Commit graph

123 commits

Author SHA1 Message Date
Jouni Malinen
4be17ffbd9 Replace int status/reason_code with u16 variable
These cases are for the IEEE 802.11 Status Code and Reason Code and
those fields are unsigned 16 bit values, so use the more appropriate
type consistently. This is mainly to document the uses and to make the
source code easier to understand.

Signed-off-by: Jouni Malinen <j@w1.fi>
2019-04-22 22:08:07 +03:00
Mike Siedzik
2fc0675683 mka: Fix lowest acceptable Packet Number (LPN) calculation and use
The purpose of the Lowest Acceptable PN (lpn) parameters in the MACsec
SAK Use parameter set is to enforce delay protection. Per IEEE Std
802.1X-2010, Clause 9, "Each SecY uses MKA to communicate the lowest PN
used for transmission with the SAK within the last two seconds, allowing
receivers to bound transmission delays."

When encoding the SAK Use parameter set the KaY should set llpn and olpn
to the lowest PN transmitted by the latest SAK and oldest SAK (if
active) within the last two seconds. Because MKPDUs are transmitted
every 2 seconds (MKA_HELLO_TIME), the solution implemented here
calculates lpn based on the txsc->next_pn read during the previous MKPDU
transmit.

Upon receiving and decoding a SAK Use parameter set with delay
protection enabled, the KaY will update the SecY's lpn if the delay
protect lpn is greater than the SecY's current lpn (which is a product
of last PN received and replay protection and window size).

Signed-off-by: Michael Siedzik <msiedzik@extremenetworks.com>
2018-12-26 16:42:25 +02:00
Venkateswara Naralasetty
5abc7823bd wpa_supplicant: Add Multi-AP backhaul STA support
Advertise vendor specific Multi-AP IE in (Re)Association Request frames
and process Multi-AP IE from (Re)Association Response frames if the user
enables Multi-AP fuctionality. If the (Re)Association Response frame
does not contain the Multi-AP IE, disassociate.

This adds a new configuration parameter 'multi_ap_backhaul_sta' to
enable/disable Multi-AP functionality.

Enable 4-address mode after association (if the Association Response
frame contains the Multi-AP IE). Also enable the bridge in that case.
This is necessary because wpa_supplicant only enables the bridge in
wpa_drv_if_add(), which only gets called when an interface is added
through the control interface, not when it is configured from the
command line.

Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
2018-12-20 12:10:31 +02:00
Mathy Vanhoef
7f00dc6e15 Add driver API to get current channel parameters
This adds driver API functions to get the current operating channel
parameters. This encompasses the center frequency, channel bandwidth,
frequency segment 1 index (for 80+80 channels), and so on.

Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@cs.kuleuven.be>
2018-12-16 18:35:30 +02:00
Sunil Dutt
5ff39c1380 SAE: Support external authentication offload for driver-SME cases
Extend the SME functionality to support the external authentication.
External authentication may be used by the drivers that do not define
separate commands for authentication and association
(~WPA_DRIVER_FLAGS_SME) but rely on wpa_supplicant's SME for the
authentication.

Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
2018-02-02 21:17:55 +02:00
vamsi krishna
d98038bb05 FILS: Driver configuration to disable/enable FILS features
The new disable_fils parameter can be used to disable FILS functionality
in the driver. This is currently removing the FILS Capability bit in
Extended Capabilities and providing a callback to the driver wrappers.
driver_nl80211.c implements this using a QCA vendor specific command for
now.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-12-15 20:52:17 +02:00
Vidyullatha Kanchanapally
6338c99efa FILS: Send updated connection parameters to drivers if needed
After an initial connection wpa_supplicant derives ERP information which
can be used in doing eventual authentications in the same realm. This
information can be used by drivers with offloaded FILS support to do
driver/firmware initiated roamings. Add support to send this updated
information to such drivers.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-10-18 01:19:42 +03:00
Ashwini Patil
b04854ceff nl80211/MBO: Set temporary disallowed BSSID list to driver
Set temporary disallowed BSSID list to the driver so that the driver
doesn't try to connect to any of the blacklisted BSSIDs during
driver-based roaming operation. This commit includes support only for
the nl80211 driver interface using a QCA vendor command for this.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-06-30 17:27:44 +03:00
Vasanthakumar Thiagarajan
aa56e36d66 driver: Make DFS domain information available to core
Current DFS domain information of the driver can be used in ap/dfs
to comply with DFS domain specific requirements like uniform spreading
for ETSI domain.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
2017-05-13 20:01:44 +03:00
Vamsi Krishna
178553b709 MBO: Add support to set ignore assoc disallow to driver
Add support to set ignore assoc disallow to the driver so that the
driver ignores assoc disallowed bit set by APs while connecting. This is
used by drivers that handle BSS selection and roaming internally.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-05-05 00:26:05 +03:00
Vidyullatha Kanchanapally
6fbb54140b driver: Move add_pmkid() and remove_pmkid() arguments into a struct
This makes it easier to add more arguments to these wpa_driver_ops
functions.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-04-07 17:03:35 +03:00
Kanchanapally, Vidyullatha
3ab484928a nl80211: Driver command for checking BTM accept/reject
Add driver interface command using the QCA vendor extensions to check
the driverr whether to accept or reject a BSS transition candidate. For
the reject case, report an MBO reject reason code.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-03-07 00:20:29 +02:00
Jouni Malinen
c06fca04fd Add wpa_supplicant SET get_pref_freq_list_override
This can be used to override driver get_pref_freq_list() operation for
more convenient testing of preferred frequency list functionality.

