Commit graph

175 commits

Author SHA1 Message Date
Jouni Malinen
faebdeaa9e Use os_calloc() instead of os_zalloc()
Automatic changes with spatch using the following semantic patch:

@@
constant C;
type T;
@@

- os_zalloc(C*sizeof(T))
+ os_calloc(C,sizeof(T))

@@
expression E;
type T;
@@

- os_zalloc((E)*sizeof(T))
+ os_calloc(E,sizeof(T))

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-08 11:42:07 +02:00
Dmitry Shmidt
d10792199e Add CTRL-EVENT-SCAN-FAILED notification in case of scan failure
This is needed since the SCAN command with radio work returns before the
actual driver operation to trigger a scan has been executed and as such,
cannot return result of that operation.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-11-15 11:03:52 +02:00
Sunil Dutt
e7ce540239 P2P: Delay scan operation only when P2P is not in search state
With the radio work interface in place, station interface SCAN command
was not scheduled (i.e., it got continously delayed with "Delay station
mode scan while P2P operation is in progress") when a p2p_find was
operational. Fix this be delaying station mode scan only when a P2P
operation is in progress, but not in search state.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-10-31 00:49:14 +02:00
Jason Abele
fbca4c893d mesh: Implement mesh scanning
When mesh is configured in, include the wildcard mesh id so that mesh
networks are returned.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Abele <jason.abele@gmail.com>
2014-10-25 17:45:35 +03:00
Jouni Malinen
c267753ba2 Add support for using random local MAC address
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.

This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.

This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.

The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 20:07:19 +03:00
Bojan Prtvar
1cc0d6a0eb wpa_supplicant: Use freq_list scan filtar in sched_scan
Global freq_list scan filtar was taken into account only by
req_scan and not by req_sched_scan. We want to allow the user
to limit the channels that wpa_supplicant will scan in req_sched_scan
requests as well.

Signed-off-by: Bojan Prtvar <bojan.prtvar@rt-rk.com>
2014-08-12 16:44:04 +03:00
Dmitry Shmidt
4ed3492206 PNO: Send Probe Request frames only for hidden SSIDs
Previously, offloaded scanning (PNO) on Android was including SSIDs from
all enabled networks regardless of the scan_ssid parameter which
resulted in different behavior for the offloaded case when comparing to
wpa_supplicant initiated scans.

Use the sched_scan match filter to allow broadcast SSID to be used for
scan_ssid=1 networks also with PNO to avoid running active scans for
SSIDs that have not been explicitly marked as requiring an SSID-specific
scan. This reduces exposure of configured network names on the device
when running offloaded scans while the host device is in sleep.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-07-03 16:44:43 +03:00
Li Jianyun
6891f0e6f4 Allow SCAN command to specify scan_ssid=1 SSIDs
The new "scan_id=<comma separated list of network ids>" parameter can
now be used to specify a list of network ids that have scan_ssid=1 to
indicate active scanning of the SSID. This adds the listed SSIDs to the
scan command to allow manual scan requests to perform active scans for
hidden SSIDs. For example, "SCAN scan_id=1,7,11" would run a scan with
the SSID fetched from the configured network blocks 1, 7, and 11
(assuming those are set with scan_ssid=1). The SSIDs will be included
even from network blocks that are currently disabled.

The maximum number of SSIDs added to the request is limited by the
driver support. If more than supported values are specified, the command
will fail (returns "FAIL").

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-07-02 12:52:08 +03:00
Johannes Berg
57a8f8af38 nl80211: Use low-priority scan for OBSS scan
Some drivers may support low-priority scans, if they do then
use that for OBSS scanning.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-06-22 00:47:06 +03:00
Jouni Malinen
bd10d93891 P2P: Clean up by moving ifdef CONFIG_P2P to p2p_suppplicant.h
This removes number of unnecessary #ifdef CONFIG_P2P blocks from generic
code by hiding the conditional build into p2p_supplicant.h with empty
inline functions.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-15 19:31:53 +03:00
Rashmi Ramanna
28fa4eb2b2 P2P: Fix scan optimization for GO during persistent group invocation
Commit 41d5ce9e0b was intended to scan for
GO on the negotiated channel for few iterations, but it did not work
correctly due to incorrect operator being used. Fix this by requiring
both conditions to be met for the single channel scan.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-13 15:49:06 +03:00
Sunil Dutt
8235f89f3f P2P: Mark the scan in p2p_in_invitation as p2p_probe
Mark the scan performed by the P2P Client in search of the GO
during the persistant reinvocation as a p2p_probe to avoid
unnecessary use of 802.11b rates.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-10 19:54:36 +03:00
Rashmi Ramanna
41d5ce9e0b P2P: Optimize scan for GO during persistent group invocation
Scan for GO on the negotiated operating channel for few iterations
before searching on all the supported channels during persistent group
reinvocation. In addition, use the already known SSID of the group in
the scans. These optimizations reduce group formation time.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-25 15:38:33 +02:00
Dmitry Shmidt
d3c9c35f32 Add freq= parameter to 'set pno' command
This allows channels-to-be-scanned to be specified for PNO similarly to
the scan command.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-03-21 23:56:46 +02:00
Peter Qiu
0f44ec8eba Add a reattach command for fast reassociate-back-to-same-BSS
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.

