These test caases depended on a single active scan round finding the AP.
It is possible for the Probe Response frame to get delayed sufficiently
to miss the response especially when testing under heavy load with
multiple parallel VMs. Allow couple of scan retries to avoid reporting
failures from these test cases.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Use the group SSID (if known) when requesting a join operation. This
makes some of the P2PS test cases more robust in cases where previously
executed tests have added older groups into the cached scan results with
the same MAC addresses and an incorrect BSS could have been picked
previously.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This makes it less likely to hit issues with running out of control
interface TX queue when running multiple FST test in a row. Number of
the FST operation sequences seemed to leave quite a few event messages
pending in one of the attached control interface sockets for wlan5 which
could result in test failure if the buffer space ran out and some of the
wpa_supplicant events were not delivered.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It is better to get these messages into the actual debug log instead of
hoping they will be noticed from stdout.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This test case used to leave the dynamically added wlan5 interface in a
state where it was still trying to reconnect to a network. This could
result in the following test cases being unable to clear the cfg80211
scan cache. Avoid this type of issues by explicitly stopping the
connection attempt and making sure that there are no scan results in the
cache at the end of connect_cmd_disconnect_event.
The following test case sequence triggered a failure due to the
remaining BSS table entry:
connect_cmd_disconnect_event connect_cmd_wep ap_hs20_random_mac_addr
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This parameter is used only in couple of test cases and there is no need
to maintain the code to reset it in WpaSupplicant::reset().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit a race condition between WPS_CANCEL and
immediately following WPS_PIN command. Wait for a disconnection event to
avoid that. This was seen with the following test case sequence:
ap_wpa2_psk_supp_proto_wrong_group_key_len ap_wps_probe_req_ie_oom
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
When running tests, make printk put all messages, including debug
messages, onto the serial console to go into the console file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wait for the AP-DISABLED and AP-ENABLED group events before reading the
current group operation frequency after P2P-REMOVE-AND-REFORM-GROUP.
This reduces a possibility of a race condition making a test case fail
with the returned frequency being 0 when reading this before the
reformed group is fully up. This may help avoid false error reports for
the following test cases: p2p_go_move_reg_change p2p_go_move_scm
p2p_go_move_scm_peer_supports p2p_go_move_scm_multi.
Signed-off-by: Jouni Malinen <j@w1.fi>
This is needed for number of EAP test cases at least when using the
internal TLS server implementation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Since wpa_supplicant is now retrying GAS comeback failures once, the
gas_anqp_oom_hapd test case started failing. Fix this by updating the
test case to expect success (on the retry).
Signed-off-by: Jouni Malinen <j@w1.fi>
This is in preparation of a wpa_supplicant change to allow GAS retries
which can result in the previous test case design showing failures due
to "unexpected" management frames (GAS Initial Request from the retry).
Signed-off-by: Jouni Malinen <j@w1.fi>
This adds some more test coverage for phase1 parameters that had not
previously been included in any of the test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
These test cases were supposed to clear the cfg80211 and wpa_supplicant
scan caches in the end to avoid causing issues to the following test
cases. This did not work properly after introduction of the support for
aborting a pending scan. Fix this by using the flush_scan_cache()
function and waiting within the test case until the final scan operation
completes.
This issue was triggered by ssid_hidden/ssid_hidden2 followed by
ext_password_interworking (though, not every time).
Signed-off-by: Jouni Malinen <j@w1.fi>
The rfkill initialization will be moved out from
wpa_driver_nl80211_drv_init() which would break one step in this OOM
test case due to the memory allocation not existing anymore. Fix this by
skipping that OOM step to avoid causing false failures with the
following commits.
Signed-off-by: Jouni Malinen <j@w1.fi>
This speeds up and clarifies error reporting for cases where the GO
fails to start in invitation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is useful for testing CRDA since it means you can use EPATH to
redirect the test scripts to a different crda binary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds more coverage for TDLS testing for a case where the direct
link should use various VHT channel bandwidths.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
