Commit graph

299 commits

Author SHA1 Message Date
Jouni Malinen
814782b9fe Allow driver wrappers to indicate maximum remain-on-channel duration 2010-04-11 19:42:37 +03:00
Jouni Malinen
17a4734dc4 Optimize post-WPS scan based on channel used during provisioning
Scan only the frequency that was used during provisioning during the
first five scans for the connection. This speeds up connection in the
most likely case where the AP remains on the same channel. If the AP is
not found after these initial scans, all channels will be scanned.
2010-04-11 19:06:42 +03:00
Jouni Malinen
86d4f806da Add ctrl_iface command for triggering a roam to a specific BSS
'wpa_cli roam <bssid>' can now be used to test roaming within an ESS
(e.g., for FT over-the-air). This command will bypass a new scan and
will select the BSS based on the specified BSSID. It is responsibility
of the caller to make sure that the target AP is in the BSS table.
This can be done, e.g., by running a scan before the roam command,
if needed.
2010-04-10 22:56:55 +03:00
Jouni Malinen
62c72d7299 FT: Process reassoc resp FT IEs when using wpa_supplicant SME 2010-03-13 21:13:18 +02:00
Jouni Malinen
207ef3fb12 Add suspend/resume notifications
wpa_supplicant can now be notified of suspend/resume events, e.g.,
from pm-action scripts. This allows wpa_supplicant to clear information
that may become invalid during a suspend operation.
2010-02-27 18:46:02 +02:00
Jouni Malinen
abd9fafab6 Standardize on a single definition of auth_alg bitfield values 2010-01-03 21:14:40 +02:00
Jouni Malinen
9ba9fa07cc Move wpa_supplicant specific scan code away from src/drivers
This fits better in wpa_supplicant/scan.c. Couple of remaining
scan_helpers.c functions are currently used in driver wrappers,
but they can likely be removed in the future.
2010-01-03 18:48:11 +02:00
Jouni Malinen
a8e0505bf0 Use driver event, EVENT_EAPOL_RX, for EAPOL frame indication 2010-01-03 17:44:40 +02:00
Jouni Malinen
8f770587d9 Maintain a pointer to the current BSS table entry 2010-01-02 16:59:19 +02:00
Jouni Malinen
a1fd2ce54e Do not store raw scan results
Use scan results to update the BSS table and to select the BSS for
connection, but do not store the results for longer time.
2010-01-02 16:41:38 +02:00
Jouni Malinen
6fa81a3b3f Use BSS table entry instead of raw scan result for connection 2010-01-02 16:16:02 +02:00
Jouni Malinen
8d923a4acf Only expire scanned BSSes based on new scan results
Get more information about scans when updating BSS table information.
This allows the missing-from-scans expiration rule to work properly
when only partial set of channels or SSIDs are being scanned.
2010-01-02 13:57:44 +02:00
Jouni Malinen
8ddef94bd4 dbus: Share common initialization code for both old and new interface
This was mostly identical code that had been copied for the new D-Bus
API implementation and as such, should really have been shared from
the beginning. In addition, the copied code ended up generating
interesting stack traces since the actual D-Bus connection was being
shared even though the pointer to it was stored in two distinct
data structures. The old D-Bus code ended up dispatching some
D-Bus callbacks which ended up running the new D-Bus code.

Since the private context pointers were mostly identical, everything
seemed to more or less work, but this design was just making things
more complex and potentially very easy to break.
2009-12-31 00:15:56 +02:00
Jouni Malinen
d009a9dac6 Add scan parameter support for client MLME 2009-12-28 13:34:03 +02:00
Jouni Malinen
4832ecd754 Add an option for driver wrappers to report operational frequency 2009-12-28 13:23:13 +02:00
Jouni Malinen
d4bf8f132a Add BSS list sorted by id and add some helper functions
This allows the BSS list to be iterated in order of increasing id
to avoid problems with new scans reordering entries. The order on the
wpa_s->bss list changes with most recently updated entries being moved
to the tail of the list while wpa_s->bss_id list maintains its order
with new entries being added to the tail and old entries being removed
when they expire.
2009-12-28 00:30:38 +02:00
Jouni Malinen
83922c2d34 Add BSS table to track scan results without dropping information
Collect information from scan results into a BSS table that will not
expire information as quickly as scan results where every new scan,
no matter for how limited set of channels/SSIDs, clears all old
information.

