This drops support for the fi.epitest.hostap.WPASupplicant D-Bus name
along with the associated CONFIG_CTRL_IFACE_DBUS option. Nothing should
really be using this since 2010.
This is a just a straightforward removal. Perhaps the dbus_common.c and
dbus_new.c can be merged now. Also, the "_NEW" suffix of the config
option seems to make even less sense than it used to.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Also add the ChangeLog entries for both hostapd and wpa_supplicant to
describe main changes between v2.6 and v2.7.
Signed-off-by: Jouni Malinen <j@w1.fi>
System tray icon can be set to 5 different pictographs according to the
connection status. One for disconnected state (not associated with the
network, or not connected with the wpa_supplicant service), and four for
connected status (showing the signal strength on the receiver).
By default this functionality is disabled. The reason for this, is the
fact, that the underlaying approach of this functionality is poll based,
which might be considered as a non-efficient one. Update interval has to
be set explicitly by the user with '-m<seconds>' command line argument.
Status icon names are based on various Gnome icon packs (e.g., Faba).
When icon can not be found, default one is shown (wpa_gui logo).
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
In the commit 77b244d577a7cb5c928478627af6687a0733193d9 ('wpa_gui: Quiet
mode - disable tray icon messages') a new parameter has been introduced,
but it was not documented. This commit fixes this omission.
Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Unexpected trailing zero causes following error.
wpa_supplicant.sgml:472:53:E: character data is not allowed here
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
The man page source was not up-to-date with removed driver wrappers,
so bring in the wpa_supplicant/README changes to make this somewhat
closer to the current state.
Signed-hostap: Jouni Malinen <j@w1.fi>
There is no real reason to maintain these in the current development
branch anymore. If someone really needs support for the obsolete
driver interfaces, these can be found in older wpa_supplicant
branches.
driver_atmel.c
- vendor-specific interface for ATMEL AT76C5XXx cards
- for some old out-of-tree driver; not for the upstream atmel*
drivers
driver_ndiswrapper.c
- vendor-specific interface for an out-of-tree driver
- ndiswrapper should work with driver_wext.c, too
driver_ipw.c
- vendor-specific interface for old ipw2100/2200 driver
- the upstream driver works with driver_wext.c (and does not work
with the old interface)
driver_hermes.c
- vendor driver that was not even included in the main wpa_supplicant
releases
For example, -Dnl80211,wext could be used to automatically select
between nl80211 and wext. The first driver wrapper that is able to
initialize the interface will be used.
Replace " wpa_supplicant" with " %wpa_supplicant" except for
"struct wpa_supplicant". This makes it easier to write Doxygen comments
since there is no need to add the ugly '%' prefix to each instance of
wpa_supplicant text showing up.
This updated all doxygen runs to use the same style that was used for
wpa_supplicant full documents. The full vs. fast configurations are now
otherwise identical apart from fast not generating dot files or
latex/pdf version of the documentation.
Find attached the patch that creates a new driver: roboswitch. This
driver adds support for wired authentication with a Broadcom
RoboSwitch chipset. For example it is now possible to do wired
authentication with a Linksys WRT54G router running OpenWRT.
LIMITATIONS
- At the moment the driver does not support the BCM5365 series (though
adding it requires just some register tweaks).
- The driver is also limited to Linux (this is a far more technical
restriction).
- In order to compile against a 2.4 series you need to edit
include/linux/mii.h and change all references to "u16" in "__u16". I
have submitted a patch upstream that will fix this in a future version
of the 2.4 kernel. [These modifications (and more) are now included in
the kernel source and can be found in versions 2.4.37-rc2 and up.]
USAGE
- Usage is similar to the wired driver. Choose the interfacename of
the vlan that contains your desired authentication port on the router.
This name must be formatted as <interface>.<vlan>, which is the
default on all systems I know.
Allow application to be started in the system tray only when started with
the `-t' command line argument.
Signed-off-by: Kel Modderman <kel@otaku42.de>
Documentation appeared a little vague about which options are global and
which are tied to a particular interface. This leads to confusion when
using certain combinations of options, e.g. the command "wpa_supplicant
-c /etc/wpa_supplican.conf -u" will not do what is intuitively expected
from it - it will not read the config file given with -c option because
no -i option was given. This command is still valid because -u option is
used. The wpa_supplicant running like this will also not listen on any
control socket, because the socket file name is usually given in the
config file. This command line also happens to be the default in Fedora 9.
This patch does not try to change any behaviour, but rather document
these nuances clearly.
Explain that wpa_supplicant supports a variety of drivers, but only a
subset of them are chosen at compile time.
Signed-off-by: Kel Modderman <kel@otaku42.de>
The Debian package checker "lintian" was making noise about
wpa_supplicant.conf(5). It was caused by a line beginning with ', which is
apparently not liked by man(1).
I suggest the use of <emphasis>word</emphasis> where 'word' is used at the
moment.
Signed-off-by: Kel Modderman <kel@otaku42.de>
