Mark a channel as required DFS based on regulatory information received
from the driver/kernel rather than deciding based on hardcoded
boundaries on the frequency. Previously few channels were being marked
as requiring DFS even though they were non-DFS in a particular country.
If the driver does not provide channel list information, fall back to
the previously used frequency-based determination.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Extend wpa_supplicant WNM-Notification RX handling to parse and process
received Terms and Conditions Acceptance notifications. If PMF is
enabled for the association, this frame results in control interface
indication (HS20-T-C-ACCEPTANCE <URL>) to get upper layers to guide the
user through the required acceptance steps.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
CCMP group cipher was removed if CCMP was not allowed as a pairwise
cipher when loading a configuration file (but not actually when changing
configuration during runtime). This is needed to avoid issues with
configurations that use the default group cipher (TKIP CCMP) while
modifying pairwise cipher from the default CCMP TKIP) to TKIP. However,
there is not really a need to remove the CCMP group cipher if any GCMP
or CCMP cipher is enabled as a pairwise cipher.
Change the network profile validation routine to not remove CCMP as
group cipher if CCMP-256, GCMP, or GCMP-256 is enabled as a pairwise
cipher even if CCMP is not.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When AP initialization is completed in a callback (e.g., OBSS scan),
wpa_supplicant_deinit_ap() is not called in case of failure. Fix this by
calling setup_complete_cb in case of failure, too, which in turn calls
wpa_supplicant_deinit_ap() if needed.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Add WPA FT auth to connect params in case of a re-connection to ESS
supporting FT when FT was used in the first connect.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Add MDE (mobility domain element) to Association Request frame IEs in
the driver assoc params. wpa_supplicant will add MDE only if the network
profile allows FT, the selected AP supports FT, and the mobility domain
ID matches.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
This makes wpa_supplicant add Hotspot 2.0 Roaming Consortium Selection
element into (Re)Association Request frames if the network profile
includes roaming_consortium_selection parameter.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds new roaming_consortium_selection network profile parameter
into wpa_supplicant. This is used to store the OI that was used for
network selection (INTERWORKING_SELECT) based on matching against the
Roaming Consortium OIs advertised by the AP. This can also be used when
using an external component to perform selection.
This commit adds the network profile parameter, but does not yet include
it in (Re)Association Request frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends Hotspot 2.0 credential matching to consider the
roaming_consortiums parameter when determining whether the cred block
matches the information advertised by an AP.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new string parameter contains a comma delimited list of OIs
(hexdump) in a string. This is used to store Hotspot 2.0
PerProviderSubscription/<X+>/HomeSP/RoamingConsortiumOI. This commit
includes the configuration changes to parse and write the parameter. The
actual values are not yet used in Interworking network selection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends wpa_supplicant Hotspot 2.0 ANQP routines to allow the
Operator Icon Metadata ANQP-element to be fetched with "ANQP_GET <bssid>
hs20:12". The result is available in the new hs20_operator_icon_metadata
entry in the "BSS <bssid>" output.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Timeout is increased by dfs_cac_ms from channel data, or by max CAC time
(10 minutes) if dfs_cac_ms is not defined. This is needed for some more
complex cases, e.g., when STA is acting as an active slave with DFS
offload enabled and decided to start CAC after receiving CONNECT
command, in such a case the 10 second timeout is too small and
wpa_supplicant need to wait for CAC completion or CAC timeout (up to 10
minutes).
Without such timeout modification wpa_supplicant will be unable to
connect to an AP on DFS channel, since the default authentication
timeout (10 s) is smaller than the minimum CAC time (60 s).
Tested with nl80211 DFS offload implementation.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Rename DFS event handling functions, since they are located in ap.c and
refer to AP-mode only. Needed to add some STA-mode DFS event handling.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
The recently introduced sae_password parameter was only handled properly
in wpa_supplicant/sme.c while wpa_supplicant/mesh.c assumed that
ssid->passphrase exclusively holds the secret.
Import the logic from sme.c to mesh.c to allow having only sae_password
set which otherwise throws this error:
AP-ENABLED
mesh: Passphrase for SAE not configured
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Explicitly check the PMKSA cache entry to have matching SAE AKMP for the
case where determining whether to use PMKSA caching instead of new SAE
authentication. Previously, only the network context was checked, but a
single network configuration profile could be used with both WPA2-PSK
and SAE, so should check the AKMP as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The RSN supplicant state machine PMK was set based on WPA PSK even for
the cases where SAE would be used. If the AP allows PMKSA caching to be
used with SAE, but does not indicate the selected PMKID explicitly in
EAPOL-Key msg 1/4, this could result in trying to use the PSK instead of
SAE PMK. Fix this by not setting the WPA-PSK as default PMK for SAE
network profiles and instead, configuring the PMK explicitly from the
found PMKSA cache entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of these were not preceded by wpa_hexdump_key(PSK) which made it
more difficult to interpret the debug log.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no existing mechanism for setting up AP mode functionality with
FT enabled, so there is not really much point in having a build option
for trying to include the AP-to-AP FT functionality into wpa_supplicant
either. Since this build option results in failures to complete the
build, simply remove it completely. This can be restored if there is
ever desire to enable FT functionality in wpa_supplicant controlled AP
mode.
Signed-off-by: Jouni Malinen <j@w1.fi>
When wpa_supplicant is running on a Linux interface that is configured in
promiscuous mode, and it is not a member of a bridge, incoming EAPOL
packets are processed regardless of the Destination Address in the frame.
As a consequence, there are situations where wpa_supplicant replies to
EAPOL packets that are not destined for it.
This behavior seems undesired (see IEEE Std 802.1X-2010, 11.4.a), and can
be avoided by attaching a BPF filter that lets the kernel discard packets
having pkt_type equal to PACKET_OTHERHOST.
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
Previously we set this flag to one in wpa_supplicant_init_iface() if
Wi-Fi controller does not have a dedicated P2P-interface.
This setting had effect only in scope of wpa_supplicant_init_iface() and
it contradicts with comment to struct wpa_interface::p2p_mgmt field.
This comment says that this flag is used only if Wi-Fi controller has
dedicated P2P-device interface.
