Commit graph

91 commits

Author SHA1 Message Date
Alex Khouderchah
38b405c8f0 dbus: Expose authentication status to D-Bus
wpa_supplicant currently logs CTRL-EVENT-AUTH-FAILED errors when
authentication fails, but doesn't expose any property to the D-Bus
interface related to this.

This change adds the "AuthStatusCode" property to the interface, which
contains the IEEE 802.11 status code of the last authentication.

Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
2019-01-03 00:39:12 +02:00
Matthew Wang
80d06d0ca9 dbus: Export BSS Transition Management status
Add new Interface properties "BSSTMStatus", which carries the status of
the most recent BSS Transition Management request. This property will be
logged in UMA to measure 802.11v success.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2019-01-03 00:27:01 +02:00
Matthew Wang
2bbad1c7c9 dbus: Export roam time, roam complete, and session length
Add new Interface properties "RoamTime", "RoamComplete", and
"SessionLength". "RoamTime" carries the roam time of the most recent
roam in milliseconds. "RoamComplete" carries True or False corresponding
to the success status of the most recent roam. "SessionLength" carries
the number of milliseconds corresponding to how long the connection to
the last AP was before a roam or disconnect happened.

Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
2019-01-03 00:20:34 +02:00
Andrej Shadura
c3f23ad6c7 dbus: Expose connected stations on D-Bus
Make it possible to list connected stations in AP mode over D-Bus, along
with some of their properties: rx/tx packets, bytes, capabilities, etc.

Signed-off-by: Mathieu Trudel-Lapierre <mathieu.trudel-lapierre@canonical.com>

Rebased by Julian Andres Klode <juliank@ubuntu.com> and updated to use
the new getter API.

Further modified by Andrej Shadura to not error out when not in AP mode
and to send separate StationAdded/StationRemoved signals instead of
changing signatures of existing StaAuthorized/StaDeauthorized signals.

Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
2018-12-23 17:25:11 +02:00
Ahmed ElArabawy
45f7574d31 Propagate the EAP method error code
In the current implementation, upon an EAP method failure, followed by
an EAP failure, the EAP Status is propagated up in wpa_supplicant with a
general failure parameter string "failure". This parameter is used for a
notification on the dbus.

This commit reports the EAP method failure error code in a separate
callback.

The solution in this commit is generic to all EAP methods, and can be
used by any method that need to pass its error code. However, this
commit only implements the reporting for EAP-SIM and EAP-AKA methods
where the Notification Code (in AT_NOTIFICATION) is used as the method
specific error code value.

Signed-off-by: Ahmed ElArabawy <arabawy@google.com>
2018-03-31 11:57:33 +03:00
Saurav Babu
a9de99b1c5 dbus: Add MeshPeerDisconnected signal
This is similar to the control interface event MESH-PEER-DISCONNECTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:37 +03:00
Saurav Babu
9b0701fbf5 dbus: Add MeshPeerConnected signal
This is similar to the control interface event MESH-PEER-CONNECTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-10 01:39:35 +03:00
Saurav Babu
a39b040b4c dbus: Add MeshGroupRemoved signal
This is similar to the control interface event MESH-GROUP-REMOVED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-09 14:12:33 +03:00
Saurav Babu
89e9cd25d2 dbus: Add MeshGroupStarted signal
This introduces a new interface for mesh and adds a signal that
is similar to the control interface event MESH-GROUP-STARTED.

Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
2017-09-09 14:01:14 +03:00
Nishant Chaprana
18f1611797 D-Bus: Send P2P IP address assignment info with GroupStarted event
This commit adds IP address information into GroupStarted event on the
P2P client side like it is sent over the control interface.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2016-11-21 14:45:13 +02:00
Jouni Malinen
f4b4ddfdd9 D-Bus: Remove unused wpas_dbus_signal_p2p_group_started() parameter
The ssid pointer was not used.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-05-30 17:56:41 +03:00
Nishant Chaprana
4fe50bbc8e D-Bus: Indicate whether created group is persistent or not
This adds an extra parameter in GroupStarted signal to indicate whether
the created group is Persistent or not. It is similar to the
[PERSISTENT] tag which comes in P2P-GROUP-STARTED over the control
interface.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2016-05-30 17:56:16 +03:00
Roshan Pius
7b4bbb9f94 binder: Add binder skeletal code for Android
Create the skeletal binder interface for wpa_supplicant. The interface
hierarchy is based off the existing dbus
interface(https://w1.fi/wpa_supplicant/devel/dbus.html).

Since we use libbinder, the binder interface codebase needs to be
written in C++ and can only be compiled on Android platform for now.

The aidl files define binder RPC interfaces. The Android build system
generates the corresponding C++ interface classes which needs to be
implemented by the server process.

The clients can obtain a reference to the binder service (root object)
using:
android::String16 service_name("fi.w1.wpa_supplicant");
android::sp<android::IBinder> binder =
  android::defaultServiceManager()->getService(service_name);

Once a reference to the root object is retrieved, the clients can
obtain references to other RPC objects using that root object methods.

Signed-off-by: Roshan Pius <rpius@google.com>
2016-04-02 17:35:26 +03:00
Naveen Singh
c7fb678f31 D-Bus: Add association response status code property for failure cases
(Re)Association Response frame with status code other than 0 is now
notified over DBUS as a part of PropertiesChanged signal. This can be
used by application in case AP is denying association with status code
17 (band steering) so that it does not interfere in the BSSID selection
logic of wpa_supplicant.

Signed-off-by: Naveen Singh <nasingh@google.com>
2016-03-06 20:44:51 +02:00
Maneesh Jain
be5ab8d4ab D-Bus: Add InvitationReceived Signal
This is equivalent to the P2P_EVENT_INVITATION_RECEIVED signal on the
control interface. It can be used to sent the Invitation Received signal
to applications written using D-Bus.

Signed-off-by: Maneesh Jain <maneesh.jain@samsung.com>
2015-09-27 15:55:11 +03:00
Nishant Chaprana
2a95fac944 P2P: Add D-Bus signal GroupFormationFailure
This is similar to the control interface event
P2P-GROUP-FORMATION-FAILURE.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2015-09-05 23:01:20 +03:00
Anton Nayshtut
b36a3a65aa FST: Integration into wpa_supplicant
This commit integrates the FST into the wpa_supplicant.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Jouni Malinen
661888be39 P2P: Fix persistent group profile on manual disabled=2 change
ssid->p2p_persistent_group was left to its old value when changing a
network profile to/from P2P persistent group type (disabled=2). This
could result in unexpected behavior when using an incomplete persistent
group profile. This was mainly visible through D-Bus network profile
handling where a persistent group would not be unregistered insome
cases.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-11 00:02:05 +03:00
Avichal Agarwal
1a2f7ca1b8 D-Bus: Add WPS pbc-overlap Event
This sends an Event D-Bus signal with name "pbc-overlap" for
WPS-EVENT-OVERLAP.

Signed-off-by: Avichal Agarwal <avichal.a@samsung.com>
2015-06-10 20:51:30 +03:00
MAYANK HAARIT
aa2b12562b P2P: Add GO Intent of connecting device in GO Negotiation Request event
Add GO Intent information of connecting device in GO Negotiation Request
event which will help applications to decide its own GO intent value in
advance and can avoid failure cases when both devices use GO Intent 15
depending on application requirement.

Signed-off-by: Mayank Haarit <mayank.h@samsung.com>
2015-06-06 18:16:39 +03:00
Nishant Chaprana
7b642dc80b P2P: Add D-Bus FindStopped to notify P2P-FIND-STOPPED event
Add D-Bus notification mechanism of P2P-FIND-STOPPED event on
fi.w1.wpa_supplicant1.Interface.P2PDevice interface.

