APs in 6 GHz operating with LPI/VLP rules will have significantly lower
SNR values compared to 2.4/5 GHz band APs. Earlier, the estimated
throughputs were used for comparison only when the delta of SNRs between
both the APs was not greater than 7 and as a result for comparing 6 GHz
APs with 2.4/5 GHz APs, estimated throughputs were not getting used.
The estimated throughput calculations takes SNR value also into
consideration, hence remove RSSI delta check if any of the APs are from
the 6 GHz band. This change is limited to the 6 GHz band only in order
to avoid possible regressions with 2.4/5 GHz APs.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
This makes it convenient for an external test script to use
ext_eapol_frame_io=1 to delay and/or modify transmission of EAPOL-Key
msg 1/4 without having to use separate frame injection mechanisms.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Prefer 6 GHz APs when estimated throughputs are equal with APs from the
2.4/5 GHz bands while selecting APs for connection. Also add a 6 GHz
specific noise floor default value for the 6 GHz band (with the same
value as was used for 5 GHz previously) to make this step clearer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to consider HE rates while estimating throughputs for the
scan results from HE enabled APs. HE 0.8 usec GI rates are used in all
tables. The minimum SNR values for HE rates (1024-QAM) are derived by
adding the existing minimum SNR values of 256-QAM rates from VHT tables
and the difference between the values of minimum sensitivity levels of
256-QAM rates and 1024-QAM rates defined in Table 27-51 (Receiver
minimum input level sensitivity) in IEEE P802.11ax/D8.0.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add support to calculate estimated throughputs for APs which support the
160 MHz (including 80+80 MHz) mode in VHT. The minimum SNR values for
VHT 160 MHz mode are derived from minimum SNR values used for VHT 80 MHz
mode + 3 dBm. The min-SNR values are derived relatively based on the
information that the minimum sensitivity levels defined in Table 21-25
(Receiver minimum input level sensitivity) in IEEE Std 802.11-2020 for
the 160 MHz mode are higher by 3 dBm compared to the values of the 80
MHz mode for each rate.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Add checks for features supported by the specific hardware mode of the
local device that has the channel for which the throughput is being
estimated instead of assuming the local device supports all optional
features. This is more accurate for cases where the local capabilities
might differ based on the band. In addition, this is in preparation for
extending rate estimates to cover optional VHT and HE features.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
When the driver provides a list of supported modes, chan6 ended getting
added even if the 2.4 GHz mode was not included. This resulted in
incorrect behavior of trying to transmit on a not supported channel in
case of 5 GHz only radios.
Fix this by adding the channel 6 by default only if the driver does not
provide a list of supported modes. Whenever the supported modes are
available, only add this channel if it is explicitly listed as an
enabled channel.
Fixes: 8e5739c3ac ("DPP2: Check channel 6 validity before adding it to chirp channel list")
Signed-off-by: Kani M <kanisumi@codeaurora.org>
Simplify the implementation by using shared functions for parsing the
capabilities instead of using various similar but not exactly identical
checks throughout the implementation.
Signed-off-by: Jouni Malinen <j@w1.fi>
IEEE Std 802.11-2020 mandates H2E to be used whenever an SAE password
identifier is used. While this was already covered in the
implementation, the sae_prepare_commit() function still included an
argument for specifying the password identifier since that was used in
an old test vector. Now that that test vector has been updated, there is
no more need for this argument anymore. Simplify the older non-H2E case
to not pass through a pointer to the (not really used) password
identifier.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Do so for both wpa_supplicant and hostapd. While this was not explicitly
required in IEEE P802.11az/D3.0, likely direction for the draft is to
start requiring use of H2E for all cases where SAE is used with PASN.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a PTK derivation is done as part of PASN authentication flow, a KDK
derivation should be done if and only if the higher layer protocol is
supported by both parties.
Fix the code accordingly, so KDK would be derived if and only if both
sides support Secure LTF.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Commit 3ab35a6603 ("Extend EAPOL frames processing workaround for
roaming cases") added a work around to address the issue of EAPOL frame
reception after reassociation replied to with an incorrect destination
address (the BSSID of the old AP). This is due to association events and
EAPOL RX events being reordered for the roaming cases with drivers that
perform BSS selection internally.