Also it contradicts with usage of similiar p2p_mgmt field in struct
wpa_supplicant. Again struct wpa_supplicant::p2p_mgmt is set only for
dedicated P2P-device interface.
After this change wpa_interface become input argument to
wpa_supplicant_init_iface() that we are not modifying.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
This fixes sending of FindStopped, GroupFormationFailure, and
InvitationReceived signals in the case of separate P2P-Device interface.
This extends the coverage of the earlier commit
745d62322b ("dbus: Redirect P2P request to
the managment device if present") to these three functions that were
missing the redirection.
Some wireless controllers might have separate P2P-Device interface, see
as example result of 'iw dev':
phy#0
Unnamed/non-netdev interface
...
type P2P-device
...
Interface wlp2s0
type managed
...
In this case there is separate 'struct wpa_supplicant' created for this
p2p-dev-* device as result of 'wpa_supplicant_add_iface >
wpas_p2p_add_p2pdev_interface > wpa_supplicant_add_iface'.
This instance of wpa_supplicant is not registered in D-Bus
(wpas_dbus_register_*) since for corresponding P2P device interface flag
'struct wpa_interface > p2p_mgmt' is set.
But this instance is saved in p2p_init_wpa_s and is used for handling
P2P related D-Bus commands. Therefore we should look for D-Bus path in
the parent of p2p_init_wpa_s instance.
Without this change test dbus_p2p_discovery starts failing if we set
support_p2p_device in vm-run.sh.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
If any of the interfaces supports FILS (and similarly for FILS-SK-PFS),
include the "fils" (and "fils_sk_pfs") capability in D-Bus information.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Add examples of relevant top level CONFIG clauses for wpa_supplicant
MACsec support to defconfig.
Extend the example of MACsec related network configuration. Also bring
them in line with the format of the other example network configurations.
Signed-off-by: Jaap Keuter <jaap.keuter@xs4all.nl>
In the current implementation, upon an EAP method failure, followed by
an EAP failure, the EAP Status is propagated up in wpa_supplicant with a
general failure parameter string "failure". This parameter is used for a
notification on the dbus.
This commit reports the EAP method failure error code in a separate
callback.
The solution in this commit is generic to all EAP methods, and can be
used by any method that need to pass its error code. However, this
commit only implements the reporting for EAP-SIM and EAP-AKA methods
where the Notification Code (in AT_NOTIFICATION) is used as the method
specific error code value.
Signed-off-by: Ahmed ElArabawy <arabawy@google.com>
When connecting to a WPA-EAP network and the MAC address is changed
just before the association (for example by NetworkManager, which sets
a random MAC during scans), the authentication sometimes fails in the
following way ('####' logs added by me):
wpa_supplicant logs:
wlan0: WPA: RX message 1 of 4-Way Handshake from 02:00:00:00:01:00 (ver=1)
RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: PMKID in EAPOL-Key - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
RSN: PMKID from Authenticator - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
wlan0: RSN: no matching PMKID found
EAPOL: Successfully fetched key (len=32)
WPA: PMK from EAPOL state machines - hexdump(len=32): [REMOVED]
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 66 20 cf ab 8c dc
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): ea 73 67 b1 8e 5f 18 43 58 24 e8 1c 47 23 87 71
RSN: Replace PMKSA entry for the current AP and any PMKSA cache entry that was based on the old PMK
nl80211: Delete PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKSA cache entry free_cb: 02:00:00:00:01:00 reason=1
RSN: Added PMKSA cache entry for 02:00:00:00:01:00 network_ctx=0x5630bf85a270
nl80211: Add PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKID mismatch - authentication server may have derived different MSK?!
hostapd logs:
WPA: PMK from EAPOL state machine (MSK len=64 PMK len=32)
WPA: 02:00:00:00:00:00 WPA_PTK entering state PTKSTART
wlan1: STA 02:00:00:00:00:00 WPA: sending 1/4 msg of 4-Way Handshake
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 02 00 00 00 00 00
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: Send EAPOL(version=1 secure=0 mic=0 ack=1 install=0 pairwise=1 kde_len=22 keyidx=0 encr=0)
That's because wpa_supplicant computed the PMKID using the wrong (old)
MAC address used during the scan. wpa_supplicant updates own_addr when
the interface goes up, as the MAC can only change while the interface
is down. However, drivers don't report all interface state changes:
for example the nl80211 driver may ignore a down-up cycle if the down
message is processed later, when the interface is already up. In such
cases, wpa_supplicant (and in particular, the EAP state machine) would
continue to use the old MAC.
Add a new driver event that notifies of MAC address changes while the
interface is active.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Add an event callback for EVENT_STATION_OPMODE_CHANGED to allow
user/application to get the notification whenever there is a change in a
station's HT/VHT op mode.
The new events:
STA-OPMODE-MAX-BW-CHANGED <addr> <20(no-HT)|20|40|80|80+80|160>
STA-OPMODE-SMPS-MODE-CHANGED <addr> <automatic|off|dynamic|static>
STA-OPMODE-N_SS-CHANGED <addr> <N_SS>
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
To retain configurator information across hostapd/wpa_supplicant
restart, private key need to be maintained to generate a valid pair of
authentication keys (connector, netaccess_key, csign) for new enrollees
in the network.
Add a DPP_CONFIGURATOR_GET_KEY control interface API through which the
private key of an existing configurator can be fetched.
Command format:
DPP_CONFIGURATOR_GET_KEY <configurator_id>
The output from this command can then be used with
"DPP_CONFIGURATOR_ADD key=<hexdump>" to create the same key again.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This extends dpp_test functionality to allow DPP exchanges to be stopped
after authentication is completed on the Initiator, i.e., after sending
out the Authentication Confirm message. Previously, dpp_test=89 was used
only on the Responder side to stop after receiving the Authentication
Confirm message. The main use case for this extended functionality is to
be able to stop the protocol exchange on a device that acts as
authentication Initiator and Enrollee.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
In case MKA is initialized successfully, local copies of CAK and CKN
were allocated, but never freed. Ensure that such memory is released
also when ieee802_1x_kay_create_mka() returns a valid pointer.
