LibreSSL v2.7 claims an OPENSSL_VERSION_NUMBER value that would indicate
that SSL_OP_NO_TLSv1_3 is available, but that does not seem to be the
case with LibreSSL. As such, skip this step based on whether
SSL_OP_NO_TLSv1_3 is defined to avoid build issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
The recently introduced sae_password parameter was only handled properly
in wpa_supplicant/sme.c while wpa_supplicant/mesh.c assumed that
ssid->passphrase exclusively holds the secret.
Import the logic from sme.c to mesh.c to allow having only sae_password
set which otherwise throws this error:
AP-ENABLED
mesh: Passphrase for SAE not configured
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
pmksa_cache stubs have not been updated when function prototypes have
been modified in commit 852b2f2738 (SAE: Only allow SAE AKMP for PMKSA
caching attempts). Add new function parameter int akmp to stubs of
pmksa_cache_get() and pmksa_cache_set_current() as well to fix build.
Fixes: 852b2f2738 ("SAE: Only allow SAE AKMP for PMKSA caching attempts")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Explicitly check the PMKSA cache entry to have matching SAE AKMP for the
case where determining whether to use PMKSA caching instead of new SAE
authentication. Previously, only the network context was checked, but a
single network configuration profile could be used with both WPA2-PSK
and SAE, so should check the AKMP as well.
Signed-off-by: Jouni Malinen <j@w1.fi>
The RSN supplicant state machine PMK was set based on WPA PSK even for
the cases where SAE would be used. If the AP allows PMKSA caching to be
used with SAE, but does not indicate the selected PMKID explicitly in
EAPOL-Key msg 1/4, this could result in trying to use the PSK instead of
SAE PMK. Fix this by not setting the WPA-PSK as default PMK for SAE
network profiles and instead, configuring the PMK explicitly from the
found PMKSA cache entry.
Signed-off-by: Jouni Malinen <j@w1.fi>
This gives more protection against unexpected behavior if RSN supplicant
code ends up trying to use sm->pmk[] with a stale value. Couple of the
code paths did not clear sm->pmk_len explicitly in cases where the old
PMK is being removed, so cover those cases as well to make sure these
will result in PMK-to-PTK derivation failures rather than use of
incorrect PMK value if such a code path could be reached somehow.
Signed-off-by: Jouni Malinen <j@w1.fi>
Couple of these were not preceded by wpa_hexdump_key(PSK) which made it
more difficult to interpret the debug log.
Signed-off-by: Jouni Malinen <j@w1.fi>
Add a new wifi test config attribute to configure HE LTF in the
driver. This is used for testbed configuration.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
If there is no explicit wmm_enabled parameter in the configuration
(i.e., conf->wmm_enabled == -1), the configuration reload path needs to
initialize conf->wmm_enabled based on iconf->ieee80211n in
hostapd_reload_bss() similarly to what is done in the initial startup
case in hostapd_setup_bss().
This fixes issues with RSN capabilities being set incorrectly when WMM
is supposed to get enabled and unexpectedly enabling WMM when it is not
supposed to be enabled (HT disabled). Either of these issues could show
up when asking hostapd to reload the configuration file (and when that
file does not set wmm_enabled explicitly).
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This ensures a session timeout configured on R0KH either using
RADIUS-based ACL or 802.1X authentication is copied over to the new
R1KH.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This is needed to allow the remaining session time to be computed for FT
(when sending PMK-R1 to another AP).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Handle the special case of no PMK-R0 entry in the caller instead of
having to have wpa_ft_rrb_build_r0() aware of the possibility of pmk_r0
being NULL.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
ieee802_11_set_radius_info() might be called with a STA entry that has
already stored identity and/or radius_cui information, so make sure the
old values get freed before being replaced by the new ones.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
time.sleep() in run_roams() is required because the target AP sets the
key once the station was associated. There are races, when the station
processes the (Re)Association Response frame AND the test suite starts
FT_DS before the AP processes its local confirmation and thus
wpa_auth_sm_event(ASSOC_FT). Therefore, the ActionFrame will be lost, as
the AP driver is missing the key.
