implementation did not
allow values larger than 255 to be used for this field while the field
is actually 10 bits in size.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This makes it easier to upper layer components to manage operating
channels in cases where the same radio is shared for both station and AP
mode virtual interfaces.
Signed-off-by: Omer Dagan <omer.dagan@tandemg.com>
Logs involving IEEE 802.11 Status Codes output the Status Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each status code using the latter part
of the Status Code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
The new hostapd configuration parameter dpp_controller can now be used
with the following subparameter values: ipaddr=<IP address>
pkhash=<hexdump>. This adds a new Controller into the configuration
(i.e., more than one can be configured) and all incoming DPP exchanges
that match the specified Controller public key hash are relayed to the
particular Controller.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to derive a PMK-R0 and PMK-R1 again for the case where an
association was started with FT protocol and PTK is rekeyed using 4-way
handshake. Instead, use the previously derived PMK-R1 to allow a new PTK
to be derived.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not try to derive a PMKID for EAPOL-key msg 1/4 when going through
4-way handshake to rekey PTK during an association that was started
through FT protocol.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to allow PTK rekeying to be performed through 4-way
handshake in an association started through FT protocol.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to avoid leaving some timers (e.g., for PTK rekeying)
running afrer a STA has disassociated.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
FT rules for PTK derivation do not use PMK. Remove the unused argument
to the PTK derivation function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The PMK and PMKID information from FILS ERP and FILS PMKSA caching needs
to be stored within struct wpa_state_machine for PTK to work. Without
this, PTK derivation would fail and attempt to go through rekeying would
result in disconnection. Furthermore, wpa_rekey_ptk() timer needs to be
started at the completion of FILS association since the place where it
was done for non-FILS cases at the end of 4-way handshake is not reached
when FILS authentication is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is possible for the SAE state machine to remove the STA and free the
sta pointer in the mesh use cases. handle_auth_sae() could have
dereferenced that pointer and used freed memory in some cases. Fix that
by explicitly checking whether the STA was removed.
Fixes: bb598c3bdd ("AP: Add support for full station state")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
ap_free_sta() frees the sta entry, so sta->addr cannot be used after
that call. Fix the sequence of these two calls to avoid use of freed
memory to determine which PMKSA cache entry to remove.
Fixes: 9f2cf23e2e ("mesh: Add support for PMKSA caching")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The external authentication command and event does not need to copy the
BSSID/SSID values into struct external_auth since those values are used
before returning from the call. Simplify this by using const u8 * to
external data instead of the array with a copy of the external data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend commit 5ff39c1380 ("SAE: Support external authentication
offload for driver-SME cases") to support external authentication
with drivers that implement AP SME by notifying the status of
SAE authentication to the driver after SAE handshake as the
driver acts as a pass through for the SAE Authentication frames.
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
beacon_set_done did not get reset to zero on disabling interface using
DISABLE control interface command and the subsequent ENABLE command will
caused configuration of Beacon/Probe Response/Association Response frame
IEs twice. The unnecessary two step configuration can be avoided by
resetting beacon_set_done on DISABLE so that ENABLE can bring up the
interface in a single step with fully updated IEs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
identity_buf may be NULL here. Handle this case explicitly by printing
"N/A" instead relying on snprintf converting this to "(null)" or some
other value based on unexpected NULL pointer.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Avoid duplicated code in each user of dpp_build_conf_req() by moving the
common encapsulation case into this helper function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When connected using FT-SAE key mgmt, use PMK from PMKSA cache as XXKey
for PMK-R0 and PMK-R1 derivations. This fixes an issue where FT key
hierarchy could not be established due to missing (not yet configured)
XXKey when using SAE PMKSA caching for the initial mobility domain
association.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Ethernet frames have minimum length of 64 octets and shorter frames may
end up getting arbitrary padding in the end. This would result in the
FT/RRB receiver rejecting the frame as an incorrectly protected one.
Work around this by padding the message so that it is never shorter than
the minimum Ethernet frame.
Unfortunately, this padding is apparently not enough with all Ethernet
devices and it is still possible to see extra two octet padding at the
end of the message even if larger frames are used (e.g., showed up with
128 byte frames). For now, work around this by trying to do AES-SIV
decryption with two octets shorter frame (ignore last two octets) if the
first attempt fails.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Merge the practically copy-pasted implementations in wpa_supplicant and
hostapd into a single shared implementation in dpp.c for managing
configurator and boostrapping information. This avoid unnecessary code
duplication and provides a convenient location for adding new global DPP
data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The memcpy calls added for exposing the PMK from wpa_auth module could
end up trying to copy the same memory buffer on top of itself.
Overlapping memory areas are not allowed with memcpy, so this could
result in undefined behavior. Fix this by making the copies conditional
on the updated value actually coming from somewhere else.