Fixes: ad51731abf ("wpa_supplicant: Allow pre-shared (CAK,CKN) pair for MKA")
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
When the driver indicates that the connection is authorized (i.e., the
4-way handshake was completed by the driver), cancel the EAP
authentication timeout and set the EAP state machine to success state.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
wpa_passphrase requires libcrypto from OpenSSL (or another selected
library). User can set an alternative path to OpenSSL libraries by
defining LIBS at the top of .config but if $(LIBS) is not actually used
wrong libcrypto is used or compilation fails if there is no libcrypto in
the default locations cc is looking for it. It's especially bad for
cross-compilers that fail with 'cannot find -lcrypto' message.
Signed-off-by: Arkadiusz Drabczyk <arkadiusz@drabczyk.org>
This header file pulls in an OpenSSL header file and as such, should not
be included without CONFIG_DPP=y to avoid bringing in an unnecessary
build dependency on OpenSSL header files.
Signed-off-by: Jouni Malinen <j@w1.fi>
Force use of the wildcard BSSID address in GAS query frames with DPP
regardless of how the gas_address3 configuration parameter is set. DPP
specification mandates this and the use of GAS here is really outside
the context of a BSS, so using the wildcard BSSID makes sense even for
the corner case of Configurator running on a known AP (where IEEE 802.11
standard would allow the BSSID of the AP to be used).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If a DPP_STOP_LISTEN call happens to be received when there is a pending
gas-query radio work that has not yet been started, it was possible for
gas_query_stop() to go through gas_query_done() processing with
gas->work == NULL and that ended up with the pending GAS query getting
freed without removing the pending radio work that hold a reference to
the now freed memory. Fix this by removing the pending non-started radio
work for the GAS query in this specific corner case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for wpa_supplicant to try to initiate PKEX on 5 GHz and 60
GHz bands in addition to the previously available 2.4 GHz case. If no
response from a peer device is seen on the 2.4 GHz band (channel 6) for
the five attempts, try the other PKEX channels (5 GHz channels 44 and
149; and 60 GHz channel 2) if they are supported and allowed for
initiating radiation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Previously, wpa_supplicant set PMF as optional for the DPP AKM since
there was no clear statement about this requirement in the tech spec.
Now that this requirement has been added, update the implementation to
match. In addition, set ssid->ieee80211w using the actual enum
mfp_options values instead of magic constants to make this a bit more
readable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If the -I<config> argument is used and the referenced configuration file
cannot be parsed, wpa_config_read() ended up freeing the main
configuration data structure and that resulted in use of freed memory in
such an error case. Fix this by not freeing the main config data and
handling the error case in the caller.
Signed-off-by: Jouni Malinen <j@w1.fi>
If option -I:config points to a non-existing file, the the previously
allocated config must not be freed. Avoid use of freed memory in such an
error case by skipping the incorrect freeing operation.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
The special case of returning from wpa_supplicant_set_suites() when OWE
transition mode profile is used for an open association did not clear
the wpa_ie buffer length properly. This resulted in trying to use
corrupted IEs in the association request and failed association
(cfg80211 rejects the request or if the request were to go out, the AP
would likely reject it).
Signed-off-by: Jouni Malinen <j@w1.fi>
This functionality can be used regardless of P2P and should not be under
the ifdef of CONFIG_P2P.
Signed-off-by: Simon Dinkin <simon.dinkin@tandemg.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This was supposed to be an array of const-pointers to const-char; not
something duplicating const for char and resulting in compiler warnings
with more recent gcc versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
Extend the SME functionality to support the external authentication.
External authentication may be used by the drivers that do not define
separate commands for authentication and association
(~WPA_DRIVER_FLAGS_SME) but rely on wpa_supplicant's SME for the
authentication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows a separate configuration parameter (imsi_identity) to be
used in EAP-SIM/AKA/AKA' profiles to override the identity used in MK
derivation for the case where the identity is expected to be from the
last AT_IDENTITY attribute (or EAP-Response/Identity if AT_IDENTITY was
not used). This may be needed to avoid sending out an unprotected
permanent identity information over-the-air and if the EAP-SIM/AKA
server ends up using a value based on the real IMSI during the internal
key derivation operation (that does not expose the data to others).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the OWE network profile matches an open network which does not
advertise OWE BSS, allow open connection. The new owe_only=1 network
profile parameter can be used to disable this transition mode and
enforce connection only with OWE networks.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
GnuTLS-based builds can now be done using either libnettle or libgcrypt
for crypto functionality:
CONFIG_TLS=gnutls
CONFIG_CRYPTO=nettle
CONFIG_TLS=gnutls
CONFIG_CRYPTO=gnutls
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the internal HMAC MD5, SHA-1, and SHA256 implementations with
the ones from libgcrypt and also add the SHA384 and SHA512 versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
Replace the internal SHA256 implementation with the one from libgcrypt
and also add the SHA384 and SHA512 versions.
Signed-off-by: Jouni Malinen <j@w1.fi>
If a specific DH group for OWE is not set with the owe_group parameter,
try all supported DH groups (currently 19, 20, 21) one by one if the AP
keeps rejecting groups with the status code 77.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of requiring OpenSSL headers to be available just for the
SSL3_RANDOM_SIZE definition, replace that macro with a fixed length (32)
to simplify dependencies.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new disable_fils parameter can be used to disable FILS functionality
in the driver. This is currently removing the FILS Capability bit in
Extended Capabilities and providing a callback to the driver wrappers.
driver_nl80211.c implements this using a QCA vendor specific command for
now.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 265bda3444 ('OWE: Allow DH
Parameters element to be overridden for testing purposes') provided
means for using "VENDOR_ELEM_ADD 13 <IE>" in OWE protocol testing, but
that commit covered only the sme.c case (i.e., drivers that use
wpa_supplicant SME). Extend this to cover drivers that use internal SME
(e.g., use the nl80211 Connect command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Wpa_supplicant's random pool is not necessary on Android. Randomness
is already provided by the entropymixer service which ensures
sufficient entropy is maintained across reboots. Commit b410eb1913
'Initialize /dev/urandom earlier in boot' seeds /dev/urandom with
that entropy before either wpa_supplicant or hostapd are run.
