Commit graph

588 commits

Author SHA1 Message Date
Jouni Malinen
70e0cb33f2 P2P: Provide group SSID, if specified, to P2P Client join step
At least one of the wpas_p2p_connect() callers (NFC join case) already
had access to the Group SSID. Pass that information through
wpas_p2p_connect() to wpas_p2p_join() so that the join operation can
filter out incorrect groups more easily.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-30 19:08:51 +02:00
Jouni Malinen
438be60153 P2P: Do not accept any GO BSS entry if SSID is specified for join
Accept only a BSS entry matching the SSID when trying to find the
operating channel of a GO during join operation for which the SSID was
already specified. Previously, it could have been possible to pick an
incorrect BSS entry if the new GO was not found in the latest scan and
there was an older cached scan entry for the same BSSID.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-30 19:06:19 +02:00
Jouni Malinen
35510d530a P2P: Use join SSID in the skip-PD cases
It was already possible to limit join operation to accept only a
specific SSID. However, this constraint was not used when starting a P2P
Client interface as a WPS Enrollee without going through a Provision
Discovery exchange.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-30 19:04:43 +02:00
Jouni Malinen
8b8d4f4eb4 P2P: Do not accept any BSS entry for join if SSID is already known
Use wpa_bss_get() with the specific Group SSID instead of
wpa_bss_get_bssid_latest() if the SSID is already known. This makes the
P2P join operations more robust in case the frequency of the group was
not yet known and the same P2P Interface Address may have been used in
multiple group instances with an older group entry still present in the
cached scan results.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-30 19:02:33 +02:00
Jouni Malinen
b875276c4d P2P: Use group SSID, if known, for join operation even if no BSS entry
This allows the cases where a specific group SSID is known to filter out
groups on the P2P Client even if the specific BSS entry for the target
group is not yet available.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-30 19:00:56 +02:00
Jouni Malinen
aa256cb399 P2PS: Add group SSID, if known, to the P2PS-PROV-DONE event
The new optional group_ssid=<hexdump> argument in the P2PS-PROV-DONE
event can be used to help in identifying the exact group if there have
been multiple groups with the same P2P Interface Address in short period
of time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-30 18:59:03 +02:00
Jouni Malinen
662512e027 P2PS: Remove dead code
Commit f8a80e39b3 ('P2PS: Change
connection capability handling') added the identical P2PS_SETUP_CLIENT
check into two places within p2ps_group_capability(). However, only the
first one of these can be reached. In the second case, role can only
have values 0 or P2PS_SETUP_NEW and as such, the P2PS_SETUP_CLIENT case
is not possible. It looks like the first part of the commit is
sufficient, so remove the dead code added by the second part.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-24 19:16:15 +02:00
Ayala Beker
1b3dd69d93 P2P: Fix possible NULL pointer dereference
Fix wpas_p2p_invite() to call p2p_set_own_pref_freq_list() after the
NULL check, to avoid NULL pointer dereference if P2P initialization were
to have failed or P2P module getting deinitialized.

Signed-off-by: Ayala Beker <ayala.beker@intel.com>
2015-12-18 00:24:51 +02:00
Jouni Malinen
bf3214b593 P2P: Fix re-invoked client interface completion on data connection
This was already working for the case where a separate group interface
is used due to the recent commit
328f49acfe ('P2P: Complete group formation
on client data connection'). However, the case of no separate group
interface was used did not clear the interface state properly on data
connection. Fix this by setting the group formation information in
wpas_start_p2p_client().

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-04 23:11:10 +02:00
Jouni Malinen
63502c64e1 P2P: Fix P2P_CANCEL for p2p_in_invitation case
Commit f05cee9714 ('P2P: Clear
p2p_in_invitation on cancel') added a wpas_p2p_cancel() case to call
wpas_p2p_group_formation_failed() if wpa_s->p2p_in_invitation is set.
This is done in a loop going through wpa_s->next pointers. However, the
call here can result in removing the interface and freeing wpa_s. The
following attempt to read wpa_s->next is from freed memory and that can
result in process termination when using a separate P2P group interface
and issuing P2P_CANCEL on a group that was started through re-invocation
of a persistent group.

The recent commit 328f49acfe ('P2P:
Complete group formation on client data connection') "fixed" this by
accident since wpa_s->p2p_in_invitation gets cleared in the sequence
that could hit this issue and this results in P2P_CANCEL getting
rejected. However, the real bug here is in the loop that continues after
possible wpa_s instance deletion. Fix that by breaking out of the loop.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-04 22:49:59 +02:00
Jouni Malinen
328f49acfe P2P: Complete group formation on client data connection
This was already the case in the GO role where the first client
connection is waited before marking
wpa_s->p2p_go_group_formation_completed = 1 and clearing
wpa_s->global->p2p_group_formation. However, in the P2P Client role,
that was done already at the completion of the WPS exchange. This can be
problematic since group formation timeout may still try to clear the
group and with wpa_s->global->p2p_group_formation == NULL, the correct
group interface may not be found.

