This offloads the station polling to driver wrappers, which may offload
it again to the driver. The hostap driver wrapper uses "real" data
frames while nl80211 uses null data frames.
Also add a specific event to indicate that a poll was successful for
future use with the nl80211 driver.
Some dualband cards can use more than five seconds to run through
a full scan, so increase the timeout to avoid hitting the missing
scan completed event workaround.
Remove the separate driver_ops functions set_cts_protect(),
set_preamble(), set_short_slot_time(), and set_ht_params(). These
belong into same set of operations as set_ap(), so there is no need
to maintain separate functions that just make the driver wrapper
more complex.
Since these have only been used with driver_nl80211.c, the driver_ops
can be removed immediately instead of maintaining backwards
compatibility period with the old functions.
The AP client isolation parameter is now available through set_ap().
driver_nl80211.c was the only driver wrapper using the set_intra_bss()
call in hostap.git, but some external trees may have used this. Once
those are cleared, the set_infra_bss() driver_ops can be removed
completely. The only remaining use case for it currently is in P2P
GO mode with wpa_supplicant.
"hostapd_cli ess_disassoc (STA addr) (URL)" can now be used to send
an ESS Dissassociation Imminent notification to the STA. This event
is shown in wpa_supplicant ctrl_iface monitors (e.g., wpa_cli):
"WNM: ESS Disassociation Imminent - session_info_url=http://example.com/session/"
Use the SSID filter list passed in the scheduled scan request down to
the kernel driver, so it can use the list to return only the wanted
SSIDs. Some kernel drivers can use this information to offload the
SSID filter to the hardware, helping with reducing the power
consumption.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pass SSIDs to be matched in scheduled scan results. Only the SSIDs
that are included in the match lists will be reported by the driver,
so the filtering can be offloaded to the hardware and the power
consumption can be reduced.
Signed-off-by: Luciano Coelho <coelho@ti.com>
With scheduled scan support, we may need to pass more than 10 SSIDs in
a single scan request. Some drivers (e.g., wl12xx) support up to 16
SSIDs at once.
Change WPAS_MAX_SCAN_SSIDS from 10 to 16.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In new Linux kernel versions (>=3.0), nl80211 adds scheduled scan
capability. In order to use this feature to its full extent, we need
to support it in the wpa_supplicant core, so that it can also be used
by other drivers.
This commit adds initial scheduled scan support operations and events.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently the P2P Interface name[p2p-%s-%d] is reset when the P2P
Interface name reaches the "IFNAMSIZ" limit. Monitor interface name is
derived from p2p interface name with the addition of few characters
[mon.p2p-%s-%d] and hence Monitor interface name hits IFNAMSIZ limit
before P2P Interface name. Rename the monitor interface name to
mon-%s-%d to reduce the length to same with p2p-%s-%d.
The new function, p2p_scan_ie_buf_len(), can be used to figure out
how large a buffer needs to be allocated for p2p_scan_ie() use. This
makes it easier to add new data into the buffer without forcing all
callers to be updated to use a larger buffer.
This new flag can be used to change wpa_supplicant behavior in the
default ap_scan=1 mode to move BSS selection into the driver (likely
firmware). This commit is only adding the flag; separate commits
will be used to change the actual connection/roaming behavior.
The "too long" buffer (32+1 octets) prevented AP from starting up with
32 octet SSID with WE-21 and newer. Fix this by reducing the
SIOCGIWESSID buffer length.
This adds support for RSN pre-authentication with nl80211 interface and
drivers that handle roaming internally (i.e., wpa_supplicant is not
responsible for requesting scan results that provide the needed
information without these events).
cfg80211 does not currently allow NL80211_CMD_CONNECT when there
is already an association. This can result in wpa_supplicant being
unable to request a connection if the interface is already in
connected state. Work around this by requesting disconnection if
the connect command fails with EALREADY error. This allows
wpa_supplicant to recover from the unexpected state and complete
the connect request on next attempt.
Currently, the following can happen:
1) P2P state machine requests R-O-C
2) user changes their mind and aborts
3) P2P state machine aborts R-O-C
4) driver_nl80211 rejects abort since there
was no notification about the start yet
5) R-O-C period start notification from kernel
6) P2P state machine requests new R-O-C
7) this overlaps with old R-O-C -- iwlwifi driver
can't handle that and returns -EBUSY
8) state machine stops dead in its tracks
The reason is that the abort isn't going through properly. Instead of
tracking whether a R-O-C is active in driver_nl80211, track whether one
was requested to avoid this scenario.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to disable CCK rates from Probe Request frames.
For nl80211, this is currently applying only to the supported rates
element(s), but this mechanism could be extended to address TX rate
control masking, too, to lessen need for global rate disabling.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Since the kernel can now advertise P2P concurrent support by advertising
interface combinations, we can take advantage of that and automatically
use P2P_CONCURRENT / P2P_MGMT_AND_NON_P2P for drivers that advertise
support.
Keep driver_param=use_p2p_group_interface=1 for anyone not advertising
interface combinations in their drivers yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous code was trying to figure out which WPA version is
used based on the extra IEs requested for Association Request. That
did not work properly in cases where non-WPA networks are used with
some extra IEs. Fix this by using more robust mechanism for passing
the WPA versions from core wpa_supplicant to the driver_ops
associate().
This allows non-mac80211 drivers to report received Probe Request
frames to user space and Probe Response and Action frames to be sent
from user space when using AP/P2P GO mode.
This allows the driver to use PS buffering of Deauthentication and
Disassociation frames when the STA is in power save sleep. The STA
entry (and PTK) will be removed from the kernel only after the
Deauth/Disassoc has been transmitted (e.g., when the STA wakes up).
A hardcoded two second timeout is used to limit the length of this
window should the driver fail to deliver the frame (e.g., the STA
is out of range and does not wake up). The kernel STA entry is
marked unauthorized during the wait to avoid accepting Data
frames from the STA that we have decided to disconnect.
This behavior is available only with drivers that provide TX status
events for Deauth/Disassoc frames (nl80211 at this point). Other
drivers continue to use the previous behavior where the STA entry
is removed immediately.
This change is a first step in better supporting different driver
architectures for AP mode operations with nl80211. This commit in
itself does not add new functionality, but it makes it easier to add
new AP mode parameters to address needs of drivers that have more of
the MLME/SME in firmware or kernel.