Signed-off-by: Jeff Vander Stoep <jeffv@google.com>
If a credential with encp type AES is received, add GCMP-256 and
CCMP-256 cipher options on station Enrollee based on local capabilities.
This is needed to allow connection with an AP using either of these
newer ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The credential MAC address is not necessarily that of the AP, i.e., it
is more likely to be that of the Enrollee. Check the scan results
against the current BSSID as well if match is not found otherwise when
going through the mixed mode workaround.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The previously used 10 second timer did not really make much sense since
the Initiator is not going to be waiting for the response that long.
Change this to 1 second based on the DPP tech spec change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes the full DPP deinit operation more consistent with stopping
of a single operation. In practice, this adds the new GAS client
stopping functionality.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously this stopped only the DPP Authentication instance, but it is
better to clear both PKEX and Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
An additional TX status callback could result in processing the DPP
authentication completion another time at least with hostapd. Fix this
by clearing the dpp_auth_ok_on_ack when processing it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add CONFIG_TESTING_OPTIONS ifdef protection to couple of forgotten DPP
test parameters in wpa_supplicant ctrl_iface.
Signed-off-by: Ashok Ponnaiah <aponnaia@qti.qualcomm.com>
It was possible for a timeout from an old GAS server operation to
trigger DPP configuration failure during the subsequent DPP operation.
Fix this by verifying that the status callback is for the response
generated during the same DPP Authentication/Configuration exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Configurator signing its own Connector was previously supported only in
wpa_supplicant. This commit extends that to hostapd to allow an AP
acting as a Configurator to self-configure itself.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows external applications to get event indication for Probe
Request frames. Extend ctrl iface cmd "ATTACH" to enable this event on
per-request basis. For example, user has to send ctrl iface cmd "ATTACH
probe_rx_events=1" to enable the Probe Request frame events.
Signed-off-by: bhagavathi perumal s <bperumal@qti.qualcomm.com>
Previous implementation did not handle number of sequences correctly.
Make sure the iteration continues in both unicast and broadcast cases
until the five attempts have been made. In addition, improve timing by
checking 10 second time from the beginning of each iteration round and
not the last channel on which the Auth Req frame has been transmitted.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the Authentication Request frame was retried after 2+10 = 12
seconds since the wait for the response was not accounted for. Substract
that wait from the 10 second wait time to start the retries more quickly
based on the 10 second timer described in the tech spec.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If unicast Authentication Request frame is used and the peer ACKs such a
frame, but does not reply within the two second limit, there is no need
to continue trying to retransmit the request frames since the peer was
found, but not responsive.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new conf={sta,ap}-{sae,psk-sae} parameter values can now be used to
specify that the legacy configuration object is for SAE.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows DPP to be used for enrolling credentials for SAE networks in
addition to the legacy PSK (WPA-PSK) case. In addition, enable FT-PSK
and FT-SAE cases automatically.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Retransmit the PKEX Exchange Request frame if no response from a peer is
received. This makes the exchange more robust since this frame is sent
to a broadcast address and has no link layer retries.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to allow more invalid attribute values to be written
into Peer Discovery Request/Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Extend dpp_test to cover a case where Config Attrib Object value is
invalid in Configuration Request frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant DPP implementation to retransmit DPP
Authentication Response frame every 10 seconds up to 5 times if the peer
does not reply with DPP Authentication Confirm frame.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, this command stopped listen operation immediately, but if
there was an ongoing authentication exchange, a new listen operation was
started. This is not really expected behavior, so stop the
authentication exchange first with this command to avoid restarting
listen operation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new role=either parameter can now be used with DPP_AUTH_INIT to
indicate that the initiator can take either the Configurator or Enrollee
role.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends wpa_supplicant to iterate over all available channels from
the intersection of what the peer indicates and the local device
supports when initiating DPP Authentication. In addition, retry DPP
Authentication Request frame up to five times if no response is
received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Generate the PKEX bootstrapping information and release the PKEX session
in a helper function that both the initiator and responder can use
instead of maintaining this functionality separately in two places.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit introduces the ACS functionality for the autonomous GO. The
optional parameter <freq> in p2p_group_add is enhanced to carry a value
"acs" with the intention to select the channels among any supported
band. freq = 2 / 5 carry the need to select the channels only in the
respective bands 2.4 / 5 GHz. This functionality is on top of the host
driver's capability to offload ACS, which is advertized through
WPA_DRIVER_FLAGS_ACS_OFFLOAD.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add limit on number of failed attempts that could have used PKEX code.
If the limit (5) is reached, drop the PKEX state (including the code)
and report this on the control interface to indicate that a new code
needs to be entered due to possible attack.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Clean up the pending PKEX exchange if Commit-Reveal Request processing
indicates a mismatch in the PKEX code. Previously, the this case was
silently ignored and the session was left in pending state that
prevented new PKEX exchanges from getting initated. Now, a new attempt
is allowed to be initiated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Report mismatching finite cyclic group with PKEX Exchange Response using
STATUS_BAD_GROUP and provide more detailed error report over the control
interface on the peer device when this happens.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Indicate to upper layers if PKEX Commit-Reveal Request frame AES-SIV
decryption fails. That is a likely sign of the PKEX code mismatch
between the devices.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP AKM should really require PMF to be used, but since that is not yet
explicitly required in the specification, make PMF enabled for now. For
legacy PSK cases, configure PMF to be enabled as well to support both
APs in no-PMF, optional-PMF, and required-PMF configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow the Initiator to request a different channel to be used for DPP
Authentication and DPP Configuration exchanges. This commit adds support
for this in wpa_supplicant with the optional neg_freq=<freq in MHz>
parameter in DPP_AUTH_INIT.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant dpp_config_obj_override,
dpp_discovery_override, and dpp_groups_override parameters to be cleared
by setting them to a zero-length value.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for protocol testing purposes and UI needs to display
more detailed information about DPP exchanges.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Both the DPP-TX and DPP-TX-STATUS events are provided.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is helpful for testing purposes and also for upper layer components
that may want to show more detailed progress through a DPP exchange.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Now that dpp_check_attrs() takes care of verifying that no attributes
are after the Wrapped Data attribute, the duplicated checks in hostapd
and wpa_supplicant side of the implementation can be removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a generic mechanism for configuring the DPP implementation to behave
in particular different (mostly incorrect) ways for protocol testing
purposes. The new dpp_test parameter can be set to a non-zero integer to
indicate a specific behavior. This is only available in
CONFIG_TESTING_OPTIONS=y builds.
