Commit graph

173 commits

Author SHA1 Message Date
Jouni Malinen
205d2d1ff5 Fix typos in wpa_supplicant configuration parameter documentation
Signed-off-by: Jouni Malinen <j@w1.fi>
2016-09-10 21:09:52 +03:00
Lior David
d1723c5566 wpa_supplicant: Allow FTM functionality to be published
Add configuration options that control publishing of fine timing
measurement (FTM) responder and initiator functionality via bits 70, 71
of Extended Capabilities element. Typically, FTM functionality is
controlled by a location framework outside wpa_supplicant. When
framework is activated, it will use wpa_supplicant to configure the
STA/AP to publish the FTM functionality. See IEEE P802.11-REVmc/D7.0,
9.4.2.27.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-09-05 21:27:23 +03:00
Jouni Malinen
6c33ca9f95 Add group_rekey parameter for IBSS
The new network profile parameter group_rekey can now be used to specify
the group rekeying internal in seconds for IBSS.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-08-13 16:29:01 +03:00
David Woodhouse
f7cb6e9f24 Update PKCS#11 references in template wpa_supplicant.conf
Ditch the legacy syntax and manual engine mangling and just give an
example using simple PKCS#11 URIs that'll work with both GnuTLS and
OpenSSL.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2016-06-11 12:21:47 +03:00
Jouni Malinen
c86bef2913 wpa_supplicant: Make GAS Address3 field selection behavior configurable
IEEE Std 802.11-2012, 10.19 (Public Action frame addressing) specifies
that the wildcard BSSID value is used in Public Action frames that are
transmitted to a STA that is not a member of the same BSS.
wpa_supplicant used to use the actual BSSID value for all such frames
regardless of whether the destination STA is a member of the BSS.

P2P does not follow this rule, so P2P Public Action frame construction
must not be changed. However, the cases using GAS/ANQP for non-P2P
purposes should follow the standard requirements.

Unfortunately, there are deployed AP implementations that do not reply
to a GAS request sent using the wildcard BSSID value. The previously
used behavior (Address3 = AP BSSID even when not associated) continues
to be the default, but the IEEE 802.11 standard compliant addressing
behavior can now be configured with gas_address3=1.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-06-10 21:44:49 +03:00
Lior David
b6317b417f wpa_supplicant: Add wps_disabled parameter to network block
Add a new parameter wps_disabled to network block (wpa_ssid). This
parameter allows WPS functionality to be disabled in AP mode.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-05-14 19:43:30 +03:00
Jouni Malinen
22950049e4 Ignore pmf=1/2 parameter for non-RSN networks
PMF is available only with RSN and pmf=2 could have prevented open
network connections. Change the global wpa_supplicant pmf parameter to
be interpreted as applying only to RSN cases to allow it to be used with
open networks.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-05 21:09:08 +03:00
Lior David
90f14962ec wpa_supplicant: "don't care" value for pbss in ssid structure
Add a new value 2 to the pbss parameter of wpa_ssid structure, which
means "don't care". This value is used in infrastructure mode to request
connection to either AP or PCP, whichever is available in the scan
results. The value is also used in regular WPS (not P2P group formation)
to make WPS work with devices running as either AP or PCP.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-04-08 12:56:34 +03:00
David Spinadel
c5d193d7b3 MBO: Add cellular capability to MBO IE
Add cellular capability attribute to MBO IE and add MBO IE with cellular
capabilities to Probe Request frames. By default, cellular capability
value is set to Not Cellular capable (3).

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-22 19:53:04 +02:00
David Spinadel
facf2c728a MBO: Add non-preferred channel configuration in wpa_supplicant
Add non-preferred channel configuration to wpa_config for MBO.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2016-02-21 17:55:16 +02:00
Lior David
b907491281 wpa_supplicant: Basic support for PBSS/PCP
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for IEEE 802.11ad devices.

Add a new "pbss" argument to network block. The argument is used
in the following scenarios:
1. When network has mode=2 (AP), when pbss flag is set will start
as a PCP instead of an AP.
2. When network has mode=0 (station), when pbss flag is set will
connect to PCP instead of AP.

The function wpa_scan_res_match() was modified to match BSS according to
the pbss flag in the network block (wpa_ssid structure). When pbss flag
is set it will match only PCPs, and when it is clear it will match only
APs.

Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
2016-02-08 22:23:56 +02:00
Jouni Malinen
aeb408fff1 HS 2.0: Add some documentation for OSEN and network block use
This adds notes on how wpa_supplicant can be configured for OSEN for a
link-layer protected online signup connection and how network profiles
can be set for a Hotspot 2.0 data connection when using external
Interworking network selection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-01-04 21:34:39 +02:00
Jouni Malinen
d6b536f7e5 Add ocsp=3 configuration parameter for multi-OCSP
ocsp=3 extends ocsp=2 by require all not-trusted certificates in the
server certificate chain to receive a good OCSP status. This requires
support for ocsp_multi (RFC 6961). This commit is only adding the
configuration value, but all the currently included TLS library wrappers
are rejecting this as unsupported for now.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-24 00:54:30 +02:00
Jouni Malinen
0ab0de88e8 Document previously missing key_mgmt values
Number of key_mgmt options were missing from the documentation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-12-21 17:45:57 +02:00
Jouni Malinen
3c108b7573 EAP peer: External server certificate chain validation
This adds support for optional functionality to validate server
certificate chain in TLS-based EAP methods in an external program.
wpa_supplicant control interface is used to indicate when such
validation is needed and what the result of the external validation is.

This external validation can extend or replace the internal validation.
When ca_cert or ca_path parameter is set, the internal validation is
used. If these parameters are omitted, only the external validation is
used. It needs to be understood that leaving those parameters out will
disable most of the validation steps done with the TLS library and that
configuration is not really recommend.

By default, the external validation is not used. It can be enabled by
addingtls_ext_cert_check=1 into the network profile phase1 parameter.
When enabled, external validation is required through the CTRL-REQ/RSP
mechanism similarly to other EAP authentication parameters through the
control interface.

The request to perform external validation is indicated by the following
event:
CTRL-REQ-EXT_CERT_CHECK-<id>:External server certificate validation needed for SSID <ssid>

Before that event, the server certificate chain is provided with the
CTRL-EVENT-EAP-PEER-CERT events that include the cert=<hexdump>
parameter. depth=# indicates which certificate is in question (0 for the
server certificate, 1 for its issues, and so on).

The result of the external validation is provided with the following
command:
CTRL-RSP-EXT_CERT_CHECK-<id>:<good|bad>

It should be noted that this is currently enabled only for OpenSSL (and
BoringSSL/LibreSSL). Due to the constraints in the library API, the
validation result from external processing cannot be reported cleanly
with TLS alert. In other words, if the external validation reject the
server certificate chain, the pending TLS handshake is terminated
without sending more messages to the server.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-12-12 18:24:27 +02:00
Avraham Stern
32c02261dd Add support for configuring scheduled scan plans
Add the option to configure scheduled scan plans in the config file.
Each scan plan specifies the interval between scans and the number
of scan iterations. The last plan will run infinitely and thus
specifies only the interval between scan iterations.

usage:
sched_scan_plans=<interval:iterations> <interval2:iterations2> ... <interval>

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-11-30 14:03:28 +02:00
Ben Greear
5b75ecead3 Document passive_scan option for wpa_supplicant.conf
This should save the next person to need this behavior some time.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2015-11-15 19:25:05 +02:00
Jouni Malinen
8406cd3515 Make it clearer that ap_scan=2 mode should not be used with nl80211
Add more details into configuration comments and a runtime info message
if ap_scan=2 is used with the nl80211 driver interface.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-09-05 01:04:29 +03:00
Anton Nayshtut
76ca15b7db FST: wpa_supplicant configuration parameters
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-16 18:26:15 +03:00
Jouni Malinen
5650d379a3 OpenSSL: Add option to disable use of TLSv1.0
The new phase1 config parameter value tls_disable_tlsv1_0=1 can now be
used to disable use of TLSv1.0 for a network configuration. This can be
used to force a newer TLS version to be used. For example,
phase1="tls_disable_tlsv1_0=1 tls_disable_tlsv1_1=1" would indicate that
only TLS v1.2 is accepted.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-07-08 19:27:57 +03:00
Sunil Dutt
94687a0aae WPS: Allow the priority for the WPS networks to be configured
This commit adds a configurable parameter (wps_priority) to specify the
priority for the networks derived through WPS connection.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-06-04 13:55:16 +03:00
Ben Greear
579674ebe5 Document p2p_disabled option in wpa_supplicant.conf
I needed this option to disable P2P on a buggy system.
Document this so someone else finds it quicker next time.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2015-04-24 01:22:15 +03:00
Jouni Malinen
56dfc4939d Fix a typo in configuration parameter documentation
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-04-01 12:57:11 +03:00
Jouni Malinen
a52410c29f Allow PSK/passphrase to be set only when needed
The new network profile parameter mem_only_psk=1 can be used to specify
that the PSK/passphrase for that network is requested over the control
interface (ctrl_iface or D-Bus) similarly to the EAP network parameter
requests. The PSK/passphrase can then be configured temporarily in a way
that prevents it from getting stored to the configuration file.

