Commit graph

588 commits

Author SHA1 Message Date
Deepthi Gowri
f65a239ba4 P2P: Add provision discovery failure event
Add provisional discovery failure ctrl_iface event
(P2P-PROV-DISC-FAILURE) to indicate to the application layer in case of
PD failure.

Signed-off-by: Deepthi Gowri <deepthi@codeaurora.org>
2012-04-17 19:44:13 +03:00
Jouni Malinen
5f482d55fd P2P: Allow immediate group idle timeout configuration
A special value p2p_group_idle=-1 can now be used to configure the P2P
group idle mechanism to terminate a P2P client group immediately on any
disconnection after the completion of the initial 4-way handshake.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 17:03:27 +03:00
Jouni Malinen
361cdf3400 P2P: Extend use of group formation timeout until end of 4-way handshake
Instead of relying on the P2P group idle timeout before the group
connection has been fully established, re-start the group formation
timeout in the end of the WPS provisioning step and clear it at the
successful completion of the initial 4-way handshake. This allows the
P2P group idle timeout to be set to a small value without triggering it
during the initial scan and connection attempt.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 17:01:15 +03:00
Jouni Malinen
205e6474a1 P2P: Fix p2p_connect join scan handler in error cases
wpa_drv_scan() may fail for the initial p2p_connect join scan request,
e.g., if the driver happened to be scanning at the time the new
operation was initialized. Previously, a special scan result handler was
registered regardless of whether the new scan was started. This could
result in partial scan results (e.g., from p2p_find social scan) from
being used as full results for join (or now more importantly for
p2p_connect auto) purposes. Fix this by registering the new scan result
handler only if wpa_drv_scan() returns success.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 16:13:14 +03:00
Jouni Malinen
b31be3a0fd P2P: Add automatic GO Negotiation vs. join-a-group selection
p2p_connect command can now be used with an optional "auto" parameter
to request wpa_supplicant to determine automatically whether to use
join-a-group operation (if the peer is operating as a GO) or group
formation. This makes it easier for external programs to handle
connection type selection by offloading this to wpa_supplicant. The
previously used p2p_connect join commands can be replaced with
p2p_connect auto to use this new mechanism.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-13 16:04:36 +03:00
Jouni Malinen
86ae2e8a42 P2P: Fix shared freq check and support AP mode validation
The previous commit did not use the correct pointer in all operations
and was specific to station mode interfaces. Fix and extend it to work
with AP/GO interfaces, too.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-04-08 20:42:45 +03:00
Jouni Malinen
4b15620609 P2P: Abort join-group operation if concurrent group cannot be supported
If the driver does not indicate support for multi-channel concurrency,
abort join-group operation if the end result would result in use of
multiple operating frequencies with the same radio.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-04-08 20:12:05 +03:00
Nirav Shah
103b8f4dea P2P: Disconnect P2P group on supplicant deinit
When a supplicant is deinited and shutting, disconnect from P2P groups.
This fixes a memory leak on variable dbus_groupobj_path on exiting
supplicant.

Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
2012-04-06 18:41:06 +03:00
Angie Chinchilla
eb6f8c2bd4 P2P: Fix crash for failure case when WSC PIN is entered incorrectly
When forming a P2P group using WSC PIN method, if the PIN is entered
incorrectly the P2P client supplicant instance will crash as a result
of cleanup happening on data that is still in use in a case where a
separate P2P group interface is used.

For example, here is the path for the first crash:
eap_wsc_process():
- creates struct wpabuf tmpbuf; on the stack
- sets data->in_buf = &tmpbuf;
- calls wps_process_msg()
- which calls wps_process_wsc_msg()
- which, in case WPS_M4: calls wps_fail_event()
- which calls wps->event_cb()
- wps->event_cb = wpa_supplicant_wps_event()
- wpa_supplicant_wps_event()
- wpa_supplicant_wps_event_fail()
- which calls wpas_clear_wps()
- which calls wpas_notify_network_removed()
- which calls wpas_p2p_network_removed()
- which calls wpas_p2p_group_formation_timeout()
- which calls wpas_group_formation_completed()
- which calls wpas_p2p_group_delete()
- which calls wpa_supplicant_remove_iface()
- which calls wpa_supplicant_deinit_iface()
- which calls wpa_supplicant_cleanup()
- which calls eapol_sm_deinit()
- ... which eventually uses the ptr data->in_buf to free tmpbuf, our
stack variable and then the supplicant crashes

If you fix this crash, you'll hit another. Fix it and then a segfault.
The way we're cleaning up and deleting data from under ourselves here
just isn't safe, so make the teardown portion of this async.

Signed-hostap: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-hostap: Nirav Shah <nirav.j2.shah@intel.com>
intended-for: hostap-1
2012-04-06 18:22:03 +03:00
Jouni Malinen
3fc14102f8 P2P: Remove client group on Deauthentication reason code 3
The GO can indicate that the P2P Group session is ending by sending a
Deauthentication frame with reason code 3 (Deauthenticated because
sending STA is leaving) based on P2P specification section 3.2.9. Use
this reason code to remove the P2P client group without waiting for the
group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-03 16:45:28 +03:00
Eliad Peller
3c29244eb7 P2P: Add deinit_p2p_cli op to clear P2P client driver state
On P2P group removal, the GO is deinitialized correctly (and the vif
mode is set back to sta in case of nl80211), but the P2P client mode
wasn't deinitialized, and the nl80211 vif stays in P2P client mode.

Add a new deinit_p2p_cli op (similar to deinit_ap), which currently only
sets the interface back to station mode.

Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
2012-04-01 21:41:23 +03:00
Johannes Berg
2d43d37ff2 DBus: Add ability to report probe requests
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).

As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.

A small test script is also included.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 21:14:48 +03:00
Johannes Berg
baf513d695 Pass signal strength through, fix units
The signal strength is currently never used as the only driver reporting
it is nl80211 which uses IEEE80211_RADIOTAP_DB_ANTSIGNAL which is never
populated by the kernel. The kernel will (soon) populate
IEEE80211_RADIOTAP_DBM_ANTSIGNAL instead though, so use that.

Also, since it was never really populated, we can redefine the signal
field to be in dBm units only.

My next patch will also require knowing the signal strength of probe
requests throughout the code (where available), so add it to the
necessary APIs.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 18:48:12 +03:00
Jouni Malinen
21d996f775 P2P: Add support for preferred channel list
p2p_pref_chan configuration parameter can now be used to set the
list of preferred channel for P2P GO Negotiation. This will be used
in the priority order if the peer does not support the channel we
are trying to use as the GO (configured operating channel or the
best 2.4 GHz/5 GHz channel) for the case where a forced channel is
not used.

p2p_pref_chan=<op class:channel>,...

For example:
p2p_pref_chan=81:1,81:2,81:3,81:4,81:5,81:6

This would configure 2.4 GHz channels 1-6 as the preferred ones with
channel 1 the most preferred option.

These configuration parameters can be set in wpa_supplicant.conf and
dynamically updated with "wpa_cli set <param> <value>".