This commit include cases for an extra attribute being added after the
Wrapped Data attribute and Initiator/Responder capabilities having an
unexpected zero capability.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Seems like some test cases, e.g., ap_wpa2_psk_ext_retry_msg_3c, require
larger buffer than 256 bytes.
In other case I fail such test cases when run on real HW and using:
CONFIG_CTRL_IFACE=udp-remote
Increase the RX buffer from 256 to 4096 bytes to match the other control
interface cases.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
After an initial connection wpa_supplicant derives ERP information which
can be used in doing eventual authentications in the same realm. This
information can be used by drivers with offloaded FILS support to do
driver/firmware initiated roamings. Add support to send this updated
information to such drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed to be able to use the same implementation for updating
the connection parameters in the driver during an association.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the replay counter after a roam for all cases. This restores the
design back to what it was before commit
01ef320f19 ('FILS: Update ERP next
sequence number with driver offload').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant RESEND_ASSOC command can be used to request the
last (Re)Association Request frame to be sent to the AP to test FT
protocol behavior.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new wpa_supplicant "KEY_REQUEST <error=0/1> <pairwise=0/1>" command
can be used to request an EAPOL-Key Request frame to be sent to the AP.
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This can be used to test replay protection. The "RESET_PN" command in
wpa_supplicant and "RESET_PN <addr>" command in hostapd resets the local
counters to zero for the last configured key. For hostapd, the address
parameter specifies which STA this operation is for or selects GTK
("ff:ff:ff:ff:ff:ff") or IGTK ("ff:ff:ff:ff:ff:ff IGTK").
This functionality is for testing purposes and included only in builds
with CONFIG_TESTING_OPTIONS=y.
Signed-off-by: Jouni Malinen <j@w1.fi>
This was originally added to allow the IEEE 802.11 protocol to be
tested, but there are no known fully functional implementations based on
this nor any known deployments of PeerKey functionality. Furthermore,
PeerKey design in the IEEE Std 802.11-2016 standard has already been
marked as obsolete for DLS and it is being considered for complete
removal in REVmd.
This implementation did not really work, so it could not have been used
in practice. For example, key configuration was using incorrect
algorithm values (WPA_CIPHER_* instead of WPA_ALG_*) which resulted in
mapping to an invalid WPA_ALG_* value for the actual driver operation.
As such, the derived key could not have been successfully set for the
link.
Since there are bugs in this implementation and there does not seem to
be any future for the PeerKey design with DLS (TDLS being the future for
DLS), the best approach is to simply delete all this code to simplify
the EAPOL-Key handling design and to get rid of any potential issues if
these code paths were accidentially reachable.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 03ed0a5239 ('WNM: Ignore WNM-Sleep
Mode Response if WNM-Sleep Mode has not been used') started ignoring the
response when no WNM-Sleep Mode Request had been used during the
association. This can be made tighter by clearing the used flag when
successfully processing a response. This adds an additional layer of
protection against unexpected retransmissions of the response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
The new sae_password network profile parameter can now be used to set
the SAE password instead of the previously used psk parameter. This
allows shorter than 8 characters and longer than 63 characters long
passwords to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While considering the movement of P2P GO from its current operating
channel, do not mark a DFS channel as invalid if DFS is offloaded
to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wpas_p2p_select_go_freq_no_pref() ended up selecting a 2.4
GHz band channel first before even considering 5 or 60 GHz channels.
This was likely done more or less by accident rather than by design when
the 5 GHz and 60 GHz band extensions were added. It seems reasonable to
enhance this by reordering the code to start with 5 and 60 GHz operating
classes and move to 2.4 GHz band only if no channel was available in 5
or 60 GHz bands for P2P GO use.
This does have some potential interop issues with 2.4 GHz only peer
devices when starting up an autonomous GO (i.e., without there being
prior knowledge of channels that the peers support). Upper layers are
expected to enforce 2.4 GHz selection if that is needed for some use
cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows CONFIG_TESTING_OPTIONS=y builds of wpa_supplicant to
override the OWE DH Parameters element in (Re)Association Request frames
with arbitrary data specified with the "VENDOR_ELEM_ADD 13 <IE>"
command. This is only for testing purposes.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This additional field was added to DPP Public Action frames in DPP tech
spec v0.2.3 to support cryptographic agility in the future.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only the SME-in-wpa_supplicant case was supported. This
extends that to cover the drivers that implement SME internally (e.g.,
through the cfg80211 Connect command).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in wpa_supplicant to allow DH groups 20 and 21
to be used in addition to the mandatory group 19 (NIST P-256). The group
is configured using the new network profile parameter owe_group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This extends OWE support in hostapd to allow DH groups 20 and 21 to be
used in addition to the mandatory group 19 (NIST P-256).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for using the OWE Transition Mode element to determine the
hidden SSID for an OWE BSS that is used in transition mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
sm->pmk_len was not set when deriving the PMK as part of OWE key
generation. This depending on wpa_sm_set_pmk_from_pmksa() call resetting
the value to the default. While this worked for many cases, this is not
correct and can have issues with network profile selection based on
association information. For example, the OWE transition mode cases
would hit an issue here.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds new wpa_supplicant configuration parameters (go_interworking,
go_access_network_type, go_internet, go_venue_group, go_venue_type) to
add a possibility of configuring the P2P GO to advertise Interworking
element.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the default scan IEs when OCE is enabled/disabled to the
driver/firmware, so that the correct IEs will be sent out by the
driver/firmware in Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new wpa_supplicant network parameter group_mgmt can be used to
specify which group management ciphers (AES-128-CMAC, BIP-GMAC-128,
BIP-GMAC-256, BIP-CMAC-256) are allowed for the network. If not
specified, the current behavior is maintained (i.e., follow what the AP
advertises). The parameter can list multiple space separate ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds phase1 parameter tls_suiteb=1 into wpa_supplicant
configuration to allow TLS library (only OpenSSL supported for now) to
use Suite B 192-bit level rules with RSA when using >= 3k (3072) keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new psk=<hexdump> can be used as an alternative to pass=<passphrase>
when configuring the DPP Configurator with a legacy network parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wowlan_triggers were updated in kernel only during startup.
