There has been number of failures from this test case due to the
MESH-SAE-AUTH-FAILURE event from dev[0] and dev[1] arriving couple of
seconds after the one second timeout after the dev[2] events. This does
not look like a real issue, so increase the timeout to five seconds to
make this less likely to show false failures during testing.
Signed-off-by: Jouni Malinen <j@w1.fi>
The next commit modifies the BSS command behavior to report partial
results for a BSS, so mesh_scan_oom needs to allow a BSS entry to be
returned as long as it does not include the mesh information.
Signed-off-by: Jouni Malinen <j@w1.fi>
Check for MESH-PEER-CONNECTED from dev[1] before reporting MGMT-RX
timeout errors from dev[0]. This avoids false failures in case the short
0.01 s timeout at the end of the loop was not long enough to catch the
message.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that the Accepting Additional Mesh Peerings field is being
cleared properly when the maximum peer links count is reached.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is a regression test case to verify that MTK is calculated properly
also in this unexpected sequence.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This verifies that num_plinks is decremented properly if a peer mesh STA
reconnects without closing the link explicitly.
Signed-off-by: Jouni Malinen <j@w1.fi>
It seems to be possible for dev2 (the one with incorrect password) to
stop retries before either dev0 or dev1 reports the authentication
failure event. For now, allow the test case pass if either dev0 or dev1
reports the event rather than requiring both to report this. The
expected behavior can be fine-tuned in the future if the reporting
behavior is modified to be more consistent.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is more robust than checking the driver capability because it is
also possible for the wpa_supplicant build to be configured without mesh
support regardless of whether the driver supports it.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more convenient to run tests with wpa_supplicant builds
that do not support SAE (e.g., due to crypto library not providing
sufficient functionality for this).
Signed-off-by: Jouni Malinen <j@w1.fi>
This network profile parameter will be removed with the cleanup that
makes mesh use shared functions for setting channel parameters. That
will allow HT to be enabled automatically based on driver capabilities.
Signed-off-by: Jouni Malinen <j@w1.fi>
Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
The previous version was enabling all three stations at the same time
and left dev[1] and dev[2] competing on getting connected with dev[0]
that allowed only one pairing. This was not exactly robust and the pass
criteria depended on an extra event from either dev[1] or dev[2]. Fix
that by first connecting dev[0] and dev[1] and only after that, start
dev[2]. This allows proper validation of both the peering limit on
dev[0] and no extra event on dev[2].
Signed-off-by: Jouni Malinen <j@w1.fi>
Previously, these test cases were marked as failures, but it is nicer to
mark as skipped if the kernel does not include support for mesh.
Signed-off-by: Jouni Malinen <j@w1.fi>
If the initial Authentication frame was too early for the peer (i.e.,
NEW_PEER_CANDIDATE event arrived only after the Authentication frame),
wpas_mesh_open_no_auto and wpas_mesh_secure_no_auto test cases were
failing since they waited only for 10 seconds for the connection to be
completed while the retry timer was set to 10-20 seconds on the
authenticator side.
Signed-off-by: Jouni Malinen <j@w1.fi>
This function did not seem to do anything else apart from making it less
obvious that hwsim_utils.test_connectivity() is called.
Signed-off-by: Jouni Malinen <j@w1.fi>
This test case was failing every now and then due to dev1
(no_auto_peer=1) not receiving the new-peer-candidate event in time
before dev0 has already stopped retries on mesh peering open message.
This sounds somewhat expected with the default 4 * 40 ms = 160 ms
retries and 1000 TU beacon interval. Use maximum timeout 16 * 255 ms =
4080 ms to make this test case less likely to fail.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
hwsim_utils.test_connectivity() is already bidirectional test, so there
is no need to run it twice with the devices swapped for the second
iteration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible for some of the SAE test cases (e.g., ap_ft_sae) to fail
if they were run after the sae_groups test case that left the SAE group
configuration to a value that is not enabled by default. Fix this by
clearing sae_groups setting in the couple of test cases that were not
yet doing this.
Signed-off-by: Jouni Malinen <j@w1.fi>
Change the mesh tests to check for the presence of HT in the scan
results.
[original implementation by Chun-Yeow Yeoh <yeohchunyeow@gmail.com>]
[some fixes by Masashi Honma <masashi.honma@gmail.com>]
Signed-off-by: Ashok Nagarajan <ashok.dragon@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
This wpa_supplicant tests include basic tests for:
- Mesh scan
- Mesh group add/remove
- Mesh peer connected/disconnected
- Add/Set/Remove to test mesh mode network
- Open mesh connectivity test
- Secure mesh connectivity test
- no_auto_peer
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
[no_auto_peer test by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@gmail.com>