For now, this is only used for D-Bus BSS added/removed notifications,
but this will likely be extended to be used internally instead of the
scan results to better support partial scans.
2009-12-27 21:07:47 +02:00
Jouni Malinen
719347511a Get rid of unnecessary typedefs for enums. 2009-12-26 10:35:08 +02:00
Jouni Malinen
1a1bf008cb WPS ER: Delay wpa_supplicant termination to allow unsubscription
Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
2009-12-19 23:47:54 +02:00
Jouni Malinen
fb7842aa51 Remove struct hostapd_rate_data from driver API
In addition to the bitrate, the only other variable in this structure
is used internally in hostapd. Move this structure into hostapd.h and
make the driver API use simpler data structure (array of bitrates).
2009-12-09 21:57:50 +02:00
Jouni Malinen
127608152e Move EAP method registration away from src/eap_{peer,server}
This makes it easier to make a library out of EAP methods without
losing possiblity of binary size optimization by linker dropping
unreferenced code.
2009-12-06 11:28:41 +02:00
Jouni Malinen
8a5ab9f5e5 Fix init2() driver_ops to get the correct global driver context
Need to provide the private driver context, not the wpa_supplicant
global context, in init2() call.
2009-11-28 18:11:16 +02:00
Jouni Malinen
62fa124ce2 nl80211/SME: Use reassociation when roaming within the ESS 2009-11-17 19:25:05 +02:00
Witold Sowa
8fc2fb56e4 wpa_supplicant: new DBus API implementation
This patch implements the new DBus API. Both, the new and the
previous API may work concurrently and may be turned on or off
separately in .config file.
Some features of the new API are:
 - more wpa_supplicant's events are signaled with DBus signals,
 - introspection data (requires libxml2 and may be disabled),
 - CurrentBSS and CurrentNetwork properties,
 - PropertyChanged signal for most of properties,
 - Relatively easy to extend.
.config options for the new API are: CONFIG_CTRL_IFACE_DBUS_NEW=y and
CONFIG_CTRL_IFACE_DBUS_INTRO=y for introspection.

This commit misses couple of parts from the full implementation
(these are still under review):
- fetching all configuration parameters for learning WPS information
- scan result BSS add/remove notification (register_bss() and
  unregister_bss() notification callbacks)
2009-11-09 23:51:59 +02:00
Jouni Malinen
e9bcfebfce WPS: Add initial part of External Registrar functionality
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
2009-11-07 12:41:01 +02:00
Jouni Malinen
d27df100b5 Allow driver and ctrl_interface parameters to be overridden
New wpa_supplicant command line options -o<driver> and -O<ctrl> can
now be used to override the parameters received in add interface
command from dbus or global ctrl_interface. This can be used, e.g.,
to enable control interface when using NetworkManager (add
-O/var/run/wpa_supplicant into the Exec parameter in
/usr/share/dbus-1/system-services/fi.epitest.hostap.WPASupplicant.service).
Similarly, this can be used to use another driver wrapper with
NetworkManager (e.g., -onl80211 to replace WEXT with nl80211).
2009-11-04 20:16:15 +02:00
Sam Leffler
4f34d51abe Do not schedule a new scan if no networks are enabled
This avoids an extra timeout to move to INACTIVE state.
2009-10-14 22:05:58 +03:00
Johannes Berg
0194fedb46 driver_nl80211: Fix MLME key settings for static WEP
Current wpa_supplicant has a bug with WEP keys, it adds a zero-length
sequence counter field to netlink which the kernel doesn't accept.

Additionally, the kernel API slightly changed to accept keys only when
connected, so we need to send it the keys after that. For that to work
with shared key authentication, we also include the default WEP TX key
in the authentication command.

To upload the keys properly _after_ associating, add a new flag
WPA_DRIVER_FLAGS_SET_KEYS_AFTER_ASSOC_DONE indicating that the driver
needs the keys at that point and not earlier.
2009-09-15 10:48:30 +03:00
Jouni Malinen
60b94c9819 Add preliminary background scan and roaming module design
This allows background scanning and roaming decisions to be contained in
a single place based on a defined set of notification events which will
hopefully make it easier to experiment with roaming improvements. In
addition, this allows multiple intra-ESS roaming policies to be used
(each network configuration block can configure its own bgscan module).