Also update it whenever it is set from the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the code that writes mesh_rssi_threshold to a network block
always executes, but the code that reads it from network block and the
code that initializes it to a default value in a new network block are
inside #ifdef CONFIG_MESH. As a result when writing a config file it
will write mesh_rssi_threshold (since it has a non-default value) and
later fail to read the network block.
Fix this by moving the write code under #ifdef CONFIG_MESH as well.
Note, network blocks which already have mesh_rssi_threshold because of
the bug will still fail to read after the fix.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The introduction of radio works and a delayed callback to complete
association/connection requests ended up breaking RSN pre-authentication
candidate list generation for the case of pre-connection scan results.
Previously, wpa_supplicant_associate() set the RSN state machine
configuration before returning and the calls to
wpa_supplicant_rsn_preauth_scan_results() immediately after this
function call were working fine. However, with the radio work callback,
the RSN state machine configuration started to happen only in that
callback which would be called soon after this code path has completed.
This resulted in the RSN state machine not knowing the selected SSID and
as such, rejecting all pre-authentication candidates.
Fix this by setting the RSN state machine configuration from
wpa_supplicant_associate() so that the existing callers of
wpa_supplicant_rsn_preauth_scan_results() can be used as-is to add
candidates for pre-authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
secy_init_macsec() can fail (if ->macsec_init fails), and
ieee802_1x_kay_init() should handle this and not let MKA run any
further, because nothing is going to work anyway.
On failure, ieee802_1x_kay_init() must deinit its kay, which will free
kay->ctx, so ieee802_1x_kay_init callers (only ieee802_1x_alloc_kay_sm)
must not do it. Before this patch there is a double-free of the ctx
argument when ieee802_1x_kay_deinit() was called.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
When building wpa_ie in wpas_start_assoc_cb() with ext_capab,
make sure that assignment does not exceed max_wpa_ie_len.
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
This introduces a new interface for mesh and adds a signal that
is similar to the control interface event MESH-GROUP-STARTED.
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
DPP tech spec changed the contents of these frames by replacing the
public key hash attributes with a Transaction ID attribute that gets
copied from the request to the response to identify the transaction in a
simpler manner.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, CONFIG_WNM enabled build that supports WNM for both
station mode and AP mode. However, in most wpa_supplicant cases only
station mode WNM is required and there is no need for AP mode WNM.
Add support to differentiate between station mode WNM and AP mode
WNM in wpa_supplicant builds by adding CONFIG_WNM_AP that should be
used when AP mode WNM support is required in addition to station mode
WNM. This allows binary size to be reduced for builds that require
only the station side WNM functionality.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When setting the frequencies for beacon report request scan, it is
possible that a frequency is added twice (e.g., when the same channel
appears both in the channel field and in the AP channel report
subelement). This may cause the scan request to fail.
Make sure the frequencies array contains no duplications before
requesting the scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Send Radio Measurement response with measurement mode set to reject
in the following cases:
1. Reporting conditions is not supported.
2. No valid channels found for the measurement
Sending a response with an incapable indication will stop the AP from
sending other measurement requests of the same type as specified
in IEEE Std 802.11-2016, 11.11.6.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When failing to trigger scan for beacon report (e.g., when the
requested duration is not supported by the driver), send a
Radio Measurement response with the mode set to refused and don't
retry the scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
IEEE Std 802.11-2016, 11.11.6 specifies that a station that is unable to
make a requested measurement or refuses to make a measurement shall
respond only if the measurement request was received within an
individually addressed radio measurement request frame, but shall not
respond if such a request was received in a group addressed frame.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Add a build option to select different default ciphers for OpenSSL
instead of the hardcoded default "DEFAULT:!EXP:!LOW".
This new option is useful on distributions where the security level
should be consistent for all applications, as in Fedora [1]. In such
cases the new configuration option would be set to "" or
"PROFILE=SYSTEM" to select the global crypto policy by default.
[1] https://fedoraproject.org/wiki/Changes/CryptoPolicy
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
If an AP is not FILS capable and wpa_supplicant has a saved network
block for the network with FILS key management and a saved erp info,
wpa_supplicant might end up issuing a FILS connection to a non-FILS AP.
Fix this by looking for the presence of FILS AKMs in wpa_s->key_mgmt,
i.e., after deciding on the AKM suites to use for the current
connection.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
In case that an mbo object is allocated, but there is a failure
to resize the wpabuf, need to free the mbo object.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Scan results with parent TSF older than the scan start TSF are not added
to the beacon report since they are considered as scan results from
previous scans. However, for drivers that report the scan start TSF but
not the parent TSF of each scan result, the parent TSF will be zero so
valid scan results will be dropped.
Fix this by filtering scan results by the parent TSF only if the
driver supports reporting the parent TSF for each scan result.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Clear the get_pref_freq_list_override in p2p_ctrl_flush(). This fixes
the case when a dedicated P2P device interface is used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
dpp.h file requires openssl in order to compile, which breaks
compilation on systems without it.
Move DPP_OUI_TYPE to ieee802_11_defs.h and don't include dpp.h when
not really needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
If a DFS forced frequency is provided in 'p2p_group_add' and the driver
supports DFS offload, the frequency was rejected in
wpas_p2p_init_go_params(). However, it was accepted in
wpas_p2p_select_go_freq() and wpas_p2p_group_add(). To make the behavior
consistent, the DFS frequency is now accepted in
wpas_p2p_init_go_params() similar to the way done in
wpas_p2p_select_go_freq().
Redundant check in wpas_p2p_group_add() for DFS forced frequency is
removed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add changes to control interface command get_capability to advertize
FILS capability, FILS AKMs suites, and FILS Authentication algorithms
based on the driver capabilities.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support to scan for a specific BSSID through the wpa_supplicant
control interface.
