The duplicated WPS event in the parent interface should only be used
during P2P group formation, i.e., when the WPS operation was actually
started using the parent interface. When authorizing a client to
connect to an already running group, the WPS command is issued on
the group interface and there is no need to duplicate the event to
the parent interface.
This pointer is now used in number of places to check whether an
interface is in P2P Group Formation, so we better make sure it gets
cleared when group formation has been completed. This was done in
only some of the cases.
ap_setup_locked=2 can now be used to enable a special mode where
WPS ER can learn the current AP settings, but cannot change then.
In other words, the protocol is allowed to continue past M2, but
is stopped at M7 when AP is in this mode. WPS IE does not
advertise AP Setup Locked in this case to avoid interoperability
issues.
In wpa_supplicant, use ap_setup_locked=2 by default. Since the AP PIN
is disabled by default, this does not enable any new functionality
automatically. To allow the read-only ER to go through the protocol,
wps_ap_pin command needs to be used to enable the AP PIN.
The pending_invite_ssid_id of -1 (running group, not persistent) was
being stored incorrectly in the group interface, not device interface
(i.e., parent of the group interface) and consequently, the incorrect
information was used when processing the Invitation Response.
If there was a persistent group credentials stored with network id
0, those were used instead to try to set up a persistent group
instead of using the already running group.
Since the P2P peer entry may not have been available at the time the
join request was issued, we need to allow the P2P Interface Address
to be updated during join-scans when the P2P peer entry for the GO
may be added.
If the GO is not found, we cannot send Provisioning Discovery Request
frame and cannot really connect anyway. Since the Provisioning
Discovery is a mandatory part, it is better to continue join-scan
until the GO is found instead of moving to the next step where
normal connection scan is used (PD would not be used from there).
Use a limit of 10 scan attempts for p2p_connect join to avoid getting
in infinite loop trying to join. If the GO is not found with those
scans, indicate failure (P2P-GROUP-FORMATION-FAILURE) and stop the
join attempt.
CONFIG_WPA_CLI_EDIT=y can now be used to build wpa_cli with internal
implementation of line editing and history support. This can be used
as a replacement for CONFIG_READLINE=y.
Instead of using a separate process to receive and print event
messages, use a single-process design with eloop to simply
wpa_cli and interaction with readline.
Instead of multiple #ifdef blocks for readline within the function,
use two copies of the functions, one for readline, one without any
readline functionality.
When running "p2p_connect addr pbc join" command, send the
WPS-OVERLAP-DETECTED even also to the parent interface (i.e.,
the one on which the p2p_connect was issued) and not only the
group interface in case separate P2P group interfaces are used.
The driver wrapper may now indicate the preferred channel (e.g., based
on scan results) on both 2.4 GHz and 5 GHz bands (and an overall best
frequency). When setting up a GO, this preference information is used
to select the operating channel if configuration does not include
hardcoded channel. Similarly, this information can be used during
GO Negotiation to indicate preference for a specific channel based
on current channel conditions.
p2p_group_add command can now use special values (freq=2 and freq=5)
to indicate that the GO is to be started on the specified band.
wpa_supplicant_set_driver() is returning an error if the first driver
in the driver list is not built in. It should continue through the
driver list until it finds one that's built in.
If IEE8021X_EAPOL is not enabled in the config, wpa_drv_set_supp_port
must be called from the supplicant, otherwise port will not be
activated after association.
Commit d8d940b746 introduced a regression
that prevented TSN APs from being used with WEP since the AP was
rejected if it advertised WPA or RSN IE when we were configured to use
WEP. Resolve this by checking whether the AP is advertising a TSN, i.e.,
whether the AP allows WEP to be used as a group cipher. If so, allow
the AP to be selected if we are configured to use static WEP or
IEEE 802.1X (non-WPA).
It should be noted that this is still somewhat more restricted in AP
selection than earlier wpa_supplicant branches (0.7.x or older) that
ignore the WPA/RSN IE completely when configured for non-WPA.
The driver may end up leaving the current channel when we request
a new remain-on-channel and as such, it is better not assume we can
start new operations like sending an Action frame on the previous
off-channel.
If we have already asked the driver to start a new remain-on-channel,
we need to cancel it even if the actual remain-on-channel has not yet
started at the point when a new operation or timeout etc. triggers
Listen state to be stopped.
Even if p2p_scan_res_handler() returns 1 to indicate that scan result
iteration should be stopped, the p2p_scan_res_handled() needs to be
called to clear p2p_scan_running and to get a callback that will start
any operations that were delayed because of the running scan.
There is no need to separately move to the correct channel
for transmitting an Action frame that is using the group
interface (i.e., source address is P2P Interface Address).
This removes extra latency from P2P Action frame operations
within a P2P group.
This is an option to continue with wpa_supplicant and hostapd even if
config file has errors. The problem is that these daemons are the best
"candidates" for the config change, so if they can not start because
config file was let's say corrupted, you can not fix it easily.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This could have been using an uninitialized variable instead of
purposefully random value in picking up the channel. There is not
much of a difference for the use case here, but anyway, we may
as well do what was initially planned here and.
The destination address for p2p_serv_disc_resp must always be set
to an individual MAC address unlike p2p_serv_disc_req which may use
00:00:00:00:00:00 to indicate wildcard query. As such, we should not
try to check for this special case here.
The ieee80211_sta_free_hw_features() function is now used outside
the MLME code, so better make sure it gets included in the build
to avoid leaking memory.
Add a new driver event, EVENT_INTERFACE_UNAVAILABLE, for indicating
that the driver is not able to continue operating the virtual
interface in its current mode anymore, e.g., due to operating
channel for GO interface forced to a DFS channel by another virtual
interface.
When this happens for a P2P group interface, the P2P group will
be terminated and P2P-GROUP-REMOVED event shows the reason for
this as follows:
P2P-GROUP-REMOVED wlan0 GO reason=UNAVAILABLE
Replacing the BSSID with 'any' has never worked with wps_reg
command, so better not claim it could work. In addition, reject
this is wpa_supplicant to make it clearer that the operation
fails.
A new configuration parameter, p2p_group_idle, can now be used to set
idle timeout value for P2P groups in seconds (0 = no timeout). If set,
this values is used to remove P2P group (both GO and P2P client)
interfaces after the group has been idle (no clients/GO seen) for the
configuration duration.
The P2P-GROUP-REMOVED event is now indicating the reason for group
removal when known. For example:
P2P-GROUP-REMOVED wlan0 GO reason=REQUESTED
P2P-GROUP-REMOVED wlan1 client reason=IDLE
The driver wrapper may indicate EVENT_CHANNEL_LIST_CHANGED before
completing init(). This would likely result in segfault when driver
channel list is being read as part of processing this event when
P2P is enabled.
This command can be used to enroll a network based on a local
network configuration block instead of having to (re-)learn the
current AP settings with wps_er_learn.
This is not supposed to happen, but in theory, the GO may end up
changing its channels at some point. While it would be reasonable
to use one of the common channels, GO may be forced to use another
channel. The most likely reason for this would be if the P2P client
is enforcing only a single channel to be used (e.g., to avoid
multi-channel concurrent operations).
The P2P group component is now tracking of associated stations
in the group and the Group Limit bit in the Group Capabilities
is updated based on whether there is room for new clients in
the group.
This driver capability limit was supposed to indicate limit on
how many stations can associate with us in the AP mode, not how
many P2P peers are stored in the peer table.
The workaround to ignore no ctrl::ack received for GO Negotiation
Confirmation frame was only supposed to be used when the frame was
actually transmitted and just the ack was not received. However, due
to the way the driver failure on transmitting the frame were reported,
this ended up getting applied for all failures in sending the GO
Negotiation Confirmation frame.
Improve this by providing a mechanism to indicate whether send_action
operations fail locally before the frame was actually transmitted or
because of not receiving ack frame after having transmitted the frame.
This is needed to work around cases where the pending interface gets
removed, e.g., due to failed GO Negotiation. In such case, we may still
accept new GO Negotiation to be completed, but the interface did not
get created without a separate p2p_connect command.
The current implementation is not ideal since the re-created interface
may, at least in theory, get incorrect interface addrees. Though, this
would likely require that the driver supported more than one P2P group
interface and that the previous one was already taken into use for
another group.
This is a workaround for incorrect configuration (missing
virtual/physical identifier for config methods) for WPS 2.0 to
allow unmodified configuration from WPS 1.0 to be used while
enforcing compliant WPS 2.0 values.
The AP operation with wpa_supplicant requires an additional callback
to get the needed event information from hostapd side so that
wpa_msg() can be called for wpa_s->parent if needed.
This makes it easier to figure out what could have failed in the
WPS protocol and potentially provide more information for the
user on how to resolve the issue.
The driver wrapper can now indicate whether the driver supports
concurrent operations on multiple channels (e.g., infra STA connection
on 5 GHz channel 36 and P2P group on 2.4 GHz channel 1). If not,
P2P_CONNECT commands will be rejected if they would require
multi-channel concurrency.
The new failure codes for P2P_CONNECT:
FAIL-CHANNEL-UNAVAILABLE:
The requested/needed channel is not currently available (i.e., user has
an option of disconnecting another interface to make the channel
available).
FAIL-CHANNEL-UNSUPPORTED:
The request channel is not available for P2P.
Allow only the expected P2P Interface Address as the BSSID for
the AP to avoid selecting incorrect BSS should there be another
device that is advertising active PBC mode before the target
P2P GO does.
When the P2P state machine requests a remain- on-channel, there's a
potential race where it can then request a stop before the r-o-c has
actually started, in which case the stop will not be processed. Fix
that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new DBus API helper function wpas_dbus_error_unknown_error
function can be called as a result of a failure within internal
getter calls, which will call this function with a NULL message
parameter. However, dbus_message_new_error looks very unkindly
(i.e, abort()) on a NULL message, so in this case, we should not
call it.
I've observed this course of events during a call to
wpas_dbus_getter_bss_wpa with a faileld parse of the IE parameter.
We got here through a call to fill_dict_with_properties which
explicitly calls getters with a NULL message parameter. Judging
from the way it is called, this could easily occur if an AP sends
out a malformed (or mis-received) probe response. I usually run
into this problem while driving through San Francisco, so I'm
exposed to any number of base stations along this path.
This patch changes wpa_supplicant policy for handling '' in SSIDs field of
Interface.SSID DBus message. It treats '' (zero-length) SSID as a request
for a broadcast scan, instead of ignoring it.
This patch updates DBus API .Scan() logic per the test cases listed below:
1) Interface.Scan({'Type':'active', 'Channel':(2412, 20)})
Request: Active scan with only '' SSID (1 channel)
Should be: 1 broadcast ProbeRequest on specified channel
Previous: 1 broadcast ProbeRequest on specified channel
This Patch: 1 broadcast ProbeRequest on specified channel
2) Interface.Scan({'Type':'active', 'Channel':(2412, 20), 'SSIDs':['']})
Request: Active scan with only '' SSID (1 channel)
Should be: 1 broadcast ProbeRequest on specified channel
Previous: No ProbeRequests; passive scan results for specified channel
This Patch: FIXED: 1 broadcast ProbeRequest on specified channel
3) Interface.Scan({'Type':'active', 'Channel':(2412, 20), 'SSIDs':['MySSID']})
Request: Active scan with only non-'' SSIDs (1 channel)
Should be: 1 directed ProbeRequest for each SSID on specified channel,
no broadcast ProbeRequest
Previous: 1 directed ProbeRequest for each SSID on specified channel,
no broadcast ProbeRequest
This Patch: 1 directed ProbeRequest for each SSID on specified channel,
no broadcast ProbeRequest
4) Interface.Scan({'Type':'active', 'Channel':(2412, 20), 'SSIDs':['',
'MySSID']})
Request: Active scan with SSIDs, including 1 '' SSID (1 channel)
Should be: 1 broadcast ProbeRequest, 1 directed ProbeRequest for each
non-'' SSID on specified channel
Previous: 1 directed ProbeRequest for each non-'' SSID on specified
channel
This Patch: FIXED: 1 broadcast ProbeRequest, 1 directed ProbeRequest for
each non-'' SSID on specified channel
Currently the DBus Interface.Scan API is counter-intuitive. It issues
ProbeRequests when doing passive scans when channels are specified, and
does not issue ProbeRequests for broadcast active scans.