This mechanism relies on the fact that the driver always forwards the
EAPOL handshake to wpa_supplicant after the roaming (sets
last_eapol_matches_bssid during the EAPOL processing and resets on the
assoc/reassoc indication).
The above approach does not address the case where the driver does the
EAPOL handshake on the roam, indicating the authorized status to
wpa_supplicant but also forwards the EAPOL handshake to wpa_supplicant
for few other roam attempts. This is because the flag
last_eapol_matches_bssid is not set with the roam+authorized event from
the driver. Thus, the next reorder of roam and EAPOL RX events would
miss this workaround.
Address this by setting last_eapol_matches_bssid=1 on a roam+authorized
event from the driver.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
wpa_supplicant_ctrl_iface_deinit() was executed only if the
per-interface control interface initialization had been completed. This
is not the case if driver initialization fails and that could result in
leaving behind references to the freed wpa_s instance in a corner case
where control interface messages ended up getting queued.
Fix this by calling wpa_supplicant_ctrl_iface_deinit() in all cases to
cancel the potential eloop timeout for wpas_ctrl_msg_queue_timeout with
the reference to the wpa_s pointer. In addition, flush any pending
message from the global queue for this interface since such a message
cannot be of use after this and there is no need to leave them in the
queue until the global control interface gets deinitialized.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
This is a 2 octet field, so need to use WPA_GET_LE16() here instead of
using only the first octet of the value.
Fixes: bbd3178af4 ("MSCS: Add support to process MSCS Response frames")
Signed-off-by: Jouni Malinen <j@w1.fi>
Process the received comeback cookie and retry automatically if the AP
allows this. Otherwise, provide the cookie to upper layers to allow a
later attempt with the cookie.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
The new wpa_supplicant control interface command "PASN_DEAUTH
bssid=<BSSID>" can now be used to flush the local PTKSA cache for the
specified BSS and to notify the AP to request it to drop its PTKSA as
well.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
For testing purposes, add support for corrupting the MIC in PASN
Authentication frames for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
When a public key is included in the PASN Parameters element, it should
be encoded using the RFC 5480 conventions, and thus the first octet of
the Ephemeral Public Key field should indicate whether the public key is
compressed and the actual key part starts from the second octet.
Fix the implementation to properly adhere to the convention
requirements for both wpa_supplicant and hostapd.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
An EAPOL frame may be pending when wpa_supplicant requests to
deauthenticate. At this stage the EAP SM cache is already cleaned by
calling eapol_sm_invalidate_cached_session(). Since at this stage the
wpa_supplicant's state is still set to associated, the EAPOL frame is
processed and results in a crash due to NULL dereference.
This wasn't seen previously as nl80211 wouldn't process the
NL80211_CMD_CONTROL_PORT_FRAME, since wpa_driver_nl80211_mlme() would
set the valid_handler to NULL. This behavior was changed in commit
ab89291928 exposing this race.
Fix it by ignoring EAPOL frames while the deauthentication is in
progress.
Fixes: ab89291928 ("nl80211: Use process_bss_event() for the nl_connect handler")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Add the address family when manually constructing IPv4 addresses in
eapol_test on Windows. Otherwise other functions, like hostapd_ip_txt()
in src/utils/ip_addr.c, that rely on addr->af being set fail miserably.
The non-Windows option uses hostapd_parse_ip_addr() which does this as
part of the helper function.
Signed-off-by: Stefan Paetow <oss@eons.net>
This adds new control interface commands TWT_SETUP and TWT_TEARDOWN. For
now, these are only for testing purposes to be able to trigger
transmission of the TWT Action frames without configuring any local
behavior for TWT in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
The roam D-Bus and ROAM control itnerface commands flip the reassociate
bit before calling wpa_supplicant_connect(). wpa_supplicant connect
eventually aborts ongoing scans (if any), which causes scan results to
be reported. Since the reassociate bit is set, this will trigger a
connection attempt based on the aborted scan's scan results and cancel
the initial connetion request. This often causes wpa_supplicant to
reassociate to the same AP it is currently associated to instead of the
explicitly requested roaming target.