Usage: wpa_cli scan bssid=ab:bc:cd🇩🇪ef:12
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The DPP Configurator can use this new command to generate its own signed
connector for the network that it manages.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
All the arguments to this command are optional, so do not mandate at
least one to be included in wpa_cli.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows wpa_supplicant to be configured to act as the configurator
in the case where a peer device initiates DPP Authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This implements genric PKEX functionality in src/common/dpp.c and glue
code to use this in wpa_supplicant (i.e, hostapd DPP implementation does
not yet support PKEX).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new pass=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the passphrase to use in config object.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new ssid=<hexdump> parameter to DPP_AUTH_INIT can now be used to
specify the SSID to use in config object.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This script can be used to process Android logcat information for
scanned QR Codes (e.g., from Barcode Scanner app) and also to display QR
Codes for locally generated bootstrap keys.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant can now be configured to generate a network profile
automatically based on DPP configuration. The following
dpp_config_processing values can be used to specify the behavior:
0 = report received configuration to an external program for
processing; do not generate any network profile internally (default)
1 = report received configuration to an external program and generate
a network profile internally, but do not automatically connect
to the created (disabled) profile; the network profile id is
reported to external programs
2 = report received configuration to an external program, generate
a network profile internally, try to connect to the created
profile automatically
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Commit 5538fc9309 ('FILS: Track completion
with FILS shared key authentication offload') added an additional case
for calling wpa_supplicant_event_assoc_auth() from EVENT_ASSOC handling
in case of FILS-completion with driver-based-SME. However, that checked
what placed outside the data != NULL case while data != NULL needs to
apply for this case as well due to wpa_supplicant_event_assoc_auth()
behavior. Move the data != NULL check to apply to both cases to avoid
potentially issues if a driver interface were to return EVENT_ASSOC
without the associate data. (CID 164708)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
While encoded == NULL could happen in the case of an empty blob, that
will result in encoded_len == 0 and base64_decode() not derefencing the
src argument. That seems to be too difficult for some static analyzers,
so to avoid false warnings, explicitly reject the encoded == NULL case
without even trying to base64 decode it. (CID 164709)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This new AKM is used with DPP when using the signed Connector to derive
a PMK. Since the KCK, KEK, and MIC lengths are variable within a single
AKM, this needs number of additional changes to get the PMK length
delivered to places that need to figure out the lengths of the PTK
components.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds DPP bootstrapping, authentication, and configuration into
hostapd similarly to how the design was integrated in wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds support for DPP Configuration Protocol using GAS. Full
generation and processing of the configuration object is not included in
this commit.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add wpa_supplicant control interface commands for parsing the bootstrap
info URI from a QR Code (get peer public key) and to generate a new
bootstrap info with private key for local use. The optional
key=<hexdump> argument to the DPP_BOOTSTRAP_GEN command can be used to
specify the bootstrapping private key in OpenSSL ECPrivateKey DER
encoding format. This results in the local bootstrapping information
entry being created with the specified key instead of generating a new
random one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
There could be multiple pending TX operations and if the earlier ones
have used wait_time, but the last one did not, the driver call for
canceling pending wait was not done. This could result in the driver
getting stuck waiting for the previously scheduled wait time and not
being able to do new operations until that. Fix this by canceling the
wait if any of the past offchannel_send_action() calls since the last
offchannel_send_action_done() used non-zero wait_time.
This was showing up as issues in certain DPP Public Action frame
sequences when the same offchannel operation is used with multiple
frames and the last frame in the sequence does not need wait_time.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The additional SHA-384 and SHA-512 functionality is needed to support
DPP with various ECC curves.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can be helpful in figuring out what happened if P2P_FIND operation
is unexpectedly rejected.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_s->p2p_in_provisioning needs to be cleared when group formation
fully completes. The change to postpone GO side handling to the first
data connection in commit 41f853235f
('P2P: Extend group formation timeout on GO to first data connection')
resulted in making this not happen in one P2P Client side case: EAP-WSC
timeout in PBC case. While that is quite special case since it requires
30 second timeout without receiving new EAPOL frames and not getting
disassociation, it can apparently happen in some cases in practice. This
would result in new P2P operations (e.g., P2P_FIND) getting rejected
until wpa_supplicant is restarted.
Fix this by clearing wpa_s->p2p_in_provisioning whenever processing a
group formation failure case. For group formation success,
wpa_s->p2p_in_provisioning is left set to non-zero value to avoid
breaking the earlier limits on the GO side.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This allows the eap_proxy mechanism to be used with multiple SIMs by
following the configured sim_num to index which SIM to use for when
fetching the IMSI through eap_proxy.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This commit is similar to the commit
783c2920cc ('P2P: Check if the pref_freq
reported by the driver supports P2P') but extends the check for
supported pref_freq to wpas_p2p_select_go_freq().
This avoids issues with P2P_GROUP_ADD ending up selecting an unexpected
channel when get_pref_freq_list() (i.e.,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST) is used. Filter the
list by removing channels that do not allow P2P operation at all.
Previously, only the explicitly disallowed channels were removed and
that could have resulted in selecting an operating channel that is not
allowed for P2P and failing to complete the operation to start the
group.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add NULL checking for EAP name. If it is NULL, do not add the phase2
parameter autheap. This should not happen in practice due to earlier
checks for credential matching, but if there is a code path that would
allow this to be set, it is better to skip setting of the invalid value
and allow automatic selection of the Phase 2 parameters.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Change in any network configuration at runtime will cause flush to
PMKSA cache. For most of the network parameters if there is no change
in value, PMKSA flush is not performed except 'bssid' and 'priority'.
Add 'bssid_hint' to exemption list of avoiding PMKSA flush on change.
This is needed to complete change in commit
43a356b268 ('Provide option to configure
BSSID hint for a network').
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
This exposes user configurable option to set bssid_hint for a network.
bssid_hint indicates which BSS has been found a suitable candidate for
initial association for drivers that use driver/firmware-based BSS
selection. Unlike the bssid parameter, bssid_hint does not limit the
driver from selecting other BSSs in the ESS.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Addition of remove_ies() handled the CONFIG_IEEE80211R dependency, but
missed the caller being within CONFIG_FILS as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When reducing the configuration for MACsec/MKA to the bare minimum, so
no EAP authentication, just MACsec/MKA SA use with preshared key/name,
the EAPOL engine is still needed to run the protocol for MKA. Without
any EAP authentication options the IEEE8021X_EAPOL option is not set,
resulting in a non-working Key Agreement Entity.