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-29 21:28:34 +03:00
Jouni Malinen
8c472816fd P2P: Do not use group idle timeout during provisioning
Use the normal group formation timeout during the provisioning phase to
avoid terminating this process too early due to group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-27 18:04:06 +03:00
Jouni Malinen
f4329aa2d0 P2P: Validate p2p_oper_channel in p2p_group_add
If the p2p_group_add command does not specify the operating channel,
make sure the operating channel set in the configuration file meets
the P2P requirements in the same way as is done with the frequency
specified as the command parameter.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-26 22:06:48 +03:00
Jouni Malinen
10531d2166 P2P: Fix provisioning info clearing after successful WPS step
Previously, this provisioning info was cleared using the P2P Interface
Address of the GO as the key. That did not always work in the case the
where we joined an already running group. This could result in the next
connection to that same GO skipping provision discovery. Fix this by
finding the peer entry based on its P2P Device Address instead of the
P2P Interface Address which may not always be set.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
intended-for: hostap-1
2012-03-01 22:06:03 +02:00
Jouni Malinen
75c208b9db P2P: Fix p2p_cancel to return success if GO Negotiation is stopped
If a GO Negotiation peer is found, wpas_p2p_stop_find() stops the
negotiation and p2p_cancel can return success.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-03-01 01:16:06 +02:00
Jouni Malinen
8e64f258c6 P2P: Optimize provisioning step scan for join-a-group sequence
Copy the SSID and frequency of the selected group into go_params in
join-a-running-group case so that the scan optimization can be used for
the provisioning step similarly to the case of group formation. This
uses a specific SSID and a single channel scan to avoid unnecessary
frames during the step.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-29 00:22:58 +02:00
Jouni Malinen
360182ed7c P2P: Advertise immediate availability of WPS credential
Use Device Password ID in WSC IE of Probe Request and Probe Response
frames to advertise immediate availability of WPS credentials per P2P
specification sections 3.1.2.1.1 (Listen State), 3.1.2.1.2 (Scan Phase),
and 3.1.2.1.3 (Find Phase).

For now, the Device Password ID is set only for the case where we are
active GO Negotiation with a specific peer. In practice, this means that
the Probe Response frames during pending GO Negotiation (whenever in
Listen state) indicate availability of the credential.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-27 23:14:35 +02:00
Jouni Malinen
dddc70455b P2P: Add more debug on group idle timeout
This makes it easier to debug issues with P2P group idle timeout.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-19 18:16:34 +02:00
Jouni Malinen
a7a30b90e5 P2P: Fix group idle timer cancellation on group removal
The wpas_p2p_group_idle_timeout was getting cancelled in the beginning
of wpas_p2p_group_delete(). However, in the case of P2P client role,
this function called wpa_supplicant_deauthenticate() next and that ended
up changing state to WPA_DISCONNECTED which resulted in
wpas_p2p_notif_disconnected() rescheduling the timeout. This left the
unexpected timeout behind after the group was removed. If another group
operation was started within P2P_MAX_CLIENT_IDLE (10) seconds, that
timeout could end up terminating the group while it was still being set
up.

Fix this by reordering wpas_p2p_group_delete() to cancel the group idle
timeout only after having called wpa_supplicant_deauthenticate(). The
group idle timeout is still rescheduled, but it gets removed immediately
afterwards when the actual group information is being cleared.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-19 18:10:20 +02:00
Jouni Malinen
6f3bc72be0 P2P: Allow channels to be removed from P2P use
A list of disallowed frequencies for P2P channel list can now be
configured with P2P_SET disallow_freq. The frequencies (or frequency
pairs) are comma separated. For example:
wpa_cli p2p_set disallow_freq 2462,5000-6000

The allowed P2P channel list is constructed by removing explicitly
disallowed channels from the channel list received from the driver.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-02-17 22:57:13 +02:00
Jouni Malinen
e22d4d957b Remove the GPL notification from files contributed by Atheros
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-11 19:39:36 +02:00
Piotr Nakraszewicz
d9a0f66696 P2P: Do not expire GO peer entry during group rekeying
If wpas_go_connected() is called during group rekeying the P2P GO peer
will expire. To prevent that check if group rekeying is not in progress.
2012-02-11 10:54:40 +02:00
Jouni Malinen
c427ac9211 P2P: Set Invitation Type to 1 for GO inviting to a persistent group
When a GO is operating a persistent group and invites a peer that has
been a P2P client in that persistent group, the Invitation Type in the
Invitation Request frame can be set to 1 to indicate that this is a
reinvocation of a persistent group. Do this based on the maintained
list of P2P clients that have been provided the credentials to this
group.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-06 21:54:36 +02:00
Jouni Malinen
f63b854215 P2P: Wait for PD-before-join response
Even though the Provision Discovery Response frame from PD-before-join
does not really provide any additional information, it can be better to
wait for it before starting the join operation. This adds a minimal
extra latency in the most common case and cleans up the sequence of
driver operations and debug log by avoiding potential processing of the
Provision Discovery Response while already running a scan for the actual
connection.

If transmission of Provision Discovery Request fails, join operation is
started without the additional wait. In addition, a new timeout is used
to start the join if Provision Discovery Response is lost for any
reason.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-05 20:52:24 +02:00
Jouni Malinen
c19316354e P2P: Skip event notification on PD Response in join-group case
Provision Discovery is used as a notification to the GO in the case we
are about join a running group. In such case, there is not much point in
indicating the provision discovery response events to external programs
especially when the PIN-to-be-displayed was different from the one
returned for the p2p_connect command. Skip this confusing event
completely for join-a-running-group case.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-05 20:20:36 +02:00
Dmitry Shmidt
df509539d4 Let wpa_supplicant_deinit_iface() know that process is terminating
This will be needed to be able to move ctrl_iface TERMINATING event to
the end of interface removal.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2012-01-29 20:15:48 +02:00
Jouni Malinen
b1aebbc427 P2P: Do not expire peer entry if we are connected to the peer
Even though we may not update P2P peer entry while connected to the
peer as a P2P client, we should not be expiring a P2P peer entry while
that peer is the GO in a group where we are connected as a P2P client.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-01-25 17:27:47 +02:00
Jouni Malinen
433cd2ce65 Stop sched_scan in number of cases where it should not be running
When a P2P group is removed, we better not leave possibly started
sched_scan running. This could happen when a separate group interface
was not used.

In addition, it looks safer to explicitly stop sched_scan before
starting P2P Listen or Find operations to make sure the offloaded
scanning is not running when doing similar P2P operations.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-01-23 18:26:09 +02:00
Jouni Malinen
6d92fa6e92 P2P: Allow Device ID to be specified for p2p_find command
dev_id=<P2P Device Addr> can now be specified as an argument to
p2p_find to request P2P find for a specific P2P device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-01-08 09:25:29 -08:00
Jouni Malinen
e91829f9ac P2P: Stop remain-on-channel prior to starting join-a-group client
This fixes issues with drivers that do not handle concurrent
remain-on-channel and scan operations in a case where Provision
Discovery Response frame is not received to stop the Action frame
handshake.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-29 13:28:17 +02:00
Neeraj Kumar Garg
b8349523e4 P2P: Reject p2p_group_add if forced frequency is not acceptable
If the freq parameter is specified and we are already running legacy STA
on a different frequency with a driver that does not support
multi-channel concurrency, reject p2p_group_add. Same code already
exists in the path of P2P connection with go negotiation but is missing
for autonomous GO.

Signed-hostap: Neeraj Garg <neerajkg@broadcom.com>
2011-12-27 23:21:45 +02:00
Jouni Malinen
d7e70476f2 P2P: Use global->p2p_dev_addr instead of parent->own_addr
Start using global->p2p_dev_addr more consistently as the P2P Device
Address.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-25 23:58:03 +02:00
Jouni Malinen
fbdcfd577a P2P: Maintain a list of P2P Clients for persistent group on GO
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-22 22:47:41 +02:00
Jouni Malinen
87f841a140 P2P: Show persistent group info on P2P_PEER data
Add "persistent=<network id>" line to P2P_PEER ctrl_iface data
if a persistent group credentials are available for this peer.
This makes it easier for external programs to figure out when
a persistent group could be re-invoked with this peer.