The beacon loss and signal strength notifications are implemented for
the bgscan API, but the actual events are not yet available from the
driver.

The included sample bgscan module ("simple") is an example of what can
be done with the new bgscan mechanism. It requests periodic background
scans when the device remains associated with an ESS and has couple of
notes on what a more advanced bgscan module could do to optimize
background scanning and roaming. The periodic scans will cause the scan
result handler to pick a better AP if one becomes available. This bgscan
module can be taken into use by adding bgscan="simple" (or
bgscan="simple:<bgscan interval in seconds>") into the network
configuration block.
2009-09-15 00:08:24 +03:00
Witold Sowa
86b89452f6 Use shared functions for network operations and param changes
Instead of implementing these separately in various control
interface handlers, use shared functions. These add some of the
previously missing notification calls, too, for the affected areas.
2009-09-13 21:16:43 +03:00
Jouni Malinen
1ff733383f Delay processing of EAPOL frames when not associated
If an EAPOL frame is received while wpa_supplicant thinks the driver is
not associated, queue the frame for processing at the moment when the
association event is received. This is a workaround to a race condition
in receiving data frames and management events from the kernel.

The pending EAPOL frame will not be processed unless an association
event is received within 100 msec for the same BSSID.
2009-09-04 18:04:41 +03:00
Dan Williams
cb8564b1dd dbus: add 'scanning' property
When the supplicant is connected and performs a scan, it doesn't enter
WPA_SCANNING state for various reasons.  However, external programs
still need to know that the supplicant is scanning since they may not
wish to perform certain operations during a scan (as those operations
will likely fail or yield incorrect results).  Add a 'scanning' property
and signal to the supplicant dbus interface to allow clients to
synchronize better with the supplicant when it scans.

Signed-off-by: Dan Williams <dcbw@redhat.com>
2009-05-27 21:06:40 +03:00
Jouni Malinen
6caf9ca68c Share same hw_feature definitions between hostapd and wpa_supplicant 2009-04-03 19:04:20 +03:00
Jouni Malinen
2d5b792d2b Add preliminary hostapd data structure initialization for AP mode
wpa_supplicant can now initialize hostapd data structures when mode=2 is
used to set up an AP. The hostapd configuration is not yet set based on
wpa_supplicant network configuration block. In addition, the glue code
for hostapd driver_ops needs number of functions that will be needed for
AP functionality.
2009-03-26 20:37:05 +02:00
Jouni Malinen
c2a0407851 Add SME support (separate authentication and association)
This can be used, e.g., with mac80211-based Linux drivers with
nl80211. This allows over-the-air FT protocol to be used (IEEE
802.11r).

Since the nl80211 interface needed for this is very recent (added
today  into wireless-testing.git), driver_nl80211.c has backwards
compatibility code that uses WEXT for association if the kernel does
not support the new commands. This compatibility code can be
disabled by defining NO_WEXT_COMPAT. That code will also be removed
at  some point to clean up driver_nl80211.c.
2009-03-20 22:26:41 +02:00
Jouni Malinen
4ef1e644eb Determiner whether driver is wired at runtime based on capabilities
Do not use just the driver name for this since driver_ndis.c supports
both wired and wireless NDIS drivers and needs to indicate the driver
type after initialization.
2009-03-07 22:05:43 +02:00
Sam Leffler
daa70d49de Add support for wpa_supplicant syslog output
Enable for build: CFLAGS += -DCONFIG_DEBUG_SYSLOG in .config
Enable at runtime: -s on command line
2009-03-02 21:40:44 +02:00
Jouni Malinen
ba2a573c5f Rename "broadcast SSID" to "wildcard SSID"
"Wildcard SSID" is the term used in IEEE Std 802.11-2007, so it is a
better name for the zero-length SSID used in Probe Request.
2009-02-14 22:21:17 +02:00
Jouni Malinen
fc2b7ed5f3 Add extended driver scan request command: driver_ops::scan2()
This can be used to provide support for scanning multiple SSIDs at a
time to optimize scan_ssid=1 operations. In addition, Probe Request IEs
will be available to scan2() (e.g., for WPS PBC scanning).
2009-02-14 17:01:32 +02:00
Jouni Malinen
80bc75f135 New driver capability info: max number of scan SSIDs
The driver wrappers can now inform wpa_supplicant how many SSIDs can
be used in a single scan request (i.e., send multiple Probe Requests
per channel). This value is not yet used, but it can eventually be used
to allow a new scan command to specify multiple SSIDs to speed up
scan_ssid=1 operations. In addition, a warning could be printed if
scan_ssid=1 is used with a driver that does not support it
(max_scan_ssids=0).
2009-02-12 22:05:32 +02:00
Jouni Malinen
a609915233 Allow WPS APs for PIN enrollment even without Selected Registrar
Some WPS APs do not set Selected Registrar attribute to 1 properly when
using an external Registrar. Allow such an AP to be selected for PIN
registration after couple of scan runs that do not find APs marked with
Selected Registrar = 1. This allows wpa_supplicant to iterate through
all APs that advertise WPS support without delaying connection with
implementations that set Selected Registrar = 1 properly.
2009-01-23 13:10:58 +02:00
Jouni Malinen
11ef8d3578 Added initial step for IBSS RSN support
This commit adds a new build option, CONFIG_IBSS_RSN=y, that can be used
to enable RSN support for IBSS. This links in RSN Authenticator code
from hostapd and adds code for managing per-peer information for IBSS. A
new wpa_cli command or driver event can be used to request RSN
authentication with an IBSS peer. New RSN Authenticator and Supplicant
will be allocated for each peer.