Fixes: b08c9ad0c7 ("AP: Expose PMK outside of wpa_auth module")
Signed-off-by: Jouni Malinen <j@w1.fi>
This code was after the FILS handling that would have encrypted the
frame. While FILS and OWE are never used together, the OWE handling
should really be before the FILS handling since no IEs can be added
after the FILS encryption step. In addition, the Diffie-Hellman
Parameter element is not a Vendor Specific element, so it should be
before some of the Vendor Specific elements even though it is not
defined in IEEE 802.11.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use Diffie-Hellman key exchange to derivate additional material for
PMK-to-PTK derivation to get PFS. The Diffie-Hellman Parameter element
(defined in OWE RFC 8110) is used in association frames to exchange the
DH public keys. For backwards compatibility, ignore missing
request/response DH parameter and fall back to no PFS in such cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
DPP allows Diffie-Hellman exchange to be used for PFS in PTK derivation.
This requires an additional Z.x (x coordinate of the DH shared secret)
to be passed to wpa_pmk_to_ptk(). This commit adds that to the function
and updates all the callers to pass NULL,0 for that part in preparation
of the DPP specific changes to start using this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous OWE implementation on the AP side rejected any
(Re)Association Request frame with the Diffie-Hellman Parameter element
if AKM was not OWE. This breaks compatibility with DPP PFS, so relax
that rule to allow DPP AKM to be used as well. While this commit alone
does not add support for PFS, this allows interoperability between
non-PFS implementation on the AP and a newer PFS implementation on the
STA.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Share a single parsing implementation for both hostapd and
wpa_supplicant to avoid code duplication. In addition, clean up the
implementation to be more easily extensible.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The queue_len * 50 ms wait time was too large with the retransmission
timeouts used in the mesh case for SAE. The maximum wait of 750 ms was
enough to prevent successful completion of authentication after having
hit the maximum queue length. While the previous commit is enough to
allow this to complete successfully in couple of retries, it looks like
a smaller wait time should be used here even if it means potentially
using more CPU.
Drop the processing wait time to queue_len * 10 ms so that the maximum
wait time is 150 ms if the queue is full.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previous design of simply queuing all SAE commit messages was not
exactly good at allowing recovery from a flooding state if the valid
peer used frequent retransmissions of the SAE message. This could
happen, e.g., with mesh BSSs using SAE. The frequent retransmissions and
restarts of SAE authentication combined with SAE confirm messages
bypassing the queue ended up in not being able to finish SAE exchange
successfully.
Fix this by modifying the queuing policy to queue SAE confirm messages
if there is a queued SAE commit message from the same peer so that the
messages within the same exchange do not get reordered. In addition,
replace queued SAE commit/confirm message if a new matching message is
received from the same peer STA. This is useful for the case where the
peer restarts SAE more quickly than the local end has time to process
the queued messages.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use this new message from Enrollee to Configurator to indicate result of
the config object provisioning if both devices support protocol version
2 or newer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Derive PMKR1Name during the FILS authentication step, verify that the
station uses matching PMKR1Name in (Re)Association Request frame, and
add RSNE[PMKR1Name] into (Re)Association Response frame when going
through FT initial mobility domain association using FILS. These steps
were missed from the initial implementation, but are needed to match the
IEEE 802.11ai requirements for explicit confirmation of the FT key
hierarchy (similarly to what is done in FT 4-way handshake when FILS is
not used).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This gets rid of a confusing error message "FILS: Failed to add PMKSA
cache entry based on ERP" for cases where PMKSA caching is disabled in
hostapd (disable_pmksa_caching=1). Functionality remains unchanged,
i.e., no cache entry was added before this change either.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
hostapd configuration parameters fragm_threshold and rts_threshold were
documented to disable the threshold with value -1 and not change driver
configuration if the parameter is not included. However, -1 was mapped
into not changing the driver value, so the explicit disabling part did
not work.
Replace the default values for these to be -2 so that explicitly set
configuration value -1 can be distinguished from the case of not
including the parameter. Map the -1 value to a driver request to disable
the threshold. Ignore any error from this operation just in case to
avoid breaking functionality should some drivers not accept the (u32) -1
value as a threshold value request to disable the mechanism.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This patch added 'check_cert_subject' support to match the value of
every field against the DN of the subject in the client certificate. If
the values do not match, the certificate verification will fail and will
reject the user.
This option allows hostapd to match every individual field in the right
order, also allow '*' character as a wildcard (e.g OU=Development*).
