Start sharing common SAE and EAP-pwd functionality by adding a new
source code file that can be included into both. This first step is
bringing in a shared function to check whether a group is suitable.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Move the identical function used by both SAE and EAP-pwd to
src/utils/common.c to avoid duplicated implementation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This reduces timing and memory access pattern differences for an
operation that could depend on the used password.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
SPR allows us to detect OBSS overlaps and allows us to do adaptive CCA
thresholds. For this to work the AP needs to broadcast the element
first.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
According to P802.11ax/D4.0 9.4.2.238 (HE Operation element) the BSS
Color Information field is located after the HE Operation Parameters
field. Fix the ordering of the bit masks/offsets for fields in these 3+1
octets used as a single 32-bit value. With these changes, Wireshark 3.2
is able to properly parse and display Beacon frames.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
This makes it easier to upper layer components to manage operating
channels in cases where the same radio is shared for both station and AP
mode virtual interfaces.
Signed-off-by: Omer Dagan <omer.dagan@tandemg.com>
Logs involving IEEE 802.11 Status Codes output the Status Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each status code using the latter part
of the Status Code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Logs involving IEEE 802.11 Reason Codes output the Reason Code value,
but do not provide any explanation of what the value means. This change
provides a terse explanation of each Reason Code using the latter part
of the reason code #define names.
Signed-off-by: Alex Khouderchah <akhouderchah@chromium.org>
Add initial implementation of DPP-over-TCP. This adds the general TCP
encapsulation routines into the shared src/common/dpp.c implementation.
That functionality will be exposed through hostapd and wpa_supplicant in
the following commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be helpful for testing DPP2 Controller functionality (get
pkhash from Controller to Relay).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This can be used to provide configurable parameter to the global DPP
context. This initial commit introduces the msg_ctx context pointer for
wpa_msg().
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Update the version number for the build and also add the ChangeLog
entries for both hostapd and wpa_supplicant to describe main changes
between v2.7 and v2.8.
Signed-off-by: Jouni Malinen <j@w1.fi>
Explicitly verify that own and peer commit scalar/element are available
when trying to check SAE confirm message. It could have been possible to
hit a NULL pointer dereference if the peer element could not have been
parsed. (CVE-2019-9496)
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Try to avoid showing externally visible timing or memory access
differences regardless of whether the derived pwd-value is smaller than
the group prime.
This is related to CVE-2019-9494.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is an initial step towards making the FFC case use strictly
constant time operations similarly to the ECC case.
sae_test_pwd_seed_ffc() does not yet have constant time behavior,
though.
This is related to CVE-2019-9494.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These groups have significant probability of coming up with pwd-value
that is equal or greater than the prime and as such, need for going
through the PWE derivation loop multiple times. This can result in
sufficient timing different to allow an external observer to determine
how many rounds are needed and that can leak information about the used
password.
Force at least 40 loop rounds for these MODP groups similarly to the ECC
group design to mask timing. This behavior is not described in IEEE Std
802.11-2016 for SAE, but it does not result in different values (i.e.,
only different timing), so such implementation specific countermeasures
can be done without breaking interoperability with other implementation.
Note: These MODP groups 22, 23, and 24 are not considered sufficiently
strong to be used with SAE (or more or less anything else). As such,
they should never be enabled in runtime configuration for any production
use cases. These changes to introduce additional protection to mask
timing is only for completeness of implementation and not an indication
that these groups should be used.
This is related to CVE-2019-9494.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Make the non-failure path in the function proceed without branches based
on r_odd and in constant time to minimize risk of observable differences
in timing or cache use. (CVE-2019-9494)
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The QR test result can provide information about the password to an
attacker, so try to minimize differences in how the
sae_test_pwd_seed_ecc() result is used. (CVE-2019-9494)
Use heap memory for the dummy password to allow the same password length
to be used even with long passwords.
Use constant time selection functions to track the real vs. dummy
variables so that the exact same operations can be performed for both QR
test results.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Inclusion of common/dpp.h into hostapd/main.c brought in an undesired
unconditional dependency on OpenSSL header files even for builds where
DPP is not enabled. Fix this by making the dpp.h contents, and in
particular the inclusion of openssl/x509.h, conditional on CONFIG_DPP.