Fix this by postponing clearing of wpa_s->global->p2p_group_formation on
the P2P Client side until the data connection has been completed and
group is declared started.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-30 21:35:16 +02:00
Jouni Malinen
dd895e9964 P2P: Make p2p_go_configured() more robust against unexpected calls
A hwsim test sequence was able to hit a SIGSEGV in
p2p_go_save_group_common_freqs() called by p2p_go_configured() callback
in a case where a non-P2P AP mode operation is started in wpa_supplicant
(wpas_ap_wep test case). This callback should not have happened for
non-P2P case and the debug logs did not make it clear how this could
happen. In addition, it is unclear how this could be reproduced.

To avoid this type of issues, clear the wpa_s->ap_configured_cb pointer
as soon as the first call to the function happens. In addition, verify
that wpa_s->go_params is available before processing the GO configured
callback.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-11-30 01:25:24 +02:00
Ahmad Kholaif
c27f4c9006 P2P: Add support for VHT 80+80 MHz and 160 MHz
The new max_oper_chwidth and freq2 arguments to P2P_CONNECT, P2P_INVITE,
and P2P_GROUP_ADD control interface commands can be used to request
larger VHT operating channel bandwidth to be used than the previously
used maximum 80 MHz.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 19:01:20 +02:00
Ahmad Kholaif
bee5d8e067 nl80211: Add VHT 160 MHz channel flags
This extends the previous design that covered only the VHT 80 MHz cases
for VHT channel flags. New functions are introduced to allow 160 MHz
bandwidth cases to determine the center channel and check availability
of a 160 MHz channel.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 19:01:14 +02:00
Ahmad Kholaif
5e1da9c8fd P2P: Define operating classes for VHT 80+80 and 160
This adds definitions for the global operating classes 129 and 130 for
VHT 80+80 MHz and 160 MHz use cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-25 19:01:10 +02:00
Ilan Peer
ed7820b484 P2P: Add a testing option to force P2P GO CSA
Add a testing option to force a P2P GO CSA on successful
invitation to join an active P2P GO.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-11-22 21:49:19 +02:00
Ilan Peer
6cbbae2cf8 P2P: Set p2p_go_wait_client in invitation_result() cb
When an invitation to join an existing group is accepted by the
peer device, set p2p_go_wait_client to the current time so
that wpas_p2p_in_progress() would return != 0, thus preventing
P2P CSA, scanning etc., that would interfere with the peer
device connection.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-11-22 21:46:43 +02:00
Avraham Stern
2c51c0bd83 P2P: Clear send action work without waiting on find/stop/listen
When clearing pending TX action to start a new P2P operation like
P2P_FIND or P2P_LISTEN, wpas_p2p_action_tx_clear() was used to clear
the send action work. However, in cases where the action work has wait
time, it is not cleared immediately but only after the wait time ends.
This may cause delay in starting the P2P operation.

Fix that by always clearing the send action work immediately on these
P2P commands that result in immediate P2P state change and practically
stopping a previous operation, if one was pending.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-11-21 18:53:22 +02:00
Jouni Malinen
e699a7a9b3 P2P: Add more debug prints for Action frame TX clearing steps
This makes it easier to analyze debug logs for issues related to
multiple pending Action TX frames.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-10-15 21:20:22 +03:00
Max Stepanov
cd571e14dd P2PS: Fix persistent group reporting in wpas_p2ps_prov_complete()
When one peer doesn't include a persistent group info in PD Request
the other peer shouldn't report a persistent group usage with this
peer even if such a persistent group exists locally. This condition
could be violated in the previous implementation.

In case a local persistent group exists and the
wpas_p2ps_prov_complete() function is called with persist_ssid parameter
set to NULL, wpa_supplicant reported P2PS-PROV-DONE with persist=<idx>
instead of conncap=<role> parameter.

This happened because the wpas_p2p_get_persistent() function was called
without verification whether the persist_ssid was set to NULL. In this
case the wpas_p2p_get_persistent() returns the first existing persistent
group matching the P2P Device Address without verifying the group's
SSID. After that the group ID is used as persist=<idx> parameter of
P2PS-PROV-DONE event.

Fix the issue by adding persist_ssid and persist_ssid_size verification
as a condition for the wpas_p2p_get_persistent() call.

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
2015-10-11 21:42:03 +03:00
Ilan Peer
8bb8e6edb8 P2PS: Indicate the chosen operating frequency
On successful P2P PD, report the chosen frequency in case the local
device is going to be the P2P GO, so in can later be used to instantiate
the new P2P GO, etc.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-10-11 21:42:03 +03:00
Ilan Peer
ebd32943cb P2PS: Add channel policy to PD Request
Add operating channel selection and channel list processing similar to
that done when building GO Negotiation Request, i.e., consider the
currently used channels, configured channels, etc.

P2PS introduces a flow where a responder needs to provide channel data
without being previously aware of the current constraints, i.e., the
channels currently in use by other interfaces. To handle this, extend
the get_group_capability() callback to also handle channel selection
aspects of group capabilities.