Note: hostapd will match string up to 'wildcard' against the DN of the
subject in the client certificate for every individual field.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
Signed-off-by: Jouni Malinen <j@w1.fi>
Include only one of hostapd_mgmt_rx() and hostapd_action_rx() functions
in the build. Previously, NEED_AP_MLME builds (i.e., cases where hostapd
AP MLME implementation is included) included both of these functions and
both were tried in sequence. In addition to being difficult to
understand, that could result in unexpected behavior if
hostapd_mgmt_rx() rejected a frame and return 0 to allow
hostapd_action_rx() to attempt to process the frame.
All the operations included in hostapd_action_rx() are supposed to be
available through the hostapd_mgmt_rx() call in handle_action() and
those should result in the exact same Category/Action-based handler
function to be called in the end. As such, this should not result in
different behavior. And if there is a difference, that would be pointing
at a hidden bug that would need to be fixed anyway. Furthermore, builds
without NEED_AP_MLME would not have any difference in behavior or
contents of the binary either.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no need to go through the following handler calls in
hostapd_action_rx() after having found the matching WLAN_ACTION_WNM
handler.
Signed-off-by: Jouni Malinen <j@w1.fi>
hostapd_action_rx() was pointing at incorrect field (Action vs.
Category) for the wpa_ft_action_rx() call and the length check for SA
Query Action frames. This resulted in those frames getting dropped as
invalid (FT) or ignored as truncated (SA Query). Fix this by pointing to
the correct place at the beginning of the frame body.
This issue had a long history. These were broken during cleanup in
commit dbfb8e82ff ("Remove unnecessary EVENT_RX_ACTION") which
actually fixed the initial reason for the error accidentally. It was
just that that error was needed to cancel out another earlier error..
One of the errors came from misuse of the EVENT_RX_ACTION API in commit
deca6eff74 ("atheros: Add new IEEE 802.11r driver_ops"). That pointed
struct rx_action data/len to cover the Action frame from the Category
field to the end of the frame body while the API was documented to cover
Action field to the end of the frame body. This error was cancelled by
another error in commit 88b32a99d3 ("FT: Add FT AP support for drivers
that manage MLME internally") that called wpa_ft_action_rx() with the
struct rx_action::data field as the second argument. That argument needs
to point to the Category field, but that struct rx_action field was
supposed to point to the Action field.
Number of the Action frame handlers added into hostapd_action_rx() had
been fixed more or less accidentally after this in various other
commits, but the FT and SA Query handlers had ended up maintaining the
incorrect operations. This is now fixing those.
This seems to fix at least some cases of FT-over-DS with drivers that
use driver-based AP MLME. Such drivers might use internal SA Query
processing, so it is not clear whether that part actually fixes any real
issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Copy the Finite Cyclic Group field value from the request to the
response Authentication frame if we end up rejecting the request due to
unsupported group.
IEEE Std 802.11-2016 has conflicting statements about this behavior.
Table 9-36 (Presence of fields and elements in Authentication frames)
indicates that the Finite Cyclic Group field is only included with
status code values 0 (success) and 76 (anti-clogging token request)
while SAE protocol description implying that the Finite Cyclic Group
field is set to the rejected group (12.4.8.6.3 and 12.4.8.6.4).
The standard language needs to cleaned up to describe this
unambiguously, but since it looks safe to add the field into the
rejection case and since there is desire to have the field present to be
able to implement what exactly is stated in 12.4.8.6.4, it looks
reasonable to move ahead with the AP mode implementation change. There
is no change in wpa_supplicant for now to modify its behavior based on
whether this field is present, i.e., wpa_supplicant will continue to
work with both the old and new hostapd behavior for SAE group
negotiation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new hostapd configuration parameter wps_cred_add_sae=1 can be used
to request hostapd to add SAE configuration whenever WPS is used to
configure the AP to use WPA2-PSK and the credential includes a
passphrase (instead of PSK). This can be used to enable WPA3-Personal
transition mode with both SAE and PSK enabled and PMF enabled for PSK
and required for SAE associations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not start SAE authentication from scratch if a STA starts a new
attempt for the same group while we still have previously generated PWE
available. Instead, use the previously generated PWE as-is and skip
anti-clogging token exchange since the heavy processing is already
completed. This saves unnecessary processing on the AP side in case the
STA failed to complete authentication on the first attempt (e.g., due to
heavy SAE load on the AP causing a timeout) and makes it more likely for
a valid STA to be able to complete SAE authentication during a DoS
attack.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a 16-bit token index into the anti-clogging token. This can be used
to enforce only a single use of each issued anti-clogging token request.
The token value is now token-index |
last-30-octets-of(HMAC-SHA256(sae_token_key, STA-MAC-address |
token-index)), i.e., the first two octets of the SHA256 hash value are
replaced with the token-index and token-index itself is protected as
part of the HMAC context data.