Fixes: 87d8435cf9 ("DPP: Common configurator/bootstrapping data management")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The rules defining which DH groups are suitable for SAE use were
accepted into IEEE 802.11 REVmd based on this document:
https://mentor.ieee.org/802.11/dcn/19/11-19-0387-02-000m-addressing-some-sae-comments.docx
Enforce those rules in production builds of wpa_supplicant and hostapd.
CONFIG_TESTING_OPTIONS=y builds can still be used to select any o the
implemented groups to maintain testing coverage.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This commit introduces an attribute
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON to carry the roam reason code
through QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Avoid duplicated code in each user of dpp_build_conf_req() by moving the
common encapsulation case into this helper function.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Merge the practically copy-pasted implementations in wpa_supplicant and
hostapd into a single shared implementation in dpp.c for managing
configurator and boostrapping information. This avoid unnecessary code
duplication and provides a convenient location for adding new global DPP
data.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The offset update for copying KEK2 from the extended PTK was overriding
the offset instead of incrementing it (a likely copy-paste error from
the first offset assignment based on KCK). This resulted in KEK2 being
set to incorrect segment of PTK. Fix this by updating the offset
properly so that KEK2 is copied from the correct place at the end of the
PTK.
Fixes: 2f37387812 ("FILS: Add more complete support for FT-FILS use cases")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use Diffie-Hellman key exchange to derivate additional material for
PMK-to-PTK derivation to get PFS. The Diffie-Hellman Parameter element
(defined in OWE RFC 8110) is used in association frames to exchange the
DH public keys. For backwards compatibility, ignore missing
request/response DH parameter and fall back to no PFS in such cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
DPP allows Diffie-Hellman exchange to be used for PFS in PTK derivation.
This requires an additional Z.x (x coordinate of the DH shared secret)
to be passed to wpa_pmk_to_ptk(). This commit adds that to the function
and updates all the callers to pass NULL,0 for that part in preparation
of the DPP specific changes to start using this.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This allows devices supporting DPP protocol version 2 or newer to
provision networks that enable both the legacy (PSK/SAE) and DPP
credentials.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Share a single parsing implementation for both hostapd and
wpa_supplicant to avoid code duplication. In addition, clean up the
implementation to be more easily extensible.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Use this new message from Enrollee to Configurator to indicate result of
the config object provisioning if both devices support protocol version
2 or newer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Send out the new Protocol Version attribute in Authentication
Request/Response messages and determine the peer version based on this
attribute.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This subcommand is used to update Zigbee state and specified WLAN
durations to enhance success ratio of Zigbee joining network. The
attributes defined in enum qca_mpta_helper_vendor_attr are used to
deliver these parameters to the driver.
Signed-off-by: stonez <stonez@codeaurora.org>
Peer rate statistics is per-peer cached data in the driver. These
statistics needs to be flushed to a user space application on
synchronous/asynchronous events. This command is used as an event from
the driver to flush per-peer cached statistics to the application.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new QCA vendor specific feature capability indication for the
device to indicate the support of TWT.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current/default behavior of set blacklist BSSID QCA vendor command
is a mandate to the driver - do not consider this BSSID for connect/roam
till reset.
There are use cases where this need not be a mandate and thus could
provide the flexibility for the driver to consider this BSSID if there
are no better ones. Such use cases can use this new flag attribute to
only hint the blacklist of a BSSID to the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do not start SAE authentication from scratch when the AP requests
anti-clogging token to be used. Instead, use the previously generated
PWE as-is if the retry is for the same AP and the same group. This saves
unnecessary processing on the station side in case the AP is under heavy
SAE authentiation load.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
According to IEEE Std 802.11-2016, 9.4.2.25 when fields of an RSNE are
not included, the default values are used. The cipher suite defaults
were hardcoded to CCMP in the previous implementation, but the default
is actually different for DMG: GCMP (per 9.4.2.25.2).
It is not possible to find out from the RSNE if the network is non-DMG
or DMG, so callers of wpa_parse_wpa_ie_rsn() need to handle this case
based on context, which can be different for each caller.
In order to fix this issue, add flags to the wpa_ie_data indicating
whether pairwise/group ciphers were included in the RSNE. Callers can
check these flags and fill in the appropriate ciphers. The
wpa_parse_wpa_ie_rsn() function still initializes the ciphers to CCMP by
default so existing callers will not break. This change also fixes some
callers which need to handle the DMG network case.