For now, this information is only available on the P2P client,
but similar information can be added for GO once a list of P2P
clients is maintained with the persistent group data.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-22 21:45:20 +02:00
윤민홍
3b655312d4 P2P: Send D-Bus ServiceDiscoveryRequest signal for external SD processing
wpas_notify_p2p_sd_request() needs to be called when
p2p_sd_over_ctrl_iface is set to provide SD events over D-Bus similarly
to the ctrl_iface events.
2011-12-22 00:34:29 +02:00
Jouni Malinen
c81066153c P2P: Use hardcoded idle timeout of 10 seconds in P2P client role
The p2p_group_idle configuration parameter is much more useful for
GO role, so use a separate hardcoded value of 10 seconds in P2P
client role. In practice, this means that the P2P client role will
automatically tear down the group when the GO tears down the group.

The 10 second timeout is enough to recover from temporary disconnections
without unnecessary tearing down the group if the GO is still present
and allows the client to connect.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 22:21:22 +02:00
Jouni Malinen
4c2c675173 P2P: Fix disconnect event not to increase idle timeout
When P2P client is processing a disconnection event, make sure the P2P
idle timeout does not get increased, i.e., set a new timeout only if no
timeout is in use. wpa_state changes between DISCONNECTED and SCANNING
can generate multiple calls to wpas_p2p_notif_disconnect() and
previously this was enough to force the idle timeout never hit in
practice when in P2P client role.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 22:18:42 +02:00
Jouni Malinen
1ef2f7ffcf P2P: Fix Provision Discovery channel for some join-GO cases
The Provision Discovery Request needs to be sent on the operating
channel of the GO and as such, the frequency from the BSS table
(scan results) need to override the frequency in the P2P peer
table that could be based on the Listen channel of the GO.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-18 17:21:25 +02:00
Reinette Chatre
e5a359cf7e P2P: Make GO negotiation peer and group information available over D-Bus
The GO negotiation response is very cryptic at the moment. For a success
message we only know on which interface the negotiation succeeded, not
which peer. For a failure we know the interface also and a status code
(number).

It will be very useful for clients to know upon receipt of such a message
which peer the negotiation occurred with.

Now that the peer information is available and the API is changed
already, the function composing the D-Bus message might as well include
all GO negotiation information. This is done with a dict to make things
easier on clients if this result information changes down the line.

Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-12-18 16:52:33 +02:00
Jouni Malinen
5506d18418 Fix compiler warning with CONFIG_NO_STDOUT_DEBUG=y
Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:19:24 +02:00
Jouni Malinen
7165c5dc1f P2P: Fix 32-bit compiler warnings on service discovery reference
Convert core wpa_supplicant code to use u64 instead of void * for the
P2P service discovery reference. Use uintptr_t in type casts in
p2p_supplicant.c to handle the conversion without warnings.

Note: This needs to be revisited for 128-bit CPU where sizeof(void *)
could be larger than sizeof(u64).

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 18:06:34 +02:00
Jouni Malinen
e3a0706b47 P2P: Fix Provision Discovery name in debug messages
Some debug messages used incorrect name for Provision Discovery.
Replace "Provisioning Discovery" with "Provision Discovery".

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-11 17:36:38 +02:00
Vitaly Wool
c3daaf3325 Skip WPS PBC overlap detection if P2P address is the same
WPS overlap detection can detect false overlap if a P2P peer
changes UUID while authentication is ongoing. Changing UUID
is of course wrong but this is what some popular devices do
so we need to work around it in order to keep compatibility
with these devices. There already is a mechanism in WPS
registrar to skip overlap detection if P2P addresses of two
sessions match but it wasn't really triggered because the
address wasn't filled in in the caller function.

Let's fill in this address and also clean up WPS PBC sessions
on WSC process completion if UUID was changed.

Signed-hostap: Vitaly Wool<vitalywool@gmail.com>
2011-12-11 12:03:18 +02:00
Jouni Malinen
502618f7c1 P2P: Clean up group formation on network block removal
If a P2P group network block is removed for any reason (e.g., wps_cancel
command) while the interface is in group formation, remove the group
formation timeout and indicate failure immediately. Previously, this
type of operations could end up leaving the timeout running and result
in somewhat unexpected group formation failure events later.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-10 12:56:42 +02:00
Jouni Malinen
c3f4278445 P2P: Add group ifname to P2P-PROV-DISC-* events
If Provision Discovery Request is sent for GO role (i.e., P2P Group ID
attribute is included), add the group interface name to the control
interface event on the GO. This makes it easier to figure out which
ctrl_iface needs to be used for wps_pbc/wps_pin command to authorize
the joining P2P client.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-06 21:57:17 +02:00
Jithu Jance
ec437d9e74 P2P: Skip duplicated provision discovery on join
If p2p_prov_disc join command is used prior to p2p_connect join,
skip the duplicated provision discovery exchange.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2011-12-06 21:44:57 +02:00
Jithu Jance
8c5f730983 P2P: Add optional "join" argument for p2p_prov_disc command
This can be used to request Provision Discovery Request to be sent
for the purpose of joining a running group, e.g., to request the GO
to display a PIN that we can then use with p2p_connect join command.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2011-12-06 21:28:02 +02:00
Jouni Malinen
a9e02d593d P2P: Clear show_group_started on GO start
The show_group_started variable could be left to 1 based on an earlier
failed attempt to start P2P client operation. This can result in
unexpected P2P-GROUP-STARTED event when a GO is started without group
formation (e.g., re-invoke a persistent group or start an autonomous
GO). Avoid this by explicitly clearing show_group_start when setting up
the GO.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-12-01 10:49:26 +02:00
Jouni Malinen
9dbf53fe35 P2P: Send Listen state Probe Response frames without retries
Use the no-ACK send_mlme request to transmit Probe Response frames
in P2P Listen state. This reduces number of unnecessary transmissions
if the peer device has already moved away from the channel. It will most
likely go through Search state multiple times anyway, so even if the
response were to be lost, a new retry will happen at higher layer.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-19 19:15:10 +02:00
Johannes Berg
6cad95db72 P2P: Simplify code in wpas_p2p_connect()
There's some duplicated code there that can be simplified
with just a single new variable.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-11-18 23:32:03 +02:00
Jouni Malinen
19df9b0761 Mark local functions static
These functions are not used outside the file in which they are defined.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-11-18 21:53:36 +02:00
Jouni Malinen
2bb747e232 P2P: Cancel previous operation before starting new p2p_listen
Some drivers do not handle concurrent remain-on-channel operation
requests, so run p2p_stop_find() prior to starting p2p_listen. This
addresses some issues with P2P_LISTEN command being issues again
while already in Listen state.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-17 16:21:11 +02:00
Jouni Malinen
39185dfa54 P2P: Wait until ongoing scan completes before starting P2P find
The P2P_FIND command was failing if it was issued at the moment when
a scan operation was in progress. Avoid returning failure in this
case by scheduling the P2P find to start once the ongoing scan is
completed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-15 21:28:35 +02:00
Jouni Malinen
adc33680e3 Do not add P2P IE into Beacon/Probe Response if P2P is disabled
P2P IE was incorrectly added in wpa_supplicant AP mode even if P2P
function was not actually enabled.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2011-11-14 16:26:45 +02:00
Jouni Malinen
97bcd562eb Remove disable_11b_rates() driver_ops
This function was used unconditionally if wpa_supplicant build
includes CONFIG_P2P=y. Adding a separate driver_ops for such use
is not really useful since the driver wrappers can do the same
internally. Remove this driver_ops and move matching functionality
into driver_nl80211.c which was the only driver wrapper using
this driver_ops callback.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-29 22:25:28 +03:00
Jouni Malinen
b106173a82 Add no_cck parameter for send_action() driver_ops
This can be used to apply the no-CCK rule conditionally depending on
which frame is being sent. The no-CCK rule applies only for P2P
management frames while SA Query and FT use cases do not have similar
restrictions.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-10-29 21:49:46 +03:00
Jithu Jance
b49d6ccb74 P2P: Fix frequency in the P2P_EVENT_GROUP_STARTED event
P2P Client did not show correct frequency in the control interface
event P2P_EVENT_GROUP_STARTED. Fix that by using the frequency from
the BSS table or association event.
2011-10-28 22:26:30 +03:00
Jithu Jance
3074d8f12d P2P: Notify device expiry via P2P-DEVICE-LOST event
This patch will notify applications listening over control socket about
the device expiry [from p2p peer list].
2011-10-28 22:13:18 +03:00
Jithu Jance
2d4f15d683 P2P: Stop any on-going "p2p_find" on creating an Autonomous GO
This patch stops any on-going "p2p_find" on creating an Autonomous GO.
This is already taken care in case of invoking a persistent GO. GO as
such will be advertising via the beacons for other devices to discover.
So normally the GO doesn't need to do a p2p_find until and unless it
wants to invite a P2P Client. In case of Invite scenario, logically it
is better to do a explicit discover [via user intervention] after the GO
is created. This patch will help to reduce battery wastage [due to
p2p_find operations] in scenarios where user creates a GO and doesn't
initiate a connection.
2011-10-26 01:28:51 +03:00
Jouni Malinen
acc247b260 P2P: Advertise Persistent Reconnect group capability
The persistent_reconnect configuration parameter was used to decide
whether to accept invitation to re-establish a persistent group.
However, this was not being advertised in the Group Capability bitmap.
Add the Persistent Reconnect bit based on this configuration to GO
Negotiation frames and Beacon/Probe Response frames from the GO.
2011-10-24 17:29:37 +03:00
Christian Lamparter
6bf731e8ce wpa_supplicant: Unify hardware feature data
The hardware feature data is required in several different places
throughout the code. Previously, the data was acquired and freed on
demand, but with this patch wpa_supplicant will keep a single copy
around at runtime for everyone to use.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2011-10-23 17:21:50 +03:00
Jouni Malinen
17fbb751e1 Remove user space client MLME
This code was used only with driver_test.c to allow MLME operations
in hostapd to be tested without having to use a real radio. There
are no plans on extending this to any other use than testing and
mac80211_hwsim has now obsoled the need for this type of testing.
As such, we can drop this code from wpa_supplicant to clean up the
implementation of unnecessary complexity.
2011-10-22 22:45:38 +03:00
Janusz Dziedzic
a7fd39bb5d P2P: Cleanup AP callbacks when removing the group
Clear the P2P GO callback parameters when removing the group to avoid
using these for non-P2P AP mode.