Track the used 16-bit token index values and accept received tokens only
if they use an index value that has been requested, but has not yet been
used. This makes it a bit more difficult for an attacker to perform DoS
attacks against the heavy CPU operations needed for processing SAE
commit since the attacker cannot simply replay the same frame multiple
times and instead, needs to request each token separately.
While this does not add significant extra processing/CPU need for the
attacker, this can be helpful in combination with the queued processing
of SAE commit messages in enforcing more delay during flooding of SAE
commit messages since the new anti-clogging token values are not
returned before the new message goes through the processing queue.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows better control of processing new SAE sessions so that other
operations can be given higher priority during bursts of SAE requests,
e.g., during a potential DoS attack. The receive commit messages are
queued (up to maximum of 15 entries) and processed from eloop callback.
If the queue has multiple pending entries, more wait time is used to go
through the each new entry to reduce heavy CPU load from SAE processing.
Enable anti-clogging token use also based on the pending commit message
queue and not only based on the already started sessions.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Change the AP mode default for SAE to enable only the group 19 instead
of enabling all ECC groups that are supported by the used crypto library
and the SAE implementations. The main reason for this is to avoid
enabling groups that are not as strong as the mandatory-to-support group
19 (i.e., groups 25 and 26). In addition, this disables heavier groups
by default.
In addition, add a warning about MODP groups 1, 2, 5, 22, 23, and 24
based on "MUST NOT" or "SHOULD NOT" categorization in RFC 8247. All the
MODP groups were already disabled by default and would have needed
explicit configuration to be allowed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extension of VLAN assignment code had a bug in one of the code
paths where vlan_id could have been left uninitialized. This could
result in SAE authentication getting rejected in cases where VLAN
assignment is not used if the uninitialized stack memory had nonzero
value.
Fixes: dbfa691df4 ("VLAN assignment based on used WPA/WPA2 passphrase/PSK")
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid an unnecessary unsigned integer overflow warning due to loop index
j-- use.
hostapd.c:661:10: runtime error: unsigned integer overflow: 0 - 1 cannot be represented in type 'unsigned int'
Signed-off-by: Jouni Malinen <j@w1.fi>
(&mgmt->u.deauth.reason_code + 1) is not exactly clean and now that we
have the u8 variable[] member in the struct after this field, use that
directly to avoid clang compiler warning:
ctrl_iface_ap.c:454:18: error: taking address of packed member
'reason_code' of class or structure 'ieee80211_mgmt::(anonymous
union)::(anonymous)' may result in an unaligned pointer value
[-Werror,-Waddress-of-packed-member]
Signed-off-by: Jouni Malinen <j@w1.fi>
Split the check and decrementation into separate steps to avoid an
unnecessary UBSan warning.
hostapd.c:1895:14: runtime error: unsigned integer overflow: 0 - 1 cannot be represented in type 'size_t' (aka 'unsigned long')
Signed-off-by: Jouni Malinen <j@w1.fi>
hapd->conf might be NULL in case initialized failed, so better be
prepared for that when debug printing interface name in the deinit path.
hostapd.c:312:54: runtime error: member access within null pointer of type 'struct hostapd_bss_config'
hostapd.c:351:29: runtime error: member access within null pointer of type 'struct hostapd_bss_config'
hostapd.c:2158:18: runtime error: member access within null pointer of type 'struct hostapd_bss_config'
Signed-off-by: Jouni Malinen <j@w1.fi>
iface->num_bss is unsigned integer, so need to explicit typecast it to
unsigned before decrementation by one even when the result is stored in
an unsigned integer.
../src/ap/hostapd.c:2185:26: runtime error: unsigned integer overflow: 0 - 1 cannot be represented in type 'unsigned long'
Signed-off-by: Jouni Malinen <j@w1.fi>
According to IEEE Std 802.11-2016, 9.4.2.25 when fields of an RSNE are
not included, the default values are used. The cipher suite defaults
were hardcoded to CCMP in the previous implementation, but the default
is actually different for DMG: GCMP (per 9.4.2.25.2).
It is not possible to find out from the RSNE if the network is non-DMG
or DMG, so callers of wpa_parse_wpa_ie_rsn() need to handle this case
based on context, which can be different for each caller.
In order to fix this issue, add flags to the wpa_ie_data indicating
whether pairwise/group ciphers were included in the RSNE. Callers can
check these flags and fill in the appropriate ciphers. The
wpa_parse_wpa_ie_rsn() function still initializes the ciphers to CCMP by
default so existing callers will not break. This change also fixes some
callers which need to handle the DMG network case.
Signed-off-by: Lior David <liord@codeaurora.org>
The Wi-Fi Alliance Multi-AP Specification v1.0 allows onboarding of a
backhaul STA through WPS. To enable this, the WPS Registrar offers a
different set of credentials (backhaul credentials instead of fronthaul
credentials) when the Multi-AP subelement is present in the WFA vendor
extension element of the WSC M1 message.