Signed-off-by: Lior David <liord@codeaurora.org>
This new QCA vendor attribute adds provision to specify the
ethernet protocol id from userspace to the packets which are
offloaded to the driver/firmware (e.g., IPv4, IPv6).
Signed-off-by: Arun Kumar Khandavalli <akhandav@codeaurora.org>
The new sae_password parameter [|vlanid=<VLAN ID>] can now be used to
assign stations to a specific VLAN based on which SAE Password
Identifier they use. This is similar to the WPA2-Enterprise case where
the RADIUS server can assign stations to different VLANs and the
WPA2-Personal case where vlanid parameter in wpa_psk_file is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Allow user space applications to check whether wlan firmware is alive
through an nl80211 vendor command.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The change is bigger because here we need to catch the error
condition if the last element doesn't fit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.
Then, add the element iteration macros
* for_each_element
* for_each_element_id
* for_each_element_extid
which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.
While at it also add
* for_each_subelement
* for_each_subelement_id
* for_each_subelement_extid
which instead of taking data/length just take an outer element
and use its data/datalen.
Also add for_each_element_completed() to determine if any of
the loops above completed, i.e., it was able to parse all of
the elements successfully and no data remained.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not use a separate enum for MBO WNM-Notification Request frame
subtype values since these share the same number space with the Hotspot
2.0 ones.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The previously used value 2 was already assigned for another purpose
(MBO non-preferred channel report), so the newer T&C Acceptable
definition needs to be updated with a unique value.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This new QCA vendor attribute indicates the EVM value in netlink.
Signed-off-by: stonez <stonez@codeaurora.org>
:100644 100644 ad5dac2... ede4fc8... M src/common/qca-vendor.h
The vendor command QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY was defined
to carry the list of avoid frequencies that aim to avoid any
interference with other coexistencies. This recommendation was followed
strictly by trying to prevent WLAN traffic on the impacted channels.
This commit refines the expectation of the interface by defining this
avoid channel list to allow minimal traffic but not heavier one. For
example, P2P may still be able to use avoid list frequencies for P2P
discovery and GO negotiation if the actual group can be set up on a not
impact channel.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support for configuring parameters for the MU EDCA Parameter Set
element per IEEE P802.11ax/D3.0.
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
Define QCA vendor command attributes to configure HE +HTC support and
HE operating mode control transmission. This is used to configure the
testbed device.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
These are not allowed in ISO C++ (and well, not really in ISO C either,
but that does not result in compiler warning without pedantic
compilation).
Since ieee802_11_common.h may end up getting pulled into C++ code for
some external interfaces, it is more convenient to keep it free of these
cases. Pull in ieee802_11_defs.h to get enum phy_type defined and move
enum chan_width to common/defs.h (which was already pulled in into
src/drivers/driver.h and src/common/ieee802_11_common.h).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
While the AP is configured to enable both FT-PSK and WPA-PSK, an HP
printer request both AKMs (copied from AP?) in Association Request
frame, but don't add MDIE and don't use FT. This results in the
connection failing.
Next in logs we see:
RSN: Trying to use FT, but MDIE not included
IE - hexdump(len=26): 30 18 01 00 00 0f ac 04 01 00 00 0f ac 04
02 00 00 0f ac 02 00 0f ac 04 00 00
This is seen with some HP and Epson printers. Work around this by
stripping FT AKM(s) when MDE is not present and there is still a non-FT
AKM available.
Signed-off-by: Janusz Dziedzic <janusz@plumewifi.com>
The Android-specific chmod and chown operations on the client socket
(for communication with wpa_supplicant) did not protect against file
replacement between the bind() and chmod()/chown() calls. If the
directory in which the client socket is created (depends a bit on the
version and platform, but /data/misc/wifi/sockets is commonly used)
allows write access to processes that are different (less privileged)
compared to the process calling wpa_ctrl_open2(), it might be possible
to delete the socket file and replace it with something else (mainly, a
symlink) before the chmod/chown operations occur. This could have
resulted in the owner or permissions of the target of that symlink being
modified.
In general, it would be safest to use a directory which has more limited
write privileges (/data/misc/wifi/sockets normally has 'wifi' group
(AID_WIFI) with write access), but if that cannot be easily changed due
to other constraints, it is better to make wpa_ctrl_open2() less likely
to enable this type of race condition between the operations.