This is a fix for the bug I found in the following scenario:

A) p2p_group_add
A) p2p_group_remove wlan0
A) add_n
A) set_n 0 ssid "testap"
A) set_n 0 key_mgmt NONE
A) set_n 0 mode 2
A) set_n 0 frequency 2412
A) enable_n 0

B) try connect to testap

Authentication request will be always rejected because of
HOSTAPD_ACL_REJECT and not cleaned callbacks when group removed.
2011-10-12 21:06:39 +03:00
Jouni Malinen
24f6497c34 GAS: Use off-channel operations for requests
This separates off-channel Action frame TX/RX from P2P into a generic
implementation that can now be used both for P2P and GAS needs.
2011-09-29 22:19:51 +03:00
Jouni Malinen
206e1f422f P2P: Provide mechanism for figuring out p2p_scan_ie() buffer need
The new function, p2p_scan_ie_buf_len(), can be used to figure out
how large a buffer needs to be allocated for p2p_scan_ie() use. This
makes it easier to add new data into the buffer without forcing all
callers to be updated to use a larger buffer.
2011-09-29 22:18:23 +03:00
Jouni Malinen
303f60d39b P2P: Do not request station mode scans during P2P operations
The P2P search mechanism depends on the same scan functionality that
is used for station mode scans. If these operations are being used
at the same time, scan result processing is not handled properly.
Avoid unexpected behavior by delaying station mode scan requests
if a P2P operation is in progress.

Among other things, this allows the station mode connection attempt
to be continued after a P2P find or group formation has been completed
if the interface is available (i.e., when the P2P group uses a
separate virtual interface).
2011-09-29 16:53:55 +03:00
Jouni Malinen
0c96fd6d03 P2P: Do not leave P2P scan handler registered if scan fails
If the initial attempt to start a scan for p2p_find fails, an error
is reported. However, the P2P scan handler and search state was
left behind. That can result in unexpected behavior when the next
non-P2P scan results are indicated. Avoid this by clearing the
P2P search state on failure.
2011-09-29 16:52:23 +03:00
Johannes Berg
3a26a2c9df P2P: Fix action done handling for driver-based off-channel TX
The action done handling needs to abort an off-channel period since one
might have been used for example for GO negotiation and after action
done the code assumes it can start a new off-channel period.

This fixes a bug I introduced when adding support for
in-kernel off-channel transmissions.

Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-09-22 00:57:27 +03:00
Rajkumar Manoharan
47185fc788 P2P: Remove CCK supported rates when running P2P scan
This allows drivers to disable CCK rates from Probe Request frames.
For nl80211, this is currently applying only to the supported rates
element(s), but this mechanism could be extended to address TX rate
control masking, too, to lessen need for global rate disabling.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
2011-09-10 22:40:30 +03:00
Jouni Malinen
07fecd3915 P2P: Remove Label config method
The P2P specification (3.1.4.3) disallows use of the Label configuration
method between two P2P devices. This was previously enforced at upper
level, but the obsolete code can be removed from wpa_supplicant. This
adds a bit more strict enforcement of the policy, but should not result
in practical differences since no known P2P implementation uses Label
config method.
2011-09-08 16:40:03 +03:00
Jouni Malinen
04a85e4401 P2P: Filter Probe Request frames based on DA and BSSID in Listen state
Only accept Probe Request frames that have a Wildcard BSSID and a
destination address that matches with our P2P Device Address or is the
broadcast address per P2P specification 3.1.2.1.1.
2011-07-15 20:28:46 +03:00
Jouni Malinen
21fe9e757e P2P: Use consistent checking of ssid != NULL 2011-07-15 14:20:31 +03:00
Jouni Malinen
ab1dee81a2 P2P: Remove dead code from wpas_p2p_connect()
The case of joining a running group is handled before this location
and the P2P client iftype is assigned at a callback function for that
case.
2011-07-15 13:57:31 +03:00
Jouni Malinen
20a0b03deb Clear WPA and EAPOL state machine config pointer on network removal
Make sure that the WPA and EAPOL state machines do not hold a pointer
to a network configuration that is about to be freed. This can fix
potential issues with references to freed memory.
2011-06-27 19:02:24 +03:00
Jayant Sane
2463ba70e2 P2P: Update listen and operating channel from P2P D-Bus
Some P2PDevice properties were not updated in p2p->cfg structure:
reg_class, channel, op_reg_class, and op_channel. Hence, update p2p->cfg
parameters through p2p core calls in wpas_p2p_update_config().

Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-25 12:08:43 +03:00
Jayant Sane
3734552f15 P2P: Add WpsFailed signal in P2P D-Bus
Signal is triggered if an error occurs during WPS provisioning phase.

Signed-off-by: Jean-Michel.Bachot <jean-michelx.bachot@intel.com>
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-25 11:47:04 +03:00
Jayant Sane
c2762e410f P2P: Update D-Bus network object semantics during group formation
Do not emit network objects during P2P group formation since such
network objects can confuse certain apps. Instead, a persistent group
object is created to allow apps to keep track of persistent groups.
Persistent group objects only represent the info needed to recreate the
group.

Also fixes a minor bug in the handling of persistent group objects
during WPS operations.

Signed-off-by: Jayant Sane <jayant.sane@intel.com>
2011-06-23 21:25:13 +03:00
Jouni Malinen
7dcdcfd68d P2P: Start GO without extra scan step
There are some corner cases, where the wpa_supplicant_req_scan() call
may end up scheduling a scan even if we are about to start a GO. Avoid
this by explicitly marking the GO network to be selected for the next
connection.
2011-06-21 11:47:03 +03:00
Jean-Michel Bachot
4b6baa2f5e P2P: Add group started notification
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-06-12 14:35:37 -07:00
Johannes Berg
dd8a7e0547 P2P: Add wpas_notify_p2p_provision_discovery()
Add a notification for P2P provision discovery status/result.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-06-12 14:31:56 -07:00
Jouni Malinen
64f992652d P2P: Include operating class 124 (channels 149,153,157,161)
When using the p2p_oper_reg_class configuration option instead of
p2p_group_add freq parameter, the operating class 124 was not
processed correctly. Include that class in the list of 5 GHz classes
for the p2p_oper_reg_class to resolve this.
2011-05-16 21:07:05 +03:00
Jouni Malinen
714b8b5378 P2P: Fix memory leak in UPnP service discovery request processing 2011-04-14 01:33:26 +03:00
Jouni Malinen
62c0d27ed3 P2P: Clear go_dev_addr for group started events if it is not known
Better make sure the address value included in the event message gets
cleared in case the GO Device Address is not known for some reason.
Previously, this could potentially have been some random data from
stack should we ever hit the case where wpa_s->current_ssid is not
set (which should not really happen in normal use cases).
2011-04-13 22:03:52 +03:00
Jouni Malinen
b6e0180035 P2P: Add more WPS attributes into Listen state Probe Response
Configure more WPS attributes in the P2P module and use them
when generating WSC IE for Probe Response frames in Listen state.
2011-03-28 15:24:12 +03:00
Jean-Michel Bachot
046ef4aa67 P2P: Add option for requested device type in P2P search/scan
With this, p2p_find can be extended to find certain requested device
types.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-19 12:57:46 +02:00
Jean-Michel Bachot
f95cac271b P2P: Allow adding of WPS vendor extension attributes
This adds the ability to add WPS vendor extension attributes in P2P
frames, like GO Negotiation and Probe Response frames.

Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-19 12:22:18 +02:00
Johannes Berg
2f646b6e83 WPS: Store (secondary) device type as binary
Instead of converting back and forth from the string representation,
always use the binary representation internally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-03-17 18:50:22 +02:00
Jouni Malinen
e17a2477db nl80211: Extend bridge add/del operations for secondary BSSes
Previously, only the main interface was added to a bridge. Extend this
to apply to all configured BSSes.
2011-03-15 13:02:49 +02:00
Konguraj(Raj) Kulanthaivel
43a26f606c P2P: Add wpas_notify_p2p_sd_response
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:47:34 +02:00
Konguraj(Raj) Kulanthaivel
e1653cac23 P2P: Add wpas_notify_p2p_sd_request
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:45:39 +02:00
Jean-Michel Bachot
5ccdf84f0d P2P: Add invitation result notification
Add a notification function for the result of an invitation.

Signed-off-by: Jean-Michel Bachot <jean-michelx.bachot@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:40:21 +02:00
Jayant Sane
c2641bf7cf P2P: Add GO negotiation status notification
Signed-off-by: Jayant Sane <jayant.sane@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:34:52 +02:00
Konguraj(Raj) Kulanthaivel
32d1bce0c0 P2P: Add wpas_notify_p2p_go_neg_req
Add a notification for received GO negotiation requests.

Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:30:19 +02:00
Johannes Berg
408af93ed4 P2P: Add group removed notification
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:27:23 +02:00
Johannes Berg
56eeb8f299 P2P: Add method to signal lost device
This signal is used to notify users of the P2P
state machine or wpa_supplicant of lost devices.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:22:16 +02:00
Johannes Berg
d642d2d267 P2P: Add notification for P2P device found
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 22:08:18 +02:00
Johannes Berg
8fd7dc1b1c P2P: Add new_device flag to dev_found callback
The DBus code will want to have perfect matching of dev_found and the
dev_lost it adds so it doesn't need to keep track internally. Enable
that with a new flag in the core that tracks whether we have already
notified about this -- the existing users can ignore it.

The part where this is always set to 1 if the new device is discovered
by a driver that has P2P in the driver is buggy -- the driver should
feed the P2P peer database and then that should feed the notification
here instead.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 21:59:58 +02:00
Konguraj(Raj) Kulanthaivel
c5db8e5170 P2P: Embed publically visible struct in peer info
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.

The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.

Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-24 21:51:17 +02:00
Jouni Malinen
9526fd293f P2P: Handle P2P-not-supported without segfaults
Previous code was assuming that the P2P module is always initialized.
However, that is not the case anymore with drivers that do not support
P2P. Add verification of whether P2P is enabled before trying to execute
P2P commands.
2011-02-24 21:13:30 +02:00
Jouni Malinen
d601247ca9 P2P: Allow WPS_PBC command on GO to select on P2P Device Address
An optional parameter, p2p_dev_addr, can now be given to WPS_PBC
command on P2P GO to indicate that only the P2P device with the
specified P2P Device Address is allowed to connect using PBC. If
any other device tries to use PBC, a session overlap is indicated
and the negotiation is rejected with M2D. The command format for
specifying the address is "WPS_PBC p2p_dev_addr=<address>", e.g.,
WPS_PBC p2p_dev_addr=02:03:04:05:06:07

In addition, show the PBC session overlap indication as a WPS failure
event on an AP/GO interface. This particular new case shows up as
"WPS-FAIL msg=4 config_error=12".
2011-02-07 18:28:36 +02:00
Johannes Berg
3103f34576 P2P: Add wpas_p2p_disconnect()
Add a new API function wpas_p2p_disconnect()
to disconnect from or dissolve a group.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-02 17:30:15 +02:00
Johannes Berg
bbeee9b0db P2P: Use a variable for generated PIN to allow multiple uses
In order to pass the same PIN to multiple notifications in the future,
generate it centrally.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-02 17:12:37 +02:00
Johannes Berg
d1c8ac88b9 DBus: Publish provisioned keys in network properties
When the network was provisioned, we need to get the keys to be able to
reconnect without new provisioning. To be able to publish those keys but
not normally configured ones, add a new attribute to struct wpa_ssid
indicating whether or not keys may be exported.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-02 17:00:12 +02:00
Johannes Berg
839b33ad90 P2P: Clear driver Probe Response IE on stop_listen
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-01 18:30:33 +02:00
Johannes Berg
11fb02be67 P2P: Fix p2p_long_listen
There are two issues with p2p_long_listen:
 1) max_remain_on_channel is assumed to be 5 seconds,
 2) if max_remain_on_channel is not a full multiple of
    seconds, accounting breaks.