For example:

Event:
CTRL-REQ-PSK_PASSPHRASE-0:PSK or passphrase needed for SSID test-wpa2-psk

Response:
CTRL-RSP-PSK_PASSPHRASE-0:"qwertyuiop"

Note: The response value uses the same encoding as the psk network
profile parameter, i.e., passphrase is within double quotation marks.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-03-28 11:05:13 +02:00
Jouni Malinen
7f7bfba919 Add an option allow canned EAP-Success for wired IEEE 802.1X
For wired IEEE 802.1X authentication, phase1="allow_canned_success=1"
can now be used to configure a mode that allows EAP-Success (and
EAP-Failure) without going through authentication step. Some switches
use such sequence when forcing the port to be authorized/unauthorized or
as a fallback option if the authentication server is unreachable. By
default, wpa_supplicant discards such frames to protect against
potential attacks by rogue devices, but this option can be used to
disable that protection for cases where the server/authenticator does
not need to be authenticated.

When enabled, this mode allows EAP-Success/EAP-Failure as an immediate
response to EAPOL-Start (or even without EAPOL-Start) and EAP-Success is
also allowed immediately after EAP-Identity exchange (fallback case for
authenticator not being able to connect to authentication server).

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-01 19:22:54 +02:00
Jouni Malinen
49fcc32e91 EAP-MSCHAPv2 peer: Add option to disable password retry query
wpa_supplicant used to request user to re-enter username/password if the
server indicated that EAP-MSCHAPv2 (e.g., in PEAP Phase 2)
authentication failed (E=691), but retry is allowed (R=1). This is a
reasonable default behavior, but there may be cases where it is more
convenient to close the authentication session immediately rather than
wait for user to do something.

Add a new "mschapv2_retry=0" option to the phase2 field to allow the
retry behavior to be disabled. This will make wpa_supplicant abort
authentication attempt on E=691 regardless of whether the server allows
retry.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-02-01 17:45:19 +02:00
Masashi Honma
5a2a6de6a5 mesh: Make inactivity timer configurable
Current mesh code uses ap_max_inactivity as inactivity timer. This patch
makes it configurable.

There is another mesh inactivity timer in mac80211. The timer works even
if user_mpm=1. So this patch sets the max value to the timer for
workaround.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2015-01-19 02:35:43 +02:00
Jouni Malinen
cebee30f31 Add domain_match network profile parameter
This is similar with domain_suffix_match, but required a full match of
the domain name rather than allowing suffix match (subdomains) or
wildcard certificates.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-14 15:45:18 +02:00
Jouni Malinen
483dd6a5e0 Include peer certificate always in EAP events
This makes it easier for upper layer applications to get information
regarding the server certificate without having to use a special
certificate probing connection. This provides both the SHA256 hash of
the certificate (to be used with ca_cert="hash://server/sha256/<hash>",
if desired) and the full DER encoded X.509 certificate so that upper
layer applications can parse and display the certificate easily or
extract fields from it for purposes like configuring an altsubject_match
or domain_suffix_match.

The old behavior can be configured by adding cert_in_cb=0 to
wpa_supplicant configuration file.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-14 12:24:52 +02:00
Jouni Malinen
394b54732e Improve subject_match and domain_suffix_match documentation
These were already covered in both README-HS20 for credentials and in
header files for developers' documentation, but the copy in
wpa_supplicant.conf did not include all the details. In addition, add a
clearer note pointing at subject_match not being suitable for suffix
matching domain names; domain_suffix_match must be used for that.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-11 00:27:01 +02:00
Stefan Tomanek
79cd993a62 Add address masks to BSSID lists
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).

This change expands the data structures used by MAC lists to include a
mask indicating the significant (non-masked) portions of an address and
extends the list parser to recognize mask suffixes.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-01-10 17:35:53 +02:00
Stefan Tomanek
b83e455451 Add network specific BSSID black and white lists
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.