Replace chown() with lchown() (i.e., a version that does not dereference
symlinks) and chmod() with fchmod() on the socket before the bind() call
which is also not going to dereference a symlink (whereas chmod()
would). lchown() is a standard operation, but the fchmod() on the socket
is less so (unspecified behavior in some systems). However, it seems to
work on Linux and in particular, on Android, where this code is
executed.
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds checks to common code to verify supported bandwidth options
for each channel using nl80211-provided info. No support of additional
modes is added, just additional checks. Such checks are needed because
driver/hardware can declare more strict limitations than declared in the
IEEE 802.11 standard. Without this patch hostapd might select
unsupported channel and that will fail because Linux kernel does check
channel bandwidth limitations.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
The new ieee802_11_ext_capab() and wpa_bss_ext_capab() functions can be
used to check whether a specific extended capability bit is set instead
of having to implement bit parsing separately for each need.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE P802.11-REVmd/D2.0, 9.4.2.20.7 (Beacon request) and 9.4.2.21.7
(Beacon report) add the Last Beacon Report Indication subelement to
Beacon Request and Beacon Report elements.
Add the Last Beacon Report Indication subelement to all Beacon Report
elements if the Beacon Request indicated that this subelement is
requested.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
When the frame body subelement would cause the measurement report
element to exceed the maximum element size, the frame body subelement
used to be truncated. In addition, some elements were always truncated
in order to keep the reported frame body short (e.g. RSN IE).
Alternatively, IEEE P802.11-REVmd/D2.0, 9.4.2.21.7 extension to Beacon
reporting can be used: The frame body subelement is fragmented across
multiple beacon report elements, and the reported frame body fragment ID
subelement is added.
Use beacon report fragmentation instead of truncating the frame body
as this method gives the AP a more complete information about the
reported APs.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
In 2013 or so, IFNAME=foo was prepended to at least the Unix socket
communication from wpa_supplicant to wpa_cli. This broke the (fragile)
logic that made ping/pong work more often when wpa_supplicant is busy
sending logging info to wpa_cli.
Adding check for IFNAME=foo makes this work better.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Legacy ioctl() through SIOCDEVPRIVATE are deprecated. Follow the
approach taken by bridge-utils and make use of new bridge ioctl's
whenever possible.
For example, using legacy ioctl() breaks dynamic VLAN mode on 32-bit
Linux systems running 64-bit kernels.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
An AP might refuse to connect a STA if it has a low RSSI. In such case,
the AP informs the STA with the desired RSSI delta and a retry timeout.
Any subsequent association attempt with that AP (BSS) should be avoided,
unless the RSSI level improved by the desired delta or the timeout has
expired.
Defined in Wi-Fi Alliance Optimized Connectivity Experience technical
specification v1.0, section 3.14 (RSSI-based association rejection
information).
Signed-off-by: Beni Lev <beni.lev@intel.com>
This new QCA vendor command is used to query the supported AKM suite
selectors from the driver. There has been no such capability indication
from the driver and thus the current user space has to assume the driver
to support all the AKMs. This may be the case with some drivers (e.g.,
mac80211-based ones) but there are cfg80211-based drivers that implement
SME and have constraints on which AKMs can be supported (e.g., such
drivers may need an update to support SAE AKM using
NL80211_CMD_EXTERNAL_AUTH). Allow such drivers to specify the exact set
of supported AKMs so that user space tools can determine what network
profile options should be allowed to be configured. This command returns
the list of supported AKM suite selectors in the attribute
NL80211_ATTR_AKM_SUITES.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Looks like LibreSSL 2.8 pulled in the OpenSSL API change to mark the
first argument to X509_ALGOR_get0() const.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The purpose of Multi-AP specification is to enable inter-operability
across Wi-Fi access points (APs) from different vendors.
This patch introduces one new configuration parameter 'multi_ap' to
enable Multi-AP functionality and to configure the BSS as a backhaul
and/or fronthaul BSS.
Advertise vendor specific Multi-AP capabilities in (Re)Association
Response frame, if Multi-AP functionality is enabled through the
configuration parameter.
A backhaul AP must support receiving both 3addr and 4addr frames from a
backhaul STA, so create a VLAN for it just like is done for WDS, i.e.,
by calling hostapd_set_wds_sta(). Since Multi-AP requires WPA2 (never
WEP), we can safely call hostapd_set_wds_encryption() as well and we can
reuse the entire WDS condition.