Add new configuration options to specify the backhaul credentials for
the hostapd internal registrar: multi_ap_backhaul_ssid,
multi_ap_backhaul_wpa_psk, multi_ap_backhaul_wpa_passphrase. These are
only relevant for a fronthaul SSID, i.e., where multi_ap is set to 2 or
3. When these options are set, pass the backhaul credentials instead of
the normal credentials when the Multi-AP subelement is present.
Ignore the Multi-AP subelement if the backhaul config options are not
set. Note that for an SSID which is fronthaul and backhaul at the same
time (i.e., multi_ap == 3), this results in the correct credentials
being sent anyway.
The security to be used for the backaul BSS is fixed to WPA2PSK. The
Multi-AP Specification only allows Open and WPA2PSK networks to be
configured. Although not stated explicitly, the backhaul link is
intended to be always encrypted, hence WPA2PSK.
To build the credentials, the credential-building code is essentially
copied and simplified. Indeed, the backhaul credentials are always
WPA2PSK and never use per-device PSK. All the options set for the
fronthaul BSS WPS are simply ignored.
Signed-off-by: Davina Lu <ylu@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Cc: Marianna Carrera <marianna.carrera.so@quantenna.com>
The Multi-AP specification only specifies that information elements have
to be added to the Association Request and Association Response frame;
it doesn't specify anything about what should be done in case they are
missing. Previously, we rejected non-backhaul associations on a
backhaul-only BSS, and non-fronthaul associations on a fronthaul-only
BSS.
However, this makes WPS fail when fronthaul and backhaul are separate
SSIDs. Indeed, WPS for the backhaul link is performed on the *fronthaul*
SSID. Thus, the Association Request frmae used for WPS *will* contain
the Multi-AP IE indicating a backhaul STA. Rejecting that association
makes WPS fail.
Therefore, accept a multi-AP backhaul STA Association Request frame on a
fronthaul-only BSS. Still issue a warning about it, but only at level
DEBUG intead of INFO. Also change the condition checking to make it
clearer.
While we're at it, also fix the handling of unexpected bits in the
Multi-AP IE. 4 bits are reserved in the specification, so these
certainly have to be ignored. The specification also doesn't say that
setting one of the other bits is not allowed. Therefore, only report
unexpected values in the Multi-AP IE, don't reject because of it. Note
that a malformed IE (containing more than one byte) still triggers a
rejection.
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
str_token() can return NULL for the name if the remaining token contains
only the delimiter. Fix this to avoid NULL pointer dereference with a
corner case of an invalid value used in the configuration.
Fixes: ec5c39a557 ("AP: Allow identifying which passphrase station used with wpa_psk_file")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The new sae_password parameter [|vlanid=<VLAN ID>] can now be used to
assign stations to a specific VLAN based on which SAE Password
Identifier they use. This is similar to the WPA2-Enterprise case where
the RADIUS server can assign stations to different VLANs and the
WPA2-Personal case where vlanid parameter in wpa_psk_file is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Extend wpa_psk_file to allow an optional VLAN ID to be specified with
"vlanid=<VLAN ID>" prefix on the line. If VLAN ID is specified and the
particular wpa_psk_file entry is used for a station, that station is
bound to the specified VLAN. This can be used to operate a single
WPA2-Personal BSS with multiple VLANs based on the used passphrase/PSK.
This is similar to the WPA2-Enterprise case where the RADIUS server can
assign stations to different VLANs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the ap_handle_timer() timeout is reached for a not-associated STA, do
not default to disassociating that STA first since Disassociation frame
is not really appropriate to send to a STA that is not in associated
state. Instead, skip directly to deauthentication and STA entry removal.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add test-eapol program that can be used for fuzzing the EAPOL-Key
Supplicant and Authenticator implementations. This tool can write
Supplicant or Authenticator messages into a file as an initialization
step and for the fuzzing step, that file (with potential modifications)
can be used to replace the internally generated message contents.
The TEST_FUZZ=y build parameter is used to make a special build where a
hardcoded random number generator and hardcoded timestamp are used to
force deterministic behavior for the EAPOL-Key operations. This will
also make the implementation ignore Key MIC and AES keywrap errors to
allow processing of modified messages to continue further.
Signed-off-by: Jouni Malinen <j@w1.fi>
ieee802_11_rx_wnmsleep_req() might have been called for a short frame
that has no more payload after the Public Action field, i.e., with len
== 0. The bounds checking for the payload length was done only for the
information elements while the one octet Dialog Token field was read
unconditionally. In the original implementation, this could have
resulted in reading one octet beyond the end of the received frame data.
