Not all driver interfaces provide driver status information with the
local address, so skip the override step if the field is not available.
This is needed, e.g., with macsec_linux.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new test to check that the AP won't send frames to the client if
it tries to talk to itself.
Note that this fails until the relevant mac80211 patch is merged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These test cases seemed to have copy-paste errors where
wait_enabled=False was forgotten even though there was no additional
steps checking the AP mode startup results. This did not break the
tests, but could have resulted in slowing them down if the STAs did not
find the AP in the first scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Linux kernel commit 113f3aaa81bd ("cfg80211: Prevent regulatory
restore during STA disconnect in concurrent interfaces") broke the
regulatory clearing attempt in many test cases since
cfg80211_is_all_idle() is now returning false due to the AP interface
being up and that results in the Country IE -based regulatory
information not getting cleared back to defaults.
Work around this by stopping the AP interface first so that when the
station interface receives the disconnection, there are no other active
interfaces in the system. In addition, wait for REGDOM event for the
Country IE hint after association to avoid disconnection before the
regulatory events have been fully processed.
Signed-off-by: Jouni Malinen <j@w1.fi>
The Linux kernel commit 113f3aaa81bd ("cfg80211: Prevent regulatory
restore during STA disconnect in concurrent interfaces") broke the
regulatory clearing attempt in this test case since
cfg80211_is_all_idle() is now returning false due to the AP interface
being up and that results in the Country IE -based regulatory
information not getting cleared back to defaults.
Work around this by stopping the AP interface first so that when the
station interface receives the disconnection, there are no other active
interfaces in the system. In addition, wait for REGDOM event for the
Country IE hint after association to avoid disconnection before the
regulatory events have been fully processed.
Signed-off-by: Jouni Malinen <j@w1.fi>
cfg80211 regulatory code gets into pretty inconvenient state if it needs
to intersect regulatory domain information from multiple regulations
(country=98). The existing mechanisms in the hwsim test cases are not
able to clear that up for the following test case and this can result in
large number of failures.
It looks like country=98 case is hit frequently in WNM test cases where
a station associates with an AP that advertises a specific country code
and that station is then asked to disconnect before the REGDOM events
have been received. Avoid this by waiting for the REGDOM events for the
init=COUNTRY_IE case before disconnecting.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This adds some minimal testing for Multi-BSS connection attempts. The
part for nontransmitted BSS is limited since hostapd/mac80211 does not
yet have sufficient support for Multi-BSS in AP mode.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Perform detailed tests with OCV enabled, for both the 4-way and group
key handshakes. These tests include establishing a working connection
with OCV enabled, assuring that a STA without OCV enabled can still
connect to a STA with OCV enabled (and vice versa), verifying that
invalid OCI elements get silently ignored, verifying that missing OCI
elements are reported, and so on.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
parallel-vm.py has obsoleted this a long time ago and there is no need
to maintain two scripts for doing more or less the same thing.
Signed-off-by: Jouni Malinen <j@w1.fi>
Now that hostapd starts mandating PMF for Hotspot 2.0 Release 2
association, this test case needs some more tweaks to work. Hardcode
Hotspot 2.0 Release 1 to be used and disable PMF explicitly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The Beacon loss event was not reported anymore, so remove that as an
unnecessary step in the test case. In addition, check the key_mgmt
values explicitly.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to meet the Hotspot 2.0 Release 2 requirement for the
third station that is actually using RSN.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Match the implementation change to fix the test cases that verified a
specific Hotspot 2.0 release number indication.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a regression test case for a potential NULL pointer
dereferencing fixed in the previous commit.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This verifies that radio measurement capabilities are negotiated
correctly for the reassociation cases with and without FT.
Signed-off-by: Jouni Malinen <j@w1.fi>
There is no point in building this tarball in /tmp that is on the
ramdisk of the VM since it will go away when the VM exits.
Signed-off-by: Jouni Malinen <j@w1.fi>
The call to remove_group() may fail, in which case all following
cleanup is skipped. This may result in failing many tests since
cleanup did not complete successfully.
Fix this by calling remove_group() after other cleanup is done so
even it fails it will not affect the following tests.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Implement ECDSA signing functionality in the Python test script for
generating a valid signedConnector. This allows coverage of DPP config
object testing to be increased more easily.
Signed-off-by: Jouni Malinen <j@w1.fi>
Based on Jouni Malinen's [76055b4c6 "tests: D-Bus Get/Set Pmf"], modified
to use the correct "s" signature for the "Pmf" property.
Removed the negative test cases, because the synthesized property doens't
seem to do error checking upon being set.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
The hwsim's start.sh script spawns hostapd process using "sudo".
Since sudo forks a child process, $! holds the pid of sudo itself.
Fix that by storing the PID of the child process instead.
Since in VM "sudo" is replaced with a dummy script, pass an additional
argument to run-all.sh and start.sh scripts to indicate that they are
running inside a VM.
This is needed to fix ap_config_reload and ap_config_reload_file test
cases on some platforms where sudo is apparently not relaying the
signals properly.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
In ap_acl_deny test, the AP doesn't send probe responses during scan due
to ACL reject. As the result, dev[0] might miss the AP's Beacon frame
because the dwell time is too short. Make the test more robust and
trigger passive scan, and by that increase the probability of hearing
the AP.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
The OSU Providers List includes two providers, so there should be two
OSU_METHOD values listed just like there was two OSU_SERVER_URI URLs.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed to allow sigma_dut to enable ap_isolate=1. In addition,
verify that the two associated STAs with RSN(EAP) and OSEN cannot
exchange frames between them.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
P2P related configuration should be done on a global control interface.