Signed-off-by: Nishant Chaprana <n.chaprana@samsung.com>
2015-05-25 18:31:09 +03:00
Jouni Malinen
5441da2beb Fix wpas_notify_network_removed()
Commit bb3df9a569 ('notify: Do not raise
any signal from a P2P management interface') was supposed to only change
D-Bus behavior, but it ended up disabling non-D-Bus functionality as
well for some sequences where the P2P Device interface is used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-29 20:51:14 +03:00
Jouni Malinen
1e529832a8 D-Bus: Fix network block type change
It is possible for a network profile to change its type from P2P
persistent group to a normal network and back. The D-Bus interface uses
different types of objects for those, so the object needs to
re-registered in case of type change. This fixes issues in leaving
behind an incorrect type of object and leaking memory when freeing such
a network block that has had its disabled parameter changed.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-07 16:19:08 +02:00
Jouni Malinen
d07d3fbda2 Add peer certificate alt subject name information to EAP events
A new "CTRL-EVENT-EAP-PEER-ALT depth=<i> <alt name>" event is now used
to provide information about server certificate chain alternative
subject names for upper layers, e.g., to make it easier to configure
constraints on the server certificate. For example:
CTRL-EVENT-EAP-PEER-ALT depth=0 DNS:server.example.com

Currently, this includes DNS, EMAIL, and URI components from the
certificates. Similar information is priovided to D-Bus Certification
signal in the new altsubject argument which is a string array of these
items.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-14 15:45:18 +02:00
Jouni Malinen
5f136bc126 D-Bus: Fix P2P persistent group removal from non-D-Bus triggers
It is possible for the persistent group object to be added and removed
by non-D-Bus triggers (e.g., ctrl_iface commands). The add part was
already handled, but removal was not. That resulted in memory leaks when
a P2P persistent group was removed without using an explicit D-Bus
command for this even if the object was added without D-Bus involvement.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-29 15:49:05 +02:00
Jouni Malinen
11973b2682 D-Bus: Fix P2P peer joined/disconnected handlers
It is possible for the peer to be a non-P2P device and as such, for
p2p_dev_addr to be NULL. This resulted in NULL pointer dereference if
D-Bus interface was enabled for the interface when a legacy STA joined a
group.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-29 15:49:05 +02:00
Tomasz Bursztyka
bb3df9a569 notify: Do not raise any signal from a P2P management interface
Such interface is not registered on DBus, thus there is no need to raise
any signal from it.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-10-27 17:15:09 +02:00
Jouni Malinen
0ef023e478 Add support for driver command to update roaming policy
The network block bssid parameter can be used to force a specific BSS to
be used for a connection. It is also possible to modify this parameter
during an association. Previously, that did not result in any
notification to the driver which was somewhat problematic with drivers
that take care of BSS selection. Add a new mechanism to allow
wpa_supplicant to provide a driver update if the bssid parameter change
for the current connection modifies roaming policy (roaming
allowed/disallowed within ESS).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-09-11 15:59:42 +03:00
Dan Williams
3bd3257a0a dbus: add BSS Age property to indicate last-seen time
"Age" is the age in seconds since the BSS was last seen, and is
emitted as a PropertyChanged signal whenever the BSS is updated
from a scan result. It also returns the correct age when queried
directly.

This property can be used to resolve issues where, if no other
properties of the BSS changed from scan results (for example,
if the BSS always had 100% signal) no D-Bus signals would be
emitted to indicate that the BSS had just been seen in the scan.