Add a roam_in_progress flag to indicate that we're currently attempting
to roam via an explicitly request to a specific BSS so that we don't
initiate another connection attempt based on the possibly received scan
results from a scan that was in progress at the time the roam command
was received.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
The wpa_ie buffer is now allocated here and needs to be freed before
returning from the function.
Fixes: d2ba0d719e ("Move assoc param setting into a helper function")
Signed-off-by: Jouni Malinen <j@w1.fi>
Use a shared code path for freeing the wpa_ie buffer to avoid
unnecessary complexity with a separate return for the non-FILS case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Build eap_*.so into the wpa_supplicant similarly with the wpa_supplicant
binary and include the shared helper functions from additional files
into the builds. This got broken at some point with the build system
changes.
Signed-off-by: Jouni Malinen <j@w1.fi>
These frames are used for verifying that a specific SA and protected
link is in functional state between two devices. The IEEE 802.11
standard defines only a case that uses individual MAC address as the
destination. While there is no explicit rule on the receiver to ignore
other cases, it seems safer to make sure group-addressed frames do not
end up resulting in undesired behavior. As such, drop such frames
instead of interpreting them as valid SA Query Request/Response.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
For an autonomous P2P group on the 5 GHz band, a channel was picked only
from the operating class 115 which is not available in the EU region
anymore. As a result, an autonomous group creation would always fail in
this generic 5 GHz channel case.
There are more possible available channels for the 5 GHz currently.
Especially in the EU region, the operating class 115 channels are no
longer available, but SRD channels (the operating class 124) are
available. Allow them to be used here if they are marked as allowed for
P2P GO use.
In addition, iterate through all the potential options instead of just
checking the first randomly picked channel. Start this iteration from
random position to maintain some randomness in this process.
Signed-off-by: Jimmy Chen <jimmycmchen@google.com>
Determine if the TDLS peer is HE capable based on HE Capability element
received in the TDLS Setup Response frame. Indicate the peer's HE
capabilities to the driver through sta_add().
Signed-off-by: Sreeramya Soratkal <ssramya@codeaurora.org>
The TX event for the next frame in the sequence might be received before
the TX status for the final GAS response frame is processed. This used
to result in the Config Result getting discarded and the negotiation not
completing successfully on the Configurator side.
Accept the Config Result message as an indication of the final GAS
response frame having went through fine even if the TX status has not
yet been processed to avoid this issue from a potential race condition
on kernel events.
Signed-off-by: Jouni Malinen <j@w1.fi>
Don't use 'protected' as the name of the variable in bss.h since this
might be used in control interfaces that use C++.
Fixes: 1c77f3d3f9 ("Indicate whether additional ANQP elements were protected")
Signed-off-by: Jouni Malinen <j@w1.fi>
These defines are for the capability bit number, not the binary value
from the bit index. As such, need to use BIT() here to set the bitmap
appropriately.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
extra_buf allocation was missed in one of the error cases.
Fixes: 170775232d ("ANQP: Add support to specify frequency in ANQP_GET command")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
When the driver SME is used, offloaded RSN handshakes like SA Query, GTK
rekeying, FT authentication, etc. would fail if wpa_supplicant enables
OCV in initial connection based on configuration but the driver doesn't
support OCV. To avoid such failures check the driver's capability for
enabling OCV when the driver SME used.
This commit also adds a capability flag for indicating OCV support
by the driver.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Set conf.force_kdk_derivation within the same if block as all the other
parameters. This is used only if ssid is not NULL, so no need to have
any special handling for this parameter.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Enabling beacon protection will cause STA connection/AP setup failures
if the driver doesn't support beacon protection. To avoid this, check
the driver capability before enabling beacon protection.
This commit also adds a capability flag to indicate beacon protection
support in client mode only.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Prior to this patch, we failed to recreate bit-by-bit identical
copies of wpa_supplicant because it doesn't generate reproducible manpages.
Since the latest version(0.6.14-3 or new) of docbook-utils have already
support getting the date from sgml file [1], it is possible to make some
progress on the "reproducible builds" effort [2].