In case there is an active P2P GO that is going to be used for the P2PS
PD, force its current operating frequency in the PD attributes.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-10-11 21:42:03 +03:00
Ilan Peer
f8a80e39b3 P2PS: Change connection capability handling
Change the connection capability handling so that in case there are no
active roles, the peer has an active GO, and the advertisement supports
operation as a client, the returned connection capability is set to
client.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-10-07 17:07:21 +03:00
Ilan Peer
ab804bcb6f P2PS: Re-factor p2ps_group_capability()
The code was iterating all the interfaces, and for each interface
iterated all the network blocks to count active P2P GO and P2P Client
interfaces.

Change the code to reuse wpas_p2p_get_go_group() to get a P2P GO
interface and add wpas_p2p_get_cli_group() and use it to find a
P2P Client interface, and use these objects when evaluating the
group capability.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-10-07 17:07:21 +03:00
Ilan Peer
8d5e73290f P2PS: Re-factor wpas_p2p_get_go_group() and wpas_p2p_group_go_ssid()
Re-factor wpas_p2p_get_go_group() to:

1. Skip the dedicated P2P Device management interface if it is used.
2. Instead of iterating all the interface configured networks,
   only access the current_ssid pointer to check if the current
   interface is acting as a persistent P2P GO.

To avoid code duplication, also re-factor wpas_p2p_group_go_ssid()
to call wpas_p2p_get_go_group().

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-10-07 17:07:21 +03:00
Luciano Coelho
7d82170aba Set channel and operating class in hostapd_fill_csa_settings()
The CSA channel and operating class values need to be set for all types
of channel switch (i.e., either if it's triggered by the control
interfaces or due to the GO-follows-STA flow). To do so, move the code
that sets them from the GO-follows-STA flow to the more generic
hostapd_fill_csa_settings() function.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
2015-10-03 21:26:23 +03:00
Andrei Otcheretianski
98b0508121 P2P: Implement P2P_GO_FREQ_MOVE_SCM_ECSA policy
Add new GO frequency move policy. The P2P_GO_FREQ_MOVE_SCM_ECSA prefers
SCM if all the clients advertise eCSA support and the candidate
frequency is one of the group common frequencies.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-10-03 20:30:40 +03:00
Andrei Otcheretianski
3bafb0d842 P2P: Trigger channel selection correctly during CSA
Do not consider moving GOs to a new channel if one of them is in the
middle of CSA. In addition, call wpas_p2p_update_channel_list() after
EVENT_CH_SWITCH is handled.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-10-03 20:22:09 +03:00
Ilan Peer
23dcb302eb P2P: Relax wpas_p2p_init_go_params() for P2P GO CSA
wpas_p2p_move_go_csa() uses wpas_p2p_init_p2p_params() to select the
frequency to move to. However, it is possible that all the channels are
already used, so the selection of a new frequency would fail, although
the frequency used by the P2P GO should not be considered as used if it
is the only one using it.

To overcome this, allow the frequency selection to continue even if all
the frequencies are in use, but the frequency used by the P2P GO is not
used by any station interface.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-10-03 20:16:51 +03:00
Andrei Otcheretianski
73afc20d40 P2P: Implement wpas_p2p_move_go_csa()
Use channel switch mechanism to move a P2P GO to a new channel,
when required. In order to be able to reconfigure the GO channel,
split wpa_supplicant_conf_ap() function, so the frequency
configuration part can be reused to find additional CSA settings.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-10-03 20:10:37 +03:00
Maneesh Jain
be5ab8d4ab D-Bus: Add InvitationReceived Signal
This is equivalent to the P2P_EVENT_INVITATION_RECEIVED signal on the
control interface. It can be used to sent the Invitation Received signal
to applications written using D-Bus.

Signed-off-by: Maneesh Jain <maneesh.jain@samsung.com>
2015-09-27 15:55:11 +03:00
Nishant Chaprana
2a95fac944 P2P: Add D-Bus signal GroupFormationFailure
This is similar to the control interface event
P2P-GROUP-FORMATION-FAILURE.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2015-09-05 23:01:20 +03:00
Jouni Malinen
941cd3ec70 P2P: Request fresh scan results after GO Negotiation
The P2P group is not yet operating when going through GO Negotiation
exchange. Previously, an old cached scan result could be used to skip
the scan immediately after the GO Negotiation. While this is quite
unlikely to happen in practice, we can easily force a scan here now with
the generic scan_min_time mechanism. Do that to avoid any corner cases
that a previous instance of the group could have if found in cached scan
results.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-22 00:22:12 +03:00
Jouni Malinen
dfaf11d648 P2P: Require fresh scan results for persistent group re-invocation
The P2P group is not yet operating when going through invitation
exchange for re-invocation. Previously, an old cached scan result could
be used to skip the scan immediately after the invitation exchange.
While this may result in the fastest possible connection, it does have
some issues with cases where the GO takes some time to start up. It
would also be at least theoretically possible for some of the BSS
parameters to be different, so having a fresh scan result from the new
GO instance may be desired in any case.