This patch updates DBus API .Scan() logic per the test cases listed below:
1) Interface.Scan({'Type':'passive'})
Request: Passive scan (all channels)
Should be: No ProbeRequests; Passive Scan results for all channels
Previous: 1 ProbeRequest on all channels for both broadcast SSID and
selected network (scan_ssid=1)
This Patch: --No change--: 1 ProbeRequest on all channels for both
broadcast SSID and selected network (scan_ssid=1)
2) Interface.Scan({'Type':'passive', 'Channel':(2412, 20)})
Request: Passive scan (1 channel)
Should be: No ProbeRequests; Passive Scan results for 1 channel
(plus overlapping channels)
Previous: 1 broadcast ProbeRequest on specified channel
This Patch: --Fixed--: No ProbeRequests; Passive Scan results for 1
channel (plus overlapping channels)
3) Interface.Scan({'Type':'active'})
Request: Active scan with no SSIDs (all channels)
Should be: 1 broadcast ProbeRequest on all channels
Previous: No ProbeRequests; passive scan results for all channels
This Patch: --Fixed--: 1 broadcast ProbeRequest on all channels
4) Interface.Scan({'Type':'active', 'Channel':(2412, 20)})
Request: Active scan with no SSIDs (1 channel)
Should be: 1 broadcast ProbeRequest on specified channel
Previous: No ProbeRequests; Passive scan results for specified
channel (plus overlapping channels)
This Patch: --Fixed--: 1 broadcast ProbeRequest on specified channel
The previous used .gitignore files were mathing some files that
were actually already in the repository (e.g.,
hostapd/logwatch/hostapd). Avoid this by listing the conflicting
entries in the root directory .gitignore with full path.
This cleans up debug log from unnecessary entries when using
wpa_cli/hostapd_cli or other ctrl_iface monitors that PING
periodically to check connectivity.
WPS 2.0 mandates the AP to include WPS IE in (Re)Association Response
if the matching (Re)Association Request included WPS IE. Provide the
needed WPS IE information to the driver_ops API for drivers that
process association frames internally.
Note: This modifies the driver_ops API by adding a new argument to
set_ap_wps_ie().
Instead of build time options (CONFIG_WPS_TESTING_EXTRA_CRED and
CONFIG_WPS_EXTENSIBILITY_TESTING), use a single build option
(CONFIG_WPS_TESTING) and runtime configuration of which testing
operations are enabled. This allows a single binary to be used
for various tests.
The runtime configuration can be done through control interface
with wpa_cli/hostapd_cli commands:
Enable extensibility tests:
set wps_version_number 0x57
Disable extensibility tests (WPS2 build):
set wps_version_number 0x20
Enable extra credential tests:
set wps_testing_dummy_cred 1
Disable extra credential tests:
set wps_testing_dummy_cred 0
Previously, wpa_supplicant remaining in scanning state without
trying to connect, but there is no particular need to do that.
Instead, cancel WPS operation completely whenever PBC session
overlap is detected.
Disconnection event may be received while in associating state.
Previously, wpa_supplicant could get stuck not trying to reconnect
in that case at least with nl80211. Allow scan request in this
state to avoid the issue. This helps especially with APs that do
load balancing by sending Deauthentication frame as a response to
Reassociation Request frame after successful Authentication frame
exchange.
ctrl_interface STA_AUTOCONNECT command can now be used to disable
automatic reconnection on receiving disconnection event. The default
behavior is for wpa_supplicant to try to reconnect automatically, i.e.,
to maintain previous behavior.
The overlap condition cannot disappear before group formation timeout
hits, so there is no point in continuing in this case and failure can
be indicated immediately.
This allows the pending group interface to be removed if we fail
to join a running group. A longer than 15 second timeout is needed
here since the GO may not have authorized our connection yet.
A new ctrl_interface command, WPS_CANCEL, can now be used to cancel
a pending or ongoing WPS operation. For now, this is only available
with wpa_supplicant (either in station or AP mode). Similar
functionality should be added for hostapd, too.
The scan operation before Provision Discovery Request may not include
the GO. However, we are likely to have the GO in our P2P peer table,
so use that information to figure out the operating channel if BSS
table entry is not available.
This is needed to make sure we do not try to accidentally enable GO
in channels that may not be allowed. In addition, this may help with
some driver that do not like channel 14 even as a passive scan
channel.
This command is supposed to return the PIN value that was generated
or passed in as an argument. In the AP case, the entered PIN was not
being returned.
This is needed to be able to change parameters for dynamically
created interfaces between the creation of the interface and
association/start AP commands.
Following ctrl_interface commands can now be used:
P2P_SET client_apsd disable
- disable configuration (i.e., use driver default) in client mode
P2P_SET client_apsd <BE>,<BK>,<VI>,<VO>;<max SP Length>
- enable UASPD with specific trigger configuration (0/1) per AC
(max SP Length is currently ignored)
P2P_SET go_apsd disable
- disable configuration (i.e., use driver default) in AP mode
P2P_SET go_apsd <0/1>
- disable/enable APSD in AP mode
This event indicates the Device Password ID that the peer tried
to use in GO Negotiation. For example:
P2P-GO-NEG-REQUEST 02:40:61:c2:f3:b7 dev_passwd_id=4
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
For now, this applies to the test command that can be used to set
periodic NoA (p2p_set noa). The value are stored and periodic NoA
is enabled whenever there are no non-P2P STAs connected to the GO.
While this is not strictly speaking required by the P2P specification
for a not-P2P Managed Device, this can provide useful information for
the P2P manager AP and may be needed to pass certification tests.
For client-invites-device case, the pre-authorization of an invitation
to running group will need to allow Invitation Request from specified
address, too. This is for testing uses only.
"wpa_cli p2p_set peer_filter <MAC address>" can now be used to
only allow a single P2P Device (based on P2P Device Address) to be
discovered for testing. Setting the address to 00:00:00:00:00:00
disables the filter.
This is mainly designed for testing and allows p2p_connect join auth
to be used to accept a specific invitation to an active group that
may be received in the future.
The driver event for remain-on-channel may be delayed in a way that
allows management-frame-received event to be received before
wpa_supplicant knows that the driver is actually already on the
previously requested channel. We should not request a new
remain-on-channel to send a response to just a frame if we are waiting
for the driver to get to the same channel. Instead, just continue
waiting for the driver event.
When the first wpa_supplicant interface is not the correct one for
transmitting an Action frame (e.g., P2P Presence Request frame
uses a group interface), the code got stuck in an infinite busy
loop. Fix the iteration to go through the interfaces properly.
If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
Verify that the driver wrapper is using a valid deauth/disassoc
event before dereferencing the addr pointer. The address is required
to be set in AP mode, but it is safer to verify this here than to
trust on all driver wrappers doing the correct thing.
Some NDIS drivers require a workaround to allow them to associate
with a WPS AP that is already using protection (Privacy field = 1).
Let driver_ndis.c know if the AP is already using Privacy and if so,
configure a dummy WEP key to force the driver to associate.
Commit d8d940b746 broke the logic on
iterating through all configured network blocks. This was supposed
to continue the loop on mismatch to allow other than the first
configured network to be found.
This patch adds support for wired IEEE 802.1X client on the Solaris.
I have tested with these:
OS : OpenSolaris 2009.06
EAP : EAP-MD5
Switch : Cisco Catalyst 2950
The driver is likely to indicate an immediate signal event when the
threshold value is configured. Since we do this immediately after
association, there is not much point in requesting a new scan to be
started based on this event.
The driver is likely to indicate an immediate signal event when the
threshold value is configured. Since we do this immediately after
association, there is not much point in requesting a new scan to be
started based on this event.
This removes quite a bit of duplicated code and allows network block
priority configuration to be used to prefer unprotected networks and
also allows use on open network with good signal strength even if
scan results show a protected network with marginal signal strength
that does not allow it to be used.
The wpa_supplicant compilation without CONFIG_WPS option results in
messages below.
scan.c: In function 'wpa_supplicant_scan':
scan.c:246: warning: unused variable 'wps'
This trivial patch erases this warning.
This clears up authentication state in the driver and in case of
cfg80211, unlocks the BSS entry for the previously used AP. The
previous commit cf4783e35f changed
only the ctrl_iface DISCONNECT command behavior; this new commit
does the same for D-Bus commands.
wpa_s->bssid is already cleared by mark_disassoc() when we're getting the
disassociation event for the case where wpa_supplicant requested
disassociation. wpa_s->sme.prev_bssid holds the BSSID we need to check
for, so use that instead.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When passing several authentication algorithms through auth_alg, we
should try all of them when the first one fails. The wext driver goes
through the connect nl80211 command and the retries are then handled by
the kernel. The nl80211 doesn't and we have to handle that from
userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is needed to avoid trying to reassociate based on new scan
results when using wpa_supplicant to control AP mode. This could
happen if something external triggered the driver to run a scan.
When SME is in wpa_supplicant (mac80211), we need to make sure that
the kernel code has valid BSS entry for the AP. In some cases it
seemed to be possible to end up not having current information in
cfg80211 or mac80211 which can result to association failures. Avoid
this by always running through the scan request before initial
connection attempt.
It is possible that l2_packet is not used with wpa_supplicant
in some cases, so better make sure we do not end up notifying
l2_packet code about authentications unless it was actually
initialized in the first place.
Store list of all discovered BSSes in the ESS and on which frequencies
they have been seen. Use this information to dynamically generated the
list of channels for background scans.
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
Addition of the background scanning mechanism in commit
60b94c9819 moved the scan trigger
into a new function that was also incrementing the scan_runs
counter, but the removal of the previous scan_runs incrementation
was forgotten from that patch. This counter should only be updated
into a single location, so remove the old one. This improves AP
selection for WPS provisioning by not skipping some of the initial
scans.
wps_er_config can now be used to configure an AP. It is similar to
wps_er_learn, but instead of only learning the current AP settings,
it continues to send M8 with the new settings for the AP.
wps_er_start command now takes an optional parameter that can be used
to configure a filter to only allow UPnP SSDP messages from the
specified IP address. In practice, this limits the WPS ER operations
to a single AP and filters out all other devices in the network.
This avoids an invalid D-Bus call during interface initialization.
The wpa_state change can happen before the D-Bus interface is set up,
so we must be preparted to handle this early event signal. In theory,
it should be possible to reorder initialization code to make sure
D-Bus signals are ready, but that would likely require quite a bit of
code restructuring, so it looks like a safer option for now is to just
skip the early event.
The wpa_supplicant compilation with CONFIG_AP option and without
CONFIG_IEEE80211R, CONFIG_WPS, NEED_SME, CONFIG_CLIENT_MLME options
results in following messages.
../src/ap/drv_callbacks.o: In function `hostapd_notif_assoc':
../src/ap/drv_callbacks.c:59: undefined reference to
`ieee802_11_parse_elems'
gmake: *** [wpa_supplicant] Error 1
Add a new wpa_supplicant state: interface disabled. This can be used
to allow wpa_supplicant to be running with the network interface even
when the driver does not actually allow any radio operations (e.g.,
due to rfkill).
Allow driver_nl80211.c and driver_wext.c to start while rfkill is in
blocked state (i.e., when ifconfig up fails) and process rfkill
events to block/unblock WLAN.
Use regular expression matches to see if input is not the (now translated?)
string "Select any network" and is a "<network id>: <ssid>" string or the
"all" keyword where that is applicable.
Signed-off-by: Kel Modderman <kel@otaku42.de>
This allows wpa_supplicant to be started quickly with an empty
configuration. If an external program wants to fetch scan results
from wpa_supplicant, it will need to request a scan explicitly
in this type of case.
Add "wpa-ft-psk", "wpa-psk-sha256", "wpa-ft-eap" and "wpa-eap-sha256"
possible KeyMgmt values of interface capabilities to fit values in
BSS RSN options dictionary.
This adds more details into the CTRL-EVENT-DISCONNECTED event to
make it easier to figure out which network was disconnected in some
race conditions and to what could have been the reason for
disconnection. The reason code is currently only available with
the nl80211 driver wrapper.
These bursts can result in control interface monitors being detached
even if the external program is still working properly. Use much larger
error threshold for ENOBUFS to avoid this.
There is no absolute requirement for separating address allocation
into separate functions, so simplify the driver wrapper interface
to use just if_add and if_remove instead of adding the new
alloc_interface_addr() and release_interface_addr() functions.
if_add() can now indicate if the driver forced a different interface
name or address on the virtual interface.
Scan only the frequency that was used during provisioning during the
first five scans for the connection. This speeds up connection in the
most likely case where the AP remains on the same channel. If the AP is
not found after these initial scans, all channels will be scanned.
'wpa_cli roam <bssid>' can now be used to test roaming within an ESS
(e.g., for FT over-the-air). This command will bypass a new scan and
will select the BSS based on the specified BSSID. It is responsibility
of the caller to make sure that the target AP is in the BSS table.