To parse the Multi-AP Extension subelement, we use get_ie(): even though
that function is meant for parsing IEs, it works for subelements.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Include an OCI element in SA Query Request and Response frames if OCV
has been negotiated.
On Linux, a kernel patch is needed to let clients correctly handle SA
Query Requests that contain an OCI element. Without this patch, the
kernel will reply to the SA Query Request itself, without verifying the
included OCI. Additionally, the SA Query Response sent by the kernel
will not include an OCI element. The correct operation of the AP does
not require a kernel patch.
Without the corresponding kernel patch, SA Query Requests sent by the
client are still valid, meaning they do include an OCI element.
Note that an AP does not require any kernel patches. In other words, SA
Query frames sent and received by the AP are properly handled, even
without a kernel patch.
As a result, the kernel patch is only required to make the client properly
process and respond to a SA Query Request from the AP. Without this
patch, the client will send a SA Query Response without an OCI element,
causing the AP to silently ignore the response and eventually disconnect
the client from the network if OCV has been negotiated to be used.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
ocv_verify_tx_params() verifies that the receive OCI element includes
field values that are compatible with the local channel configuration.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This adds two utility functions to convert both operating classes and
and the chan_width enum to an integer representing the channel
bandwidth. This can then be used to compare bandwidth parameters in an
uniform manner.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
This function can be used to easily convert the parameters returned
by the channel_info driver API, into their corresponding operating
class and channel number.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
Also add the ChangeLog entries for both hostapd and wpa_supplicant to
describe main changes between v2.6 and v2.7.
Signed-off-by: Jouni Malinen <j@w1.fi>
The reverse case (local identifier configured but no identifier
received) was already covered, but PKEX is not going to complete
successfully if there is any difference in identifier configuration, so
ignore this other case as well. This avoids unnecessary responses to
PKEX requests with identifier from a device that is ready for PKEX in
general, but not for that particular request.
Signed-off-by: Jouni Malinen <j@w1.fi>
This commit enhances QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES to
also be an event, aimed to notify the link status (EX: connected
stations status on an AP link).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
A local memory allocation failuring during GAS Comeback Response frame
generation could result in freeing the response context without removing
it from the list. This would result in dereferencing freed memory when
processing the next comeback request.
Signed-off-by: Jouni Malinen <j@w1.fi>
If local memory allocation for the GAS response failed, couple of error
paths ended up leaking some memory maintaining the state for the
exchange. Fix that by freeing the context properly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Parse the OSEN IE from the AP to determine values used in the AssocReq
instead of using hardcoded cipher suites. This is needed to be able to
set the group cipher based on AP advertisement now that two possible
options exists for this (GTK_NOT_USED in separate OSEN BSS; CCMP or
GTK_NOT_USED in shared BSS case). Furthermore, this is a step towards
allowing other ciphers than CCMP to be used with OSEN.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG vendor command
to set the priorities among different types of traffic of
WLAN/BT/Zigbee during coex scenarios.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add interface for drivers to report changes in TX/RX throughput
dynamically to user space. This information can be used by userspace
tools to tune kernel's TCP parameters in order to achieve peak
throughput. The driver may optionally provide guidance on which TCP
parameters to be configured for optimal performance along with the
values to be configured.
The TCP parameters that need to be tuned for peak performance are not
interface specific. Based on the guidance from the driver and
considering the other interfaces that may be affected with the new
configurations, a userspace tool has to choose the values to be
configured for these parameters to achieve optimal performance across
interfaces.
The throughput levels informed by the driver with this event are only
for providing guidance on TCP parameter tuning from userspace. The
driver may change the thresholds used to decide low or medium or high
throughput levels based on several parameters based on the PHY layer
capacity in the current connection, the number of packets being
dispatched per second, or the number of packets pending in queues, etc.
The throughput levels may not be consistent with the actual throughput
of the link.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure action
frame transmission in HE trigger based PPDU.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attribute to configure HE
single user PPDU transmission.
This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add a new wifi test config QCA vendor attributes to configure HE
operating mode control field bandwidth, number of spatial streams, and
UL MU disable configuration. Define a new attribute to clear the
previously set HE OM control field configuration. This is used for
testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