Add a mechanism to skip scan results that have been last updated before
a specific point in time and as the first user for this mechanism,
require chan results to be more recent than the invitation message
exchange for the P2P Client role in persistent group re-invocation case.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-22 00:22:12 +03:00
Andrei Otcheretianski
d494ca0be4 P2PS: Consider WPS P2PS method when joining a group
If P2PS PD concludes to use default P2PS method wpas_p2p_scan_res_join()
ignores this value and tries to perform a redundant legacy PD.
Fix this by considering WPS_P2PS method too.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-08-14 23:56:12 +03:00
Ahmad Kholaif
fbcddaed9a P2P: Support driver preferred freq list for invitation case
When using P2P invitation to re-invoke a persistent P2P group without
specifying the operating channel, query the driver for the preferred
frequency list, and use it to select the operating channel of the group.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-11 19:04:45 +03:00
Ahmad Kholaif
8e84921efe P2P: Support driver preferred freq list for Autonomous GO case
When starting an autonomous GO without specifying the operating channel,
query the driver for the preferred frequency list, and use it to select
the operating channel of the GO (if supported).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-10 21:27:42 +03:00
Andrei Otcheretianski
b9da88d6c1 P2PS: Authorize any peer for P2PS method if interface address not known
When P2PS PD with default P2PS method is done, the peer that becomes GO
should authorize the client. However, P2PS specification doesn't require
the client to include its intended interface address in PD
Request/Response. As a result, the P2P Client's interface address may not
be known and any address may need to be authorized.

Previously, client's P2P Device Address was used for authorization,
which is not correct when a dedicated interface is used for P2P Client.
This is not resulting in a connection failure, however it causes a
significant delay (until WPS_PIN_TIME_IGNORE_SEL_REG elapses). Fix this
by authorizing the intended interface address, if known; or any address,
if not known.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-08-06 20:45:15 +03:00
Jouni Malinen
2a098e3668 P2PS: Clean up intended interface address passing to p2ps_prov_complete
Use NULL to indicate if the address is not available instead of fixed
00:00:00:00:00:00. wpas_p2ps_prov_complete() already had code for
converting NULL to that all zeros address for event messages.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-08-06 20:45:15 +03:00
Ilan Peer
3a8f008a24 P2P: Do not perform P2P GO CS in some cases
A P2P GO channel switch should not be triggered in all cases that
require channel list update. Specifically, a P2P GO CS should not
be triggered in case that the P2P GO state changed or in case that
that the P2P GO has just completed a CS.

To fix this, add reason code to wpas_p2p_channel_list_update() and
trigger CS flow only for the relevant cases.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-08-04 18:34:47 +03:00
Ilan Peer
dae4c82c95 P2P: Disallow GO CS immediately after GO Negotiation or invitation
A newly created GO might move to another channel before the client was
able to connect to it. This creates a situation where the client
searches the GO on the channel agreed upon during GO Negotiation or
invitation signaling, while the GO is on another channel. This in turn
might lead to delayed connection or connection failure and group
removal.

Fix this by disallowing a GO CS as long as there is some activity that
should delay the switch. If a GO move is not allowed, set a timeout to
re-attempt the move.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-08-04 16:14:30 +03:00
Ilan Peer
c2675c87c3 P2P: Consider channel optimizations for additional cases
Re-factor the code, so channel optimizations would be also triggered
upon the following changes: channel updates from the kernel,
disallow_freq interface, etc.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-08-04 16:09:21 +03:00
Ilan Peer
b130812100 P2P: Modify wpas_p2p_init_go_params()
Not all paths in wpas_p2p_init_go_params() verified that the candidate
frequency can be used for GO purposes. Fix this, and in addition
re-factor the code to put better emphasis on the frequency selection
priorities.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-08-04 00:38:54 +03:00
Ilan Peer
e280110d17 P2P: Move a GO to a frequency that is also supported by the client
A P2P GO interface that was instantiated after a GO Negotiation or
Invitation holds the intersection of frequencies between the GO and the
client. In case the GO is going to move to another frequency, allow it
to move only to a frequency that is also supported by the client.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-08-04 00:27:13 +03:00
Ilan Peer
5e1f480500 P2P: Add a function to compute the group common freqs
Add a function to compute the group common frequencies, and
use it to update the group_common_frequencies as part of the
channel switch flows.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-08-04 00:18:51 +03:00
Ilan Peer
1a471ff081 P2P: Move a GO from its operating frequency
Upon any change in the currently used channels evaluate if a GO should
move to a different operating frequency, where the possible scenarios:

1. The frequency that the GO is currently using is no longer valid,
   due to regulatory reasons, and thus the GO must be moved to some
   other frequency.
2. Due to Multi Concurrent Channel (MCC) policy considerations, it would
   be preferable, based on configuration settings, to prefer Same
   Channel Mode (SCM) over concurrent operation in multiple channels.
   The supported policies:

   - prefer SCM: prefer moving the GO to a frequency used by some other
     interface.
   - prefer SCM if Peer supports: prefer moving the GO to a frequency
     used by some other station interface iff the other station
     interface is using a frequency that is common between the local and
     the peer device (based on the GO Negotiation/Invitation signaling).
   - Stay on the current frequency.