Since this is this speed is highly synthetic, wait a few milliseconds
before roaming back.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
This uses set_vlan()/get_vlan() callbacks to fetch and configure the
VLAN of STA. Transmission of VLAN information between APs uses new TLVs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
IEEE Std 802.11-2016, 12.7.1.7.1 indicates that the lifetime of the
PMK-R0 (and PMK-R1) is bound to the lifetime of PSK or MSK from which
the key was derived. This is currently stored in r0_key_lifetime, but
cache entries are not actually removed.
This commit uses the r0_key_lifetime configuration parameter when
wpa_auth_derive_ptk_ft() is called. This may need to be extended to use
the MSK lifetime, if provided by an external authentication server, with
some future changes. For PSK, there is no such lifetime, but it also
matters less as FT-PSK can be achieved without inter-AP communication.
The expiration timeout is then passed from R0KH to R1KH. The R1KH verifies
that the given timeout for sanity, it may not exceed the locally configured
r1_max_key_lifetime.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
FILS calls wpa_ft_store_pmk_r0() from wpa_auth.c. This is moved into a
new function wpa_ft_store_pmk_fils() in preparation of additional
information being needed.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Add a new configuration option ft_r0_key_lifetime that deprecates
r0_key_lifetime. Though, the old configuration is still accepted for
backwards compatibility.
This simplifies testing. All other items are in seconds as well. In
addition, this makes dot11FTR0KeyLifetime comment match with what got
standardized in the end in IEEE Std 802.11r-2008.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
There is no existing mechanism for setting up AP mode functionality with
FT enabled, so there is not really much point in having a build option
for trying to include the AP-to-AP FT functionality into wpa_supplicant
either. Since this build option results in failures to complete the
build, simply remove it completely. This can be restored if there is
ever desire to enable FT functionality in wpa_supplicant controlled AP
mode.
Signed-off-by: Jouni Malinen <j@w1.fi>
When wpa_supplicant is running on a Linux interface that is configured in
promiscuous mode, and it is not a member of a bridge, incoming EAPOL
packets are processed regardless of the Destination Address in the frame.
As a consequence, there are situations where wpa_supplicant replies to
EAPOL packets that are not destined for it.
This behavior seems undesired (see IEEE Std 802.1X-2010, 11.4.a), and can
be avoided by attaching a BPF filter that lets the kernel discard packets
having pkt_type equal to PACKET_OTHERHOST.
Signed-off-by: Davide Caratti <davide.caratti@gmail.com>
Previously we set this flag to one in wpa_supplicant_init_iface() if
Wi-Fi controller does not have a dedicated P2P-interface.
This setting had effect only in scope of wpa_supplicant_init_iface() and
it contradicts with comment to struct wpa_interface::p2p_mgmt field.
This comment says that this flag is used only if Wi-Fi controller has
dedicated P2P-device interface.
Also it contradicts with usage of similiar p2p_mgmt field in struct
wpa_supplicant. Again struct wpa_supplicant::p2p_mgmt is set only for
dedicated P2P-device interface.
After this change wpa_interface become input argument to
wpa_supplicant_init_iface() that we are not modifying.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
This fixes sending of FindStopped, GroupFormationFailure, and
InvitationReceived signals in the case of separate P2P-Device interface.
This extends the coverage of the earlier commit
745d62322b ("dbus: Redirect P2P request to
the managment device if present") to these three functions that were
missing the redirection.
Some wireless controllers might have separate P2P-Device interface, see
as example result of 'iw dev':
phy#0
Unnamed/non-netdev interface
...
type P2P-device
...
Interface wlp2s0
type managed
...
In this case there is separate 'struct wpa_supplicant' created for this
p2p-dev-* device as result of 'wpa_supplicant_add_iface >
wpas_p2p_add_p2pdev_interface > wpa_supplicant_add_iface'.
This instance of wpa_supplicant is not registered in D-Bus
(wpas_dbus_register_*) since for corresponding P2P device interface flag
'struct wpa_interface > p2p_mgmt' is set.
But this instance is saved in p2p_init_wpa_s and is used for handling
P2P related D-Bus commands. Therefore we should look for D-Bus path in
the parent of p2p_init_wpa_s instance.
Without this change test dbus_p2p_discovery starts failing if we set
support_p2p_device in vm-run.sh.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
If any of the interfaces supports FILS (and similarly for FILS-SK-PFS),
include the "fils" (and "fils_sk_pfs") capability in D-Bus information.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Add examples of relevant top level CONFIG clauses for wpa_supplicant
MACsec support to defconfig.