This way this test can be reused also when a dedicated P2P device
interface is used.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
It looks like tshark parser was broken at some point for
wlan.mesh.config.cap which is now (tshark 2.6.3) pointing to incorrect
field (same as wlan.mesh.config.ps_protocol). This used to work with
tshark 2.2.6.
For now, assume the capability field ends up being the last octet of the
frame.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It looks like at least tshark 2.6.3 uses a different error message for
unknown display filter fields:
tshark: Neither "wlan_mgt.fixed.category_code" nor "4" are field or protocol names.
and a different status exit code (2 instead of 1).
Add a new handler for this combination to allow automatic wlan_mgt to
wlan conversion to happen.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test starts two identical APs and assumes a connection to the first
one, though it is not necessary true. Fix that by starting the second AP
only after the connection is established.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
This test case had an error that hit an unexpected disconnection. Add an
explicit check to verify that this does not happen anymore.
Signed-off-by: Jouni Malinen <j@w1.fi>
The channel configuration in CHAN_SWITCH command was incorrect. This
resulted in switching to HT40+ channel, while announcing HT40- in the
secondary channel IE. This caused a disconnection after the channel
switch. Fix that.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Verify that PMF does not end up reporting unexpected status code 30
(temporary rejection; SA Query).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This verifies that wpa_supplicant and hostapd behave consistently with
PMKSA caching when Suite B AKMs end up deriving a new PMKID from each
4-way handshake.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a regression test case for a memory leak on DPP_CONFIGURATOR_ADD
error path in dpp_keygen_configurator() when an unsupported curve is
specified.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that the automatically generated network profile is able to
connect to a non-FT network automatically after having used FT for the
first connection.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Verify that EAP-AKA' client rejects Challenge with an appended AT_KDF
and a modified AT_KDF value during KDF negotiation.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Check that the @1@ macro gets replaced correctly both when in the middle
and when in the end of the URL template.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is needed with the modified hostapd implementation to fix the
ap_hs20_terms_and_conditions* test cases.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
It is easier to understand the hostapd debug log here if each step is
noted there before starting the wpa_supplicant operation. In addition,
it looks safer to process all pending event messages between each step
to avoid running out of any buffer limits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case verifies that wpa_supplicant is able to perform CSA to a
VHT80 channel when having to move the GO due to an avoid-frequencies
driver event.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The implementation changes in hostapd FT error path handling in the
follow commit would result in ap_ft_ap_oom7 test case failing. This is
triggered partially by PMF protections and SA Query attempts, so it
looks like it is easier to split each failure case into a separate test
case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of "invalid value" tests started to fail now that mac80211_hwsim
actually accepts power save configuration. Fix these by running the same
command for more code coverage, but in a way that ignores the result of
the operation (succeeds with older kernel versions and fails with
newer).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
For testing purposes, enable TLS v1.3 in the authentication server so
that the protocol version can be controlled from wpa_supplicant side
more easily.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like OpenSSL 1.1.1 accepted the openssl_ciphers=FOO test
configuration or well, at least does not reject it like previous
versions did. For now, ignore this failure.
Signed-off-by: Jouni Malinen <j@w1.fi>
RC4-SHA cipher case ended up allowing the handshake to be started just
to fail with "no ciphers available" when trying to generate ClientHello.
Fix this by handling an EAP failure case for the RC4-SHA test step with
OpenSSL 1.1.*.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that the AP initialization failure is reported back to
wpa_supplicant also when the initialization is complete in a callback.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
time.sleep() in run_roams() is required because the target AP sets the
key once the station was associated. There are races, when the station
processes the (Re)Association Response frame AND the test suite starts
FT_DS before the AP processes its local confirmation and thus
wpa_auth_sm_event(ASSOC_FT). Therefore, the ActionFrame will be lost, as
the AP driver is missing the key.
Since this is this speed is highly synthetic, wait a few milliseconds
before roaming back.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This is a regression test for a sequence where wpa_supplicant interface
MAC address is changed externally and the ifdown-ifup sequence is
processed only after the interface has already been set UP.
Signed-off-by: Jouni Malinen <j@w1.fi>
Test the hostapd venue_url configuration parameter. In addition, fix the
previous defined gas_anqp_venue_url test case to use correct encoding of
the Venue URL ANQP-element payload (URLs were missing and Venue Number
was off-by-one).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This test case uses EAP-MSCHAPv2 within the PEAP tunnel, so verify that
the build includes support for that before running the test.
Signed-off-by: Sean Parkinson <sean@wolfssl.com>
Enable appropriate Suite B test cases with BoringSSL. Currently, this
means enabling only the 192-bit level ECDSA and ECDHE-RSA since
BoringSSL has removed support for DHE and there is no need to support
128-bit level ECDSA anymore.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
On Fedora 26, start.sh fails with these error messages.
Failed to connect to wpa_supplicant global interface: /tmp/wpas-wlan0 error: Permission denied
Failed to connect to wpa_supplicant global interface: /tmp/wpas-wlan0 error: Permission denied
...
This is because Fedora 26 uses "wheel" group as administrative group.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
This is used in the tests, too, and was already covered by the build.sh
script, but not this README file.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Clear the model_name parameter back to the default (empty string) at the
beginning and the end of dbus_set_global_properties to avoid failures if
the test case is run multiple times.
Signed-off-by: Jouni Malinen <j@w1.fi>
Ignore any unexpected deviceLost event before the peer devices has been
discovered. This works around issues where the previous test case
terminates before the D-Bus events have been fully delivered. This could
happen, e.g., when running dbus_p2p_discovery twice in a row.
Signed-off-by: Jouni Malinen <j@w1.fi>