Signed-hostap: Dan Williams <dcbw@redhat.com>
2014-09-07 19:18:45 +03:00
Tomasz Bursztyka
4a0693a4d5 dbus: Declare and implement GroupFinished as for GroupStarted
First for better concistancy but also to tell about the group_object
that is getting removed, thus the client will know about it and will be
able to act accordingly.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-07-31 17:20:56 +03:00
Tomasz Bursztyka
bf035663c9 dbus: Remove GroupMember object type and use Peer instead
GroupMember is unusable in itself and all the necessary informations are
stored in Peer objects, thus replace the use of GroupMember by Peer.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2014-06-29 17:19:12 +03:00
Jouni Malinen
bd10d93891 P2P: Clean up by moving ifdef CONFIG_P2P to p2p_suppplicant.h
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-15 19:31:53 +03:00
Jouni Malinen
3d910ef497 Interworking: Prefer last added network during network selection
Previously, any network block could be used to select the BSS to connect
to when processing scan results after Interworking network selection.
This can result in somewhat unexpected network selection in cases where
credential preferences indicated that a specific network was selected,
but another network ended up getting used for the connection. While the
older networks continue to be valid, add special processing for this
initial post-interworking-connect case to get more consistent network
selection to match with the Interworking network selection result.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-25 22:37:57 +02:00
Dmitry Shmidt
6b49907665 Android: Add SSID in supplicant change event
In addition, change wpa_s->pending_bssid to wpa_s->bssid for the BSSID
value in the event.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2013-11-17 16:47:45 +02:00
Jouni Malinen
447969e034 D-Bus: Do not send network notification for all P2P groups
Previously, network added event was skipping during group formation.
However, this did not necessarily catch all cases of temporary P2P
network blocks. Check ssid->p2p_group to make this behavior more
consistent by avoiding all P2P groups.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-08-31 16:44:42 +03:00
Chengyi Zhao
8a901d750b D-Bus: Emit signal when a station is authorized or deauthorized
Add "StaAuthorized" and "StaDeauthorized" D-Bus interface in AP mode.
After enabling the AP mode of wpa_supplicant, the other process need to
get the MAC address and authorization status of every station, so
wpa_supplicant emits signal when the station is authorized or
deauthorized.

Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
2013-06-22 12:09:09 +03:00
Chris Hessing
c7a39ba4e1 Provide TLS alerts to CLI/UI over control interface
Harmonize EAP status events over control interface to provide same
functionality as existing D-Bus callback.

Signed-hostap: Chris Hessing <chris.hessing@cloudpath.net>
2013-04-23 16:46:02 +03:00
Sven Neumann
caff399250 dbus: Add getter for WPS properties
Add "WPS" property to the DBus interface that allows to
identify the active WPS method of a BSS.

Signed-hostap: Sven Neumann <s.neumann@raumfeld.com>
2012-11-03 18:38:51 +02:00
Gary Morain
0bb1e425b5 Export disconnect reason code to dbus
In the properties changed signal, added a new property
"DisconnectReason", which carries the IEEE 802.11 reason code of the
most recent disassociation or deauthentication event. The reason code is
negative if it is locally generated. The property is sent to the DBUS
immediately so as to prevent it from being coalesced with other
disconnect events.

Signed-off-by: Gary Morain <gmorain@chromium.org>
2012-06-30 16:43:50 +03:00
Paul Stewart
dd7fec1f29 wpa_supplicant: Report EAP connection progress to DBus
Send an "EAP" signal via the new DBus interface under various
conditions during EAP authentication:

  - During method selection (ACK and NAK)
  - During certificate verification
  - While sending and receiving TLS alert messages
  - EAP success and failure messages

This provides DBus callers a number of new tools:

  - The ability to probe an AP for available EAP methods
    (given an identity).
  - The ability to identify why the remote certificate was
    not verified.
  - The ability to identify why the remote peer refused
    a TLS connection.

Signed-hostap: Paul Stewart <pstew@chromium.org>
2012-06-04 21:10:01 +03:00
Eliad Peller
dbe7aa2225 P2P: Notify about disconnection only when needed
wpas_notify_state_changed() notified about disconnection when
new_state < WPA_ASSOCIATED, without checking the old state. This
results in extra processing which can be avoided by checking that
old_state was connected.