Signed-hostap: Peter Qiu <zqiu@chromium.org>
2014-03-11 19:38:01 +02:00
Alexander Bondar
5e3ddf4d23 PNO: Change sched_scan_stopped event to handle pending PNO properly
When a sched_scan_stopped event is received and there is a pending PNO,
it used regular scheduled scan parameters instead of PNO specific
parameters. Change it by calling wpas_start_pno().

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-11 19:15:48 +02:00
Alexander Bondar
737e7a08b0 PNO: Move and rename pno_start()/pno_stop()
Move pno_start() and pno_stop() to scan.c as a more relevant location
and rename them to wpas_start_pno()/wpas_stop_pno().

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-11 19:12:57 +02:00
Jouni Malinen
95a3ea9426 HS 2.0R2: Add WNM-Notification Request for Subscription Remediation
Subscription remediation notification WNM-Notification Request is now
shown in the following way in wpa_supplicant control interface:
<3>HS20-SUBSCRIPTION-REMEDIATION http://example.com/foo/

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
f9cd147d6b HS 2.0R2: Update Indication element to Release 2
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).

The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:22 +02:00
Andrei Otcheretianski
b3253ebb73 wpa_supplicant: Complete radio works on disable event
While testing rfkill blocking of a scanning interface, it
was seen that the ongoing scan never completes. This happens
since EVENT_SCAN_RESULTS is discarded on a disabled interface.

Fix this and also other possible radio work completion issues
by removing all the radio works (including started) of the
disabled interface.

To be able to remove already started radio works, make their
callbacks be reentrant with deinit flag (when the work
is started), so each radio work should be able to handle
its own termination.

Signed-hostap: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2014-02-16 00:06:23 +02:00
Eytan Lifshitz
fd67275b85 wpa_supplicant: Fix wrong size memory allocation
Fix memory allocation in wpa_scan_clone_params(), where the
allocation request used the size of a pointer rather than the
size of the structure.

Signed-hostap: Eytan Lifshitz <eytan.lifshitz@intel.com>
2014-01-30 13:59:29 +02:00
Raja Mani
cf70d2981d wpa_supplicant: Schedule PNO on completion of ongoing sched_scan
When start PNO request comes from control interface, wpa_supplicant
should wait until ongoing sched_scan (triggered by wpa_supplicant)
gets cancelled. Issuing cancel sched_scan and start PNO scan
one after another from pno_start() would lead wpa_supplicant to clear
wps->sched_scanning flag while getting sched_scan stopped event
from driver for cancel sched_scan request. In fact, PNO scan will
be in progress in driver and wpa_s->sched_scanning will not be set
in such cases.

In addition to this change, RSSI threshold limit is passed as part of
start sched_scan request. This was previously set only in pno_start(),
but the same parameter should be available for generic sched_scan calls
as well and this can now be reached through the new PNO start sequence.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-22 19:41:45 +02:00
Raja Mani
dd271857a5 Skip normal scan when PNO is already in progress
Scan request failures are observed in wpa_supplicant debug log when
Android framework starts PNO scan in driver via ctrl interface command
'set pno 1' and wpa_supplicant also tries to issue a scan request after
PNO has started in the driver.

Some drivers may reject a normal scan request when PNO is already in
progress. wpa_supplicant should consider PNO status before issuing start
scan request to the driver. Otherwise, wpa_supplicant will get failures
from driver for the scan request and it will end up rescheduling scan
request in periodic interval and get a start scan request failure for
each attempt.