This can be done, e.g., by running a scan before the roam command,
if needed.
Instead of parsing the IEs in the callers, use the already existing
parser in wpa_ft.c to handle MDIE and FTIE from initial MD association
response. In addition, this provides more complete access to association
response IEs to FT code which will be needed to fix FT 4-way handshake
message 2/4.
This sets the FT Capability and Policy field in the MDIE to the values
received from the target AP (if available). This fixes the MDIE contents
during FT Protocol, but the correct value may not yet be used in initial
mobility domain association.
When using wpa_supplicant SME (i.e., using nl80211), the rsn_supp
module was not informed of the WPA/RSN IE that was used in
(Re)Association Request frame. This broke roaming between APs that
use different security policy (e.g., changing between WPA/TKIP and
WPA2/CCMP APs) or when using PMKSA caching.
This allows bgscan modules to use more information to decide on when
to perform background scans. bgscan_simple can now change between
short and long background scan intervals based on signal strength
and in addition, it can trigger immediate scans when the signal
strength is detected to be dropping.
bgscan_simple takes following parameters now:
short interval:signal strength threshold:long interval
For example:
bgscan="simple:30:-45:300"
This can be used to limit which frequencies are considered when
selecting a BSS. This is somewhat similar to scan_freq, but will
also affect any scan results regardless of which program triggered
the scan.
Need to kill the monitor process before running detach command on
the monitor connection to avoid race where the monitor process may
end up getting the detach command result.
Previously, this was only done with userspace MLME (i.e., driver_test.c);
now, driver_nl80211.c can deliver the FT Action Response (FT-over-DS)
for processing. The reassociation after successful FT Action frame
exchange is not yet implemented.
Despite comments in the wpa_config_update_prio_list(struct wpa_config
*config) telling that it is called "if priority for a network is
changed", it is apparently not.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
This patch allows wpa_supplicant to compile on Debian's kfreebsd
architectures.
Patch by Stefan Lippers-Hollmann based on work done by Petr Salinger
and Emmanuel Bouthenot for 0.6.X (http://bugs.debian.org/480572).
filter_ssids=1 global configuration parameter can now be used to
enable scan result filtering (with -Dnl80211 only for now) based on
the configured SSIDs. In other words, only the scan results that have
an SSID matching with one of the configured networks are included in the
BSS table. This can be used to reduce memory needs in environments that
have huge number of APs.
New global configuration parameter bss_max_count can now be used to
change the maximum BSS table size. The old fixed size limit (200) is
used as the default value for this parameter.
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
This is needed to allow the BSS table entry for the previously used
BSS to be removed. Now wpa_bss_in_use() can return 0 for the last BSS
that was used as soon as deauthentication/disassociation event has been
received.
Some drivers may need to use a specific ifname for the virtual
interface, so allow them to do this with a new parameter passed
to the alloc_interface_addr() handler.
CFLAGS += -DCONFIG_WPA_CLI_FORK=y in .config can be used to
configure wpa_cli build to make a version of wpa_cli that forks
a child process to receive event messages. This allows the events
to be shown immediately instead of having to wait for the next
periodic poll with PING.
This allows external programs (e.g., UI) to get more information
about server certificate chain used during TLS handshake. This can
be used both to automatically probe the authentication server to
figure out most likely network configuration and to get information
about reasons for failed authentications.
The follow new control interface events are used for this:
CTRL-EVENT-EAP-PEER-CERT
CTRL-EVENT-EAP-TLS-CERT-ERROR
In addition, there is now an option for matching the server certificate
instead of the full certificate chain for cases where a trusted CA is
not configured or even known. This can be used, e.g., by first probing
the network and learning the server certificate hash based on the new
events and then adding a network configuration with the server
certificate hash after user have accepted it. Future connections will
then be allowed as long as the same server certificate is used.
Authentication server probing can be done, e.g., with following
configuration options:
eap=TTLS PEAP TLS
identity=""
ca_cert="probe://"
Example set of control events for this:
CTRL-EVENT-EAP-STARTED EAP authentication started
CTRL-EVENT-EAP-PROPOSED-METHOD vendor=0 method=21
CTRL-EVENT-EAP-METHOD EAP vendor 0 method 21 (TTLS) selected
CTRL-EVENT-EAP-PEER-CERT depth=0 subject='/C=US/ST=California/L=San Francisco/CN=Server/emailAddress=server@kir.nu' hash=5a1bc1296205e6fdbe3979728efe3920798885c1c4590b5f90f43222d239ca6a
CTRL-EVENT-EAP-TLS-CERT-ERROR reason=8 depth=0 subject='/C=US/ST=California/L=San Francisco/CN=Server/emailAddress=server@kir.nu' err='Server certificate chain probe'
CTRL-EVENT-EAP-FAILURE EAP authentication failed
Server certificate matching is configured with ca_cert, e.g.:
ca_cert="hash://server/sha256/5a1bc1296205e6fdbe3979728efe3920798885c1c4590b5f90f43222d239ca6a"
This functionality is currently available only with OpenSSL. Other
TLS libraries (including internal implementation) may be added in
the future.
When multiple APs are present in scan results with similar signal
strength, wpa_supplicant may end up bounching between them frequently
whenever new scan results are available (e.g., due to periodic scans
requested by NetworkManager). This can result in unnecessary roaming
and in case of the current cfg80211 version, to frequent network
disconnections.
Do not request a roam if the current BSS is still present in the scan
results and the selected BSS is in the same ESS and has only a slighly
stronger signal strength.
Expose RSN and WPA properties for BSS objects containing information
about key management and cipher suites. Get rid of WPA/RSN/WPSIE
byte array properties and add IEs byte array property with all IE data
instead.
This allows the driver wrappers to return two sets of IEs, so that
the BSS code can use information from both Beacon and Probe Response
frames if needed. For example, some Cisco APs seem to include more
information in Wireless Provisioning Services IE when it is in the
Beacon frame.
idx == 0 should be enough to make sure that the addr is set, but
verify that this is indeed the case to avoid any potential issues if
auth_set_key() gets called incorrectly.
There was an extra semicolon that broke the calculation of registered
properties and resulted in obj_desc->prop_changed_flags not being
allocated long enough for all the flags.
The path pointer used as the timeout_ctx was not constant; the path
string itself may have been the same, but the pointer certainly was not
since it was sometimes from stack and sometimes from the dynamically
allocated buffer in obj_desc. This caused some of the eloop timeout
cancellations not to find the timeout. Fix this by using the obj_desc
as the timeout context data.
Instead of sending PropertiesChanged signals for each changed
property separately, mark properties as changed and send aggregated
PropertiesChanged signals for each interface in each object.
Aggregated PropertiesChanged signal is sent
- for all object after responding on DBus call
- for specified object after manual call to
wpa_dbus_flush_object_changed_properties() function
- for each object separately after short timeout (currently 5 ms)
which starts when first property in object is marked changed
The actual supplicant state is exposed via a property on the interface
object. So having a separate signal StateChanged for notifying about
changes is a bad idea. The standard PropertiesChanged signal should be
used for this.
The advantage of StateChanged signal was that it includes the previous
state, but not even NetworkManager is making use of this. And tracking
the old state via the property and this signal is easily possible anyway.
Instead of using some magic integer values that really only mean
something to WPA internal code, just use simple strings. Possible
values are "msgdump", "debug", "info", "warning" and "error" which
map directly to WPA debugging support.
The three existing enums were already depending on using the same
values in couple of places and it is just simpler to standardize on
one of these to avoid need for mapping between different enums for
the exact same thing.
Most of this file was already moved into wpa_supplicant/scan.c and
we can remove the file completely by having couple of small helper
functions copied to the remaining users outside core wpa_supplicant
code.
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
This adds new commands and events for allowing off-channel Action
frame exchanges to be requested. This functionality is not yet used
and is only fully supported by driver_test.c at this point.
driver_nl80211.c has support for the remain-on-channel commands, but
the Action frame TX/RX part is still pending review for the kernel
code and as such, is not yet included here.
This adds placeholder code for allowing the virtual interfaces to be
pre-allocated a MAC address before the interface type is known with
drivers that do not handle interface type changes.
Get rid of wpa_supplicant_sta_rx() and add a new driver event that is
marked to be used only with driver_test.c. In addition, remove this
functionality from privsep wrapper. This is only use for client mode
MLME testing with driver_test.c.
The wpa_s->bss_id list was being corrupted when the BSS entry needed
to be reallocated due to longer IE data. The entry has to be removed
from all lists before reallocation to avoid this (it was only removed
from the wpa_s->bss list).
There is no need to duplicate the method/signal/property arrays that
were registered for objects. The registration was using static arrays
on methods/signals/properties in all places and we can as well use
those throughout without having to allocate memory and copy all the
entries for every object. This reduces number of allocations and
amount of unnecessary code quite a bit.
Get more information about scans when updating BSS table information.
This allows the missing-from-scans expiration rule to work properly
when only partial set of channels or SSIDs are being scanned.
The perror() calls do not make much sense with libdbus functions and
wpa_printf() would really be used for all error printing anyway. In
addition, many of the error messages on out-of-memory cases are not
really of much use, so they were removed. This is also cleaning up
some of the error path handling to avoid duplicated code.
These cannot be NULL, so there is no point in checking for that. In
addition, the accessor function for this is just making the code harder
to understand.
This callback structure was specific to the new D-Bus API which makes
it more or less pointless. It is just simpler to call the notification
functions directly. More proper design could be to use a generic
mechanism for registering notification callbacks into notify.c, but
that is not yet available and should not be designed just based on a
single user.
These header files are included outside the dbus subdirectory and there
is not really any need to force the libdbus dbus/dbus.h header file to
be included into these files.
There is no need to go through methods, signals, and properties in
two loops and only collect interfaces in the first run. Get rid of
unnecessary CPU use by generating the XML data for interfaces with
a single pass.
The XML used in D-Bus introspection is simple and there is no need to use
libxml2 to generate it. This gets rid of the dependency on the large
library by using internal XML generation.
Simpler to use for loops instead of handling next pointer selection
in all places. In addition, couple of functions could have ended up
in an infinite loop on error path since the pointer update was missed.
In addition, remove Quality and Noise properties since the BSS table
is not the correct place for fetching per-channel information (Noise)
and Quality is not well-defined (nor available from many drivers).
We don't actually need to define separate user_data argument for
each method handler and property getter/setter. Instead, we can define
one argument for the whole object. That will make it easier to register
objects like BSS or Networks which require allocating and freeing
memory for their arguments.
This was mostly identical code that had been copied for the new D-Bus
API implementation and as such, should really have been shared from
the beginning. In addition, the copied code ended up generating
interesting stack traces since the actual D-Bus connection was being
shared even though the pointer to it was stored in two distinct
data structures. The old D-Bus code ended up dispatching some
D-Bus callbacks which ended up running the new D-Bus code.
Since the private context pointers were mostly identical, everything
seemed to more or less work, but this design was just making things
more complex and potentially very easy to break.
Do not try to unregister BSS objects twice (the latter one with invalid
path) and make sure all network objects get added and removed properly
(the ones read from configuration file were not being registered, but
were tried to be unregistered).
This will allow more cleanup to be done for scan results processing
since all code can now be made to depend on the BSS table instead of
the temporary scan results.
Once remaining code has been converted to use the BSS table, the new
scan results can be freed immediately after the BSS table has been
updated. In addition, filtering of BSS information should be added
to better support systems with limited resources. For now, memory
use can be limited by defining WPA_BSS_MAX_COUNT to be smaller.
Anyway, better filtering of results to only the configured networks
should be added to improve this.
Replace the scan results -based implementation with the use of information
from the new BSS table maintained by wpa_supplicant to get a more stable
source of BSS data. Change the use of BSSID as the key for the BSS object
to use the BSS table unique identifier so that multi-SSID APs can be
handled properly.
In addition, provide another option for iterating through the BSS
entries. The old iteration: "BSS 0", "BSS 1", .. with index number.
The new iteration: "BSS FIRST", "BSS NEXT-<prev id>", .. with id
fetched from the previous output (id=<id> line).
This allows the BSS list to be iterated in order of increasing id
to avoid problems with new scans reordering entries. The order on the
wpa_s->bss list changes with most recently updated entries being moved
to the tail of the list while wpa_s->bss_id list maintains its order
with new entries being added to the tail and old entries being removed
when they expire.
This allows the driver interface to be deinitialized before
struct hostapd_data instance gets freed. This needs to be done so
that the driver wrapper does not maintain a context pointer to
freed memory.
Collect information from scan results into a BSS table that will not
expire information as quickly as scan results where every new scan,
no matter for how limited set of channels/SSIDs, clears all old
information.
