If CONFIG_WPS_STRICT is set, validate WPS IE(s) in management frames and
reject the frames if any of the mandatory attributes is missing or if an
included attribute uses an invalid value. In addition, verify that all
mandatory attributes are included and have valid values in the WSC
messages.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
The AP configuration may change after provisioning, so it is better
not to use the current security policy to prioritize results. Instead,
use WPS Selected Registrar attribute as the main sorting key and use
signal strength next without considering security policy or rate sets.
The non-WPS provisioning case remains as-is, i.e., this change applies
only when trying to find an AP for WPS provisioning.
wps_er_config can now be used to configure an AP. It is similar to
wps_er_learn, but instead of only learning the current AP settings,
it continues to send M8 with the new settings for the AP.
wps_er_start command now takes an optional parameter that can be used
to configure a filter to only allow UPnP SSDP messages from the
specified IP address. In practice, this limits the WPS ER operations
to a single AP and filters out all other devices in the network.
If the associating station indicates that it is intents to use WPS
by including WPS IE in (Re)Association Request frame, include WPS IE
in (Re)Association Response frame.
set_ap_wps_ie() is not used to set WPS IE for both Beacon and Probe
Response frames with a single call. In addition, struct wpabuf is used
instead of separate u8* and length fields. This avoids duplicated
allocation of the IEs and simplifies code in general.
This adds config_methods configuration option for wpa_supplicant
following the design used in hostapd. In addition, the string is
now parsed in common code from src/wps/wps_common.c and the list
of configurable methods include all the defined methods from
WPS 1.0h spec.
The use_psk_key parameter can now be used to force the Registrar to
use PSK format instead of ASCII passphrase when building a Credential
for the Enrollee. For now, this is not enabled, but it could be enabled
either based on external (to WPS) configuration or automatically set
based on some WPS attribute values from the Enrollee.
Instead of forcefully deinitializing ER immediately, give it some
time to complete unsubscription and call eloop_terminate() only once
ER code has completed its work.
Instead of using the latest selected registrar change, collect selected
registrar information separately from all registrars and use the union
of this information when building the WPS IE for Beacon and Probe
Response frames.
Note: SetSelectedRegistrar UPnP action does not include a unique
identifier, so the ER matching routine is based only on the IP address
of the ER. In theory, there could be multiple ERs using the same IP
address (but different port or URL), so there may be some corner cases
that would not always match the correct ER entry at the AP. Anyway, this
is not really expected to occur in normal use cases and even if it did
happen, the selected registrar information is not any worse than it was
before when only the last change from any registrar for being
advertized.
Use shared functions for converting Primary Device Type between binary
and string formats. In addition, use array of eight octets instead of a
specific structure with multiple fields to reduce code complexity.
The WPS 1.0h specification is quite unclear on what exactly should be
used as the MAC Address value in the Credential and AP Settings. It
looks like this should after all be the MAC Address of the Enrollee,
so change Registrar implementation to use that address instead of the
AP BSSID.
In addition, add validation code to the Enrollee implementation to
check the MAC Address value inside Credential (and also inside AP Settings)
to make sure it matches with the Enrollee's own address. However, since
there are deployed implementations that do not follow this interpretation
of the spec, only show the mismatch in debug information to avoid breaking
interoperability with existing devices.
This will need some additional code in wps_er_pbc() to handle PBC mode
enabling for a single AP only. For now, this can only be expected to work
when the ER is connected to a single AP.
New PINs can now be added to WPS ER. This results in the ER code
using SetSelectedRegistrar to modify AP state so that Enrollees
will be able to notice the actice registrar more easily.
This is the first step in adding support for using wpa_supplicant as a
WPS External Registrar to manage APs over UPnP. Only the device
discovery part is implemented in this commit.
This provides information about PBC mode result from the WPS Registrar
module. This could be used, e.g., to provide a user notification on the
AP UI on PBC failures.
Crypto library wrappers can now override the internal DH (group 5)
implementation. As a starting point, this is done with OpenSSL. The
new mechanism is currently available only for WPS (i.e., IKEv2 still
depends on the internal DH implementation).
Store a copy of device attributes during WPS protocol run and make it
available for external programs via the control interface STA MIB
command for associated stations. This gives access to device name and
type which can be useful when showing user information about associated
stations.
wpa_supplicant can now reconfigure the AP by acting as an External
Registrar with the wps_reg command. Previously, this was only used
to fetch the current AP settings, but now the wps_reg command has
optional arguments which can be used to provide the new AP
configuration. When the new parameters are set, the WPS protocol run
is allowed to continue through M8 to reconfigure the AP instead of
stopping at M7.
hostapd_cli wps_pin command can now have an optional timeout
parameter that sets the PIN lifetime in seconds. This can be used
to reduce the likelihood of someone else using the PIN should an
active PIN be left in the Registrar.
Windows XP and Vista clients can get confused about EAP-Identity/Request
when they probe the network with EAPOL-Start. In such a case, they may
assume the network is using IEEE 802.1X and prompt user for a
certificate while the correct (non-WPS) behavior would be to ask for the
static WEP key. As a workaround, use Microsoft Provisioning IE to
advertise that legacy 802.1X is not supported.