Therefore the CONFIG_MACSEC block needs to move up and set the
IEEE8021X_EAPOL option.
Signed-off-by: Jaap Keuter <jaap.keuter@xs4all.nl>
In some practical cases, it is useful to suppress joining to node in the
distance. The new field mesh_rssi_threshold could be used as RSSI
threshold for joining.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This patch adds "TDLSCancelChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to disable channel switching
with a TDLS peer.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
This patch adds "TDLSChannelSwitch" dbus method on
"fi.w1.wpa_supplicant1.Interface" interface to enable channel switching
with a TDLS peer.
Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
Derive PMK-R0 and the relevant key names when using FILS authentication
for initial FT mobility domain association. Fill in the FT IEs in
(Re)Association Request frame for this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add support to set ignore assoc disallow to the driver so that the
driver ignores assoc disallowed bit set by APs while connecting. This is
used by drivers that handle BSS selection and roaming internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the driver provides input on MBO transition candidate handling, the
target value in get_mbo_transition_candidate() can be NULL if the driver
provided BSSID is not found in the wpa_supplicant BSS table. And later
it would be dereferenced. Fix this by adding an explicit check before
dereferencing the pointer.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
wpa_supplicant build with MBO enabled failed in CONFIG_WNM=y was not
specified explicitly. Add the WNM dependency automatically to avoid
needing explicit addition in build configuration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Commit 34f2851902 ('MBO: Parse MBO
ANQP-element on STA') started using the type variable outside
CONFIG_HS20 block, but forgot to remove the ifdef from the variable
declaration.
Signed-off-by: Jouni Malinen <j@w1.fi>
Disconnection due to DISABLE_NETWORK while being connected was resulting
in the AP getting blacklisted. Avoid this by setting own_disconnect_req
on a disconnect request due to DISABLE_NETWORK similarly to the
SELECT_NETWORK disconnection case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This adds a string "FILS_HLP_SENT" to connect event when HLP is sent
as part of ASSOC/CONNECT request.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
If the uuid configuration parameter is not set, wpa_supplicant generates
an UUID automatically to allow WPS operations to proceed. This was
previously always using an UUID generated from the MAC address. This
commit adds an option to use a random UUID instead. The type of the
automatically generated UUID is set with the auto_uuid parameter: 0 =
based on MAC address (default; old behavior), 1 = random UUID.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add a new PMKSA cache entry within wpa_supplicant if a driver event from
offloaded FILS shared key authentication indicates a new PMKSA entry was
created.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This keeps the internal ERP information within wpa_supplicant in sync
with the driver when offloading FILS shared key authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Update the internal fils_completed state when offloading FILS shared key
authentication to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add FILS/ERP parameters into the driver connect command to support FILS
shared key authentication offload.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was already done in sme_send_authentication() for the case where
wpa_supplicant SME is used. Similar change is needed for driver-SME to
allow FILS authentication to be offloaded to the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add support for setting and deleting PMKSA cache entries based on FILS Cache
Identifer. Also additionally add support for sending PMK as part of
SET_PMKSA to enable driver to derive keys in case of FILS shared key
offload using PMKSA caching.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When using FILS for FT initial mobility domain association, add MDE to
the Authentication frame from the STA to indicate this special case for
FILS authentication.
Signed-off-by: Jouni Malinen <j@w1.fi>
PMKSA_ADD and MESH_PMKSA_ADD command arguments include keying material,
so show it in debug log only if requested to do with the command line -K
argument.
Signed-off-by: Jouni Malinen <j@w1.fi>
In ap_scan=2 mode, wpa_supplicant_assoc_try() did not check whether the
SSID is temporarily disabled before trying to associate and this may
result in an infinite connect/disconnect loop. If the association
succeeds while the SSID is temporarily disabled, wpa_supplicant will
request to deauthenticate and that in turn will cause the SSID to be
temporarily disabled again. Fix that by postponing the association until
the SSID is no longer temporarily disabled.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Without CONFIG_P2P config, the following warning occurs if CONFIG_AP is
enabled for the build:
ap.c: In function ‘wpas_conf_ap_vht’:
ap.c:54:5: warning: unused variable ‘channel’ [-Wunused-variable]
u8 channel = conf->channel;
^
ap.c:53:5: warning: unused variable ‘center_chan’ [-Wunused-variable]
u8 center_chan = 0;
^
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This change fixes the following compilation warnings:
wnm_sta.c:1007:4: warning: implicit conversion from enumeration type
'enum mbo_transition_reason' to different enumeration type
'enum mbo_transition_reject_reason' [-Wenum-conversion]
The actual value of both MBO_TRANSITION_REASON_UNSPECIFIED and
MBO_TRANSITION_REJECT_REASON_UNSPECIFIED is 0, so this does not result
in any change in the contents of the frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, only the success and failure (to TX) cases were handled. It
is also possible for the driver to transmit the frame, but not receive
an ACK from the recipient. Address that by waiting for a short period of
time for a response. This fixes cases where OSU provider icon fetching
could get stuck if no ACK frame is received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Do not try to use FILS authentication unless the AP indicates support
for the type the local network profile enforces.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds an option to configure wpa_supplicant to use the perfect
forward secrecy option in FILS shared key authentication. A new build
option CONFIG_FILS_SK_PFS=y can be used to include this functionality. A
new runtime network profile parameter fils_dh_group is used to enable
this by specifying which DH group to use. For example, fils_dh_group=19
would use FILS SK PFS with a 256-bit random ECP group.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds STA side addition of OWE Diffie-Hellman Parameter element into
(Re)Association Request frame and processing it in (Re)Association
Response frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds AP side processing for OWE Diffie-Hellman Parameter element in
(Re)Association Request frame and adding it in (Re)Association Response
frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Since VHT can be toggled explicitly, also expose being able to disable
HT explicitly, without requiring HT overrides. Continue making it
default to enabled though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