For now, this is only used for D-Bus BSS added/removed notifications,
but this will likely be extended to be used internally instead of the
scan results to better support partial scans.
This has example code for fetching and interface object and optionally
creating a new interface is one is not found. After that, a scan is
requested and the script continues to listed for signals from
wpa_supplicant and print information about scan results and state
changes.
Must initialize key to be NULL since it can be used in an error
message. If the Scan method did not actually include any dict entries,
the uninitialized pointer was used and this could result in
wpa_supplicant crashing.
Removed the hack that used typecast to get rid of const by using local
variables that are allocated and freed. Fix couple of memory leaks
and check that the required Ifname parameter is included.
Doxygen and some build tools may get a bit confused about same file
name being used in different directories. Clean this up a bit by
renaming some of the duplicated file names in src/ap.
Initialize struct hostapd_data driver context with the same driver
information that was initialized earlier during wpa_supplicant start.
This allows the AP mode operations to be completed directly with the
same calls in AP code without having to maintain a separate translation
layer between the AP and station mode driver context.
This code can be shared by both hostapd and wpa_supplicant and this
is an initial step in getting the generic code moved to be under the
src directories. Couple of generic files still remain under the
hostapd directory due to direct dependencies to files there. Once the
dependencies have been removed, they will also be moved to the src/ap
directory to allow wpa_supplicant to be built without requiring anything
from the hostapd directory.
It would be bettet to avoid including driver_i.h, i.e., direct driver
operation calls from hostapd components. This is an initial step in
that direction for WPS IE updates.
This mode allows associated stations to use 4-address frames to allow
layer 2 bridging to be used. At least for the time being, this is only
supported with driver=nl80211.
This adds config_methods configuration option for wpa_supplicant
following the design used in hostapd. In addition, the string is
now parsed in common code from src/wps/wps_common.c and the list
of configurable methods include all the defined methods from
WPS 1.0h spec.
The D-Bus interface does not really have anything to do with the
wpa_supplicant ctrl_iface interface and as such, this prefix in
dbus files is both confusing and unnecessarily. Make the file names
shorter by removing this prefix.
Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
WPA_TRACE=y builds will now verify that memory allocation in done
consistently using os_{zalloc,malloc,realloc,strdup,free} (i.e., no
mixing of os_* functions and unwrapper functions). In addition, some
common memory allocation issues (double-free, memory leaks, etc.) are
detected automatically.
WPA_TRACE=y can now be used to enable internal backtrace support that
will provide more details about implementation errors, e.g., when some
resources are not released correctly. In addition, this will print out
a backtrace automatically if SIGSEGV is received.
When setting up an AP with wpa_supplicant, the initial connection was
not necessarily setting oper state from DORMANT to UP which would be
blocking normal data frames. Fix this by initializing new_connection
to 1 so that even the first change to COMPLETED state will end up
setting oper state.
Replace driver wrapper calls to hostapd_tx_status(),
hostapd_rx_from_unknown_sta(), hostapd_mgmt_rx(), and
hostapd_mgmt_tx_cb() with new generic driver events
EVENT_TX_STATUS, EVENT_RX_FROM_UNKNOWN, and EVENT_RX_MGMT.
This cleans up lot of the driver wrapper code to be less dependent
on whether it is being used within wpa_supplicant AP mode or hostapd.
The Prism54.org project seems have been dead for a while and it does not
look like this driver would ever be maintained again. Furthermore, it is
difficult to find a version that would work with the driver_prism54.c
wrapper and there is another driver for these card in the Linux kernel
tree.
The hostapd integration in driver_prism54.c is quite different from the
other driver wrappers and would require major effort to get it cleaned
up. Since there does not seem to be any real users for the cleaned up
version, there does not seem to be justification to spend this effort on
the wrapper. This old code is making it much more difficult to clean up
the driver interface and at this point, the best option seems to be to
remove the driver wrappers. Should someone really still need this, the
old code will continue to be available in hostapd 0.6.x.
Instead of using the latest selected registrar change, collect selected
registrar information separately from all registrars and use the union
of this information when building the WPS IE for Beacon and Probe
Response frames.
Note: SetSelectedRegistrar UPnP action does not include a unique
identifier, so the ER matching routine is based only on the IP address
of the ER. In theory, there could be multiple ERs using the same IP
address (but different port or URL), so there may be some corner cases
that would not always match the correct ER entry at the AP. Anyway, this
is not really expected to occur in normal use cases and even if it did
happen, the selected registrar information is not any worse than it was
before when only the last change from any registrar for being
advertized.
In addition to the bitrate, the only other variable in this structure
is used internally in hostapd. Move this structure into hostapd.h and
make the driver API use simpler data structure (array of bitrates).
The following defines are not really needed in most places, so
remove them to clean up source code and build scripts:
EAP_TLS_FUNCS
EAP_TLS_OPENSSL
EAP_TLS_GNUTLS
CONFIG_TLS_INTERNAL
Wait for connection (IBSS join completed) event before marking state
completed. In addition, do not use the station mode authentication
timeout since that can trigger full disconnection from IBSS when
there is a timeout with just one of the peers.
Initialize the new DBus API before the old one, so new applications
which can use both, the old and the new API will be notified first
that new API is available.
cfg80211/mac80211 can get into somewhat confused state if the AP only
disassociates us and leaves us in authenticated state. For now, force
the state to be cleared with deauthentication to avoid confusing errors
if we try to associate with the AP again. This gets rid of 30 second
delay (scan timeout) in cases where only a disassociation frame is
received from the AP.
8a5ab9f5e5 fixed global driver context
for init2(), but it also broke driver initialization with driver
wrappers that do not use init2().. Fix this by setting wpa_s->global
before it gets dereferenced.
In addition, start ordering header file includes to be in more
consistent order: system header files, src/utils, src/*, same
directory as the *.c file.
This makes it clearer which files are including header from src/common.
Some of these cases should probably be cleaned up in the future not to
do that.
In addition, src/common/nl80211_copy.h and wireless_copy.h were moved
into src/drivers since they are only used by driver wrappers and do not
need to live in src/common.
This avoids passing the raw scan results into the RSN code and by
doing so, removes the only dependency on src/drivers from the
src/rsn_supp code (or from any src subdirectory for that matter).
Use shared functions for converting Primary Device Type between binary
and string formats. In addition, use array of eight octets instead of a
specific structure with multiple fields to reduce code complexity.
This gets rid of previously deprecated driver_ops handlers set_wpa,
set_drop_unencrypted, set_auth_alg, set_mode. The same functionality
can be achieved by using the init/deinit/associate handlers.
These driver wrappers should not be used anymore; WEXT should be used
instead. However, there may still be users stuck on older kernel versions
that may require driver specific wrappers, so the source code still
remains in the repository.
Clean up driver interface by merging hostapd and wpa_supplicant
specific set_beacon driver_ops into a single one. In addition,
merge set_beacon_int into to the same operation.
This removes many of the cases where moving to the WPS tab can be
undesired. It is really only useful if we are not currently connected
and there is an AP available that would likely be able to provide us
network connectivity with use of WPS (active PBC more or selected
registrar set).
Clean up the peer dialog information to be more user friendly. Only
show the device type in the tooltip and move the verbose details into
a separate area in a new Properties dialog. The new dialog will also
show some of the standard fields with titles to make them easier to
read.
The Enrollee entry may be deleted while the PIN query dialog is open.
To avoid crashing on using freed entry, copy the needed data into
local variables before and use the local data after the PIN dialog
has been closed.
The peer entries are now using different icons based on their type. As
a starting point, a separate AP and laptop icons are used. More icons may
be added in the future to mark different device types (e.g., based on
primary device type information from WPS).
When using umask 0077, the control interface directory was left without
group read/execute permissions even if the configuration file explicitly
asked for the group to be allowed to access the control interface. Fix
this by adding read/execute permissions for group if a specific group is
defined in the configuration. [Bug 199]
Change the dbus policy file to only allow root applications to receive
signals from wpa_supplicant. This keeps WPS Credentials data secret
from non-root listeners.
When trying to build wpa_gui (Qt4 version) from openembedded it fails
because Qt4 is compiled without session manager and thus wpa_gui fails
to compile.
I attached a patch, that enables compiling without Session Manager (via
preprocessor) if it is not compiled into Qt4; otherwise, it behaves as
it does right now.
I checked to build on my host (Debian unstable, Session Manager
enabled) and openembedded (Session Manager disabled).
This will need some additional code in wps_er_pbc() to handle PBC mode
enabling for a single AP only. For now, this can only be expected to work
when the ER is connected to a single AP.
Clean up registration of large number of dbus method/property/signal
handlers by using arrays containing all the information needed to call
the registration functions.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
Smartcard parameter update via DBus ended up re-initializing the EAPOL
state machine without updating the pointer inside WPA state machine.
This can trigger a segfault when EAP layer attempts to use the old
reference. Fix this by re-initializing the pointer inside WPA state
machine.
Better make sure we do not end up writing over the end of the local
registered_sig buffer regardless of how many arguments are used in
dbus method description.
There is no point checking whether wpa_s is not NULL after having
dereferenced it earlier in the function.. Furthermore, there is no
need to use a local variable for wpas_dbus_get_path() result.
The cleanup routine in the end would have dereferenced props pointer
which could be NULL. There is no need to go through that cleanup code
in this case, so just exit from the function with return instead.
ssid could be NULL here at least based on the function documentation,
so better check whether that is the case prior to calling the
notification function.
Commit d3a9822542 broke per-SSID scan
by using the ssid variable for internal loop and by doing so,
overriding the value that was needed below to figure out whether the
scan is for a specific SSID. Fix this by using a temporary variable
instead when looping over network finding which frequencies to scan for.
This was triggering some gcc versions to warn about strict aliasing.
Since the typecast is not really needed here, the cleanest way to get
rid of the warnings is to just use the correct type for the local
variable.
This is like wpa_msg(), but the output is directed only to
ctrl_interface listeners. In other words, the output will not be
shown on stdout or in syslog.
Change scan result reporting to use wpa_msg_ctrl() for
CTRL-EVENT-SCAN-RESULTS message at info level and wpa_printf() at
debug level to avoid showing scan result events in syslog in the
common configuration used with NetworkManager.
This patch implements the new DBus API. Both, the new and the
previous API may work concurrently and may be turned on or off
separately in .config file.
Some features of the new API are:
- more wpa_supplicant's events are signaled with DBus signals,
- introspection data (requires libxml2 and may be disabled),
- CurrentBSS and CurrentNetwork properties,
- PropertyChanged signal for most of properties,
- Relatively easy to extend.
.config options for the new API are: CONFIG_CTRL_IFACE_DBUS_NEW=y and
CONFIG_CTRL_IFACE_DBUS_INTRO=y for introspection.
This commit misses couple of parts from the full implementation
(these are still under review):
- fetching all configuration parameters for learning WPS information
- scan result BSS add/remove notification (register_bss() and
unregister_bss() notification callbacks)
Clean up code so that UPnP implementation does not need to include all
the HTTP functionality. In addition, make it easier to share HTTP server
functionality with other components in the future.
Instead of implementing HTTP client functionality inside
wps_upnp_event.c, use a generic HTTP client module to do this. The HTTP
client code can now be shared more easily for other purposes, too.
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
New wpa_supplicant command line options -o<driver> and -O<ctrl> can
now be used to override the parameters received in add interface
command from dbus or global ctrl_interface. This can be used, e.g.,
to enable control interface when using NetworkManager (add
-O/var/run/wpa_supplicant into the Exec parameter in
/usr/share/dbus-1/system-services/fi.epitest.hostap.WPASupplicant.service).
Similarly, this can be used to use another driver wrapper with
NetworkManager (e.g., -onl80211 to replace WEXT with nl80211).
This provides information about PBC mode result from the WPS Registrar
module. This could be used, e.g., to provide a user notification on the
AP UI on PBC failures.
Force deauthentication from the AP to clear mac80211 state (it would get
stuck with future scans if the AP is left in authenticated, but not
associated, state).
Add blacklist entry for the AP to allow other APs with worse signal
strength to be tried (e.g., when APs are trying to do load balancing
with status code 17). Reduce wait for the next scan to speed up
connection in cases where there could be other APs that could accept
association, but which show worse signal strength.
This functionality fits better with src/tls (i.e., internal TLS
implementation), so move it there to make crypto_internal.c more
of a wrapper like other crypto_*.c files.
Previously, APs that were hiding SSID (zero-length SSID IE in
Beacon frames) could have been selected when wildcard SSID matching
was used. This would result in failed association attempt since
the client does not know the correct SSID. This can slow down WPS
which is often using wildcard SSID matching.