In order to avoid unnecessary scan attempt when PNO scan is already
running, PNO status is checked before issuing scan request to driver.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-01-21 16:19:49 +02:00
Jouni Malinen
a09ffd5f2f Fix req_scan-deplete-timeout and update eloop API for this
Commit e2f5a9889a was supposed to prevent
new scan request from pushing out the old one. However, it did not
really do that since eloop_deplete_timeout() returned 0 both for the
case where the old timeout existed (and was sooner) and if the old
timeout did not exist. It returned 1 only for the case where an old
timeout did exist and was larger than the new requested value. That case
used to result in wpa_supplicant_req_scan() rescheduling the timeout,
but hew code in eloop_deplete_timeout() did the exact same thing and as
such, did not really change anything apart from the debug log message.

Extend the eloop_deplete_timeout() (and eloop_replenish_timeout() for
that matter since it is very similar) to return three different values
based on whether the timeout existed or not and if yes, whether it was
modified. This allows wpa_supplicant_req_scan() to schedule a new
timeout only in the case there was no old timeout.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
6428d0a71f Do not start wpa_radio work during externally triggered scan
If an external program triggers a scan, wpa_supplicant does not have a
wpa_radio work item for this operation to protect against other
offchannel operations. This can result in operations failing, so try to
avoid damage by not starting any new wpa_radio work items during a scan
that was started by another process.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
6470f471e4 Remove unneeded scan delay on connection-in-progress
This type of protection against concurrent connection and scan
operations is now enforced through the wpa_radio work mechanism, so this
separate protection mechanism is not needed anymore.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
b9e6d7001d Use radio work for GAS requests
Avoid concurrent GAS operations with any other exclusive use of the
radio by using the radio work queuing mechanism. This replaces some of
the earlier constraints on concurrent operations with the more generic
wpa_radio work concept.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
1b5d4714dd Use radio work for P2P scan requests
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:39:25 +02:00
Jouni Malinen
d12a51b5d2 Use radio work for scan requests
Avoid concurrent scan requests by using the radio work queuing
mechanism.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:37:50 +02:00
Jouni Malinen
dd43aaa509 Add helper functions for cloning and freeing scan parameters
Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:35:52 +02:00
Jouni Malinen
9b850799c1 Fix scan-cache-clearing operation to avoid unnecessary cases
wpa_drv_scan() success case was supposed to clear
wpa_s->clear_driver_scan_cache, not params->only_new_results (which
would do nothing here).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-03 08:55:51 +02:00
Jouni Malinen
949938aadf Ask driver to report only new scan results if requested
If the BSS table within wpa_supplicant is flushed, request the driver to
flush its own scan result table during the next scan. This can avoid
unexpected old BSS entries showing up after BSS_FLUSH or FLUSH command
in cases where the driver may maintain its internal cache of scan
results (e.g., cfg80211 BSS table persists at least for 15 seconds).

In addition to doing this automatically on BSS_FLUSH/FLUSH, a new SCAN
command argument, only_new=1, can be used to request a manual scan
request to do same. Though, it should be noted that this maintains the
BSS table within wpa_supplicant. BSS_FLUSH followed by SCAN command can
be used to clear all BSS entries from both the driver and
wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-02 23:03:31 +02:00
Jouni Malinen
3187fd900d WPS: Replace wpas_wps_in_progress with identical wpas_wps_searching
There is no point in maintaining two different functions that do
practically the same check of WPS state.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-29 17:59:12 +02:00
Jouni Malinen
662b40b16b WPS: Reduce scan wait time during WPS processing
Since the AP is expected to be available, there is no need to wait for
the full five second wait between scans during WPS connection. This
speeds up cases where the first scan misses the AP for some reason.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-12-26 20:50:28 +02:00
Jouni Malinen
1cd93ff743 Reschedule own scan request if an externally started one is in progress
This avoids some unnecessary attempts to request the driver to start a
scan while it is still busy with the scan operation that was started by
an external program.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:48:52 +02:00
Jouni Malinen
d81c73be18 Optional scan id for ctrl_iface SCAN requests
This allows users of wpa_supplicant control interface to figure out when
their specific scan command has been started and completed. For example:

CTRL-EVENT-SCAN-STARTED
> scan freq=2412,2417 passive=1 use_id=1
3
CTRL-EVENT-SCAN-RESULTS
CTRL-EVENT-SCAN-STARTED id=3
CTRL-EVENT-SCAN-RESULTS id=3

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:48:52 +02:00
Jouni Malinen
a5f40eff18 Track whether scan was started by us or an external program
This can be used to improve scan behavior in cases external programs
request scans directly from the driver.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:27:48 +02:00
Jouni Malinen
88c2d48860 Allow passive scan to be requested with SCAN passive=1
This allows external programs to request wpa_supplicant to execute
a passive scan (i.e., do not send any Probe Request frames).

