Commit graph

423 commits

Author SHA1 Message Date
Masashi Honma
5b78493f3b mesh: Add mesh interface creation command for mesh gate
The mesh gate is used to bridge (or route) between mesh network and
another network. For example, mesh gate acts as router between mesh
network and IEEE 802.11 BSS network.

This command makes a virtual mesh interface to be used for mesh gate.

This command expects to be used like this.

wpa_cli -i wlan0 MESH_INTERFACE_ADD ifname=mesh0
wpa_cli -i mesh0 add_network
wpa_cli -i mesh0 set_network 0 ssid '"commell_2X_mmm"'
wpa_cli -i mesh0 set_network 0 mode 5
wpa_cli -i mesh0 set_network 0 frequency 2412
wpa_cli -i mesh0 set_network 0 key_mgmt SAE
wpa_cli -i mesh0 set_network 0 psk '"01234567"'
wpa_cli -i mesh0 mesh_group_add 0
wpa_cli -i wlan0 mesh_group_remove mesh0

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-14 23:27:43 +02:00
Jouni Malinen
f77cedc11a WPS ER: Remove unnecessary return value
wps_er_deinit() cannot fail and it does not return anything, so neither
should wpas_wps_er_stop().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-14 02:28:03 +02:00
Jouni Malinen
5407c69d15 Remove unnecessary STA_AUTOCONNECT handler function
This function could not fail and it can be replaced with a single
line variable update that takes less code than the function call.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:27:41 +02:00
Jouni Malinen
a1144000cd Remove unnecessary return value
wpa_bss_flush*() cannot fail and as such, there is no need for
wpa_supplicant_ctrl_iface_bss_flush() to return a value either.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:22:23 +02:00
Jouni Malinen
5ac73acf12 Simplify eapol_sm_get_mib() result handling
This function cannot return negative value, so no need to check for
that. If there is not enough room in the buffer or if something
unexpected happens, 0 is returned.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-13 19:15:38 +02:00
Jouni Malinen
43a66ecba3 Fix SCAN control interface command error cases
Update the scan parameters in wpa_s only in case the scan command is
going to be executed. In other words, do not change the parameters for
an ongoing scan (the SCAN command is rejected with FAIL-BUSY) or if any
of the parameters is invalid.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-12 01:12:15 +02:00
Jouni Malinen
b68d602dc4 Fix ANQP_GET/HS20_GET_ANQP parsing to skip space after address
The space following the BSSID was not skipped properly if the following
parameter started with the "hs20:" prefix. For other cases, atoi() ended
up ignoring the space, but it is cleaner to skip it anyway for all
cases.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-11 15:18:11 +02:00
Jouni Malinen
97cfe110dc Clear wpa_s->disconnected on ctrl_iface FLUSH
This is needed to get into more consistent state after the FLUSH
command. DISCONNECT followed by FLUSH could result in
wpa_s->disconnected being left to 1 and this resulted in a test failure,
e.g., when running wpas_ctrl_dup_network followed by
wpas_ctrl_enable_disable_network where the latter was expecting
ENABLE_NETWORK on a disabled network to connect automatically and that
does not happen if wpa_s->disconnected == 1.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-08 16:22:13 +02:00
Jouni Malinen
aaadd72733 Check os_snprintf() result more consistently - more checks
Add more os_snprintf() result validation checks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
1d39977136 Check os_snprintf() result more consistently
While these are using practically large enoungh buffer sizes, it is
better to be more consistent with checking os_snprintf() return value.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
1f102d3bb0 Check os_snprintf() result more consistently - manual
This converts os_snprintf() result validation cases to use
os_snprintf_error() for cases that were note covered by spatch and
semantic patches.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
7bdd8981f7 Check os_snprintf() result more consistently - automatic 2
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the comparison was 'res > size' instead of
'res >= size'. These changes were done automatically with spatch using
the following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || \( E1 > E3 \| (size_t) E1 > E3 \| E1 > (int) E3 \))
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
d85e1fc8a5 Check os_snprintf() result more consistently - automatic 1
This converts os_snprintf() result validation cases to use
os_snprintf_error() where the exact rule used in os_snprintf_error() was
used. These changes were done automatically with spatch using the
following semantic patch:

@@
identifier E1;
expression E2,E3,E4,E5,E6;
statement S1;
@@

(
  E1 = os_snprintf(E2, E3, ...);
|
  int E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = os_snprintf(E2, E3, ...);
|
  if (E5)
	E1 = os_snprintf(E2, E3, ...);
  else if (E6)
	E1 = os_snprintf(E2, E3, ...);
  else
	E1 = 0;
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else if (E6) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	return -1;
  }
|
  if (E5) {
	...
	E1 = os_snprintf(E2, E3, ...);
  } else {
	...
	E1 = os_snprintf(E2, E3, ...);
  }
)
? os_free(E4);
- if (E1 < 0 || \( E1 >= E3 \| (size_t) E1 >= E3 \| (unsigned int) E1 >= E3 \| E1 >= (int) E3 \))
+ if (os_snprintf_error(E3, E1))
(
  S1
|
{ ... }
)

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
a80ba67a26 Check os_snprintf() result more consistently - success case
This converts os_snprintf() result validation cases to use
os_snprintf_error() in cases where success condition was used to execute
a step. These changes were done automatically with spatch using the
following semantic patch:

@@
expression E1,E2,E3;
statement S1;
@@

  E1 = os_snprintf(E2, E3, ...);
- if (\( E1 >= 0 \| E1 > 0 \) && \( (size_t) E1 < E3 \| E1 < (int) E3 \| E1 < E3 \))
+ if (!os_snprintf_error(E3, E1))
  S1

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
c054190603 Fix DUP_NETWORK debug print on error case
Incorrect network id was printed in debug output if DUP_NETWORK
destination network was not found.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Jouni Malinen
49328f0756 Remove unnecessary ctrl_iface command check
MESH_GROUP_REMOVE always passes in the cmd pointer, so this cannot
really be NULL.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:06 +02:00
Jouni Malinen
d02dcb28bc Remove unnecessary ctrl_iface cmd check
This pointer cannot be NULL sicne it is called only from this file and
with a valid pointer to the received command.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:07:56 +02:00
Jouni Malinen
65d9a5e254 ERP: Add wpa_supplicant ERP_FLUSH ctrl_iface command
This can be used to flush all the ERP keys.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-04 12:16:29 +02:00
Jouni Malinen
02a8d45ace ERP: Add support for ERP on EAP peer
Derive rRK and rIK on EAP peer if ERP is enabled. The new wpa_supplicant
network configuration parameter erp=1 can now be used to configure the
EAP peer to derive EMSK, rRK, and rIK at the successful completion of an
EAP authentication method. This functionality is not included in the
default build and can be enabled with CONFIG_ERP=y.

If EAP authenticator indicates support for re-authentication protocol,
initiate this with EAP-Initiate/Re-auth and complete protocol when
receiving EAP-Finish/Re-auth.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-04 12:16:29 +02:00
Dmitry Shmidt
f34891a3af Return only full network line in list_networks
It makes more sense to truncate at line boundary especially with the new
LAST_ID parameter.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-12-03 22:31:53 +02:00
Vinit Deshpande
90903a77ef List all networks despite message limit of 4096 bytes
This change creates 'LIST_NETWORK LAST_ID=x' form to allow
retrieval of all networks saved in the system. Without this form,
only first few (whatever fills in first 4096 bytes) can be
retrieved.

Signed-off-by: Vinit Deshpande <vinitd@google.com>
2014-12-02 23:47:27 +02:00
Jouni Malinen
e374522827 Do not start new radio work on scan completion during ext work
Externally triggered scan could result in a new radio work item getting
started even when external radio work was in progress. Delay such start
until the external work is completed.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-12-01 20:17:08 +02:00
Jouni Malinen
fc0ef7c0e7 Add DATA_TEST_FRAME for testing Data frame processing
The new wpa_supplicant control interface command can be used in
automated testing to verify how AP processes Data frames with arbitrary
contents. This is enabled only in builds with CONFIG_TESTING_OPTIONS=y.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 23:51:46 +02:00
Jouni Malinen
b925506a91 Clear RSN preauth and PMKSA cache state on FLUSH command
There is no need for this state to maintained when the wpa_supplicant
FLUSH ctrl_iface command is used to request flushing of all state.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-11-27 19:56:15 +02:00
Assaf Krauss
4c4b230527 wpa_supplicant: Add an option to specify SSID in neighbor report requests
Allow supplying an SSID for the SSID IE. If not supplied, no SSID IE is
sent, and the request implies the current SSID.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:36:42 +02:00
Assaf Krauss
f4b8bfae15 wpa_supplicant: Add NEIGHBOR_REP_REQUEST command to the control interface
Add NEIGHBOR_REP_REQUEST command to the wpa_supplicant ctrl_iface.
This command triggers the sending of a Neighbor Report Request to the
associated AP.

Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
2014-11-22 21:28:52 +02:00
Moshe Benji
8506ea6f17 WMM AC: Add wmm_ac_status control interface command
This wmm_ac_status command will show the current status for WMM AC.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:40:51 +02:00
Moshe Benji
eb2f2088aa ctrl_iface: Add wmm_ac_addts and wmm_ac_delts commands
wmm_ac_addts command will add (or update) a traffic stream and
wmm_ac_delts command will delete an existing traffic stream.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 21:13:42 +02:00
Masashi Honma
0c6099f31b mesh: Check mesh key management method
Signed-off-by: Natsuki Itaya <Natsuki.Itaya@jp.sony.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Masashi Honma
790709060d mesh: Add scan result for mesh network
Android 4.4 uses "BSS" command instead of "SCAN_RESULT" command.
So this patch add the mesh scan result for BSS command.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-11-16 19:43:11 +02:00
Javier Lopez
603a3f34c4 Add mesh_group_{add,remove} control interface commands
Parse MESH_GROUP_ADD/REMOVE commands on ctrl interface and call
wpa_supplicant routines. These commands are used to start or
join and leave a mesh network.

The mesh id is given in the configuration file, therefore there is
no need to scan before joining a mesh network. We reuse the
connect_without_scan construct used by P2P for that same purpose.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
2014-11-16 19:43:11 +02:00
Jouni Malinen
666497c8e6 Suite B: Add AKM 00-0F-AC:11
This adds definitions for the 128-bit level Suite B AKM 00-0F-AC:11. The
functionality itself is not yet complete, i.e., this commit only
includes parts to negotiate the new AKM.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-11-16 13:20:51 +02:00
Sunil Dutt
477b082cc4 P2P: Do not consider the p2p_scan results after p2p_stop_find
If p2p_stop_find is issued after the p2p_scan request is triggered to
the host driver, the obtained scan results are also considered to update
the P2P peer entries. This is not always desired behavior, i.e., it can
be clearer if no P2P-DEVICE-FOUND events are generated based of that
final pending scan.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-31 00:50:01 +02:00
Ilan Peer
0a44358055 wpa_supplicant: Use the 'no_ir' notation
Use the 'no_ir' notation instead of the 'passive scan' and
'no_ibss' notations to match the earlier change in nl80211.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-10-26 01:23:43 +03:00
Jouni Malinen
1f94e4ee3e Add test functionality to simulate driver increased ROC duration
The extra_roc_dur parameter can now be used in CONFIG_TESTING_OPTIONS=y
builds to simulate driver behavior where the ROC duration gets increased
without user space request.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-25 21:46:38 +03:00
Thomas Pedersen
07cb45ccb2 mesh: Add no_auto_peer config option
Add no_auto_peer parameter, which controls wheter a station will
automatically initiate peering to another mesh peer that comes into
range.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:45:35 +03:00
Jason Abele
638d945679 mesh: Show [MESH] flag in scan results
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
2014-10-25 13:45:05 +03:00
Jason Abele
be6b29f63d Add SAE and FT/SAE into scan results info
These key management options were missing from the previous set of
parsed information in scan results.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
2014-10-25 13:45:01 +03:00
Jouni Malinen
5f797376f2 tests: Make RELOG command use global control interface
This allows RELOG to be used even if a wpa_supplicant process does not
have any interfaces configured.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-20 12:52:25 +03:00
Jouni Malinen
4a6cc86272 Add data test functionality
It is now possible to run hwsim_test like data connectivity test through
wpa_supplicant/hostapd control interface if CONFIG_TESTING_OPTIONS=y is
used for the build. Test functionality is enabled/disabled at runtime
with "DATA_TEST_CONFIG <1/0>". The "DATA_TEST_TX <dst> <src> <tos>"
command can be used to request a test frame to be transmitted.
"DATA-TEST-RX <dst> <src>" event is generated when the test frame is
received.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-19 20:51:45 +03:00
Jouni Malinen
9d4ff04af3 Add external EAPOL transmission option for testing purposes
The new ext_eapol_frame_io parameter can be used to configure hostapd
and wpa_supplicant to use control interface for receiving and
transmitting EAPOL frames. This makes it easier to implement automated
test cases for protocol testing. This functionality is included only in
CONFIG_TESTING_OPTIONS=y builds.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-10 18:40:57 +03:00
Toby Gray
45d8501555 Fix out of bounds memory access when removing vendor elements
Commit 86bd36f0d5 ("Add generic
mechanism for adding vendor elements into frames") has a minor bug
where it miscalculates the length of memory to move using
os_memmove. If multiple vendor elements are specified then this can
lead to out of bounds memory accesses.