This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.

Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
2015-01-10 17:35:53 +02:00
Masashi Honma
4b4093686b mesh: Make maximum number of peer links configurable
Maximum number of peer links is maximum number of connecting mesh peers
at the same time. This value is 0..255 based on the
dot11MeshNumberOfPeerings range.

Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
2014-12-21 23:52:31 +02:00
Jouni Malinen
02a8d45ace ERP: Add support for ERP on EAP peer
Derive rRK and rIK on EAP peer if ERP is enabled. The new wpa_supplicant
network configuration parameter erp=1 can now be used to configure the
EAP peer to derive EMSK, rRK, and rIK at the successful completion of an
EAP authentication method. This functionality is not included in the
default build and can be enabled with CONFIG_ERP=y.

If EAP authenticator indicates support for re-authentication protocol,
initiate this with EAP-Initiate/Re-auth and complete protocol when
receiving EAP-Finish/Re-auth.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-04 12:16:29 +02:00
Thomas Pedersen
9e5e03d77e Add examples of new mesh options into wpa_supplicant.conf
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-11-20 16:31:09 +02:00
Thomas Pedersen
e45e898970 mesh: Add user_mpm config option
Add user_mpm config parameter, when this is set to 1 (the default) the
peer link management is done on userspace, otherwise the peer management
will be done by the kernel.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Thomas Pedersen <thomas@noack.us>
2014-10-25 17:43:24 +03:00
Jouni Malinen
07e2de3193 wpa_supplicant: Allow OpenSSL cipherlist string to be configured
The new openssl_cipher configuration parameter can be used to select
which TLS cipher suites are enabled for TLS-based EAP methods when
OpenSSL is used as the TLS library. This parameter can be used both as a
global parameter to set the default for all network blocks and as a
network block parameter to override the default for each network
profile.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-10-12 11:55:13 +03:00
Jouni Malinen
a313d17de9 Extend random MAC address support to allow OUI to be kept
mac_addr=2 and preassoc_mac_addr=2 parameters can now be used to
configure random MAC address to be generated by maintaining the OUI part
of the permanent MAC address (but with locally administered bit set to
1). Other than that, these values result in similar behavior with
mac_addr=1 and preassoc_mac_addr=1, respectively.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-30 00:40:23 +03:00
Jouni Malinen
c267753ba2 Add support for using random local MAC address
This adds experimental support for wpa_supplicant to assign random local
MAC addresses for both pre-association cases (scan, GAS/ANQP) and for
connections. MAC address policy for each part can be controlled
separately and the connection part can be set per network block.

This requires support from the driver to allow local MAC address to be
changed if random address policy is enabled. It should also be noted
that number of drivers would not support concurrent operations (e.g.,
P2P and station association) with random addresses in use for one or
both.

This functionality can be controlled with the global configuration
parameters mac_addr and preassoc_mac_addr which set the default MAC
address policies for connections and pre-association operations (scan
and GAS/ANQP while not connected). The global rand_addr_lifetime
parameter can be used to set the lifetime of a random MAC address in
seconds (default: 60 seconds). This is used to avoid unnecessarily
frequent MAC address changes since those are likely to result in driver
clearing most of its state. It should be noted that the random MAC
address does not expire during an ESS connection, i.e., this lifetime is
only for the case where the device is disconnected.

The mac_addr parameter can also be set in the network blocks to define
different behavior per network. For example, the global mac_addr=1 and
preassoc_mac_addr=1 settings and mac_addr=0 in a home network profile
would result in behavior where all scanning is performed using a random
MAC address while connections to new networks (e.g.,
Interworking/Hotspot 2.0) would use random address and connections to
the home network would use the permanent MAC address.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-09-27 20:07:19 +03:00
Jouni Malinen
1b928f96b6 P2P: Allow passphrase length to be configured
Previously, eight character random passphrase was generated
automatically for P2P GO. The new p2p_passphrase_len parameter can be
used to increase this length to generate a stronger passphrase for cases
where practicality of manual configuration of legacy devices is not a
concern.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-06-22 00:15:53 +03:00
Nirav Shah
d3b204694a P2P: Make the default p2p_find delay value configurable
This makes the p2p_find default delay value configurable as
p2p_search_delay parameter through the configuration file (and through
control interface "SET p2p_search_delay <value>" on the P2P management
interface.