Extend the example of MACsec related network configuration. Also bring
them in line with the format of the other example network configurations.
Signed-off-by: Jaap Keuter <jaap.keuter@xs4all.nl>
When locating the position of the IGTK PN in the key data, we also need
to skip the KDE header, in addition to the keyid field. This fixes
hostapd RESEND_M3 and RESEND_GROUP_M1 behavior when PMF is negotiated
for the association. Previously, the IGTK KDE ended up getting
practically hidden since zeroing of the PN ended up clearing the KDE OUI
and Type fields.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
In the current implementation, upon an EAP method failure, followed by
an EAP failure, the EAP Status is propagated up in wpa_supplicant with a
general failure parameter string "failure". This parameter is used for a
notification on the dbus.
This commit reports the EAP method failure error code in a separate
callback.
The solution in this commit is generic to all EAP methods, and can be
used by any method that need to pass its error code. However, this
commit only implements the reporting for EAP-SIM and EAP-AKA methods
where the Notification Code (in AT_NOTIFICATION) is used as the method
specific error code value.
Signed-off-by: Ahmed ElArabawy <arabawy@google.com>
This is a regression test for a sequence where wpa_supplicant interface
MAC address is changed externally and the ifdown-ifup sequence is
processed only after the interface has already been set UP.
Signed-off-by: Jouni Malinen <j@w1.fi>
When connecting to a WPA-EAP network and the MAC address is changed
just before the association (for example by NetworkManager, which sets
a random MAC during scans), the authentication sometimes fails in the
following way ('####' logs added by me):
wpa_supplicant logs:
wlan0: WPA: RX message 1 of 4-Way Handshake from 02:00:00:00:01:00 (ver=1)
RSN: msg 1/4 key data - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: PMKID in EAPOL-Key - hexdump(len=22): dd 14 00 0f ac 04 d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
RSN: PMKID from Authenticator - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
wlan0: RSN: no matching PMKID found
EAPOL: Successfully fetched key (len=32)
WPA: PMK from EAPOL state machines - hexdump(len=32): [REMOVED]
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 66 20 cf ab 8c dc
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): ea 73 67 b1 8e 5f 18 43 58 24 e8 1c 47 23 87 71
RSN: Replace PMKSA entry for the current AP and any PMKSA cache entry that was based on the old PMK
nl80211: Delete PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKSA cache entry free_cb: 02:00:00:00:01:00 reason=1
RSN: Added PMKSA cache entry for 02:00:00:00:01:00 network_ctx=0x5630bf85a270
nl80211: Add PMKID for 02:00:00:00:01:00
wlan0: RSN: PMKID mismatch - authentication server may have derived different MSK?!
hostapd logs:
WPA: PMK from EAPOL state machine (MSK len=64 PMK len=32)
WPA: 02:00:00:00:00:00 WPA_PTK entering state PTKSTART
wlan1: STA 02:00:00:00:00:00 WPA: sending 1/4 msg of 4-Way Handshake
#### WPA: rsn_pmkid():
#### WPA: aa - hexdump(len=6): 02 00 00 00 01 00
#### WPA: spa - hexdump(len=6): 02 00 00 00 00 00
#### WPA: PMK - hexdump(len=32): b5 24 76 4f 6f 50 8c f6 a1 2e 24 b8 07 4e 9a 13 1b 94 c4 a8 1f 7e 22 d6 ed fc 7d 43 c7 77 b6 f7
#### WPA: computed PMKID - hexdump(len=16): d8 21 9d a5 73 98 88 26 ef 03 d2 ce f7 04 7d 23
WPA: Send EAPOL(version=1 secure=0 mic=0 ack=1 install=0 pairwise=1 kde_len=22 keyidx=0 encr=0)
That's because wpa_supplicant computed the PMKID using the wrong (old)
MAC address used during the scan. wpa_supplicant updates own_addr when
the interface goes up, as the MAC can only change while the interface
is down. However, drivers don't report all interface state changes:
for example the nl80211 driver may ignore a down-up cycle if the down
message is processed later, when the interface is already up. In such
cases, wpa_supplicant (and in particular, the EAP state machine) would
continue to use the old MAC.
Add a new driver event that notifies of MAC address changes while the
interface is active.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