Fix these by converting p2p_long_listen to ms and
tracking it according to max_remain_on_channel.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2011-02-01 18:09:38 +02:00
Jouni Malinen
3ac17eba31 P2P: Add initial support for driver-based P2P management
This adds partial callbacks and events to allow P2P management to be
implemented in a driver/firmware. This is not yet complete and is
very much subject to change in the future.
2010-12-30 12:48:55 +02:00
Johannes Berg
190b9062b2 P2P: Add option for offloading off-channel TX to the driver
With the new kernel functionality coming to Linux to allow off-channel
TX, we can take advantage of that in the P2P code that currently uses
remain-on-channel. If a driver advertises support for it, it will be
asked to handle off-channel TX by itself.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-12-29 13:59:17 +02:00
Sudhakar Swaminathan
45fee6f090 P2P: Cancel group formation timeout on p2p_cancel 2010-12-17 15:06:48 +02:00
Sudhakar Swaminathan
231bbd0375 P2P: Unauthorize pending P2P GO Neg peer on p2p_cancel
If there is a pending GO Negotiation when p2p_cancel is used,
unauthorize the peer to avoid immediate reconnection from being
accepted without a new p2p_connect command.
2010-12-17 15:05:35 +02:00
Sudhakar Swaminathan
0a14e3ec8b P2P: Cancel group formation on PBC overlap
We should cancel group formation completely on PBC overlap instead
of just partially notifying that operations were stopped. There is
no point in waiting for the group formation timeout in this case.
2010-12-17 15:04:14 +02:00
Jouni Malinen
971e357f19 P2P: Add new driver option for interface allocation
WPA_DRIVER_FLAGS_P2P_MGMT_AND_NON_P2P flag can now be used to
indicate that the initial interface (e.g., wlan0) is used for
P2P management operations and potentially non-P2P connections.
This is otherwise identical to
WPA_DRIVER_FLAGS_P2P_DEDICATED_INTERFACE, but the possibility of
non-P2P connections makes some operations differ.
2010-11-26 15:52:16 +02:00
Jouni Malinen
a1eca5cfd8 P2P: Rename the group interface name to use p2p- prefix
This may make it less likely for udev to rename the interface that
would previously have been called wlan0-p2p-# (now: p2p-wlan0-#).
In addition, add some workaround code to handle the case where the
main interface name is close to the IFNAMSIZ length limit to
avoid going over that for the P2P group interface.
2010-11-26 15:50:22 +02:00
Sudhakar Swaminathan
9d562b7946 P2P: Add p2p_unauthorize command
This can be used to remove authorization from a previous p2p_connect
commands that has not yet resulted in completed GO Negotiation.
2010-11-25 13:09:50 +02:00
Jouni Malinen
ab72eb5256 P2P: Accept invitations to already running persistent group
We can automatically accept invitations that are for a persistent
group that is already running. There is no need to confirm this
separately or preparare a new group interface.
2010-11-19 12:58:31 +02:00
Jouni Malinen
9d39057c2b P2P: Stop p2p_find/p2p_listen when Invitation is accepted
When an Invitation to reinvoke a persistent group is accepted,
we need to make sure that any pending p2p_find or p2p_listen
operation gets stopped to avoid consuming all radio resources
doing device discovery while the group is being set up.
2010-11-19 12:58:03 +02:00
Jouni Malinen
6c0da49f62 P2P: Do not start multiple copies of same persistent group
When running p2p_group_add persistent=<id>, verify whether the
requested group is already running and if so, do not try to
start another copy of it.
2010-11-19 12:57:36 +02:00
Jouni Malinen
d1b024c9e5 P2P: Make sure wpa_s->global->p2p_group_formation gets cleared
This pointer is now used in number of places to check whether an
interface is in P2P Group Formation, so we better make sure it gets
cleared when group formation has been completed. This was done in
only some of the cases.
2010-11-18 12:41:27 +02:00
Jouni Malinen
bb79dc720b P2P: Fix invitation-to-running-group handling
The pending_invite_ssid_id of -1 (running group, not persistent) was
being stored incorrectly in the group interface, not device interface
(i.e., parent of the group interface) and consequently, the incorrect
information was used when processing the Invitation Response.

If there was a persistent group credentials stored with network id
0, those were used instead to try to set up a persistent group
instead of using the already running group.
2010-11-16 15:22:06 +02:00
Albert Liu
5496062919 P2P: Update pending join interface address during scans
Since the P2P peer entry may not have been available at the time the
join request was issued, we need to allow the P2P Interface Address
to be updated during join-scans when the P2P peer entry for the GO
may be added.
2010-11-15 16:16:39 +02:00
Jouni Malinen
9b1ab931b1 P2P: Allow multiple scan runs to find GO for p2p_connect join
If the GO is not found, we cannot send Provisioning Discovery Request
frame and cannot really connect anyway. Since the Provisioning
Discovery is a mandatory part, it is better to continue join-scan
until the GO is found instead of moving to the next step where
normal connection scan is used (PD would not be used from there).

Use a limit of 10 scan attempts for p2p_connect join to avoid getting
in infinite loop trying to join. If the GO is not found with those
scans, indicate failure (P2P-GROUP-FORMATION-FAILURE) and stop the
join attempt.
2010-11-15 16:15:38 +02:00
Jean Trivelly
01d92811f9 P2P: Add network_added notification when p2p device becomes GO
Notification is done when you become P2P client but was missing
when you become GO.

Signed-off-by: Jean Trivelly <jeanx.trivelly@linux.intel.com>
2010-11-12 21:21:24 +02:00
Jouni Malinen
5254eb7e50 P2P: Fix HT40 secondary channel validation 2010-11-12 19:04:48 +02:00
Jouni Malinen
5122242925 P2P: Add HT40 operating classes based on driver channel flags
This allows P2P to negotiate HT40 channels. For now, only 5 GHz
HT40 operating classes are enabled.
2010-11-12 18:14:12 +02:00
Jouni Malinen
148bb37f2e P2P: Send WPS-OVERLAP-DETECTED also to the parent interface
When running "p2p_connect addr pbc join" command, send the
WPS-OVERLAP-DETECTED even also to the parent interface (i.e.,
the one on which the p2p_connect was issued) and not only the
group interface in case separate P2P group interfaces are used.
2010-11-12 11:30:58 +02:00
Jouni Malinen
aaca650540 P2P: Replace the default country with "XX" (non-country entity) 2010-11-10 16:22:22 +02:00
Anil Gathala Sudha
7cfc4ac319 P2P: Add support for automatic channel selection at GO
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.