This seems to make Windows ask for a static WEP key when adding a new
network, but at least Windows XP SP3 was still marking IEEE 802.1X
enabled for the network. Anyway, this is better than just leaving the
network configured with IEEE 802.1X and automatic WEP key distribution.
The new file wps_nfc.c and ndef.c implements NFC device independent
operation, wps_nfc_pn531.c implements NFC device dependent operation.
This patch is only for the following use case:
- Enrollee = wpa_supplicant
- Registrar = hostapd internal Registrar
Following NFC methods can be used:
- Enrollee PIN with NFC
- Registrar PIN with NFC
- unencrypted credential with NFC
Encrypted credentials are not supported.
Enrollee side operation:
Registrar side operation:
Example configuration.
CONFIG_WPS=y
CONFIG_WPS_NFC=y
CONFIG_WPS_NFC_PN531=y
I used NFC device "NXP PN531". The NFC device access method is
confidential, so I used outer library. Please download below files from
https://www.saice-wpsnfc.bz/index.php
[WPS NFC Library]
WpsNfcLibrary/WpsNfc.h
WpsNfcLibrary/WpsNfcType.h
WpsNfcLibrary/WpsNfcVersion.h
WpsNfcLibrary/linux/libnfc_mapping_pn53x.dll
WpsNfcLibrary/linux/wpsnfc.dll
[NFC Reader/Writer Kernel Driver]
NFCKernelDriver-1.0.3/linux/kobj/sonyrw.ko
<WiFi test>
The hostapd/wpa_supplicant with this patch passed below tests on
"Wi-Fi WPS Test Plan Version 1.6".
4.2.5 Add device using NFC Method with password token
(I used SONY STA instead of NXP STA.)
4.2.6 Add device using NFC Method with configuration token
5.1.9 Add to AP using NFC Method with password token
through internal registrar
(I used SONY AP instead of NXP AP.)
5.1.10 Add to AP using NFC Method with configuration token
through internal registrar
Allow more than one pending PutWLANMessage data to be stored (M2/M2D
from multiple external Registrars) and drop pending M2/M2D messages when
the Enrollee replies with M3.
This adds mostly feature complete external Registrar support with the
main missing part being proper support for multiple external Registrars
working at the same time and processing of concurrent registrations when
using an external Registrar.
This code is based on Sony/Saice implementation
(https://www.saice-wpsnfc.bz/) and the changes made by Ted Merrill
(Atheros) to make it more suitable for hostapd design and embedded
systems. Some of the UPnP code is based on Intel's libupnp. Copyrights
and licensing are explained in src/wps/wps_upnp.c in more detail.
If a Registrar tries to configure the AP, but fails to validate the
device password (AP PIN), lock the AP setup after four failures. This
protects the AP PIN against brute force guessing attacks.
This optional configuration parameter can be used to override AP
Settings attributes in M7 similarly to extra_cred option for Credential
attribute(s) in M8.
This operation can now be moved into an external program by configuring
hostapd with wps_cred_processing=1 and skip_cred_build=1. A new
ctrl_iface message (WPS-REG-SUCCESS <Enrollee MAC addr> <UUID-E>) will
be used to notify external programs of each successful registration and
that can be used as a tricker to move from unconfigured to configured
state.
This makes it easier to pass the credential data to external programs
(e.g., Network Manager) for processing. The actual use of this data is
not yet included in hostapd/wpa_supplicant.
This callback is now used to stop wpa_supplicant from trying to continue
using parameters (most likely, device password) that do not work in a
loop. In addition, wpa_gui can now notify user of failed registration.
The event callback will be used for various event messages and the M2D
notification is the first such message. It is used to notify wpa_gui
about Registrar not yet knowing the device password (PIN).
Fragment WPS IE if needed to fit into the IE length limits in hostapd
and Reassemble WPS IE data from multiple IEs in wpa_supplicant.
In addition, moved WPS code from events.c into wps_supplicant.c to clean
up module interfaces.
These functions fit in better with the category of functions included in
wps.c. wps_common.c is now used for generic helper functions (currently,
only crypto code).
WPS IE is now passed from hostapd association processing into EAP-WSC
and WPS processing. Request Type attribute is parsed from this
information and if the request is for a WLAN Manager Registrar,
additional management keys are derived (to be used with UPnP).
Previously, wpa_supplicant as Enrollee case was handled using a
different callback function pointer. However, now that the wps_context
structure is allocated for all cases, the same variable can be used in
all cases.
This adds WPS support for both hostapd and wpa_supplicant. Both programs
can be configured to act as WPS Enrollee and Registrar. Both PBC and PIN
methods are supported.
Currently, hostapd has more complete configuration option for WPS
parameters and wpa_supplicant configuration style will likely change in
the future. External Registrars are not yet supported in hostapd or
wpa_supplicant. While wpa_supplicant has initial support for acting as
an Registrar to configure an AP, this is still using number of hardcoded
parameters which will need to be made configurable for proper operation.
