When WMM is disabled, HT/VHT/HE capabilities should not be used for any
STA. If any STA advertises these capabilities, hostapd AP disables HT
capabilities in STA flags during STA assoc, but VHT/HE was not handled
similarly. This could allow a STA to associate in VHT/HE mode even in
WMM disable case.
To avoid this, disable VHT/HE capabilities similarly to HT during STA
association, if WMM is not enabled by the STA.
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Extend SPR element to support following fields and pass all
information to kernel for driver use.
* Non-SRG OBSS PD Max Offset
* SRG BSS Color Bitmap
* SRG Partial BSSID Bitmap
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Enable user to configure Maximum MPDU Length, Maximum A-MPDU Length
Exponent, Rx Antenna Pattern Consistency, and Tx Antenna Pattern
Consistency of 6 GHz capability through config file.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Add the ability to disable HT/VHT/HE for specific BSS from hostapd.conf.
- Add disable_11ax boolean to hostapd_bss_config.
- Change disable_11n and disable_11ac to bool in hostapd_bss_config.
- Add configuration option to set these disable_11* parameters
(which were previously used only automatically based on incompatible
security parameters to disable HT/VHT).
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Previously, 6 GHz Band Capability element was derived from HT and VHT
capabilities of the device. Removes such unnecessary dependency by
relying directly on the HE capability.
In addition, clean up the struct ieee80211_he_6ghz_band_cap definition
to use a 16-bit little endian field instead of two 8-bit fields to match
the definition in P802.11ax.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Process HE 6 GHz band capabilities in (Re)Association Request frames and
pass the information to the driver.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Construct HE 6 GHz Band Capabilities element (IEEE 802.11ax/D6.0,
9.4.2.261) from HT and VHT capabilities and add it to Beacon, Probe
Response, and (Re)Association Response frames when operating on the 6
GHz band.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
mode->he_capab is an array and as such, there is no point in checking
whether it is NULL since that cannot be the case. Check for the
he_supported flag instead. In addition, convert the TWT responder
capability bit into a fixed value 1 to avoid any surprising to the
callers. In practice, neither of these changes results in different
behavior in the current implementation, but this is more robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
The HE Operation field for BSS color consists of a disabled, a partial,
and 6 color bits. The original commit adding support for BSS color
considered this to be a u8. This commit changes this to the actual
bits/values.
This adds an explicit config parameter for the partial bit. The disabled
is set to 0 implicitly if a bss_color is defined.
Interoperability testing showed that stations will require a BSS color
to be set even if the feature is disabled. Hence the default color is 1
when none is defined inside the config file.
Signed-off-by: John Crispin <john@phrozen.org>
The Channel Width field value is 0 for 20 MHz, 1 for 40 MHz, 2 for 80
MHz, and 3 for both 160 MHz and 80+80 MHz channels. The 80+80 MHz case
was not addressed previously correctly since it cannot be derived from
seg0 only.
The Channel Center Frequency Segment 0 field value is the index of
channel center frequency for 20 MHz, 40 MHz, and 80 MHz channels. The
value is the center frequency index of the primary 80 MHz segment for
160 MHz and 80+80 MHz channels.
The Channel Center Frequency Segment 1 field value is zero for 20 MHz,
40 MHz, and 80 MHz channels. The value is the index of the channel
center frequency for 160 MHz channel and the center frequency index of
the secondary 80 MHz segment for 80+80 MHz channels.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When operating on the 6 GHz band, add 6 GHz Operation Information inside
the HE Operation element and don't publish HT/VHT IEs.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
- Replace HOSTAPD_MODE_IEEE80211AX mode checks with is_6ghz_op_class()
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Set the max value of optional bytes inside the data structure. This
requires us to calculate the actually used size when copying the
HE capabilities and generating the IE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
The HE capabilities are no longer per PHY but per iftype on this
specific PHY. It is therefore no longer enough to just parse the AP
capabilities.
The he_capabilities are now duplicated to store all information for
IEEE80211_MODE_* which hostap cares about. The nl80211 driver fills in
this information when the iftype supports HE. The rest of the code still
only uses the IEEE80211_HE_AP portion but can be extended later to also
use other HE capabilities.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
The the mask for PPE threshold present in the HE phy capability byte 6 is
0x80 and not 0x6. This incorrect mask breaks the length calculation and as
result the acceptance of the HE capabilities for STAs which either:
* don't have the PPE threshold present bit set AND the Codebook Size={7,5}
MU Feedback or the Triggered SU Beamforming feedback bit set
* do have the PPE threshold present set AND neither the Codebook Size={7,5}
MU Feedback nor the Triggered SU Beamforming feedback bit set
Fixes: 8f5fc369e2 ("HE: Fix HE Capabilities element variable length encoding")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Add a config option to allow setting a custom Basic NSS/MCS set. As a
default we use single stream HE-MCS 0-7.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Process HE information in (Re)Association Request frames and add HE
elements into (Re)Association Response frames when HE is enabled in the
BSS.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The HE Capibilities element has dynamic size due to the variable length
and optional fields at the end. Mask out the channel width capabilities
that are less than the configured. Only add the MCS/NSS sets for the
announced channel widths and also add the PPET elements.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
These bits might be set by the capabilities read from the kernel, so
mask them out if beamforming is not enabled in the local configuration.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
If none of the sr_control bits are set, we do not neet to add the IE to
the Beacon frame.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
The first four octets of the element were used as a host byte order u32.
That is not correct on bigendian CPUs, so handle byte swapping needs
properly. Mark the he_oper_params field as le32 to explicitly indicate
the byte order and swap the generated params content based on CPU byte
order.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
The current code will always use the size required when all optional
elements are present. This will cause the Linux kernel to consider the
field to be malformed if the elements are not actually flagged as being
present.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
SPR allows us to detect OBSS overlaps and allows us to do adaptive CCA
thresholds. For this to work the AP needs to broadcast the element
first.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Properly populate the the HE Capabilities element with the info read
from the kernel.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
According to P802.11ax/D4.0 9.4.2.238 (HE Operation element) the BSS
Color Information field is located after the HE Operation Parameters
field. Fix the ordering of the bit masks/offsets for fields in these 3+1
octets used as a single 32-bit value. With these changes, Wireshark 3.2
is able to properly parse and display Beacon frames.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Add support for configuring parameters for the MU EDCA Parameter Set
element per IEEE P802.11ax/D3.0.
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
Replace vendor-specific elements for HE capabilities and HE operation
elements with the P802.11ax defined element values. This version is
based on P802.11ax/D1.4.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
IEEE 802.11ax HE changes to include HE IEs in Beacon and Probe Response
frames. These elements are using vendor specific forms for now since the
IEEE 802.11ax draft is not yet finalized and the element contents is
subject to change.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Lavanya Suresh