This parameter controls the number milliseconds of extra delay that is
added between search iterations when there is a concurrent operation in
progress. This can be used, e.g., p2p_search_delay=100 to make p2p_find
friendlier to concurrent operations by avoiding it from taking 100% of
the radio resources. The default value is the previous default, i.e.,
500 ms. Smaller values can be used to find peers more quickly at the
cost of larger effect to concurrent operations while a larger value
leaves more time for the concurrent operations at the cost of making
device discovery take longer time.

The optional p2p_find delay argument can still be used to override the
search delay for each search operation.

Since the P2P_CONCURRENT_SEARCH_DELAY macro is not used anymore, the
driver specific build parameter for bcmdhd from Android.mk is also
removed. Similar configuration can now be achieved with
p2p_search_delay=0 in the p2p0 interface configuration file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-06-09 19:43:26 +03:00
Hu Wang
dd10abccc8 MACsec: wpa_supplicant integration
Add MACsec to the wpa_supplicant build system and configuration file.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-05-09 20:42:44 +03:00
Naresh Jayaram
13f6a07efc Add SIM identifier to the network profile and cred block
This allows the specific SIM to be identified for authentication
purposes in multi-SIM devices. This SIM number represents the index of
the SIM slot. This SIM number shall be used for the authentication using
the respective SIM for the Wi-Fi connection to the corresponding
network.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-24 12:15:32 +03:00
Jouni Malinen
d41cc8ccf6 Allow HT 40 MHz intolerant flag to be set for association
This extends HT overrides to allow HT 40 MHz intolerant flag to be set
with ht40_intolerant=1.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-04-17 17:11:17 +03:00
Jouni Malinen
e74dd0e55b Add forgotten ampdu_factor into wpa_supplicant.conf
Signed-off-by: Jouni Malinen <j@w1.fi>
2014-04-13 10:26:53 +03:00
Pawel Kulakowski
39a5800f7c wpa_supplicant: Allow disabling LDPC
Allows user to disable LDPC coding.
This possibility is useful for testing purpose.

Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
2014-04-01 11:20:48 +03:00
David Spinadel
268043d55f bgscan: Do not initialize bgscan if disabled by user
Do not initialize bgscan if the user explicitly set bgscan to an empty
string. Without this patch wpa_supplicant tries to initialize bgscan to
the first option if the string is empty.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
2014-03-04 22:26:19 +02:00
Jouni Malinen
cf6d08a63f Interworking: Add OCSP parameter to the cred block
This new parameter can be used to configure credentials to mandate use
of OCSP stapling for AAA server authentication.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:24 +02:00
Jouni Malinen
33fb8c526c HS 2.0R2: Add support for Policy/RequiredProtoPortTuple
The new credential parameter req_conn_capab can be used to specify
restrictions on roaming networks providing connectivity for a set of
protocols/ports.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
a45b2dc5dc HS 2.0R2: Add support for Policy/MaximumBSSLoadValue
The new credential parameter max_bss_load can be used to specify
restrictions on BSS Load in the home network.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
4cad9df15a HS 2.0R2: Add support for Policy/MinBackhaulThreshold
The new credential parameters min_{dl,ul}_bandwidth_{home,roaming} can
be used to specify restrictions on available backhaul bandwidth.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
aa26ba68b4 HS 2.0R2: Add tracking of provisioning SP
The new provisioning_sp cred field can now be used to track which SP
provisioned the credential. This makes it easier to find the matching
PPS MO from the management tree (./Wi-Fi/<provisioning_sp>).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:23 +02:00
Jouni Malinen
f9cd147d6b HS 2.0R2: Update Indication element to Release 2
The HS 2.0 Indication element from wpa_supplicant now includes the
release number field and wpa_supplicant shows the release number of the
AP in STATUS command (hs20=1 replaced with hs20=<release>).