Currently, the GO transition to another frequency is handled by a
complete tear down and re-setup of the GO. Still need to add CSA flow to
the considerations.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-08-04 00:14:41 +03:00
Michael Olbrich
be11a59486 P2P: Cancel group formation when deleting a group during group formation
Otherwise P2P remains in provisioning state and continues to skip
extended listening forever.

Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
2015-08-02 21:37:09 +03:00
Jouni Malinen
9f59fe8dc8 P2P: Do not clear wpa_s->go_dev_addr before group removal
This variable is needed to figure out whether a wpa_supplicant interface
is for a P2P group that is (or was) connected to a specific GO. The
previous implementation was able to find such a case only when there was
an association with the GO. However, this may be needed even if there is
a temporary disconnection from the GO. Keep the GO device address
information over such temporary disconnections and only remove it on
group termination. This fixes an issue with D-Bus Peer PropertiesChanged
signals for the Groups property in case a P2P group gets removed due to
group idle timeout instead of explicit group termination command (local
request) or GO notification.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-08-02 21:37:09 +03:00
Ahmad Kholaif
fc71f7d99d P2P: Expose driver preferred frequency list fetch to P2P
This adds a callback function that can be used from the P2P module to
request the current preferred list of operating channels from the
driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-30 22:13:48 +03:00
Ahmad Kholaif
370017d968 P2P: Use preferred frequency list from the local driver
If the driver supports the preferred frequency list extension, use this
information from the driver when no explicitly configured preference
list (p2p_pref_chan) is present for P2P operating channel selection.
This commit adds this for GO Negotiation and Invitation use cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-30 22:13:48 +03:00
Ahmad Kholaif
7c813acf9c P2P: Inform driver of the operating channel following group formation
Upon GO Negotiation completion, if the remote peer becomes GO, send a
hint event over QCA vendor specific interface to inform the driver of
the likely operating channel of the P2P GO.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-29 19:10:16 +03:00
Max Stepanov
88f3d7c980 P2PS: Add feature capability to PD events
Report the feature capability on P2PS-PROV-START and P2PS-PROV-DONE
ctrl-iface events. A feature capability value is specified as
'feature_cap=<hex>' event parameter, where <val> is a hexadecimal
string of feature capability bytes in a PD Response frame.

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-07-27 00:47:19 +03:00
Andrei Otcheretianski
5cc6ec0f68 P2PS: Set intended interface address correctly for new group
If a device may be an explicit GO, it adds the GO details in the PD
Request. First, we try to reuse an active GO. If it is not present, we
try to reuse a non-active persistent group. In the latter case, if a
dedicated P2P interface is needed, the intended address should be that
of the pending interface. However, the wpas_get_go_info() provided the
ssid->bssid address, which is the address of the P2P device. This might
result in an incorrect intended interface attribute in the PD Request in
case a separate group interface is used.

Fix this by setting group_iface variable to true only if a dedicated
interface should be used and set the attribute accordingly.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-07-07 20:57:07 +03:00
Andrei Otcheretianski
1f14e2bf92 P2PS: Add PD Response validation
Validate the PD Response frame contents more thoroughly when it is used
for P2PS.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-07-07 20:52:38 +03:00
Andrei Otcheretianski
1f1a08b4cc P2PS: Add intended iface address during PD for persistent group
When persistent group is used and the peer is GO in this group,
intended interface attribute should be added to PD request/response.
Not doing so violates the spec.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-07-07 20:41:19 +03:00
Andrei Otcheretianski
23bb9828a3 P2PS: Fix P2PS-PROV-DONE event on GO
If after P2PS PD the device should become a GO it sends P2PS-PROV-DONE
event which contains the GO interface name. If the GO isn't running yet
the device may use pending interface name. However, when the GO is
started, pending interface name will be removed.

Fix the GO interface name in P2PS-PROV-DONE event by copying the
interface name instead of saving the pointer.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-07-07 20:34:14 +03:00
Andrei Otcheretianski
a698d6c85f P2PS: Use wpas_p2p_create_iface() to check if dedicated iface is needed
Call wpas_p2p_create_iface() instead of just checking p2p_no_group_iface
config value. Not doing so, resulted in an incorrect behavior when the
driver sets WPA_DRIVER_FLAGS_DEDICATED_P2P_DEVICE flag.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-07-07 20:30:12 +03:00
Ilan Peer
f43c1ae798 P2P: Handle P2P Device dedicated interface parent removal
In case of a network interface removal, check if the interface
was also the parent interface of the P2P Device dedicated interface.
If this is the case, then stop the P2P Device functionality, and
remove the P2P Device dedicated interface.