The basic state machine setup code is included in this commit, but the
state machines are not properly started yet. In addition, some of the
callback functions are not yet complete.
2009-01-15 01:21:55 +02:00
Jouni Malinen
7e5ba1b916 Mark functions static if not used elsewhere and use proper prototypes 2009-01-03 20:38:42 +02:00
Jouni Malinen
ac305589a3 Added support for global driver data (shared by multiple interfaces)
Driver wrappers can now register global_init() and global_deinit()
driver_ops handlers to get a global data structure that can be shared
for all interfaces. This allows driver wrappers to initialize some
functionality (e.g., interface monitoring) before any interfaces have
been initialized.
2008-12-22 22:24:31 +02:00
Luis R. Rodriguez
6d1584905c wpa_supplicant: Add support for setting of a regulatory domain
This adds support for setting of a regulatory domain to wpa_supplicant
drivers. It also adds regulatory domain setting for the nl80211 driver.
We expect an ISO / IEC 3166 alpha2 in the wpa configuration file as a
global.
2008-12-09 22:11:14 +02:00
Jouni Malinen
116654ce24 WPS: Moved wps_context initialization into wps_supplicant.c
The wps_context data is now managed at wpa_supplicant, not EAP-WSC. This
makes wpa_supplicant design for WPS match with hostapd one and also
makes it easier configure whatever parameters and callbacks are needed
for WPS.
2008-11-28 20:32:13 +02:00
Jouni Malinen
46690a3b9b Added an optional mitigation mechanism for certain attacks against TKIP by
delaying Michael MIC error reports by a random amount of time between 0 and
60 seconds if multiple Michael MIC failures are detected with the same PTK
(i.e., the Authenticator does not rekey PTK on first failure report). This
is disabled by default and can be enabled with a build option
CONFIG_DELAYED_MIC_ERROR_REPORT=y in .config.

This may help in making a chopchop attack take much longer time by forcing
the attacker to wait 60 seconds before knowing whether a modified frame
resulted in a MIC failure.
2008-11-08 04:43:12 +02:00
Dan Williams
ec5f180a24 Add an optional set_mode() driver_ops handler for setting mode before keys
A bug just got reported as a result of this for mac80211 drivers.

https://bugzilla.redhat.com/show_bug.cgi?id=459399

The basic problem is that since taking the device down clears the keys
from the driver on many mac80211-based cards, and since the mode gets
set _after_ the keys have been set in the driver, the keys get cleared
on a mode switch and the resulting association is wrong.  The report is
about ad-hoc mode specifically, but this could happen when switching
from adhoc back to managed mode.
2008-09-29 16:45:49 +03:00
Jouni Malinen
6fc6879bd5 Re-initialize hostapd/wpa_supplicant git repository based on 0.6.3 release 2008-02-27 17:34:43 -08:00