The new update_identifier field in the cred block can now be used to
configure the PPS MO ID so that wpa_supplicant adds it to the Indication
element in Association Request frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:22 +02:00
Jouni Malinen
bc00053c9d Interworking: Allow roaming partner configuration
The new roaming_partner parameter within a cred block can be used to
configure priorities for roaming partners.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2014-02-26 01:24:22 +02:00
Dmitry Shmidt
e9a6f18385 TLS: Add tls_disable_tlsv1_1 and tls_disable_tlsv1_2 phase1 params
These can be used to disable TLSv1.1 and TLSv1.2 as a workaround for AAA
servers that have issues interoperating with newer TLS versions.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
2014-02-20 15:28:57 +02:00
Jouni Malinen
03ed332407 Interworking: Allow cred blocks not to be saved to a file
The new cred block parameter 'temporary' can be used to indicate that a
cred block is not to be saved to wpa_supplicant configuration file
(e.g., "SET_CRED 0 temporary 1"). This is similar to the concept of
temporary network blocks and allows cred blocks to be managed outside
the wpa_supplicant config file when other parameters are still saved to
the file written by wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-30 15:43:55 +02:00
Jouni Malinen
b2838baf6a Update IBSS documentation to include RSN option
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-23 20:21:17 +02:00
Haim Dreyfuss
3139270903 bgscan: Add global bgscan configuration
This option can be used to globally configure bgscan parameters
for all the network blocks.

Note that this configuration will not override a network block
specific bgscan settings, but will only be used in case that
the network block does not have a valid bgscan configuration.

Signed-hostap: Haim Dreyfuss <haim.dreyfuss@intel.com>
2013-11-05 10:26:31 +02:00
Jouni Malinen
65015b2d8e Replace unnecessary UTF-8 characters with ASCII versions
There is no need for using UTF-8 in these files when perfectly fine
ASCII versions of these characters exist.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-02 16:01:32 +02:00
Jouni Malinen
463c8ffbd5 Interworking: Add support for multiple home FQDNs
Credentials can now be configured with more than one FQDN ('domain'
field in the cred block) to perform Domain Name List matching against
multiple home domains.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-18 14:13:45 +03:00
Jouni Malinen
080585c01a Add support for OCSP stapling to validate server certificate
When using OpenSSL with TLS-based EAP methods, wpa_supplicant can now be
configured to use OCSP stapling (TLS certificate status request) with
ocsp=1 network block parameter. ocsp=2 can be used to require valid OCSP
response before connection is allowed to continue.

hostapd as EAP server can be configured to return cached OCSP response
using the new ocsp_stapling_response parameter and an external mechanism
for updating the response data (e.g., "openssl ocsp ..." command).

This allows wpa_supplicant to verify that the server certificate has not
been revoked as part of the EAP-TLS/PEAP/TTLS/FAST handshake before
actual data connection has been established (i.e., when a CRL could not
be fetched even if a distribution point were specified).

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-06-30 01:01:15 +03:00
Ben Greear
6124e858fd wpa_supplicant: Allow vifs to scan only current channel
If a VIF is already associated, then only scan on the associated
frequency if user requests such. This is a big help when using
lots of virtual stations.

Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
2013-05-09 12:43:40 +03:00
Ben Greear
f5ffc348dc wpa_supplicant: Allow global scan frequencies configuration
This allows one to limit the channels that wpa_supplicant will
scan. This is a useful addition to the freq_list configurable
in the network {} section.

Signed-hostap: Ben Greear <greearb@candelatech.com>
2013-05-05 11:46:54 +03:00
Jouni Malinen
4342326fc7 Add ignore_old_scan_res configuration parameter
This can be used to configure wpa_supplicant to ignore old scan results
from the driver cache in cases where such results were not updated after
the scan trigger from wpa_supplicant. This can be useful in some cases
where the driver may cache information for a significant time and the AP
configuration is changing. Many such cases are for testing scripts, but
this could potentially be useful for some WPS use cases, too.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-31 18:05:42 +03:00
Jouni Malinen
18a2eaabe3 Add ap_vendor_elements for wpa_supplicant AP/P2P GO mode
This new parameter allows wpa_supplicant AP mode operations to use
similar design to the vendor_elements parameter in hostapd to add
vendor_elements into Beacon/Probe Response IE parameters.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-21 15:52:41 +02:00
Johannes Berg
e9ee8dc394 wpa_supplicant: Support VHT capability overrides
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-03-10 18:04:39 +02:00
Jouni Malinen
18206e02c5 Allow wpa_supplicant AP mode to configure Beacon interval
beacon_int (in TU) can now be used to configure Beacon interval for AP
mode operations (including P2P GO) in wpa_supplicant. This can be set
either in a network block or as a global parameter in the configuration
file (or with "SET beacon_int <value>" control interface command) to
apply for all networks that do not include the beacon_int parameter to
override the default.