Signed-hostap: Eliad Peller <eliad@wizery.com>
intended-for: hostap-1
2012-04-01 21:49:03 +03:00
Johannes Berg
2d43d37ff2 DBus: Add ability to report probe requests
Some applications require knowing about probe requests to identify
devices. This can be the case in AP mode to see the devices before they
connect, or even in P2P mode when operating as a P2P device to identify
non-P2P peers (P2P peers are identified via PeerFound signals).

As there are typically a lot of probe requests, require that an
interested application subscribes to this signal so the bus isn't always
flooded with these notifications. The notifications in DBus are then
unicast only to that application.

A small test script is also included.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2012-04-01 21:14:48 +03:00
Jouni Malinen
0f3d578efc Remove the GPL notification from files contributed by Jouni Malinen
Remove the GPL notification text from the files that were
initially contributed by myself.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-02-11 19:39:36 +02:00
Jouni Malinen
fbdcfd577a P2P: Maintain a list of P2P Clients for persistent group on GO
Add a new persistent group network block field, p2p_client_list, to
maintain a list of P2P Clients that have connected to a persistent
group. This allows GO of a persistent group to figure out more easily
whether re-invocation of a persistent group can be used with a specific
peer device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-22 22:47:41 +02:00
Reinette Chatre
e5a359cf7e P2P: Make GO negotiation peer and group information available over D-Bus
The GO negotiation response is very cryptic at the moment. For a success
message we only know on which interface the negotiation succeeded, not
which peer. For a failure we know the interface also and a status code
(number).

It will be very useful for clients to know upon receipt of such a message
which peer the negotiation occurred with.

Now that the peer information is available and the API is changed
already, the function composing the D-Bus message might as well include
all GO negotiation information. This is done with a dict to make things
easier on clients if this result information changes down the line.

Signed-hostap: Reinette Chatre <reinette.chatre@intel.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2011-12-18 16:52:33 +02:00
Jouni Malinen
502618f7c1 P2P: Clean up group formation on network block removal
If a P2P group network block is removed for any reason (e.g., wps_cancel
command) while the interface is in group formation, remove the group
formation timeout and indicate failure immediately. Previously, this
type of operations could end up leaving the timeout running and result
in somewhat unexpected group formation failure events later.

Signed-hostap: Jouni Malinen <j@w1.fi>
2011-12-10 12:56:42 +02:00
Dan Williams
a9022616ae dbus: Implement EAP SM control request signals
Add a D-Bus signal for EAP SM requests. This signal is emitted on the
Interface object so that clients only have to listen to one object for
requests rather than to all network objects. This signal is analogous
to the socket control interface's CTRL-REQ- request.

Signed-off-by: Dan Williams <dcbw@redhat.com>
2011-10-30 12:04:24 +02:00
Jouni Malinen
8c0d3b4fc6 Fix segfault on error path if driver initialization fails
wpa_s->wpa is NULL in this case and we better not call WPA state
machine functions.
2011-10-20 21:10:22 +03:00
Jouni Malinen
d8a790b922 Flush PMKSA cache entries and invalidate EAP state on network changes
If a network configuration block is removed or modified, flush
all PMKSA cache entries that were created using that network
configuration. Similarly, invalidate EAP state (fast re-auth).

The special case for OKC on wpa_supplicant reconfiguration
(network_ctx pointer change) is now addressed as part of the
PMKSA cache flushing, so it does not need a separate mechanism
for clearing the network_ctx values in the PMKSA cache.
2011-09-07 17:46:00 +03:00
Jouni Malinen
4f525d8e5b Move peer certificate wpa_msg() calls to notify.c
This type of wpa_supplicant specific message construction does not need
to be at the EAP implementation, so better move it up to notify.c.
2011-07-05 12:40:37 +03:00