Ignore BSSes without known SSID in the scan results when selecting
which BSS to use.
This patch completely separates supplicant's code from dbus.
It introduces three new notifications which copes with all
remaining dbus stuff.
wpas_notify_unregister_interface() was renamed to
wpas_notify_iface_removed().
The hostapd/wpa_supplicant compilation failed with CONFIG_IEEE80211R=y
or CONFIG_IEEE80211W=y option if CONFIG_EAP_PSK and CONFIG_EAP_GPSK are
not used.
mac80211 does not currently allow (re)authentication when we are already
authenticated. In order to work around this, force deauthentication if
nl80211 authentication command fails with EALREADY. Unfortunately, the
workaround code in driver_nl80211.c alone is not enough since the
following disconnection event would clear wpa_supplicant authentication
state. To handle this, add some code to restore authentication state
when using userspace SME.
This workaround will hopefully become unnecessary in some point should
mac80211 start accepting new authentication requests even when in
authenticated state.
Reorganize the TLS/crypto library segments into a single set of blocks
for each library instead of multiple locations handling library-specific
operations. Group crypto functionality together and get wpa_supplicant
and hostapd Makefile closer to eachother in order to make it easier to
eventually move this into a shared makefile.
Crypto library wrappers can now override the internal DH (group 5)
implementation. As a starting point, this is done with OpenSSL. The
new mechanism is currently available only for WPS (i.e., IKEv2 still
depends on the internal DH implementation).
Whenever running wpa_supplicant in AP mode with WPS enabled, the
notifications of missing WPS PIN are now shown on the peer dialog
to make it easier to provide the PIN.
If no BSSes/IBSSes matching the enabled networks are found in the scan
results, IBSS/AP mode network (if configured) can be created in
ap_scan=1 mode instead of requiring ap_scan=2 mode to be used whenever
using IBSS or AP mode.
This brings in the first step in adding support for using NSS
(Mozilla Network Security Services) as the crypto and TLS library
with wpa_supplicant. This version is able to run through EAP-PEAP
and EAP-TTLS authentication, but does not yet implement any
certificate/private key configuration. In addition, this does not
implement proper key fetching functions either, so the end result
is not really of much use in real world yet.
Current wpa_supplicant has a bug with WEP keys, it adds a zero-length
sequence counter field to netlink which the kernel doesn't accept.
Additionally, the kernel API slightly changed to accept keys only when
connected, so we need to send it the keys after that. For that to work
with shared key authentication, we also include the default WEP TX key
in the authentication command.
To upload the keys properly _after_ associating, add a new flag
WPA_DRIVER_FLAGS_SET_KEYS_AFTER_ASSOC_DONE indicating that the driver
needs the keys at that point and not earlier.
This allows background scanning and roaming decisions to be contained in
a single place based on a defined set of notification events which will
hopefully make it easier to experiment with roaming improvements. In
addition, this allows multiple intra-ESS roaming policies to be used
(each network configuration block can configure its own bgscan module).
The beacon loss and signal strength notifications are implemented for
the bgscan API, but the actual events are not yet available from the
driver.
The included sample bgscan module ("simple") is an example of what can
be done with the new bgscan mechanism. It requests periodic background
scans when the device remains associated with an ESS and has couple of
notes on what a more advanced bgscan module could do to optimize
background scanning and roaming. The periodic scans will cause the scan
result handler to pick a better AP if one becomes available. This bgscan
module can be taken into use by adding bgscan="simple" (or
bgscan="simple:<bgscan interval in seconds>") into the network
configuration block.
After transitioning from DISCONNECTED to SCANNING, we never go back
to DISCONNECTED even though scanning is done or failed.
We're thus stuck in SCANNING while scanning is actually done.
Convert wpa_supplicant_get_scan_results_old() to use the same return
style with the other get_scan_results options and clean up the code
by sharing the same scan result freeing and error checking code for
all the options.
Instead of implementing these separately in various control
interface handlers, use shared functions. These add some of the
previously missing notification calls, too, for the affected areas.
This introduces a new mechanism for collecting notification calls into
a single place (notify.c). As a result of this, most of the
wpa_supplicant code does not need to know about dbus (etc. mechanisms
that could use the notifications). Some empty placeholder functions are
also added in preparation of new dbus code that needs more event
notifications.
In addition, add a peer entry type for each peer entry. Currently,
this is only stored as an integer and visible in the context menu.
Eventually, different icons should be used based on this type.
This provides some initial functionality for showing peer information,
i.e., showing information about other devices that has been discovered.
Currently, information is only available in the AP mode (list of
associated stations), but this is expected to increase in the future
(e.g., show the current AP in station mode, other stations in IBSS,
etc.). Furthermore, there will be actions available for doing things
like providing a WPS PIN for a station.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
If an EAPOL frame is received while wpa_supplicant thinks the driver is
not associated, queue the frame for processing at the moment when the
association event is received. This is a workaround to a race condition
in receiving data frames and management events from the kernel.
The pending EAPOL frame will not be processed unless an association
event is received within 100 msec for the same BSSID.
wpa_supplicant can now be built with FIPS capable OpenSSL for FIPS mode
operation. Currently, this is only enabling the FIPS mode in OpenSSL
without providing any higher level enforcement in wpa_supplicant.
Consequently, invalid configuration will fail during the authentication
run. Proper configuration (e.g., WPA2-Enterprise with EAP-TLS) allows
the connection to be completed.
An SMC router was reported to use 0x22 (WPAPSK + WPA2PSK) in the
authentication type of the provisioned credential and wpa_supplicant
rejected this as invalid. Work around this by replacing WPAPSK + WPA2PSK
with WPA2PSK.
This is a (hopefully) temporary workaround to allow the same source code
tree to be used for building hostapd and wpa_supplicant without having
to manually force recompilation of some files. Currently, some of the
driver wrapper files need to be built separately for hostapd and
wpa_supplicant (#ifdef's in the files based on AP functionality).
This is somewhat racy as far as parallel make execution is concerned,
i.e., it may be necessary to run "make -j#" twice (plain "make" works
fine. Since this is supposed to be a temporary workaround, there is not
much point in trying to fix this with any more complex make processing.
Instead of having all driver stuff collected across wpa_supplicant
and hostapd, create a common snippet that they both include and
that handles the build configuration.
Change existing CONFIG_LIBNL20 compatibility code in
driver_nl80211.c to be used by both wpa_supplicant
and hostapd, but take care of nl_handle too now.
Propagate CONFIG_LIBNL20 out of .config file and onto
CFLAGS in the Makefile.
Use libnl-gen now too.
Signed-off-by: Jon Loeliger <jdl@bigfootnetworks.com>
---
Since we do not currently support changing the AP settings received
from M7, there is no point in actually sending out the M8 that would
likely trigger the AP to reconfigure itself and potentially reboot.
For now, we just receive the AP settings in M7 and add a local network
configuration block based on those, but NACK the message. This makes
wps_reg work like wps_pin, but by using the AP PIN instead of a client
PIN.
When the supplicant is connected and performs a scan, it doesn't enter
WPA_SCANNING state for various reasons. However, external programs
still need to know that the supplicant is scanning since they may not
wish to perform certain operations during a scan (as those operations
will likely fail or yield incorrect results). Add a 'scanning' property
and signal to the supplicant dbus interface to allow clients to
synchronize better with the supplicant when it scans.
Signed-off-by: Dan Williams <dcbw@redhat.com>
hostapd_cli wps_pin command can now have an optional timeout
parameter that sets the PIN lifetime in seconds. This can be used
to reduce the likelihood of someone else using the PIN should an
active PIN be left in the Registrar.
I've exported the methods wpsPbc, wpsReg and wpsPin (patch attached),
so wpa_supplicant should be able to connect with WPS using the dbus
interface. I couldn't test it well because the problem seems to be in
my wireless card, a Broadcom BCM4328. At least it seems to do the same
using both interfaces. With ndiswrapper driver the "wpsie" entry
(thanks Dan!) didn't appear, and with the Broadcom wl driver it
appears but I cannot associate using WPS.
Add a new DBus method "setDebugParams" which takes the parameters
debug_level, debug_timestamp and show_keys as input and updates the
internal debug variables accordingly.
To change the debug level, enable/disable timestamps and enable/disable
show_keys the following dbus-send command can be used:
dbus-send --system --dest=fi.epitest.hostap.WPASupplicant --print-reply
/fi/epitest/hostap/WPASupplicant fi.epitest.hostap.WPASupplicant.setDebugParams
int32:0 boolean:false boolean:false
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
When in AP mode, wpa_supplicant is now enabling WPS (only Internal
Registrar). wpa_cli wps_pbc and wps_pin commands can be used to initiate
WPS negotiation similarly to how this is done in station mode (though,
the BSSID parameter is ignored).
There is no point in trying to continue if a 4-way handshake frame is
discarded or if PTK/GTK/IGTK configuration fails. Force the client to
disconnect in such a case to avoid confusing user by claiming the
connection was successfully completed.
Use a parameter structure to pass in information that can be more easily
extended in the future. Include some of the parameters that were
previously read directly from hapd->conf in order to reduce need for
including hostapd/config.h into driver wrappers.
This merges the driver wrapper implementations to use the same
implementation both for hostapd and wpa_supplicant operations to avoid
code duplication.
This commit merges the driver_ops structures and implementations from
hostapd/driver*.[ch] into src/drivers. This is only an initial step and
there is room for number of cleanups to share code between the hostapd
and wpa_supplicant parts of the wrappers to avoid unnecessary source
code duplication.
Need to set WEP keys before requesting authentication in order to get
Shared Key authentication working. Previously, the WEP keys were not set
at all when using SME in wpa_supplicant.
IEEE 802.11r KDF uses key length in the derivation and as such, the PTK
length must be specified correctly. The previous version was deriving
using 512-bit PTK regardless of the negotiated cipher suite; this works
for TKIP, but not for CCMP. Update the code to use proper PTK length
based on the pairwise cipher.
This fixed PTK derivation for both IEEE 802.11r and IEEE 802.11w (when
using AKMP that specifies SHA-256-based key derivation). The fixed
version does not interoperate with the previous versions. [Bug 307]
Update credential to only include a single authentication and
encryption type in case the AP configuration includes more than one
option. Without this, the credential would be rejected if the AP was
configured to allow more than one authentication type.
A new network block parameter, scan_freq, can be used to specify subset
of frequencies to scan. This can speed up scanning process considerably
if it is known that only a small subset of channels is actually used in
the network. A union of configured frequencies for all enabled network
blocks is used in scan requests.
Currently, only driver_nl80211.c has support for this functionality.
For example, following parameter marks 2.4 GHz channels 1, 6, 11 to be
scanned: scan_freq=2412 2437 2462
wpa_supplicant can now initialize hostapd data structures when mode=2 is
used to set up an AP. The hostapd configuration is not yet set based on
wpa_supplicant network configuration block. In addition, the glue code
for hostapd driver_ops needs number of functions that will be needed for
AP functionality.
Move the shared IEEE 802.11w enum definition into src/common/defs.h to
avoid redefinition when both configuration structures are included into
the same file.
This version is adding the configuration option (mode=2) for this and
driver capability reporting to figure out whether AP mode can be used.
However, this does not actually implement any real functionality yet.
All these driver handlers can be implemented in associate() handler
which gets all the needed information in the parameters structure. The
old functions that provided only a single parameter will be removed
eventually to clean up the driver_ops structure, so driver wrappers
should start using the newer mechanism.
Removing just sun_family is not portable since some systems (e.g.,
FreeBSD) include an additional sun_len field. Using offsetof should be
portable. In addition, set sun_ken for FreeBSD.
This can be used, e.g., with mac80211-based Linux drivers with
nl80211. This allows over-the-air FT protocol to be used (IEEE
802.11r).
Since the nl80211 interface needed for this is very recent (added
today into wireless-testing.git), driver_nl80211.c has backwards
compatibility code that uses WEXT for association if the kernel does
not support the new commands. This compatibility code can be
disabled by defining NO_WEXT_COMPAT. That code will also be removed
at some point to clean up driver_nl80211.c.
This adds first part of FT resource request as part of Reassocition
Request frame (i.e., FT Protocol, not FT Resource Request Protocol).
wpa_supplicant can generate a test resource request when driver_test.c
is used with internal MLME code and hostapd can verify the FTIE MIC
properly with the included RIC Request.
The actual RIC Request IEs are not processed yet and hostapd does not
yet reply with RIC Response (nor would wpa_supplicant be able to
validate the FTIE MIC for a frame with RIC Response).