In case that the interface is added again and P2P Device
functionality can be enabled again, add a new P2P Device dedicated
interface and allow further P2P Device functionality.

In case that the P2P Device dedicated interface is re-created, the
original P2P Device configuration file is needed, so store it in
the global params (instead in the wpa_interface configuration).

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-06-19 16:22:26 +03:00
Eliad Peller
e4a80d89bd P2P: Fix secondary channel selection for HT40
wpas_p2p_get_ht40_mode() used blacklist approach (bw != BW20) to find
the relevant op_class, but didn't take into account other non-BW40
cases, like BW80, that had been added to the bw enum after the initial
implementation. Fix this by looking for the specific BW40 bw cases.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-06-19 15:50:40 +03:00
Ilan Peer
de7b02fd18 P2P: Use the P2P Device interface in wpas_p2p_fallback_to_go_neg()
Previously the wpa_s->parent interface was used, which is not
necessarily the P2P Device management interface.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-06-19 11:07:50 +03:00
Jouni Malinen
d95c5994c8 P2P: Fix group interface addition failure properly for concurrent case
It was possible for a P2P group formation failure to result in a
concurrent station mode operation getting disconnected in the specific
error case where group interface addition fails after a successful GO
Negotiation. Fix this by skipping the wpas_p2p_group_delete() call in
this specific case since the group interface does not exists anymore at
the point wpas_group_formation_completed() gets called.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-15 23:43:00 +03:00
Andrei Otcheretianski
0799b3f899 P2P: Specify frequency when sending Probe Response frame
If the RX frequency of the Probe Request frame is known, specify it when
sending the Probe Response frame. This is needed when the Probe Request
frame is received on another virtual interface, for example, when a GO
or P2PS client are discoverable on the group operating channel.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Max Stepanov
07c1e987d5 P2PS: Enable Probe Request frame processing by P2P Client
1. Add global p2p_cli_probe property to enable/disable Probe Request
frame RX reporting for connected P2P Clients. The property can be set to
0 - disable or 1 - enable. The default value is 0.

2. Enable Probe Request frame RX reporting for P2P Client on
WPA_COMPLETED state if p2p_cli_probe property is set to 1. Disable it
when an interface state is changing to any other state.

3. Don't cancel Probe Request frame RX reporting on wpa_stop_listen for
a connected P2P Client handling Probe Request frames.

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Max Stepanov
734ddf6125 P2P: Add rx_freq parameter to Probe Request frame handler
In some cases, Probe Request frames can be received by a peer not only
on a listen channel. In this case an additional rx_freq parameter
explitly contains a Probe Request frame RX frequency. In case rx_freq is
set to 0, a Probe Request frame RX channel is assumed to be our own
listen channel (p2p->cfg->channel).

Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Jouni Malinen
e6012e839d P2P: Update target GO Device Address from BSS entry during join
It is possible for P2P_CONNECT-join command to be issued on a GO's P2P
Interface Address before the P2P peer entry is available to map this
into the GO's P2P Device Address. This could result in the join
operation failing to continue after receiving PD Response due to the
address mismatch (source address = P2P Device Address while only the P2P
Interface Address is known). Fix this by updating the pending join P2P
Device Address based on the BSS entry, if needed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-06-14 23:16:55 +03:00
Amr BEN ABDESSALEM
0c9fb14ec4 P2P: Add Operating class 125 for P2P supported channels
Add operating class 125 (channels 149..169) to the list of P2P supported
channels. This allows the 5 GHz channels 161 and 169 to be used for P2P
GO when those channels are allowed for AP mode in the current regulatory
domain.

Signed-off-by: Amr BEN ABDESSALEM <amrx.ben.abdessalem@intel.com>
2015-06-12 20:39:49 +03:00
MAYANK HAARIT
aa2b12562b P2P: Add GO Intent of connecting device in GO Negotiation Request event
Add GO Intent information of connecting device in GO Negotiation Request
event which will help applications to decide its own GO intent value in
advance and can avoid failure cases when both devices use GO Intent 15
depending on application requirement.

Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
2015-06-06 18:16:39 +03:00
Krishna Vamsi
ccad05a95c P2P: Restart group formation timer upon receiving new Inv Req
A new Invitation Request might be received on a just started persistent
group if the previous Invitation Response sent isn't received at the
peer (GO of the persistent group). When the peer sends an Invitation
Request again, treat it as start of group formation and restart the
group formation timer at this point of time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-05-29 13:30:26 +03:00
Ilan Peer
b4342ca4d8 P2P: Use p2p_init_wpa_s for P2P command redirection over D-Bus
D-Bus used the p2p_dev member in struct wpa_supplicant to track the
interface used for P2P Device operations. However, this is not needed as
the interface used for P2P Device operations is stored in struct
wpa_global->p2p_init_wpa_s.