p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
2010-11-10 13:33:47 +02:00
Jouni Malinen
09d660b9e3 P2P: Clear off_channel_freq when requesting new remain-on-channel
The driver may end up leaving the current channel when we request
a new remain-on-channel and as such, it is better not assume we can
start new operations like sending an Action frame on the previous
off-channel.
2010-11-05 18:39:42 +02:00
Jouni Malinen
8eada5ca13 P2P: Cancel pending remain-on-channel request when stopping Listen
If we have already asked the driver to start a new remain-on-channel,
we need to cancel it even if the actual remain-on-channel has not yet
started at the point when a new operation or timeout etc. triggers
Listen state to be stopped.
2010-11-05 18:39:15 +02:00
Jouni Malinen
9bcf9541a7 P2P: Do not skip call to p2p_scan_res_handled()
Even if p2p_scan_res_handler() returns 1 to indicate that scan result
iteration should be stopped, the p2p_scan_res_handled() needs to be
called to clear p2p_scan_running and to get a callback that will start
any operations that were delayed because of the running scan.
2010-11-05 18:17:42 +02:00
Jouni Malinen
b029bd33c4 P2P: Copy p2p_intra_bss setting to the group interface
This is needed to allow p2p_intra_bss take effect when using
separate group interfaces.
2010-11-04 16:53:09 +02:00
Jouni Malinen
a0a9f3b02f P2P: Allow p2p_cancel to cancel P2P client that has not yet connected
This can now be used to cancel a P2P client interface that has not
yet completed the first 4-way handshake with a GO.
2010-11-04 11:59:44 +02:00
Jouni Malinen
534525ff05 P2P: Skip extra remain-on-channel if oper channel matches
There is no need to separately move to the correct channel
for transmitting an Action frame that is using the group
interface (i.e., source address is P2P Interface Address).
This removes extra latency from P2P Action frame operations
within a P2P group.
2010-11-02 19:35:40 +02:00
Jouni Malinen
b7412dabd9 P2P: Fix random channel selection to use os_get_random
This could have been using an uninitialized variable instead of
purposefully random value in picking up the channel. There is not
much of a difference for the use case here, but anyway, we may
as well do what was initially planned here and.
2010-10-31 12:27:37 +02:00
Jouni Malinen
79222cfa61 P2P: Reorder code to avoid memory leak on error path 2010-10-31 12:24:21 +02:00
Jouni Malinen
d394a22f30 P2P: Add NULL pointer validation for ssid for group started event
It looks likely that ssid is not NULL here, but better keep this
consistent with other uses of ssid pointer in this function.
2010-10-31 12:12:07 +02:00
Jouni Malinen
58e54293db P2P: Fix removal_reason setting to use correct pointer
The previous version triggered a NULL pointer dereference on
P2P_GROUP_REMOVE * command.
2010-10-27 11:47:41 +03:00
Jouni Malinen
c973f3868a P2P: Remove P2P group on driver resource becoming unavailable
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.

When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
2010-10-25 19:16:11 +03:00
Jouni Malinen
3071e18109 P2P: Add mechanism for timing out idle groups
A new configuration parameter, p2p_group_idle, can now be used to set
idle timeout value for P2P groups in seconds (0 = no timeout). If set,
this values is used to remove P2P group (both GO and P2P client)
interfaces after the group has been idle (no clients/GO seen) for the
configuration duration.

The P2P-GROUP-REMOVED event is now indicating the reason for group
removal when known. For example:
P2P-GROUP-REMOVED wlan0 GO reason=REQUESTED
P2P-GROUP-REMOVED wlan1 client reason=IDLE
2010-10-25 18:24:15 +03:00
Jouni Malinen
3f4ce13fde P2P: Track non-P2P members in the group and set Group Limit bit
The P2P group component is now tracking of associated stations
in the group and the Group Limit bit in the Group Capabilities
is updated based on whether there is room for new clients in
the group.
2010-10-19 18:10:28 +03:00
Jouni Malinen
de979d8fc7 Fix max_stations to apply to associated STAs, not P2P peers
This driver capability limit was supposed to indicate limit on
how many stations can associate with us in the AP mode, not how
many P2P peers are stored in the peer table.
2010-10-19 17:17:04 +03:00
Jouni Malinen
59eba7a2b3 P2P: Add p2p_cancel command for cancelling ongoing group formation 2010-10-19 15:53:28 +03:00
Jouni Malinen
93b7ddd032 P2P: Skip GO Neg Conf ack failure workaround of send failures
The workaround to ignore no ctrl::ack received for GO Negotiation
Confirmation frame was only supposed to be used when the frame was
actually transmitted and just the ack was not received. However, due
to the way the driver failure on transmitting the frame were reported,
this ended up getting applied for all failures in sending the GO
Negotiation Confirmation frame.

Improve this by providing a mechanism to indicate whether send_action
operations fail locally before the frame was actually transmitted or
because of not receiving ack frame after having transmitted the frame.
2010-10-19 12:47:33 +03:00
Jouni Malinen
d75e880696 P2P: Try to re-create group interface if pending one is not available
This is needed to work around cases where the pending interface gets
removed, e.g., due to failed GO Negotiation. In such case, we may still
accept new GO Negotiation to be completed, but the interface did not
get created without a separate p2p_connect command.

The current implementation is not ideal since the re-created interface
may, at least in theory, get incorrect interface addrees. Though, this
would likely require that the driver supported more than one P2P group
interface and that the previous one was already taken into use for
another group.
2010-10-18 17:00:50 +03:00
Jouni Malinen
b5c9da8db3 P2P: Add mechanism for updating P2P channel list based on driver events
This allows P2P channel list to be updated whenever the driver changes
its list of allowed channels, e.g., based on country code from scan
results.
2010-10-15 18:55:22 +03:00
Jouni Malinen
ac8d1011b7 P2P: Set channel list per channel instead of per band
This makes the channel list match with driver capabilities without
having to do workaround like disabling channels 12-14.
2010-10-15 18:51:37 +03:00
Jouni Malinen
4ae4650b4c P2P: Verify that forced channel is suitable for autonomous GO 2010-10-15 18:48:06 +03:00
Jouni Malinen
d054a4622c P2P: Reject multi-channel concurrent operations depending on driver
The driver wrapper can now indicate whether the driver supports
concurrent operations on multiple channels (e.g., infra STA connection
on 5 GHz channel 36 and P2P group on 2.4 GHz channel 1). If not,
P2P_CONNECT commands will be rejected if they would require
multi-channel concurrency.

The new failure codes for P2P_CONNECT:

FAIL-CHANNEL-UNAVAILABLE:
The requested/needed channel is not currently available (i.e., user has
an option of disconnecting another interface to make the channel
available).

FAIL-CHANNEL-UNSUPPORTED:
The request channel is not available for P2P.
2010-10-14 14:24:56 +03:00
Jouni Malinen
3b29972c09 P2P: Limit p2p_connect .. pbc join based on BSSID
Allow only the expected P2P Interface Address as the BSSID for
the AP to avoid selecting incorrect BSS should there be another
device that is advertising active PBC mode before the target
P2P GO does.
2010-10-12 16:56:17 +03:00
Johannes Berg
6cb22d2fd1 P2P: Fix remain-on-channel abort race
When the P2P state machine requests a remain- on-channel, there's a
potential race where it can then request a stop before the r-o-c has
actually started, in which case the stop will not be processed. Fix
that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2010-10-10 17:52:13 +03:00
Jouni Malinen
0e2e565a44 WPS 2.0: Provide (Re)Association Response WPS IE to driver
WPS 2.0 mandates the AP to include WPS IE in (Re)Association Response
if the matching (Re)Association Request included WPS IE. Provide the
needed WPS IE information to the driver_ops API for drivers that
process association frames internally.