This is done with wired interfaces to fix IEEE 802.1X authentication
when the authenticator uses the group address (which should be happening
with wired Ethernet authentication).
This allows wpa_supplicant to complete wired authentication successfully
on Vista with a NDIS 6 driver, but the change is likely needed for
Windows XP, too.
Do not use just the driver name for this since driver_ndis.c supports
both wired and wireless NDIS drivers and needs to indicate the driver
type after initialization.
Calculate the estimated medium time using integer variables since there
is no real need to use floating point arithmetics here. In addition,
make sure there is no division by zero regardless of how invalid the
request from the station is. Reject invalid parameters and refuse
requests that would take most of the bandwidth by themselves.
Add test code into wpa_supplicant mlme.c to allow WMM-AC negotiation to
be tested with driver_test.
The new file wps_nfc.c and ndef.c implements NFC device independent
operation, wps_nfc_pn531.c implements NFC device dependent operation.
This patch is only for the following use case:
- Enrollee = wpa_supplicant
- Registrar = hostapd internal Registrar
Following NFC methods can be used:
- Enrollee PIN with NFC
- Registrar PIN with NFC
- unencrypted credential with NFC
Encrypted credentials are not supported.
Enrollee side operation:
Registrar side operation:
Example configuration.
CONFIG_WPS=y
CONFIG_WPS_NFC=y
CONFIG_WPS_NFC_PN531=y
I used NFC device "NXP PN531". The NFC device access method is
confidential, so I used outer library. Please download below files from
https://www.saice-wpsnfc.bz/index.php
[WPS NFC Library]
WpsNfcLibrary/WpsNfc.h
WpsNfcLibrary/WpsNfcType.h
WpsNfcLibrary/WpsNfcVersion.h
WpsNfcLibrary/linux/libnfc_mapping_pn53x.dll
WpsNfcLibrary/linux/wpsnfc.dll
[NFC Reader/Writer Kernel Driver]
NFCKernelDriver-1.0.3/linux/kobj/sonyrw.ko
<WiFi test>
The hostapd/wpa_supplicant with this patch passed below tests on
"Wi-Fi WPS Test Plan Version 1.6".
4.2.5 Add device using NFC Method with password token
(I used SONY STA instead of NXP STA.)
4.2.6 Add device using NFC Method with configuration token
5.1.9 Add to AP using NFC Method with password token
through internal registrar
(I used SONY AP instead of NXP AP.)
5.1.10 Add to AP using NFC Method with configuration token
through internal registrar
Many deployed APs do not handle negotiation of security parameters well
when both TKIP and CCMP (or both WPA and WPA2) are enabled. The most
common end result seems to be ending up with the least secure option..
As a workaround, check whether the AP advertises WPA2/CCMP in Beacon
frames and add those options for the credential if needed. This allows
the client to select the most secure configuration regardless of how
broken the AP's WPS implementation is as far as auth/encr type
negotiation is concerned.
The old behavior of generating new DH keys can be maintained for non-OOB
cases and only OOB (in this case, with UFD) will use the pre-configured
DH keys to allow the public key hash to be checked.
Not all embedded devices have USB interface and it is useful to be able
to remove unneeded functionality from the binary. In addition, the
current implementation has some UNIX specific calls in it which may make
it not compile cleanly on all target systems.
It seems that WFA WPS spec says that default key index should be 1 (not
0). I think this meas that WEP key indexes region is not from 0 to 3,
but from 1 to 4 in WPS. At least WRT610N implemented it this way.
These flags are used to mark which values (level, noise, qual) are
invalid (not available from the driver) and whether level is using dBm.
D-Bus interface will now only report the values that were available.
If the driver reports support for more than one SSID per scan request,
optimize scan_ssid=1 operations in ap_scan=1 mode. This speeds up
scanning whenever scan_ssid=1 is used since the broadcast SSID can be
included in every scan request and if driver supports more than two
SSIDs in the scan request, the benefits are even larger when multiple
networks have been configured with ap_scan=1.
This is also cleaning up wpa_supplicant_scan() function by moving code
around so that the SSID list is not processed unnecessarily if the
operation mode does not need this.
This can be used to provide support for scanning multiple SSIDs at a
time to optimize scan_ssid=1 operations. In addition, Probe Request IEs
will be available to scan2() (e.g., for WPS PBC scanning).
For example, -Dnl80211,wext could be used to automatically select
between nl80211 and wext. The first driver wrapper that is able to
initialize the interface will be used.
The driver wrappers can now inform wpa_supplicant how many SSIDs can
be used in a single scan request (i.e., send multiple Probe Requests
per channel). This value is not yet used, but it can eventually be used
to allow a new scan command to specify multiple SSIDs to speed up
scan_ssid=1 operations. In addition, a warning could be printed if
scan_ssid=1 is used with a driver that does not support it
(max_scan_ssids=0).
Split the auth=none option into three: open, WEP, WEP with shared key to
allow the user specify WEP with shared key authentication. In addition,
fix static WEP key edits to be enabled only when using static WEP keys
(i.e., not for IEEE 802.1X).
wpa_supplicant should not send a dbus reply as response to a method call
if no reply was requested by the caller. Sending a reply even if not
requested is basically no problem but triggers dbus warnings like the
one below.
Feb 9 07:31:23 linux-gvjr dbus-daemon: Rejected send message, 2 matched
rules; type="error", sender=":1.129" (uid=0 pid=30228
comm="/usr/sbin/wpa_supplicant -c /etc/wpa_supplicant/wp")
interface="(unset)" member="(unset)" error
name="fi.epitest.hostap.WPASupplicant.InvalidInterface"
requested_reply=0 destination=":1.128" (uid=0 pid=30226
comm="/usr/sbin/NetworkManager "))
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Build EAP-WSC dynamically does not make much sense and with the
dependencies to WPS code from number of places resolving this is not
trivial. It is simpler to just remove this option.
If you don't choose OpenSSL as TLS implementation and choose to enable
CONFIG_EAP_TNC you have to link against libdl. The OpenSSL libraries
implicitly link against them, so this might be a reason why it wasn't
noticed yet. I assume the same applies to hostapd.
We can now handle up to 65535 byte result buffer which is the maximum
due to WEXT using 16-bit length field. Previously, this was limited to
32768 bytes in practice even through we tried with 65536 and 131072
buffers which we just truncated into 0 in the 16-bit variable.
This more or less doubles the number of BSSes we can received from scan
results.
If wpa_supplicant is started with -u but the DBus service is already
registered wpa_supplicant will bail out. However, it will segfault
in wpa_supplicant_deinit because global->drv_priv wasn't allocated
yet.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This is based on a patch from Pavel Roskin <proski@gnu.org>, but with
the WIRELESS_DEV part removed instead of moved since it does not apply
anymore. Additional note on client MLME limitations was also added.
MadWifi is unlikely to be in ../head relative to hostapd or
wpa_supplicant, as it would be inside the hostap git repository.
MadWifi sources are more likely to be in a directory called "madwifi"
and residing outside the hostap repository. Using "madwifi" also
demonstrates that the top-level madwifi directory is needed.
If a Registrar tries to configure the AP, but fails to validate the
device password (AP PIN), lock the AP setup after four failures. This
protects the AP PIN against brute force guessing attacks.
Some WPS APs do not set Selected Registrar attribute to 1 properly when
using an external Registrar. Allow such an AP to be selected for PIN
registration after couple of scan runs that do not find APs marked with
Selected Registrar = 1. This allows wpa_supplicant to iterate through
all APs that advertise WPS support without delaying connection with
implementations that set Selected Registrar = 1 properly.
The default interval is now 5 seconds (used to be 1 second for
interactive mode and 2 seconds for wpa_cli -a). The interval can be
changed with -G<seconds> command line option.
The separate Association Comeback Time IE was removed from IEEE 802.11w
and the Timeout Interval IE (from IEEE 802.11r) is used instead. The
editing on this is still somewhat incomplete in IEEE 802.11w/D7.0, but
still, the use of Timeout Interval IE is the expected mechanism.
The wps_cred_process option can be used to configure wpa_supplicant to
send received Credential attributes for external processing over
ctrl_iface and dbus. This allows external programs to update their
configuration when WPS is used to provision new networks.
This makes it easier to pass the credential data to external programs
(e.g., Network Manager) for processing. The actual use of this data is
not yet included in hostapd/wpa_supplicant.
The current implementation does not support WPA/WPA2-Enterprise
credentials. Ignore any credential that is using unsupported
authentication type to avoid potential issues with partially configured
network blocks.
Must not set pairwise_cipher/group_cipher for non-WPA/WPA2 networks
since the configuration parser is going to reject such values. In
addition, should not limit group_cipher to just TKIP or TKIP|CCMP just
in case the AP is using WEP as the group cipher. Default group_cipher
value can be used for all cases.
RSN IBSS uses authentication per-STA and that is initialized separately,
so there is no need to enable the per-BSS like authentication that is
used with APs.
This makes wpa_gui remember whether it was only in the tray when the
session was terminated and starts only in the tray if session manager
restarts it automatically.
This commit adds a new build option, CONFIG_IBSS_RSN=y, that can be used
to enable RSN support for IBSS. This links in RSN Authenticator code
from hostapd and adds code for managing per-peer information for IBSS. A
new wpa_cli command or driver event can be used to request RSN
authentication with an IBSS peer. New RSN Authenticator and Supplicant
will be allocated for each peer.
The basic state machine setup code is included in this commit, but the
state machines are not properly started yet. In addition, some of the
callback functions are not yet complete.
Do not add the automatically generated RADIUS attributes NAS-IP-Address,
Calling-Station-Id, Framed-MTU, NAS-Port-Type, and Connect-Info if -N
option is used with the same attribute type. This allows these
attributes to be replaced without causing duplicate entries.
Fix compile warning by renaming gridLayout to wpsGridLayout in
wpagui.ui, it seems to be used internally.
/usr/bin/uic-qt4 eventhistory.ui -o .ui/ui_eventhistory.h
/usr/bin/uic-qt4 scanresults.ui -o .ui/ui_scanresults.h
/usr/bin/uic-qt4 wpagui.ui -o .ui/ui_wpagui.h
Warning: name gridLayout is already used
/usr/bin/uic-qt4 userdatarequest.ui -o .ui/ui_userdatarequest.h
/usr/bin/uic-qt4 networkconfig.ui -o .ui/ui_networkconfig.h
Also disable WPS tab if the running supplicant doesn't support that,
just as the WPS action menu is.
Signed-off-by: Kel Modderman <kel@otaku42.de>
It is better to have command description around the command definitions:
the chances for omitting usage, forgotting to change/delete them, etc.
are smaller than for the separate usage statement. [Bug 290]
Signed-off-by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>
I had added flags to the every command description: just now the only
meaningful flag tells that this command has sensitive arguments and it
shouldn't be written to the disk. I rewrote the logics for the search
for the sensitive commands: special procedure is now loops over all
commands and tries to see if command has sensitive data. [Bug 289]
Signed-off-by: Eygene Ryabinkin <rea-fbsd@codelabs.ru>
First of all, the history had not been written to the disk, since almost
all commands were cleaned up due to the error in the history cleaning:
the return value of the last os_strncasecmp() call was not compared to
zero, but was rather used as is. So the condition was almost always
true and most commands were removed from the history.
The second problem was that the evaluation of the potentially sensitive
commands was started at the entry number 1, instead of very first entry.
This change replaces -I and -i options (Chargeable-User-Identity) with a
new -N option that can add any RADIUS attribute into the Access-Request
messages without having to modify eapol_test for each new attribute.
Replace " wpa_supplicant" with " %wpa_supplicant" except for
"struct wpa_supplicant". This makes it easier to write Doxygen comments
since there is no need to add the ugly '%' prefix to each instance of
wpa_supplicant text showing up.
This updated all doxygen runs to use the same style that was used for
wpa_supplicant full documents. The full vs. fast configurations are now
otherwise identical apart from fast not generating dot files or
latex/pdf version of the documentation.
Generate a SHA1 hash -based UUID from the local MAC address if the UUID
was not configured. This makes it easier to prepare for WPS since there
is no need to generate an UUID.
When using ap_scan=1, we know before the association request that MFP
will be supported, so we can as well require it. This helps mac80211 in
configuring whether to enable MFP.
This commit changes just the name and Action category per D7.0. The
retransmit/timeout processing in the AP is not yet updated with the
changes in D7.0.
It seems that for WPS registration we should use the same authentication
timeout as for ieee8021x, no? (See patch attached.) On slow platforms
public keys computation may take around 4-5 seconds (we actually stuck
on this issue).