Replace all the redirections to wpa_s->p2p_dev with redirections to
wpa_s->global->p2p_init_wpa_s and removed this member as it is no
longer needed.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-05-25 18:31:09 +03:00
Ilan Peer
b740401f18 P2P: Fix wpas_remove_persistent_peer() to use P2P mgmt interface
The function used wpa_s->parent->conf to iterate the P2P networks and
update the configuration file. However, wpa_s->parent is not
necessarily the interface used to manage the P2P Device operations.

Fix this by accessing the configuration file of the interface
initialized to manage the P2P Device operations.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-05-25 18:31:09 +03:00
Ilan Peer
1e0a02942b P2P: Fix wpas_p2p_add_persistent_group_client() to use P2P mgmt interface
The function used wpa_s->parent->conf to iterate the P2P networks and
update the configuration file. However, wpa_s->parent is not
necessarily the interface used to manage the P2P Device operations.

Fix this by accessing the configuration file of the interface initialized
to managed the P2P Device operations.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-05-25 18:31:09 +03:00
Ilan Peer
86b91c89af P2P: Fix wpas_p2p_set_own_freq_preference() to use P2P mgmt interface
wpas_p2p_set_own_freq_preference() accessed wpa_s->parent->conf to test
if p2p_ignore_shared_freq is set, but wpa_s->parent is not necessarily
the interface used to manage the P2P Device operations.

Fix this by accessing the configuration file of the interface
initialized to manage the P2P Device operations.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-05-25 18:31:09 +03:00
Ben Rosenfeld
43677494fb P2P: Use the P2P Device management interface in wpas_p2p_remove_client()
As wpas_p2p_remove_client() is not necessarily called from the interface
used to manage the P2P Device operations, when removing a client, use
the P2P management interface to iterate over the saved networks and
remove the relevant entries form the P2P GO network blocks.

Signed-off-by: Ben Rosenfeld <ben.rosenfeld@intel.com>
2015-05-25 18:31:09 +03:00
Nishant Chaprana
7b642dc80b P2P: Add D-Bus FindStopped to notify P2P-FIND-STOPPED event
Add D-Bus notification mechanism of P2P-FIND-STOPPED event on
fi.w1.wpa_supplicant1.Interface.P2PDevice interface.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2015-05-25 18:31:09 +03:00
Sunil Dutt
d63f1419b5 P2P: Advertize cross connection to WLAN AP on a non-P2P interface
Commit 1c2aa04c96 ('P2P: Do not add P2P
IEs on P2P disabled interface') removed the P2P IEs from association on
non-P2P interface. However, an AP functioning as a P2P manager needs the
cross connection capability of the station (P2P Device). This needs to
be done to meet the P2P specification requirements even if the station
interface has p2p_disabled=1 in case P2P in general is enabled.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-05-25 12:44:53 +03:00
Jouni Malinen
5678a2d89b P2P: Allow wpa_supplicant to start if social channels are not supported
It was possible for an nl80211-based driver to be determined to support
P2P even when the radio supports only the 5 GHz band. This resulted in
P2P initialization failing due to not being able to pick a social
channel and wpa_supplicant not starting. Fix this by not enabling P2P,
but still allowing wpa_supplicant initialization to complete.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-04-26 13:59:06 +03:00
Mikael Kanstrup
8b423edbd3 Declare all read only data structures as const
By analysing objdump output some read only structures were found in
.data section. To help compiler further optimize code declare these
as const.

Signed-off-by: Mikael Kanstrup <mikael.kanstrup@sonymobile.com>
2015-04-25 17:33:06 +03:00
Avraham Stern
989e784601 P2P: Optimize scan frequencies list when re-joining a persistent group
When starting a P2P client to re-join a persistent group
(P2P_GROUP_ADD persistent=<id>), it is possible that the P2P GO was
already found in previous scans. Try to get the P2P GO operating
frequency from the scan results list so wpa_supplicant will initially
scan only the P2P GO known operating frequency.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2015-03-29 20:52:09 +03:00
Jouni Malinen
0f89328575 P2P: Move upper layer SD interaction into a separate file
wpa_supplicant/p2p_supplicant.c has reached almost 10000 lines in length
and was getting a bit inconvenient to edit, so start splitting it into
separate files.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-15 20:25:48 +02:00
Ahmad Kholaif
d7f1aa8fd7 DFS offload: P2P changes for autonomous GO
Add P2P changes to allow bringing up P2P autonomous GO on a DFS channel
if DFS functionality is offloaded to the driver.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-05 17:24:13 +02:00
Krishna Vamsi
95d7b863ec P2P: Consider 5 GHz channels also for auto GO
When there is no channel preference mentioned by user, auto GO
can be started on any of the 5 GHz channels supported for P2P.
Consider operating classes 115 and 124 which do not require DFS.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-03-02 17:01:15 +02:00
Jouni Malinen
1772d348ea P2P: Fix interface deinit for failed group interface initialization
wpa_supplicant_deinit_iface() ends up removing all P2P groups if the
removed interface is the parent interface. This is correct behavior in
general, but this resulted in issues in the new group interface
initialization error path since wpa_s->parent was not assigned before
hitting this check. Fix this by assigning wpa_s->parent as part of
wpa_supplicant_add_iface().