This patch fixes this by calculating the correct length of remaining
data to shift down in the information element.

Signed-off-by: Toby Gray <toby.gray@realvnc.com>
2014-10-07 00:43:47 +03:00
Bojan Prtvar
b6ebdfbedd Extend STATUS command with frequency information
This makes 'wpa_cli status' command more versatile.

Signed-off-by: Bojan Prtvar <bojan.prtvar@rt-rk.com>
2014-09-28 20:47:06 +03:00
Jouni Malinen
c267753ba2 Add support for using random local MAC address
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.

This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.

This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.

The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 20:07:19 +03:00
Ahmad Kholaif
79e2b1cc54 Add PMKSA_FLUSH ctrl_iface command
"PMKSA_FLUSH" can now be used to flush PMKSA cache entries over the
control interface.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-27 10:44:22 +03:00
Dan Williams
7a4a93b959 dbus: Add SignalPoll() method to report current signal properties
Analogous to the control interface's SIGNAL_POLL request.

Signed-hostap: Dan Williams <dcbw@redhat.com>
2014-09-13 17:21:54 +03:00
vandwalle
a6ab82d7b4 Android: Add NO_EVENTS parameter to status command
It also allows to use the STATUS command with default behavior,
say for debug, i.e., don't generate a "fake" CONNECTION and
SUPPLICANT_STATE_CHANGE events with the new STATUS-NO_EVENTS case.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-09-13 17:03:16 +03:00
Jouni Malinen
0ef023e478 Add support for driver command to update roaming policy
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-11 15:59:42 +03:00
Jouni Malinen
71a0e395b9 P2P: Make unrecognized vendor elements available in P2P_PEER
This allows external programs to use vendor specific information from
P2P peers without wpa_supplicant having to be able to parse and
understand all such vendor specific elements.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-08 15:57:30 +03:00
Jouni Malinen
86bd36f0d5 Add generic mechanism for adding vendor elements into frames
This adds following new control interface commands to allow arbitrary
vendor elements to be added into number of frames:

VENDOR_ELEM_ADD <frame id> <hexdump of elem(s)>
VENDOR_ELEM_GET <frame id>
VENDOR_ELEM_REMOVE <frame id> <hexdump of elem(s)>
VENDOR_ELEM_REMOVE <frame id> *

The following frames are supported in this commit (additional frames can
be added in the future):

0 = Probe Request frame in P2P device discovery
1 = Probe Response frame from P2P Device role
2 = Probe Response frame from P2P GO
3 = Beacon frame from P2P GO
4 = PD Req
5 = PD Resp
6 = GO Neg Req
7 = GO Neg Resp
8 = GO Neg Conf
9 = Invitation Request
10 = Invitation Response
11 = P2P Association Request
12 = P2P Association Response

One or more vendor element can be added/removed with the commands. The
hexdump of the element(s) needs to contain the full element (id, len,
payload) and the buffer needs to pass IE parsing requirements to be
accepted.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-07 12:25:09 +03:00