In addition, this commits extends the dtim_period parameter to be
available as a global parameter to set the default value. dtim_period is
now stored in the configuration file, too, if it was set.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-01 20:50:08 +02:00
Jouni Malinen
625f202a74 SAE: Allow enabled groups to be configured
hostapd.conf sae_groups parameter can now be used to limit the set of
groups that the AP allows for SAE. Similarly, sae_groups parameter is
wpa_supplicant.conf can be used to set the preferred order of groups. By
default, all implemented groups are enabled.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:53 +02:00
Jouni Malinen
2474ce4542 Document bgscan configuration options
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-25 20:43:07 +02:00
Ben Greear
c8d22af88f wpa_supplicant: Document HT capability overrides
Signed-off-by: Ben Greear <greearb@candelatech.com>
2012-12-18 14:49:35 +02:00
Jouni Malinen
dbea8ac7ab Interworking: Allow SSID-based network exclusion for credentials
The new excluded_ssid parameter within a cred block can be used to
excluded networks from matching with credentials.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:01:50 +02:00
Jouni Malinen
62d4980331 Allow PMF to be enabled by default
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-24 22:21:29 +02:00
Jouni Malinen
6e2020210a Allow OKC to be enabled by default
Previously, OKC (opportunistic key caching, a.k.a. proactive key
caching) could be enabled only with a per-network parameter
(proactive_key_caching). The new global parameter (okc) can now be used
to change the default behavior to be OKC enabled (okc=1) for network
blocks that do not override this with the proactive_key_caching
parameter.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-12 20:07:53 +02:00
Jouni Malinen
e026159a8e EAP-SIM/AKA: Store pseudonym identity in configuration
Use the anonymous_identity field to store EAP-SIM/AKA pseudonym identity
so that this can be maintained between EAP sessions (e.g., after
wpa_supplicant restart) even if fast re-authentication data was cleared.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-02 13:04:18 +03:00
Jouni Malinen
4d5bda5fca Interworking: Add optional use of network selection on normal scans
auto_interworking=1 configuration parameter can be used to request
wpa_supplicant to use Interworking network selection automatically as a
part of the normal (non-Interworking) network selection if the scan
results do not match with enabled networks. This makes scanning work
similarly to the "interworking_select auto" command.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-08-28 16:14:13 +03:00
Jouni Malinen
9af7361b3f Document TLS options in phase1/phase2
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-17 22:27:29 +03:00
Eyal Shapira
462a7439e1 Add p2p_go_max_inactivity config option
This enables setting a different max inactivity timeout for P2P GO.
This timeout is used to detect inactive clients. In some scenarios
it may be useful to have control over this and set a shorter timeout
than the default 300s. For example when running STA and P2P GO interfaces
concurrently, the STA interface may perform scans which may cause the
GO to miss a disassoc / deauth frames from a client and keep assuming
that the client is connected until the inactivity detection kicks in.
300 secs is a bit too long for such scenarios and creates a bad user
experience.

Signed-hostap: Eyal Shapira <eyal@wizery.com>
2012-08-10 16:28:38 +03:00
Jouni Malinen
5c4b93d72e Add support for using printf-escaped strings in configuration
P"<escaped string>" can now be used as an alternative method for
specifying non-ASCII strings (including control characters). For
example, ssid=P"abc\x00test".

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-07 13:50:39 +03:00
Jouni Malinen
0ebb23e340 EXT PW: Add support for password parameter from external storage
This allows the password parameter for EAP methods to be fetched
from an external storage.

Following example can be used for developer testing:

ext_password_backend=test:pw1=password|pw2=testing

network={
    key_mgmt=WPA-EAP
    eap=TTLS
    identity="user"
    password=ext:pw1
    ca_cert="ca.pem"
    phase2="auth=PAP"
}

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-03 22:15:42 +03:00
Jouni Malinen
9173b16fd1 EXT PW: Add support for psk parameter from external storage
This allows wpa_supplicant configuration file to be created without
the PSK/passphrase value included in the file when a backend for
external password storage is available.