[1]: https://sources.debian.org/patches/docbook-utils/0.6.14-3
[2]: https://reproducible-builds.org
Signed-off-by: Hu Keping <hukeping@huawei.com>
It was not easily possible to separate configuration of an interface and
credentials when using the configuration file instead of the control
interface or D-Bus interface for setting up the network profiles. This
makes it hard to distribute configuration across a set of nodes which
use wpa_supplicant without also having to store credentials in the same
file. While this can be solved via scripting, having a native way to
achieve this would be preferable.
Turns out there already is a framework to have external password
storages. It only had a single "test" backend though, which is kind of
an in-memory store which gets initialized with all passwords up front
and is mainly for testing purposes. This isn't really suitable for the
above use case: the backend cannot be initialized as part of the central
configuration given that it needs the credentials, and we want to avoid
scripting.
This commit thus extends the infrastructure to implement a new backend,
which instead uses a simple configuration file containing key-value
pairs. The file follows the format which wpa_supplicant.conf(5) uses:
empty lines and comments are ignored, while passwords can be specified
with simple `password-name=password-value` assignments.
With this new backend, splitting up credentials and configuration
becomes trivial:
# /etc/wpa_supplicant/wpa_supplicant.conf
ext_password_backend=file:/etc/wpa_supplicant/psk.conf
network={
ssid="foobar"
psk=ext:foobar
}
# /etc/wpa_supplicant/psk.conf
foobar=ecdabff9c80632ec6fcffc4a8875e95d45cf93376d3b99da6881298853dc686b
Alternative approaches would be to support including other configuration
files in the main configuration, such that common configuration and
network declarations including credentials are split up into separate
files. But the implementation would probably have been more complex
compared to reusing the already-existing framework for external password
backends.
Signed-off-by: Patrick Steinhardt <ps@pks.im>
The function wpa_config_get_line() is used by the wpa_supplicant config
file parser to retrieve the next non-comment non-blank line. We'll need
the same kind of functionality to implement the file-based external
password backend, so as a preparatory step this commit extracts the
function into its own standalone file in the utils package.
No functional changes are expected from this commit.
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Number of the P2P+NFC test cases have been failing every now and then
and those failures seemed to be because of having somehow managed to
select the GO's operating channel as HT40+ on the channel 11 in the 2.4
GHz band, i.e., something that is clearly incorrect. The P2P check for
HT40 secondary channel is supported only on the 5 GHz band, so drop HT40
configuration if it shows up unexpectedly on the 2.4 GHz band to avoid
issues in GO being able to start.
Signed-off-by: Jouni Malinen <j@w1.fi>
There's a chance that prior to config reload being requested a scan work
was started. As such forcing wpa_supplicant to WPA_DISCONNECTED was
removing any hints that the actual driver is busy with work. That led to
wpa_supplicant reporting "Failed to initialize AP scan" over and over
again for a few seconds (depending on driver/capabilities) until the
untracked scan finished.
Cancelling a scan isn't really a solution because there's a bunch of
scanning state bits sprinkled across wpa_supplicant structure and they
get updated as driver events actually flow in in async manner.
As far as I can tell this is only preventing unnecessary warning
messages. This doesn't seem like it was crippling any logic per se.
Signed-off-by: Michal Kazior <michal@plume.com>
The chirp scan could override the scan_res_handler. This could lead to
wpa_supplicant getting stuck in a scanning state while not scanning at
all until forced to, e.g., via an explicit SCAN control command.
The condition for trigerring this problem in my testing was when
(interface_count % 3) == 2. This introduced a two second delay before
actual scan was triggered after starting the wpa_supplicant instance up.
If DPP chirping was requested fast enough, in between the queueing and
triggering, it would punt the scan request, never to be resumed again.
Chirp scan handler wouldn't resume it leaving wpa_supplicant
inadvertently idle.
Signed-off-by: Michal Kazior <michal@plume.com>
Previously, the channel number was set in hostapd_freq_params only with
the presence of HT capabilities. Set the channel number before the check
for HT mode to accommodate the 6 GHz band cases.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