This case has not been reachable after the commit e0785ebbbd ("Use
more consistent Action frame RX handling in both AP mode paths"), but it
is better to address the specific issue in ieee802_11_rx_wnmsleep_req()
as well for additional protection against accidential removal of the
check and also to have something that can be merged into an older
version (pre-v2.7) if desired. The comments below apply for such older
versions where the case could have been reachable.
Depending on driver interface specific mechanism used for fetching the
frame, this could result in reading one octet beyond the end of a
stack/hash buffer or reading an uninitialized octet from within a
buffer. The actual value that was read as the Dialog Token field is not
used since the function returns immediately after having read this value
when there is no information elements following the field.
This issue was initially added in commit d32d94dbf4 ("WNM: Add
WNM-Sleep Mode implementation for AP") (with CONFIG_IEEE80211V=y build
option) and it remained in place during number of cleanup and fix
changes in this area and renaming of the build parameter to
CONFIG_WNM=y. The impacted function was not included in any default
build without one of the these optional build options being explicitly
enabled. CONFIG_WNM=y is still documented as "experimental and not
complete implementation" in hostapd/defconfig. In addition, commit
114f2830d2 ("WNM: Ignore WNM-Sleep Mode Request in wnm_sleep_mode=0
case") made this function exit before the impact read if WNM-Sleep Mode
support was not explicitly enabled in runtime configuration
(wnm_sleep_mode=1 in hostapd.conf). Commit e0785ebbbd ("Use more
consistent Action frame RX handling in both AP mode paths") made this
code unreachable in practice.
Add an explicit check that the frame has enough payload before reading
the Dialog Token field in ieee802_11_rx_wnmsleep_req().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This patch adds a new flag 'crl_reload_interval' to reload CRL
periodically. This can be used to reload ca_cert file and the included
CRL information on every new TLS session if difference between the last
reload and the current time in seconds is greater than
crl_reload_interval.
This reloading is used for cases where check_crl is 1 or 2 and the CRL
is included in the ca_file.
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
It is now possible to optionally specify keyid for
each wpa_psk_file entry:
keyid=something 00:00:00:00:00:00 secretpassphrase
When station connects and the passphrase it used
has an associated keyid it will be appended to the
AP-STA-CONNECTED event string:
wlan0: AP-STA-CONNECTED 00:36:76:21:dc:7b keyid=something
It's also possible to retrieve it through the control interface:
$ hostapd_cli all_sta
Selected interface 'ap0'
00:36:76:21:dc:7b
...
keyid=something
New hostapd is able to read old wpa_psk_file. However, old hostapd will
not be able to read the new wpa_psk_file if it includes keyids.
Signed-off-by: Michal Kazior <michal@plume.com>
This doesn't change any behavior on its own. It's going to be used to
expose per-station keyids and allow reloading passphrases in runtime.
Signed-off-by: Michal Kazior <michal@plume.com>
Support the new Extended Capabilities field bits 81 and 82 to indicate
whether SAe Password Identifiers are in use.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for configuring parameters for the MU EDCA Parameter Set
element per IEEE P802.11ax/D3.0.
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
When an interface is re-enabled after it was disabled during CAC, it
won't ever get active since hostapd is waiting for a CAC_FINISHED while
kernel side is waiting for a CMD_RADAR_DETECT to start a CAC.
This commit checks for a pending CAC when an interface is enabled and if
so restarts its DFS processing.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
While the AP is configured to enable both FT-PSK and WPA-PSK, an HP
printer request both AKMs (copied from AP?) in Association Request
frame, but don't add MDIE and don't use FT. This results in the
connection failing.
Next in logs we see:
RSN: Trying to use FT, but MDIE not included
IE - hexdump(len=26): 30 18 01 00 00 0f ac 04 01 00 00 0f ac 04
02 00 00 0f ac 02 00 0f ac 04 00 00
This is seen with some HP and Epson printers. Work around this by
stripping FT AKM(s) when MDE is not present and there is still a non-FT
AKM available.
Signed-off-by: Janusz Dziedzic <janusz@plumewifi.com>
While selecting a new channel as a reaction to radar event we need to
take into account supported bandwidth for each channel provided via
nl80211. Without this modification hostapd might select an unsupported
channel that would fail during AP startup.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
While doing automatic channel selection we need to take into account
supported bandwidth for each channel provided via nl80211. Without this
modification hostapd might select an unsupported channel which would
fail during AP startup.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
This adds checks to common code to verify supported bandwidth options
for each channel using nl80211-provided info. No support of additional
modes is added, just additional checks. Such checks are needed because
driver/hardware can declare more strict limitations than declared in the
IEEE 802.11 standard. Without this patch hostapd might select
unsupported channel and that will fail because Linux kernel does check
channel bandwidth limitations.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Add support for 160 MHz BW channels to automatic channel selection
algorithm. Only 36 and 100 channels are supported as 160 MHz channels.