Following example can be used for developer testing:

ext_password_backend=test:psk1=12345678
network={
    ssid="test-psk"
    key_mgmt=WPA-PSK
    psk=ext:psk1
}

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-03 22:15:42 +03:00
Jouni Malinen
306ae22556 EXT PW: Add framework for supporting external password storage
This new mechanism can be used to make wpa_supplicant using external
storage (e.g., key store in the operating system) for passwords,
passphrases, and PSKs. This commit is only adding the framework part
needed to support this, i.e., no actual configuration parameter can
yet use this new mechanism. In addition, only a simple test backend
is added to allow developer testing of the functionality.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-03 22:15:42 +03:00
Jouni Malinen
955567bc09 Interworking: Add support for using Roaming Consortium OI for matching
Each cred block can now be matched based on Roaming Consortium OI as an
alternative mechanism to using NAI Realm information. This may be
optimized for efficiency in the future since Roaming Consortium
information is available in scan results without having to go through
ANQP queries. In addition, this is easier to support in case there is a
large number of realms that can be used for authentication.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-02 18:48:31 +03:00
Jouni Malinen
8ca93c59e0 Interworking: Allow pre-configuration of EAP parameters
The new cred block parameters eap, phase1, and phase2 can be used to
select which EAP method is used with network selection instead of using
the value specified in ANQP information (e.g., NAI Realm).

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-08-02 18:40:45 +03:00
Jouni Malinen
51ca03f470 WPS: Document NFC use cases with password/config token
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-06-28 21:28:49 +03:00
Tomasz Bursztyka
e3659c89d2 Add a simple periodic autoscan module
This module will sets a fixed scanning interval. Thus, the parameter to
this module is following this format: <fixed interval>

Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2012-06-26 19:28:21 +03:00
Tomasz Bursztyka
c0fba2b38d Add autoscan module named exponential
This module will compute the interval on a base exponential. Thus,
params to this module are following this format: <base>:<limit>

Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2012-06-26 19:22:56 +03:00
Tomasz Bursztyka
b0786fba71 Add autoscan parameters support in config file
Signed-hostap: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2012-06-26 18:09:57 +03:00
Etay Luz
fdfb1c8bcf wpa_supplicant: Support dtim_period configuration for AP mode
Signed-off-by: Etay Luz <eluz@qca.qualcomm.com>
2012-06-04 17:52:37 +03:00
Jay Katabathuni
66aadbd7bf HS 2.0: Add runtime configuration of Hotspot 2.0 station
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-05-08 23:29:45 +03:00
Jouni Malinen
4732ee3a87 Add more documentation for IEEE 802.11w/PMF configuration
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-05-05 16:48:23 +03:00
Anirban Sirkhell
71dd3b78f9 WPS: Allow vendor specific attribute to be added into M1
wps_vendor_ext_m1 configuration parameter can now be used to add a
vendor specific attribute into the WPS M1 message, e.g., for
Windows Vertical Pairing.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-04-04 00:08:57 +03:00
Vasanthakumar Thiagarajan
07f53b8cc7 wpa_supplicant: Add provision to configure inactivity period in AP mode
This patch adds a configuration in network block, ap_max_inactivity, for
station's inactivity period when in AP mode. The time period is
configured in seconds, by default 300 seconds.

Signed-hostap: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
2012-03-27 20:49:44 +03:00
Jouni Malinen
d7b01abd5e Interworking: Support real SIM/USIM card for network selection
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-03-04 16:02:56 +02:00
Jouni Malinen
817bb3e1c1 Interworking: Fix credential block example
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-03-04 11:24:24 +02:00
Jouni Malinen
400020cbe8 Interworking: Update configuration file documentation for credentials
Signed-hostap: Jouni Malinen <j@w1.fi>
2012-03-03 10:49:02 +02:00
Jouni Malinen
2a4b98a912 Interworking: Document network selection parameters 2011-10-16 23:55:34 +03:00
Jouni Malinen
46ee0427b1 IEEE 802.11u: Allow Interworking and HESSID to be configured
The new wpa_supplicant.conf file global parameters interworking and
hessid can be used to configure wpa_supplicant to include
Interworking element in Probe Request frames.
2011-10-16 23:55:34 +03:00
Pavel Roskin
ffbf1eaa26 Fix typos found by codespell
Signed-off-by: Pavel Roskin <proski@gnu.org>
2011-09-22 00:43:59 +03:00
Jouni Malinen
53587ec183 WPS 2.0: Make WSC 2.0 support to be build option (CONFIG_WPS2)
For now, the default build will only include WSC 1.0 support.
CONFIG_WPS2=y can be used to add support for WSC 2.0.
2010-09-09 06:07:48 -07:00
Jouni Malinen
6a857074f4 WPS 2.0: Add virtual/physical display and pushbutton config methods 2010-09-09 06:07:47 -07:00