While the Suite B AKM is not really going to be used with CCMP-128 or
GCMP-128 cipher, this corner case could be fixed if it is useful for
some testing purposes. Allow that special case to skip the HMAC-SHA1
check based on CCMP/GCMP cipher and use the following AKM-defined check
instead.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, wowlan_triggers were updated in kernel only during startup.
Also update it whenever it is set from the control interface.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This part is missing from IEEE Std 802.11ai-2016, but the lack of DHss
here means there would not be proper PFS for the case where PMKSA
caching is used with FILS SK+PFS authentication. This was not really the
intent of the FILS design and that issue was fixed during REVmd work
with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that add DHss into FILS-Key-Data (and PTK, in practice) derivation for
the PMKSA caching case so that a unique ICK, KEK, and TK are derived
even when using the same PMK.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
with FILS SK+PFS if only STA or AP side implementation is updated.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE Std 802.11ai-2016 had missed a change in the Pairwise key hierarchy
clause (12.7.1.3 in IEEE Std 802.11-2016) and due to that, the previous
implementation ended up using HMAC-SHA-1 -based PMKID derivation. This
was not really the intent of the FILS design and that issue was fixed
during REVmd work with the changes proposed in
https://mentor.ieee.org/802.11/dcn/17/11-17-0906-04-000m-fils-fixes.docx
that change FILS cases to use HMAC-SHA-256 and HMAC-SHA-384 based on the
negotiated AKM.
Update the implementation to match the new design. This changes the
rsn_pmkid() function to take in the more generic AKMP identifier instead
of a boolean identifying whether SHA256 is used.
Note: This is not backwards compatible, i.e., this breaks PMKSA caching
based on the initial ERP key hierarchy setup if only STA or AP side
implementation is updated. PMKSA caching based on FILS authentication
exchange is not impacted by this, though.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Previously, the code that writes mesh_rssi_threshold to a network block
always executes, but the code that reads it from network block and the
code that initializes it to a default value in a new network block are
inside #ifdef CONFIG_MESH. As a result when writing a config file it
will write mesh_rssi_threshold (since it has a non-default value) and
later fail to read the network block.
Fix this by moving the write code under #ifdef CONFIG_MESH as well.
Note, network blocks which already have mesh_rssi_threshold because of
the bug will still fail to read after the fix.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
The introduction of radio works and a delayed callback to complete
association/connection requests ended up breaking RSN pre-authentication
candidate list generation for the case of pre-connection scan results.
Previously, wpa_supplicant_associate() set the RSN state machine
configuration before returning and the calls to
wpa_supplicant_rsn_preauth_scan_results() immediately after this
function call were working fine. However, with the radio work callback,
the RSN state machine configuration started to happen only in that
callback which would be called soon after this code path has completed.
This resulted in the RSN state machine not knowing the selected SSID and
as such, rejecting all pre-authentication candidates.
Fix this by setting the RSN state machine configuration from
wpa_supplicant_associate() so that the existing callers of
wpa_supplicant_rsn_preauth_scan_results() can be used as-is to add
candidates for pre-authentication.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
secy_init_macsec() can fail (if ->macsec_init fails), and
ieee802_1x_kay_init() should handle this and not let MKA run any
further, because nothing is going to work anyway.
On failure, ieee802_1x_kay_init() must deinit its kay, which will free
kay->ctx, so ieee802_1x_kay_init callers (only ieee802_1x_alloc_kay_sm)
must not do it. Before this patch there is a double-free of the ctx
argument when ieee802_1x_kay_deinit() was called.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
When building wpa_ie in wpas_start_assoc_cb() with ext_capab,
make sure that assignment does not exceed max_wpa_ie_len.
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
Removing interface from bridge in_br
linux_br_del_if(drv->global->ioctl_sock, in_br, ifname)
but in case of failure, the error print is incorrect:
it should show error for "in_br" instead of the wrong bridge name
"brname".
Signed-off-by: Rohit Pratap Singh <rohit.s@samsung.com>
Signed-off-by: Amit Khatri <amit.khatri@samsung.com>
The STA can get disconnected event before the AP processed the
deauthentication frame, resulting in GET_FAIL command being sent too
early. Fix this by waiting for AP-STA-DISCONNECTED on AP side, too.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Import vht_supported from test_ap_vht to fix the following issue:
rrm_beacon_req_table_vht run failed: global name 'vht_supported' is not defined
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
ubsan reported:
../src/crypto/random.c:69:30: runtime error: shift exponent 32 is too large for 32-bit type 'unsigned int'
Explicitly check for the ROL32(x, 0) case which is supposed to be a
no-op.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
After KDF negotiation, must check only requested change occurred in the
list of AT_KDF attributes. If there are any other changes, the peer must
behave like the case that AT_MAC had been incorrect and authentication
is failed. These are defined in EAP-AKA' specification RFC 5448, Section
3.2.
Add a complete check of AT_KDF attributes and send Client-Error if a
change which is not requested is included in it.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sony.com>
AT_KDF attributes need to be included in Synchronization-Failure
according to EAP-AKA' specification RFC 5448.
Signed-off-by: Tomoharu Hatano <tomoharu.hatano@sony.com>
pmksa_cache_add_entry() may actually free old_entry if the PMKSA cache
is full. This can result in the PMKSA cache containing entries with
corrupt expiration times.
Signed-off-by: Andrew Elble <aweits@rit.edu>
This introduces a new interface for mesh and adds a signal that
is similar to the control interface event MESH-GROUP-STARTED.
Signed-off-by: Saurav Babu <saurav.babu@samsung.com>
The "FILS: No pending HLP DHCP exchange with hw_addr" debug message was
missing a space before the following MAC address, so add that there to
make the message more readable.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It looks like these parameters related to FT have never been used, so
remove them from causing confusion. The separate update_ft_ies()
callback is used to provide the FT elements.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it easier to post-process frame capture files if frames need
to be decrypted in test cases that do not configure wlantest with the
PMK directly (i.e., mainly the cases when a RADIUS server is used).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Try to derive PTK when FILS shared key authentication is used without
PFS. The list of available PMKs is interpreted as rMSK for this purpose
and PMK and PTK is derived from that. If the resulting PTK (KEK) can be
used to decrypt the encrypted parts of (Re)Association Request/Response
frames, mark the PTK as derived so that encrypted frames during the
association can be decrypted. In addition, write a decrypted version of
the (Re)Association Request/Response frames into the output file.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new "SET sae_commit_override <hexdump>" control interface command
can be used to force wpa_supplicant to override SAE commit message
fields for testing purposes. This is included only in
CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The new sae_commit_override=<hexdump> parameter can be used to force
hostapd to override SAE commit message fields for testing purposes. This
is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Allow hostapd to be configured to perform SAE reflection attack for SAE
testing purposes with sae_reflection_attack=1 configuration parameter.
This is included only in CONFIG_TESTING_OPTIONS=y builds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Add PMKID into EAPOL-Key 1/4 when using SAE and fix the PMK-from-PMKSA
selection in some cases where PSK (from passphrase) could have been
used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This was previously defined inconsistently (H() vs. SHA256()), but it is
now clarified in the draft tech spec to use SHA256(), so update
implementation to do that.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
NL80211_ATTR_AUTH_TYPE needs to be skipped if multiple auth_alg options
are included. The previous list missed the new FILS auth_alg here and
ended up not doing so if OPEN and FILS were included.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