Signed-off-by: Dmitry Lebed <lebed.dmitry@gmail.com>
FT-over-the-DS has a special case where the STA entry (and as such, the
TK) has not yet been configured to the driver depending on which driver
interface is used. For that case, allow add-STA operation to be used
(instead of set-STA). This is needed to allow mac80211-based drivers to
accept the STA parameter configuration. Since this is after a new
FT-over-DS exchange, a new TK has been derived after the last STA entry
was added to the driver, so key reinstallation is not a concern for this
case.
Fixes: 0e3bd7ac68 ("hostapd: Avoid key reinstallation in FT handshake")
Signed-off-by: Jouni Malinen <j@w1.fi>
The documentation in the hostapd.conf file says that the dynamic_vlan
variable is used to control whether VLAN assignments are accepted from a
RADIUS server. The implication seems to be that a static VLAN assignment
will come from the accept_mac_file if dynamic_vlan is set to 0, and a
dynamic assignment will come from the RADIUS server if dynamic_vlan is
set to 1. Instead, I'm seeing that the static settings from the
accept_mac_file are ignored if dynamic_vlan is set to 0, but used if
dynamic_vlan is set to 1. If dynamic_vlan is set to 1 and the RADIUS
server does not provide a VLAN, then the accept_mac_file assignment is
overridden and the STA is assigned to the default non-VLANed interface.
If my understanding of the expected behavior is correct, then I believe
the problem is in ap_sta_set_vlan(). That routine checks the
dynamic_vlan setting, but has no way of determining whether the incoming
vlan_desc is static (i.e., from accept_mac_file) or dynamic (i.e., from
a RADIUS server).
I've attached a patch that gets hostapd working as I believe it's meant
to, and updates the documentation to make the implicit behavior
explicit.
The functional changes are:
- hostapd_allowed_address() will always extract the vlan_id from the
accept_macs file. It will not update the vlan_id from the RADIUS cache
if dynamic_vlan is DISABLED.
- hostapd_acl_recv_radius() will not update the cached vlan_id if
dynamic_vlan is DISABLED.
- ieee802_1x_receive_auth() will not update the vlan_id if dynamic_vlan
is DISABLED.
More cosmetic:
Most of the delta is just moving code out of ieee802_1x_receive_auth()
into a new ieee802_1x_update_vlan() routine. While I initially did this
because the new DISABLED check introduced excessive indentation, it has
the added advantage of eliminating the vlan_description allocation and
os_memset() call for all DYNAMIC_VLAN_DISABLED configs.
I've done a couple rounds of review offline with Michael Braun (who has
done much of the work in this part of the code) and incorporated his
feedback.
If dynamic_vlan=0 (disabled), vlan assignments will be managed using the
local accept_mac_file ACL file, even if a RADIUS server is being used
for user authentication. This allows us to manage users and devices
independently.
Signed-off-by: Nils Nieuwejaar <nils.nieuwejaar@gmail.com>
After performing a successful channel switch, the AP should update its
own neighbor report element, so do this from src/ap/drv_callbacks.c
after a successful switch.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Move functions corresponding to neighbor report elements to
src/ap/neighbor_db.[c,h] in preparation to using them after channel
switch from src/ap/drv_callbacks.c.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Legacy ioctl() through SIOCDEVPRIVATE are deprecated. Follow the
approach taken by bridge-utils and make use of new bridge ioctl's
whenever possible.
For example, using legacy ioctl() breaks dynamic VLAN mode on 32-bit
Linux systems running 64-bit kernels.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
If the internal EAP server is used instead of an external RADIUS server,
sm->identity does not get set. Use the identity from the internal EAP
server in such case to get the dot1xAuthSessionUserName value in STA MIB
information.
Signed-off-by: Jouni Malinen <j@w1.fi>
Try to make RSSI-based rejection of associating stations a bit less
likely to trigger false rejections by considering RSSI from the last
received Authentication frame. Association is rejected only if both the
Authentication and (Re)Association Request frames are below the RSSI
threshold.
Signed-off-by: Jouni Malinen <j@w1.fi>
An AP might reject a STA association request due to low RSSI. In such
case, the AP informs the STA the desired RSSI improvement and a retry
timeout. The STA might retry to associate even if the RSSI hasn't
improved if the retry timeout expired.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Add the ability to ignore time-based CRL errors from OpenSSL by
specifying a new configuration parameter, check_crl_strict=0.
This causes the following:
- This setting does nothing when CRL checking is not enabled.
- When CRL is enabled, "strict mode" will cause CRL time errors to not
be ignored and will continue behaving as it currently does.
- When CRL is enabled, disabling strict mode will cause CRL time
errors to be ignored and will allow connections.