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-01 22:36:53 +02:00
Daisuke Niwa
fa9f381f20 P2P: Allow a specific channel to be specified in P2P_FIND
The optional freq=<MHz> can now be used with the P2P_FIND command to
specify a single channel to scan during the first round of P2P search.
For example, this can be used to replace the full initial scan with a
single channel scan of a known operation channel.

Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
2015-02-28 21:52:56 +02:00
Daichi Ueura
eb78a8d5e3 P2P: Restore P2P_SCAN_SPECIFIC
This reverts commit 3df2f4fe99 ('P2P:
Remove unused P2P_SCAN_SPECIFIC') with a modification to fit the current
code base.

Signed-off-by: Daichi Ueura <daichi.ueura@sonymobile.com>
2015-02-28 21:41:38 +02:00
Eliad Peller
0b8bcaa50f P2P: Allow configuring CTWindow when working as GO
Read p2p_go_ctwindow (0-127 TUs) from the config file, and pass it to
the driver on GO start.

Use p2p_go_ctwindow=0 (no CTWindow) by default.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
2015-02-21 16:07:53 +02:00
Jouni Malinen
6b00512164 P2P: Add event messages for P2P_CONNECT-fallback-to-GO-Neg
This makes it easier for upper layer programs to follow progress of
P2P_CONNECT-auto operation.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:48 +02:00
Jouni Malinen
b0e669beeb P2P: Fix P2P_CONNECT-auto fallback to GO Neg with group interface
If a separate P2P group interface was used, P2P_CONNECT-auto fallback to
GO Negotiation could result in use of freed memory and segmentation
fault. This happened in cases where the peer GO was found in some old
scans, but not in the first scan triggered by the P2P_CONNECT-auto
command ("P2P: Peer was found running GO in older scan -> try to join
the group" shows up in the debug log). In addition, the GO would still
need to reply to PD Request to allow this code path to be triggered.

When five scans for the GO were completed in this sequence, the P2P
group interface was removed as part of falling back to GO Negotiation.
However, that ended up dereferencing the freed wpa_s instance at the end
of scan event processing. Fix this by reordering code a bit and breaking
out from EVENT_SCAN_RESULTS processing if the interface could have been
removed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-08 13:35:14 +02:00
Jouni Malinen
abe96d0605 P2P: Clean up Listen channel optimization debug prints
Do not claim to change the Listen channel in a debug message when
previously configured channel prevents this. In addition, fix a typo in
another related debug print.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 16:13:35 +02:00
Krishna Vamsi
93eca6155b P2PS: Do not remove pending interface on p2p_stop_find
The pending interface created during provision discovery should
not be removed on stopping p2p_find. This pending interface has
to be used after completing GO negotiation. Earlier the pending
interface is created just before GO negotiation so there was no
problem.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
306aaf49f8 P2PS: Start WPS registrar upon GO formation
If P2PS config method is used for provisioning, upon forming a new GO,
start WPS registrar for the provisioned peer automatically.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
ab8ee776b9 P2PS: Provision Discovery fail event
This extends P2P-PROV-DISC-FAILURE with adv_id and deferred_session_resp
in P2PS cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
1300cc8e8f P2PS: PD Request processing and PD Response building
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
5fefce2747 P2PS: Callback to send P2PS provisioning events
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
9a58e521ac P2PS: Callback to create pending group after sending PD Response
This introduces a P2P module callback function that will be used to
create the pending P2PS group after sending PD Response and receiving
ACK status for it.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
895d94def9 P2PS: Callback to remove stale persistent groups
When the peer device is trying to form a new group despite having
old persistent group with same roles, remove the stale persistent
group.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
6d9085145c P2PS: Process P2PS provisioning commands
This extends wpas_p2p_prov_disc() implementation to accept P2PS
parameters. None of the callers are yet using this functionality; the
following commit introduces a user.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
369678ad14 P2PS: Add P2PS attributes into PD Request if requested
This adds a data structure for storing P2PS PD information and code to
add the related attributes into PD Request. The actual operation to
trigger this behavior will be added in a separate commit.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:07 +02:00
Krishna Vamsi
d4b43b5886 P2PS: Add support to send ASP-RESP events
Send P2P-SERV-ASP-RESP events upon receiving GAS responses with
ASP services.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:06 +02:00
Krishna Vamsi
6df08d0341 P2PS: Logic to parse GAS requests for ASP services
Add support to parse received GAS requests for ASP services and
prepare GAS responses accordingly.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:06 +02:00
Krishna Vamsi
5a4102ce0e P2PS: Add support to send ASP service requests
This extends the P2P_SERV_DISC_REQ control interface command with a new
"asp" service type. This takes service id, service string, and optional
service info as arguments.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-02-03 01:35:06 +02:00