Note: This modifies the driver_ops API by adding a new argument to
set_ap_wps_ie().
2010-09-22 10:46:44 -07:00
Sudhakar Swaminathan
0f66abd25b P2P: Add option for disabling intra BSS distribution
p2p_intra_bss configuration parameter can now be used to
disable/enable intra BSS distribution (bridging of frames between
the clients in a group).
2010-09-10 10:30:26 -07:00
Ardong Chen
2049af2bd5 P2P: Fix invitation_received callback to use NULL bssid (if not known)
Previously, the storage buffer for the Group BSSID was returned
regardless of whether it was included in the invitation or not.
2010-09-10 10:30:26 -07:00
Kuko Li
4c01083400 P2P: Do not process configuration changes on non-P2P interfaces 2010-09-10 10:30:26 -07:00
Jouni Malinen
b73bf0a74b P2P: Stop connection attempt on PBC session overlap
The overlap condition cannot disappear before group formation timeout
hits, so there is no point in continuing in this case and failure can
be indicated immediately.
2010-09-10 10:30:25 -07:00
Jouni Malinen
3094d4837a P2P: Use group formation timeout (but longer one) with join-a-group
This allows the pending group interface to be removed if we fail
to join a running group. A longer than 15 second timeout is needed
here since the GO may not have authorized our connection yet.
2010-09-10 10:30:25 -07:00
Jouni Malinen
ae3e342108 P2P: Add peer timeout into group formation 15 second timeout
This adds some more time for WPS provisioning step in case the peer
takes long time to start group interface operations.
2010-09-10 10:30:25 -07:00
Ardong Chen
c481048f7c P2P: Add frequency into group started ctrl_interface events 2010-09-10 10:30:25 -07:00
Jouni Malinen
e9a7ae41fa P2P: Use SSID from GO Negotiation to limit WPS provisioning step
In order to avoid picking incorrect SSID from old scan results, use
SSID from GO Negotiation to select the AP.
2010-09-09 07:17:23 -07:00
Jouni Malinen
743ef79914 P2P: Deinit GO group data before global P2P deinit
This avoids issues with using freed memory in p2p_group_deinit().
2010-09-09 07:17:23 -07:00
Jouni Malinen
f8d0131a11 P2P: Use operating frequency from peer table as backup for join
The scan operation before Provision Discovery Request may not include
the GO. However, we are likely to have the GO in our P2P peer table,
so use that information to figure out the operating channel if BSS
table entry is not available.
2010-09-09 07:17:23 -07:00
Jouni Malinen
a482883f63 P2P: Fix connect-to-running-group if Action TX status is delayed
The following operations (scan and associate) were not run if the
Provisioning Discovery Response is received before the TX Action
status.
2010-09-09 07:17:23 -07:00
Jouni Malinen
ab218b7c72 P2P: Add some more debug information for Action frame TX 2010-09-09 07:17:22 -07:00
Jouni Malinen
1cc3a29d49 P2P: Clear pending Action TX frame on p2p_stop_find and p2p_listen
This is needed to avoid issues with the previous TX command from
stopping long Listen state.
2010-09-09 07:17:22 -07:00
Jouni Malinen
10b9ac17cf P2P: For now, do not use channels 12-14 in P2P groups
This is needed to make sure we do not try to accidentally enable GO
in channels that may not be allowed. In addition, this may help with
some driver that do not like channel 14 even as a passive scan
channel.
2010-09-09 07:17:21 -07:00
Jouni Malinen
e1f1509bb0 P2P: Fix P2P IE generation for AssocReq when BSS info is not available
This code could segfault on NULL pointer dereference at least when
ap_scan=2 is used.
2010-09-09 07:17:21 -07:00
Jouni Malinen
c4ea4c5c90 P2P: Allow driver wrapper to indicate how many stations are supported
This can be used to limit the number of clients allowed to connect
to the group on the GO.
2010-09-09 07:17:21 -07:00
Jouni Malinen
3dfda83d9c P2P: Add Device Password ID to GO Neg Request RX event
This event indicates the Device Password ID that the peer tried
to use in GO Negotiation. For example:
P2P-GO-NEG-REQUEST 02:40:61:c2:f3:b7 dev_passwd_id=4
2010-09-09 07:17:20 -07:00
Jouni Malinen
4147a2cc64 P2P: Fix p2p_connect join with interface address
Need to fetch P2P Device Address from the peers table in case the
p2p_connect join command uses interface address.
2010-09-09 07:17:20 -07:00
Jouni Malinen
72044390f3 P2P: Add support for cross connection
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
2010-09-09 07:17:20 -07:00
Jouni Malinen
aefb53bd5d P2P: Disable periodic NoA when non-P2P STA is connected
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
2010-09-09 07:17:20 -07:00
Jouni Malinen
4c08c0bd57 P2P: Include P2P IE in (Re)AssocReq to infra AP if it uses P2P IE
While this is not strictly speaking required by the P2P specification
for a not-P2P Managed Device, this can provide useful information for
the P2P manager AP and may be needed to pass certification tests.
2010-09-09 07:17:20 -07:00
Jouni Malinen
d9d6a58c8f P2P: Fix invitation to active group to use correct operating channel
Invitation Request must use the current operating frequency of the
group, not the default operating channel.
2010-09-09 07:17:20 -07:00
Jouni Malinen
131cb37c2d P2P: Allow pre-authorization of invitation to apply to src addr
For client-invites-device case, the pre-authorization of an invitation
to running group will need to allow Invitation Request from specified
address, too. This is for testing uses only.
2010-09-09 07:17:19 -07:00
Jouni Malinen
6e6963ea86 P2P: Add test mode for SD to force fragmented response 2010-09-09 07:17:19 -07:00
Jouni Malinen
18708aadfc P2P: Initial support for SD fragmentation (GAS Comeback Request/Response) 2010-09-09 07:17:19 -07:00
Jouni Malinen
2a43101e48 P2P: Fix memory leak in SD service entries
Need to flush stored service entries when wpa_supplicant is being
terminated.
2010-09-09 07:17:19 -07:00
Jouni Malinen
bf608cad56 P2P: Rename SD info not available define to match with spec change 2010-09-09 07:17:19 -07:00
Jouni Malinen
706887fc28 P2P: Stop early when processing not-persistent invitation result 2010-09-09 07:17:19 -07:00
Jouni Malinen
2e062d5d74 P2P: Fix Group ID in Invitation Request from active GO
Need to get P2P Device Address, not the Interface Address.
2010-09-09 07:17:19 -07:00
Jouni Malinen
108def931e P2P: Add command for pre-authorizing an invitation to an active group
This is mainly designed for testing and allows p2p_connect join auth
to be used to accept a specific invitation to an active group that
may be received in the future.
2010-09-09 07:17:19 -07:00
Jouni Malinen
3c5126a41f P2P: Set Device Password ID in WPS M1/M2 per new rules
If the P2P client (WPS Enrollee) uses a PIN from the GO (Registrar),
Device Password ID in M1 & M2 is set to Registrar-specified.
2010-09-09 07:17:19 -07:00
Jouni Malinen
ef922c4a34 P2P: Run a scan before provision discovery in p2p_connect join
This is needed to make sure we have fresh BSS information for the GO.
2010-09-09 07:17:19 -07:00
Jouni Malinen
07a30a66c3 P2P: Do not schedule new remain-on-channel if waiting for drv event
The driver event for remain-on-channel may be delayed in a way that
allows management-frame-received event to be received before
wpa_supplicant knows that the driver is actually already on the
previously requested channel. We should not request a new
remain-on-channel to send a response to just a frame if we are waiting
for the driver to get to the same channel. Instead, just continue
waiting for the driver event.
2010-09-09 07:17:18 -07:00
Jouni Malinen
d6ae995057 P2P: Fix infinite loop on interface selection for Action frame TX
When the first wpa_supplicant interface is not the correct one for
transmitting an Action frame (e.g., P2P Presence Request frame
uses a group interface), the code got stuck in an infinite busy
loop. Fix the iteration to go through the interfaces properly.
2010-09-09 07:17:18 -07:00
Jouni Malinen
b22128efdc P2P: Add initial version of P2P Module 2010-09-09 07:17:17 -07:00