Set ctrl_interface to non-empty value in INTERFACE_ADD to avoid
ctrl_iface.c assuming the control interface is not to be enabled. This
fixes the dynamically added interface to use control interface.
The NSIS installer will now add Windows registry entries for
wpa_supplicant during installation and removes them during
uninstallation. This allows wpa_gui to start wpasvc and add new
interfaces without requiring the user to do any manual registry
editing.
"Add interface" command in File menu can now be used to add a new
network interface to running wpa_supplicant (using INTERFACE_ADD control
interface command). In addition, the network interface is added into
Windows registry (with skip_on_error) for future use. This functionality
is currently enabled only for Windows builds. The user is also prompted
about the possibility of adding an interface if no interfaces are
enabled. This makes it easier to get started without having to touch
registry manually.
This can be used to include binding information for multiple interfaces
in Windows registry and only use the ones that match with an available
network interface.
The new INTERFACE_LIST global control interface command can be used to
request a list of all available network interfaces that could be used
with the enabled driver wrappers. This could be used to enable
interfaces automatically by external programs (e.g., wpa_gui).
Driver wrappers can now register global_init() and global_deinit()
driver_ops handlers to get a global data structure that can be shared
for all interfaces. This allows driver wrappers to initialize some
functionality (e.g., interface monitoring) before any interfaces have
been initialized.
UUID-E is not required to be present in Beacon frame, so we need to
accept scan results that do not have UUID-E as a valid PBC situation as
long as not more than one AP is in active PBC mode.
wpa_gui will now ask user whether the wpasvc service should be started
if it is not running. In addition, File menu has items for starting and
stopping the service.
Change association behavior to match with ap_scan=1 when WPS is used in
ap_scan=2 mode with wildcard SSID matching. In addition, allow hardcoded
BSSID to be used to select AP even if selected registrar attribute is
not present.
A separate cross compiler mkspecs file (win32-x-g++) is now used to
configure all build options so the setup-mingw-cross-compiling hack is
not needed anymore. Furthermore, the MinGW setup is now on path, so no
need to specify extra PATH changes for it.
This callback is now used to stop wpa_supplicant from trying to continue
using parameters (most likely, device password) that do not work in a
loop. In addition, wpa_gui can now notify user of failed registration.
The event callback will be used for various event messages and the M2D
notification is the first such message. It is used to notify wpa_gui
about Registrar not yet knowing the device password (PIN).
We need to be a bit more careful when removing the WPS configuration
block since wpa_s->current_ssid may still be pointing at it. In
addition, registrar pointer in wps_context will need to be cleared
since the context data is now maintained over multiple EAP-WSC runs.
Without this, certain WPS operations could have used freed memory.
The specific AP (BSSID) can now be selected through scan results for
WPS (WPS pushbutton on the network configuration dialog). When a BSSID
is selected, AP device PIN (e.g., from a label) can be used to configure
the AP by acting as a Registrar.
Whenever new scan results include WPS AP(s) and the client is not
associated, send a notification message to control interface monitors.
This makes it easier for GUIs to notify the user about possible WPS
availability without having to go through the scan results.
Windows Server 2008 NPS gets very confused if the TLS Message Length is
not included in the Phase 1 messages even if fragmentation is not used.
If the TLS Message Length field is not included in ClientHello message,
NPS seems to decide to use the ClientHello data (excluding first six
octets, i.e., EAP header, type, Flags) as the OuterTLVs data in
Cryptobinding Compound_MAC calculation (per PEAPv2; not MS-PEAP)..
Lets add the TLS Message Length to PEAPv0 Phase 1 messages to get rid of
this issue. This seems to fix Cryptobinding issues with NPS and PEAPv0
is now using optional Cryptobinding by default (again) since there are
no known interop issues with it anymore.
Changed peer to derive the full key (both MS-MPPE-Recv-Key and
MS-MPPE-Send-Key for total of 32 octets) to match with server
implementation.
Swapped the order of MPPE keys in MSK derivation since server
MS-MPPE-Recv-Key | MS-MPPE-Send-Key matches with the order specified for
EAP-TLS MSK derivation. This means that PEAPv0 cryptobinding is now
using EAP-MSCHAPv2 MSK as-is for ISK while EAP-FAST will need to swap
the order of the MPPE keys to get ISK in a way that interoperates with
Cisco EAP-FAST implementation.
driver_test can now be used either over UNIX domain socket or UDP
socket. This makes it possible to run the test over network and makes it
easier to port driver_test to Windows.
hostapd configuration: test_socket=UDP:<listen port>
wpa_supplicant configuration: driver_param=test_udp=<dst IP addr>:<port>
This adds support for setting of a regulatory domain to wpa_supplicant
drivers. It also adds regulatory domain setting for the nl80211 driver.
We expect an ISO / IEC 3166 alpha2 in the wpa configuration file as a
global.
Print the password field only if -K is given by using wpa_hexdump_ascii_key
instead of wpa_hexdump_ascii. Additionally mark the password field as key.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
This is just making an as-is copy of EAP-AKA server and peer
implementation into a new file and by using the different EAP method
type that is allocated for EAP-AKA' (50). None of the other differences
between EAP-AKA and EAP-AKA' are not yet included.
It is likely that once EAP-AKA' implementation is done and is found to
work correctly, large part of the EAP-AKA and EAP-AKA' code will be
shared. However, it is not reasonable to destabilize EAP-AKA
implementation at this point before it is clearer what the final
differences will be.
Previously, this was only done when the new connection is using
WPA-Personal. However, it looks like it was possible to trigger an
infinite busy loop if altAccept or altReject were left set to true and
an EAPOL frame is received (eapolEap is set to true). Clearing altAccept
and altReject for each association prevents this loop from happening in
the beginning of the next association.
Fragment WPS IE if needed to fit into the IE length limits in hostapd
and Reassemble WPS IE data from multiple IEs in wpa_supplicant.
In addition, moved WPS code from events.c into wps_supplicant.c to clean
up module interfaces.
New control interface commands WPS_PBC, WPS_PIN, and WPS_REG can be used
to start WPS processing. These add and select the WPS network block into
the configuration temporarily, i.e., there is no need to add the WPS
network block manually anymore.
The wps_context data is now managed at wpa_supplicant, not EAP-WSC. This
makes wpa_supplicant design for WPS match with hostapd one and also
makes it easier configure whatever parameters and callbacks are needed
for WPS.
Previously, wpa_supplicant as Enrollee case was handled using a
different callback function pointer. However, now that the wps_context
structure is allocated for all cases, the same variable can be used in
all cases.
This cleans up the internal interface between different modules and is
the first step in getting wpa_supplicant design closer to hostapd as far
as WPS is concerned.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
It looks like some Windows NDIS drivers (e.g., Intel) do not clear the
PMKID list even when wpa_supplicant explicitly sets the list to be
empty. In such a case, the driver ends up trying to use PMKSA caching
with the AP and wpa_supplicant may not have the PMK that would be needed
to complete 4-way handshake.
RSN processing already had some code for aborting PMKSA caching by
sending EAPOL-Start. However, this was not triggered in this particular
case where the driver generates the RSN IE. With this change, this case
is included, too, and the failed PMKSA caching attempt is cleanly
canceled and wpa_supplicant can fall back to full EAP authentication.
It looks like Qt does not support SVG format by default on Windows and
it was not trivial to add the plugin into the build, so for now, build a
16x16 PNG icon file for Windows binary to avoid showing an invisible
icon in the tray.
I fixed the engine issue in phase2 of EAP-TTLS. The problem was that you
only defined one engine variable, which was read already in phase1. I
defined some new variables:
engine2
engine2_id
pin2
and added support to read those in phase2 wheres all the engine
variables without number are only read in phase1. That solved it and I
am now able to use an engine also in EAP-TTLS phase2.
Find attached the patch that creates a new driver: roboswitch. This
driver adds support for wired authentication with a Broadcom
RoboSwitch chipset. For example it is now possible to do wired
authentication with a Linksys WRT54G router running OpenWRT.
LIMITATIONS
- At the moment the driver does not support the BCM5365 series (though
adding it requires just some register tweaks).
- The driver is also limited to Linux (this is a far more technical
restriction).
- In order to compile against a 2.4 series you need to edit
include/linux/mii.h and change all references to "u16" in "__u16". I
have submitted a patch upstream that will fix this in a future version
of the 2.4 kernel. [These modifications (and more) are now included in
the kernel source and can be found in versions 2.4.37-rc2 and up.]
USAGE
- Usage is similar to the wired driver. Choose the interfacename of
the vlan that contains your desired authentication port on the router.
This name must be formatted as <interface>.<vlan>, which is the
default on all systems I know.
Remove the old code from driver_wext.c since the private ioctl interface is
never going to be used with mac80211. driver_nl80211.c has an
implementation than can be used with mac80211 (with two external patches to
enable userspace MLME configuration are still required, though).
Updated OpenSSL code for EAP-FAST to use an updated version of the
session ticket overriding API that was included into the upstream
OpenSSL 0.9.9 tree on 2008-11-15 (no additional OpenSSL patch is
needed with that version anymore).
GCC 4.4 cleaned up some more C++ headers. You always have to #include
headers directly and cannot rely for things to be included indirectly.
> g++ -c -pipe -O2 -Wall -W -D_REENTRANT -DCONFIG_CTRL_IFACE
-DCONFIG_CTRL_IFACE_UNIX -DQT_NO_DEBUG -DQT_GUI_LIB -DQT_CORE_LIB -DQT_SHARED
-I/usr/share/qt4/mkspecs/linux-g++ -I. -I/usr/include/qt4/QtCore
-I/usr/include/qt4/QtCore -I/usr/include/qt4/QtGui -I/usr/include/qt4/QtGui
-I/usr/include/qt4 -I. -I.. -I../../src/utils -I../../src/common -I.moc -I.ui -o
.obj/wpagui.o wpagui.cpp
> wpagui.cpp: In constructor 'WpaGui::WpaGui(QWidget*, const char*,
Qt::WFlags)':
> wpagui.cpp:98: error: 'printf' was not declared in this scope
From: Martin Michlmayr <tbm@cyrius.com>
Bug: http://bugs.debian.org/505041
Signed-off-by: Kel Modderman <kel@otaku42.de>
delaying Michael MIC error reports by a random amount of time between 0 and
60 seconds if multiple Michael MIC failures are detected with the same PTK
(i.e., the Authenticator does not rekey PTK on first failure report). This
is disabled by default and can be enabled with a build option
CONFIG_DELAYED_MIC_ERROR_REPORT=y in .config.
This may help in making a chopchop attack take much longer time by forcing
the attacker to wait 60 seconds before knowing whether a modified frame
resulted in a MIC failure.
Added a new configuration option, wpa_ptk_rekey, that can be used to
enforce frequent PTK rekeying, e.g., to mitigate some attacks against TKIP
deficiencies. This can be set either by the Authenticator (to initiate
periodic 4-way handshake to rekey PTK) or by the Supplicant (to request
Authenticator to rekey PTK).
With both wpa_ptk_rekey and wpa_group_rekey (in hostapd) set to 600, TKIP
keys will not be used for more than 10 minutes which may make some attacks
against TKIP more difficult to implement.
This may be needed if the AP does not disconnect in case of EAP-FAST
unauthenticated provisioning (EAP-Failure). Adding the local short timeout
will speed up the process in such a case by reducing the wait (which can
often be up to 60 seconds).
This allows identity (etc.) variables to be removed from configuration
which is different from setting them to an empty string. For example,
EAP-SIM and EAP-AKA can now be configured to use identity string generation
from SIM/USIM by clearing the identity string in wpa_gui.
Setting the value of the SET_NETWORK command to NULL (without quotation)
unsets the variable, i.e., removes it from configuration file. This is
needed to allow GUI programs to clear variables, e.g., identity for
EAP-AKA/SIM.
Allow application to be started in the system tray only when started with
the `-t' command line argument.
Signed-off-by: Kel Modderman <kel@otaku42.de>
When the system tray icon is created, qApp's setQuitOnLastWindowClosed
property is set to false, therefore do _not_ ignore widget close events, or
else wpa_gui will refuse to exit when the window manager is logging out.
While at it, remove WpaGui::fileExit() and connect fileExitAction to
quit().
Signed-off-by: Kel Modderman <kel@otaku42.de>
A bug just got reported as a result of this for mac80211 drivers.
https://bugzilla.redhat.com/show_bug.cgi?id=459399
The basic problem is that since taking the device down clears the keys
from the driver on many mac80211-based cards, and since the mode gets
set _after_ the keys have been set in the driver, the keys get cleared
on a mode switch and the resulting association is wrong. The report is
about ad-hoc mode specifically, but this could happen when switching
from adhoc back to managed mode.