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 18:27:48 +02:00
Jouni Malinen
fee5234284 Allow channel list to be specified for SCAN command
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 16:55:44 +02:00
Jouni Malinen
98eda9c26d Move int_array helpfer functions to utils/common.c
These can be useful outside scan.c, so make them available.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 13:37:06 +02:00
Johannes Berg
acb69cec6f wpa_supplicant: Use monotonic time for RX/BSS times
The BSS table, scan timeout, and related functionality should use
monotonic time since they care about relative values (age) only.
Unfortunately, these are all connected, so the patch can't be split
further. Another problem with this is that it changes the driver wrapper
API. Though, it seems only the test driver is using this.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:27:02 +02:00
Loic Poulain
1245503188 Restore scan_req if sta scan is rescheduled in the scan results event
On scan results event if a concurrent P2P scan was triggered previously,
scan results processing is canceled, p2p_find executed, and a new sta
scan is triggered (pending scan). However, this new sta scan does not
restore the scan_req value of the previous scan (whose scan result has
been canceled).

If we are currently connected to an AP and use ap_scan=2, the new
triggered scan will cause an associtation-without-scan in
wpa_supplicant_scan:
(ap_scan == 2 & scan_req != MANUAL_SCAN_REQ)
	=> wpa_supplicant_assoc_try()
causing an association error and a disconnection.

This patch fixes this issue by restoring the previous scan_req value.

Signed-off-by: Loic Poulain <loicx.poulain@intel.com>
2013-11-24 11:47:30 +02:00
Johannes Berg
594516b4c2 Use monotonic clock for relative time for eloop if available
Relative time shouldn't be calculated based on gettimeofday
because that clock can jump (e.g., when the time is adjusted
by the system administrator.)

On systems where that is available, use CLOCK_BOOTTIME (on
fairly recent Linux systems, this clock takes into account
the time spend suspended) or CLOCK_MONOTONIC (on Linux and
some POSIX systems, this clock is just freely running with
no adjustments.)

Reported-by: Holger Schurig <holgerschurig@gmail.com>
Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-11-20 23:52:56 +02:00
Jithu Jance
f86d282f43 Handle legacy scan interruption of sched_scan/PNO
While starting from PNO start context, the scheduled scan was not
setting the flag wpa_s->scanning. This was resulting in the subsequent
SCAN command to proceed further and send command to nl80211/cfg80211.
The expected behavior of cancelling sched_scan was not happening here.

While sched_scan is in progress and a legacy scan comes on the
cli/socket, the sched_scan is cancelled and normal scan is allowed to
continue. However, sometimes sched_scan cancelled event comes a bit
delayed and we will send out the scan command before the wpa_s->scanning
is cleared. Instead, reschedule the incoming scan req if the
wpa_s->scanning shows that it is still in progress.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2013-11-18 14:35:48 +02:00
Jouni Malinen
fa58da2e6c Remove old mechanism of skipping scan request rescheduling
Since eloop_deplete_timeout() is doing practically same in
wpa_supplicant_req_scan(), revert the old mechanism from commit
7e1488494e to avoid unnecessary work in
this function.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-17 16:47:13 +02:00
Dmitry Shmidt
e2f5a9889a Deplete scan request if new time is less than remaining
This avoids pushing out previous scheduled scan requests based on new
events.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2013-11-17 16:46:58 +02:00
Jouni Malinen
9100b6607b P2P: Debug print reason for specific SSID for scan
It can be useful to see whether the specific P2P SSID was used for scan
based on p2p_in_provisioning or show_group_started when debugging issues
where this case shows up unexpectedly.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-01 10:30:50 +02:00
Pontus Fuchs
c6f5dec9c1 Don't start second scan when changing scan interval
If a scan is currently running and the scan interval is changed, a
second scan will be started before the current has finished. This will
in turn, if no networks are configured, cause wpa_s->state to be
forced to WPA_INACTIVE before the first scan has finished.

Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
2013-10-22 15:57:21 +03:00
Jouni Malinen
cbc5484892 GAS: Do not start new scan operation during an ongoing GAS query
These operations can have conflicting offchannel requirements, so wait
with a new scan trigger until a pending GAS query has been completed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-21 13:20:38 +03:00
Kyeyoon Park
c377514337 GAS: Delay GAS query Tx while scanning/connecting
Offchannel operations needed for a GAS query can conflict with ongoing
scan/connection progress, so delay GAS queries if such an operation is
in progress on the current interface or any virtual interface sharing
the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-21 13:15:45 +03:00