By default, check_crl_strict is set to 1, or strict mode, to keep
current functionality.
Signed-off-by: Sam Voss <sam.voss@rockwellcollins.com>
This makes it possible to use ECDSA certificates with EAP-TLS/TTLS/etc.
It should be noted that when using Suite B, different mechanism is used
to specify the allowed ECDH curves and this new parameter must not be
used in such cases.
Signed-off-by: Hristo Venev <hristo@venev.name>
handle_dhcp() was first trying to learn the IP address of an associated
STA before doing broadcast-to-unicast conversion. This could result in
not converting some DHCPACK messages since the address learning part
aborts processing by returning from the function in various cases.
Reorder these operations to allow broadcast-to-unicast conversion to
happen even if an associated STA entry is not updated based on a
DHCPACK.
Signed-off-by: Jouni Malinen <j@w1.fi>
These do not really get truncated in practice, but it looks like some
newer compilers warn about the prints, so silence those by checking the
result and do something a bit more useful if the output would actually
get truncated.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it easier to integrate dynamic VLANs in custom network
configurations. The bridge name is added after the interface name in the
vlan_file line, also separated by whitespace.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable FTM responder and configure LCI and civic if ftm_responder
configuration option is set. Since ftm_responder configuration existed
before and was used to set extended capability bits, don't fail AP setup
flow if ftm_responder is set, but the driver doesn't advertise FTM
responder support.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
The purpose of Multi-AP specification is to enable inter-operability
across Wi-Fi access points (APs) from different vendors.
This patch introduces one new configuration parameter 'multi_ap' to
enable Multi-AP functionality and to configure the BSS as a backhaul
and/or fronthaul BSS.
Advertise vendor specific Multi-AP capabilities in (Re)Association
Response frame, if Multi-AP functionality is enabled through the
configuration parameter.
A backhaul AP must support receiving both 3addr and 4addr frames from a
backhaul STA, so create a VLAN for it just like is done for WDS, i.e.,
by calling hostapd_set_wds_sta(). Since Multi-AP requires WPA2 (never
WEP), we can safely call hostapd_set_wds_encryption() as well and we can
reuse the entire WDS condition.
To parse the Multi-AP Extension subelement, we use get_ie(): even though
that function is meant for parsing IEs, it works for subelements.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Include and verify the OCI element in WNM-Sleep Exit Request and
Response frames. In case verification fails, the frame is silently
ignored.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
After the network changed to a new channel, perform an SA Query with the
AP after a random delay if OCV was negotiated for the association. This
is used to confirm that we are still operating on the real operating
channel of the network. This commit is adding only the station side
functionality for this, i.e., the AP behavior is not changed to
disconnect stations with OCV that do not go through SA Query.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Include an OCI element in SA Query Request and Response frames if OCV
has been negotiated.
On Linux, a kernel patch is needed to let clients correctly handle SA
Query Requests that contain an OCI element. Without this patch, the
kernel will reply to the SA Query Request itself, without verifying the
included OCI. Additionally, the SA Query Response sent by the kernel
will not include an OCI element. The correct operation of the AP does
not require a kernel patch.
Without the corresponding kernel patch, SA Query Requests sent by the
client are still valid, meaning they do include an OCI element.
Note that an AP does not require any kernel patches. In other words, SA
Query frames sent and received by the AP are properly handled, even
without a kernel patch.
As a result, the kernel patch is only required to make the client properly
process and respond to a SA Query Request from the AP. Without this
patch, the client will send a SA Query Response without an OCI element,
causing the AP to silently ignore the response and eventually disconnect
the client from the network if OCV has been negotiated to be used.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Include and verify the the OCI element in (Re)Association Request and
Response frames of the FT handshake. In case verification fails, the
handshake message is silently ignored.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Verify the received OCI element in the 4-way and group key handshakes.
If verification fails, the handshake message is silently dropped.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Use the information elements that were present in the (Re)Association
Request frame to derive the maximum bandwidth the AP will use to
transmit frames to a specific STA. By using this approach, we don't need
to query the kernel for this information, and avoid having to add a
driver API for that.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
If Operating Channel Verification is negotiated, include the OCI KDE
element in EAPOL-Key msg 2/4 and 3/4 of the 4-way handshake and both
messages of the group key handshake.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Set the OCV bit in RSN capabilities (RSNE) based on AP mode
configuration. Do the same for OSEN since it follows the RSNE field
definitions.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
APs and mesh peers use the VHT Operation element to advertise certain
channel properties (e.g., the bandwidth of the channel). Save this
information element so we can later access this information.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This adds the necessary functions and callbacks to make the channel_info
driver API available to the authenticator state machine that implements
the 4-way and group key handshake. This is needed for OCV.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
