This network profile parameter will be removed with the cleanup that
makes mesh use shared functions for setting channel parameters. That
will allow HT to be enabled automatically based on driver capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
Refactor the code to run tshark into its own submodule. This allows
even remembering whether -Y or -R needs to be used for filtering.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases run hostapd interface setup multiple times with
TEST_ALLOC_FAIL commands triggering memory allocation failures one by
one at each possible location in the setup sequence. Effectively, these
test cases will hit most error paths for memory allocation issue cases
(i.e., only the cases requiring more than one allocation failure in a
sequence are not covered).
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is a race condition between wlantest having received and written
the sniffer log and this test case using tshark to process it. Wait one
second before running tshark to make it less likely to get truncated
results that can result in the test case failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify error cases in bgscan module parameters. Increase learn bgscan
module coverage with parsing of the saved data and probe frequency
selection.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify correct behavior with invalid commands. In addition, allow minor
mac80211_hwsim modifications to be used to enable testing of the driver
interface to enable and disable channel switching.
Signed-off-by: Jouni Malinen <j@w1.fi>
Make sure the wmm_ac_status command reflects correctly the existing
tspecs after add_ts/del_ts commands. Add a new test to verify all tspecs
are removed on roaming (while FT is not used).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
The previous version was enabling all three stations at the same time
and left dev[1] and dev[2] competing on getting connected with dev[0]
that allowed only one pairing. This was not exactly robust and the pass
criteria depended on an extra event from either dev[1] or dev[2]. Fix
that by first connecting dev[0] and dev[1] and only after that, start
dev[2]. This allows proper validation of both the peering limit on
dev[0] and no extra event on dev[2].
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the Probe Response frame wait to time out when active
scanning is used under heavy CPU load. Make this test case more robust
by trying multiple times before declaring the scan for a hidden SSID to
have failed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This allows automated testing of the wpa_supplicant D-Bus interface. The
instance controlling wlan0 registers with D-Bus if dbus-daemon was
started successfully. This is only used in VM testing, i.e., not when
run-tests.sh is used on the host system with D-Bus running for normal
system purposes.
Signed-off-by: Jouni Malinen <j@w1.fi>
wpa_cli and hostapd_cli are not currently tested for code coverage, so
filter the files specific to those components away from the code
coverage reports. *_module_tests.c are not included in normal builds, so
drop them as well. In addition, drop the system header file (byteswap.h)
that gets somehow unnecessarily included in the reports for couple of
lines.
Signed-off-by: Jouni Malinen <j@w1.fi>
This leaves the build tree with valid wpa_supplicant object files in the
end and makes it a bit easier to do additional custom builds when
needed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, these test cases were marked as failures, but it is nicer to
mark as skipped if the kernel does not include support for mesh.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the newer dfs_radar* test cases did not allow hostapd
startup to fail. Since these require relatively recent kernel
support, mark the test cases with skip rather than fail based
on that step failing.
Signed-off-by: Jouni Malinen <j@w1.fi>
ap_ht_smps needs relatively recern kernel support, so allow it to be
skipped rather than claimed as failure, in case hostapd startup fails.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the separate builds to not include
wpa_cli/hostapd_cli in the default location. Make sure hostapd_cli gets
built for --codecov cases and update both WPACLI and HAPDCLI paths to
match the alternative location.
Signed-off-by: Jouni Malinen <j@w1.fi>
Large number of test cases will fail if hostapd fails to start as the
RADIUS server. To make this more obvious, verify that the RADIUS server
instance is running and do not even start test execution if the setup if
not work properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for the scr.addstr() operations to fail and terminate
parallel-vm.py if the number of failed test cases increased beyond what
fits on the screen.
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait for a CTRL-EVENT-REGDOM-CHANGE even before returning from
set_country() to avoid issues with test operations being executed before
all components have had chance to update their regulatory domain
information. Some of these test cases could fail under heavy load.
Signed-off-by: Jouni Malinen <j@w1.fi>
Merge partial lines together before processing them in parallel-vm.py.
This avoids issues in cases where the stdout read gets split into pieces
that do not include the full READY/PASS/FAIL/SKIP information. In
addition, strip unnecessary whitespace (mainly, '\r') from the log
lines.
Signed-off-by: Jouni Malinen <j@w1.fi>
parallel-vm.log is now written with details of test execution steps and
results. This makes it easier to debug if something goes wrong in VM
monitoring. The --debug option can be used to enable verbose debugging.
Signed-off-by: Jouni Malinen <j@w1.fi>
parallel-vm.py is now retrying failed cases once at the end of the run.
If all the failed test cases passed on the second attempt, that is noted
in the summary output. Results are also indicated as the exit value from
the run: 0 = all cases passed on first run, 1 = some cases failed once,
but everything passed after one retry, 2 = some cases failed did not
succeed at all.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds the remaining test cases that took more than 15 seconds to run
into the list of test cases to run at the beginning of the execution to
avoid these being left at the end when only some of the VMs may be
running.
Signed-off-by: Jouni Malinen <j@w1.fi>
Avoid unnecessary DATA_TEST_CONFIG calls and wlantest_cli invocations to
speed up the test cases. This drops ap_qosmap execution time from about
14 seconds to under 3 seconds.
Signed-off-by: Jouni Malinen <j@w1.fi>