This function was getting way too long, so let's split it into WPA and
non-WPA cases as separate functions. In addition, remove the confusing
"Try to find non-WPA AP" debug message if a WPA-enabled AP is already
selected (as reported by Andriy Tkachuk).
but still show a one time tray message to indicate to the user that the
program is still running in the tray if they triggered the window manager
close button.
Signed-off-by: Kel Modderman <kel@otaku42.de>
Do not connect lastWindowClosed() to quit(), instead explicitly close the
application if File->Exit or window manager close button is activated.
This allows the tray app to avoid being closed with last visible window,
and launch scan and event history windows individually.
Signed-off-by: Kel Modderman <kel@otaku42.de>
Enhance the wpa_gui-qt4 icon:
* removed unused layer
* moved spurious rectangle back where it belongs
* removed flat edge from top of the lower white glow object
Signed-off-by: Bernard Gray <bernard.gray@gmail.com>
mlme.c: In function 'ieee80211_rx_mgmt_action':
mlme.c:1990: warning: implicit declaration of function
'ieee80211_rx_mgmt_ping_action'
...
mlme.o(.text+0x3007): In function `ieee80211_sta_rx':
/home/ant/hostap/hostap06/hostap/wpa_supplicant/mlme.c:1990: undefined reference
to `ieee80211_rx_mgmt_ping_action'
collect2: ld returned 1 exit status
When the initial scan is made, just the cached results from the driver
are used. If this is empty, it's useless to post the results since
another scan is being scheduled immediately. This just causes extra
processing from listeners for no gain.
The scan path to initiate another scan if the initial association failed
was broken due to wpa_s->scan_req being zeroed earlier in
wpa_supplicant_scan(). This caused the second scan to bail out early
since it thought this was not a requested scan.
Add system tray icon support to wpa_gui-qt4. The tray icon remains quiet
when the main dialog is visible, so it should not cause too much pain for
more conservative users of wpa_gui. The addition involves the following
changes:
* when closing wpa_gui via window manager close box, wpa_gui close event is
ignored and it is minimised to system tray. A status message is displayed
(or popup dialog box if tray messages are not supported) to provide a
visual hint that the program is still running in the background.
* add File->Exit slot handler to facilitate application quit from main
dialog
* provide a context menu with a short list of useful actions
* show/hide main dialog when icon is triggered (single click)
* ensure main dialog is visible when event handler or scan results is
chosen from tray icon context menu
* show tray messages on connected and disconnected events, display a status
message a few seconds after connected events
Signed-off-by: Kel Modderman <kel@otaku42.de>
When integrating the new art, this UI entry:
<pixmapfunction>qPixmapFromMimeSource</pixmapfunction>
Caused the following error:
.obj/wpagui.o: In function `Ui_WpaGui::setupUi(QMainWindow*)':
wpagui.cpp:(.text._ZN9Ui_WpaGui7setupUiEP11QMainWindow[Ui_WpaGui::setupUi(QMainWindow*)]+0xd3): undefined reference to `qPixmapFromMimeSource(QString const&)'
collect2: ld returned 1 exit status
Removing qPixmapFromMimeSource seems to have no unwanted side effects, and
allows successful build again. Research leads me to believe it depends on
Qt3Support, which we do not want.
Signed-off-by: Kel Modderman <kel@otaku42.de>
Introducing an original wpa_gui icon, in svg format, with Makefile for
easy conversion to other icon formats. The icon is thanks to Bernard Gray.
Signed-off-by: Bernard Gray <bernard.gray@gmail.com>
Signed-off-by: Kel Modderman <kel@otaku42.de>
IEEE 802.11w/D6.0 defines new AKMPs to indicate SHA256-based algorithms for
key derivation (and AES-CMAC for EAPOL-Key MIC). Add support for using new
AKMPs and clean up AKMP processing with helper functions in defs.h.
This updates management frame protection to use the assocition ping process
from the latest draft (D6.0) to protect against unauthenticated
authenticate or (re)associate frames dropping association.
This adds most of the new frame format and identifier definitions from IEEE
802.11w/D6.0. In addition, the RSN IE capability field values for MFP is
replaced with the new two-bit version with MFPC (capable) and MFPR
(required) processing.
This adds some parts needed to use usermode MLME with the current mac80211
(plus a patch to add a new cfg80211 command; not yet submitted to
wireless-testing). This version creates a monitor interface for management
frames and is able to send Probe Request frames during scan. However, it
looks like management frame reception is not yet working properly. In
addition, mlme_{add,remove}_sta() handlers are still missing.
wpa_sm_set_config() can be called even if the network block does not
change. However, the previous version ended up calling
pmksa_cache_notify_reconfig() every time and this cleared the network
context from PMKSA cache entries. This prevented OKC from ever being used.
Do not call pmksa_cache_notify_reconfig() if the network context remains
unchanged to allow OKC to be used.
When scan results got moved from wpa_scan_result -> wpa_scan_res, the
'maxrate' member was dropped from wpa_scan_res. The D-Bus interface
used 'maxrate', which was replaced with wpa_scan_get_max_rate().
Unfortunately, wpa_scan_get_max_rate() returns 802.11 rate values
directly from the IE, where 'maxrate' was the rate in bits/second. The
supplicant internally fakes an IE for wpa_scan_res from the value of
wpa_scan_result->maxrate, but interprets ->maxrate as an 802.11 rate
index.
As a side-effect, this fixes a soft-break of the D-Bus control API since
the wpa_scan_res change was introduced.
Function 'wpa_sm_set_config' used the argument 'config' as the network
context which is a pointer to a local variable of the function
'wpa_supplicant_rsn_supp_set_config'.
This is one reason why no proactive key was generated. This network
context never matched with the network context saved in the pmksa cache
entries.
The structure 'rsn_supp_config' has already a member 'network_ctx' which
is now filled in by this patch with 'ssid'.
Signed-off-by: Michael Bernhard <michael.bernhard@bfh.ch>
Documentation appeared a little vague about which options are global and
which are tied to a particular interface. This leads to confusion when
using certain combinations of options, e.g. the command "wpa_supplicant
-c /etc/wpa_supplican.conf -u" will not do what is intuitively expected
from it - it will not read the config file given with -c option because
no -i option was given. This command is still valid because -u option is
used. The wpa_supplicant running like this will also not listen on any
control socket, because the socket file name is usually given in the
config file. This command line also happens to be the default in Fedora 9.
This patch does not try to change any behaviour, but rather document
these nuances clearly.
This avoids getting stuck in state where wpa_supplicant has canceled scans,
but the driver is actually in disassociated state. The previously used code
that controlled scan timeout from WPA module is not really needed anymore
(and has not been needed for past four years since authentication timeout
was separated from scan request timeout), so this can simply be removed to
resolved the race condition. As an extra bonus, this simplifies the
interface to WPA module.
[Bug 261]
driver_nl80211.c is based on driver_wext.c and it is still using Linux
wireless extensions for many functions. Over time, the new driver interface
code should be modified to use nl80211/cfg80211 for everything.
This was not accurate since this was mostly based on total runtime of an
eapol_test run. The real improvement in the bignum routines is much larger
(mayby twice as fast as before).
CONFIG_INTERNAL_LIBTOMMATH_FAST=y in .config can now be used to enable all
optimized routines at a cost of about 4 kB. This is small enough increase
in size to justify simplified configuration.
At the cost of about 1 kB of additional binary size, the internal
LibTomMath can be configured to include faster div routine to speed up DH
and RSA. This can be enabled with CONFIG_INTERNAL_LIBTOMMATH_FAST_DIV=y in
.config.
At the cost of about 0.5 kB of additional binary size, the internal
LibTomMath can be configured to include faster sqr routine to speed up DH
and RSA. This can be enabled with CONFIG_INTERNAL_LIBTOMMATH_FAST_SQR=y in
.config.
Depending on how the driver implements IBSS searching and creation, it
may need to perform one or more scans before successfully completing the
association operation. Therefore, increase the timeout for IBSS
association operations so that the supplicant doesn't interrupt the
driver as much.
Add a cost of about 2.5 kB of additional cost, the internal LibTomMath can
be configured to include fast exptmod routine to speed up DH and RSA.
This can be enabled with CONFIG_INTERNAL_LIBTOMMATH_FAST_EXPTMOD=y in
.config.
In situations where the driver does background scanning and sends a
steady stream of scan results, wpa_supplicant would continually
reschedule the scan. This resulted in specific SSID scans never
happening for a hidden AP, and the supplicant never connecting to the AP
because it never got found. Instead, if there's an already scheduled
scan, and a request comes in to reschedule it, and there are enabled
scan_ssid=1 network blocks, let the scan happen anyway so the hidden
SSID has a chance to be found.
The internal TLS implementation can now use both PKCS #1 RSA private key
and PKCS #8 encapsulated RSA private key. PKCS #8 encrypted private key is
not yet supported.
The TLS client changes in ssl3_get_server_hello() were based on the
pre-RFC 5077 version of OpenSSL and they hardcoded s->hit to 1 in case
PAC-Opaque was used. This prevented fallback to full TLS handshake in case
the server rejected PAC-Opaque in ClientHello. The fixed version simplifies
ssl3_get_server_hello() and uses the new RFC 5077 functionality in OpenSSL
(ssl3_check_finished) to allow the state machine handle start of
abbreviated handshake based on the used ticket.
crypto_binding=# in phase1 network parameter can now be used to change the
PEAPv0 cryptobinding behavior (0 = do not use, 1 = optional (default),
2 = required).
Explain that wpa_supplicant supports a variety of drivers, but only a
subset of them are chosen at compile time.
Signed-off-by: Kel Modderman <kel@otaku42.de>
Allow the user to set the IP address of the eapol_test client. This if
very useful when you have a machine with many interfaces and want to use a
particular one for testing RADIUS connectivity. For instance when I run the
national eduroam proxy I can only connect to other server from a particular
address, an our machine happens to have several IPs. So if I want to run
connectivity tests, I must make sure that my test uses a particular
interface. The -A option allows one to set this).
(jm: cleaned up to use radius configuration structure instead of global
variable for the address and added IPv6 support)
Implements the Chargable-User-Identity (CUI), as defined in RFC 4372.
Option "-i" causes the eapol_test to send a NUL CUI - which is a request to
send a CUI back. Capital "-I" allows to specify the value of the CUI.
This has been defined for cases where the client wants to reauthenticate.
It looks like Microsoft implementation does not match with their
specification as far as PRF+ label usage is concerned.. IPMK|CMK is derived
without null termination on the label, but the label for CSK derivation
must be null terminated.
This allows cryptobinding to be used with PEAPv0 in a way that
interoperates with Windows XP SP3 (RC2) and as such, this functionality is
now enabled as an optional addition to PEAPv0.
EAP-PEAP was the only method that used the external eap_tlv.c peer
implementation. This worked fine just for the simple protected result
notification, but extending the TLV support for cryptobinding etc. is not
trivial with such separation. With the TLV processing integrated into
eap_peap.c, all the needed information is now available for using
additional TLVs.
This adds support for PS3 wireless to wpa_supplicant.
Although PS3 wireless driver is designed to conform the WEXT standard
as much as possible, unfortunately the wext driver wrapper of
wpa_supplicant can not support PS3 wireless fully because:
- PS3 wireless driver uses private WEXT ioctls for accepting PSK of
WPA-Personal from the userland.
WEXT does not specify the way to do it.
- The association and 4-way handshake are done by PS3 virtual
wireless device. The guest OSes can not interfere it.
- No EAPOL frames are allowed to go outside of the
hypervisor/firmware nor come from. They are eaten by the firmware.
Thus I needed to make a new driver wrapper for PS3 wireless.
This patch can be applied against the latest 0.6.x tree.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
The old version was using struct wpa_sm::bssid which is not necessarily
updated to point to the correct target address when doing over-the-air FT
since the address is used before the association has actually been
completed.
When a WpaMsg item to the QValueList WpaMsgList, there's no constructor
that the QValueList can call. This is a port of the fix from the stable
branch where it builds fine.
Number of TLVs were processed in groups and these cases were now separated
into more flexible processing of one TLV at the time. wpabuf_concat()
function was added to make it easier to concatenate TLVs. EAP Sequences are
now supported in both server and peer code, but the server side is not
enabled by default.
The Debian package checker "lintian" was making noise about
wpa_supplicant.conf(5). It was caused by a line beginning with ', which is
apparently not liked by man(1).
I suggest the use of <emphasis>word</emphasis> where 'word' is used at the
moment.
Signed-off-by: Kel Modderman <kel@otaku42.de>
