This verifies processing of various ARP messages at an AP that enables
ProxyARP. All the validation steps have not yet been scripted, i.e., the
sniffer traces need manual analysis for full coverage.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This increases wpa_supplicant_ie_txt(), print_bss_info(), and
wpa_supplicant_ctrl_iface_scan_result() testing coverage to include the
previously missing key management options.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more convenient and consistent to clear the cached scan
results from cfg80211 and wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is more robust and extensible than configuring IPv6 addresses on
the interfaces and trying to use ping6 or some other external tools to
generate suitable IPv6 frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use scan_for_bss() instead of scan() to avoid errors if the active scan
fails, e.g., due to heavy load under parallel-vm.sh test run.
Signed-off-by: Jouni Malinen <j@w1.fi>
It looks like mac80211 scan-while-associated can now take over 10
seconds with the current wireless-regdb rules for world roaming due to
number of additional DFS channel having been enabled for passive
scanning. This resulted in ap_hs20_session_info failing due to the wait
for the scan result event timing out. That is not really a real failure,
so increase the timeout to avoid reporting this incorrectly.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the previuous test case used a non-RSN AP and that was left in
cfg80211 scan results, it was possible for ap_hs20_random_mac_addr to
pick that old AP from the previous test and reject to connect through
Hotspot 2.0 mechanisms. Work around this test issue by requesting new
set of scan result at the beginning of the test.
Signed-off-by: Jouni Malinen <j@w1.fi>
Some of the test cases where using INTERWORKING_SELECT internally
without using scan_for_bss like the helper functions did. Add explicit
scan_for_bss calls to make the test cases less likely to fail due to
missing BSSes in scan results. This could cause false failure reports
when runnign under heavy load with parallel-vm.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test for an issue where scanning sequence could be
terminated if interworking_find_network_match() finds a matching
network, but wpa_s->auto_select is not set. This could stop connection
attempts when auto_interworking=1 is used and the scan results have a
partially matching network and no cred match.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for a scan to fail to see Probe Response or Beacon frame
under heavy load (e.g., during a parallel-vm.sh test run) since the
dwell time on a chanenl is quite short. Make the test cases using
INTERWORKING_SELECT more robust by trying again if the first attempt
does not find a matching BSS.
Signed-off-by: Jouni Malinen <j@w1.fi>
Verify that session information is stored from Access-Accept and sent to
the station at the requested timeout. Verify that station processes this
notification.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
A bit different code path is used to match the first three different
locations of roaming consortium OI within Beacon frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
This verifies that 'INTERWORKING_SELECT auto' is able to pick the
correct network based on priority configuration when connected to a
lower priority network.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