Override string format:
<if_type1>:<freq1>,<freq2>,... <if_type2>:...

if_type: 0=STATION, 2=AP, 3=P2P_GO, 4=P2P_CLIENT, 8=TDLS, 9=IBSS

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2017-02-16 12:08:22 +02:00
Sunil Dutt
eeb34a432e nl80211: Enhance abort scan to also abort the vendor scan
This commit enhances the abort scan implementation to also abort the
vendor scan, if one was used to trigger the scan.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-11-30 19:33:39 +02:00
Sabrina Dubroca
1d3d0666a6 mka: Add enable_encrypt op and call it from CP state machine
This allows MKA to turn encryption on/off down to the driver.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-11-20 00:35:23 +02:00
Sabrina Dubroca
23c3528a84 mka: Add support for removing SAs
So that the core can notify drivers that need to perform some operations
when an SA is deleted.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-29 11:35:38 +03:00
Sabrina Dubroca
6f551abdfc mka: Remove "channel" hacks from the stack and the macsec_qca driver
This is specific to the macsec_qca driver. The core implementation
shouldn't care about this, and only deal with the complete secure
channel, and pass this down to the driver.

Drivers that have such limitations should take care of these in their
->create functions and throw an error.

Since the core MKA no longer saves the channel number, the macsec_qca
driver must be able to recover it. Add a map (which is just an array
since it's quite short) to match SCIs to channel numbers, and lookup
functions that will be called in every place where functions would get
the channel from the core code. Getting an available channel should be
part of channel creation, instead of being a preparation step.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-29 11:24:08 +03:00
Sunil Dutt
2e4e4fb71c nl80211: Allow TDLS trigger modes to be configured to the host driver
This commit adds a control interface command to configure the TDLS
trigger mode to the host driver. This TDLS mode is configured through
the "SET tdls_trigger_control" control interface command.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-10-27 23:22:33 +03:00
Sabrina Dubroca
a25e4efc9e mka: Add driver op to get macsec capabilities
This also implements the macsec_get_capability for the macsec_qca
driver to maintain the existing behavior.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-09 11:30:48 +03:00
Sabrina Dubroca
5f5ca28414 mka: Pass full structures down to macsec drivers' receive SC ops
Clean up the driver interface by passing pointers to struct receive_sc
down the stack to the {create,delete}_recevie_sc() ops, instead of
passing the individual properties of the SC.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-08 00:45:19 +03:00
Sabrina Dubroca
8ebfc7c2ba mka: Pass full structures down to macsec drivers' transmit SC ops
Clean up the driver interface by passing pointers to struct transmit_sc
down the stack to the {create,delete}_transmit_sc() ops, instead of
passing the individual arguments.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-08 00:45:03 +03:00
Sabrina Dubroca
cecdecdbe8 mka: Pass full structures down to macsec drivers' receive SA ops
Clean up the driver interface by passing pointers to struct receive_sa
down the stack to the {create,enable,disable}_receive_sa() ops, instead
of passing the individual properties of the SA.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-03 13:26:26 +03:00
Sabrina Dubroca
909c1b9835 mka: Pass full structures down to macsec drivers' transmit SA ops
Clean up the driver interface by passing pointers to struct transmit_sa
down the stack to the {create,enable,disable}_transmit_sa ops, instead
of passing the individual properties of the SA.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-03 13:17:21 +03:00
Sabrina Dubroca
7fa5eff8ab mka: Pass full structures down to macsec drivers' packet number ops
Clean up the driver interface by passing pointers to structs transmit_sa
and receive_sa down the stack to get_receive_lowest_pn(),
get_transmit_next_pn(), and set_transmit_next_pn() ops, instead of
passing the individual arguments.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-10-03 12:54:08 +03:00
Sabrina Dubroca
07a6bfe1d2 mka: Store cipher suite ID in a u64 instead of u8 pointer
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-08-28 21:55:54 +03:00
Sabrina Dubroca
ec958aee32 mka: Remove cs_len argument from the set_current_cipher_suite functions
This is a known constant value (CS_ID_LEN, i.e., the length of the EUI64
identifier) and does not need to be provided separately in these
function calls.

Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
2016-08-28 20:55:34 +03:00
vamsi krishna
cc9985d1b1 Set default scan IEs to the driver (QCA vendor extension)
This makes wpa_supplicant set default scan IEs to the driver (if the
vendor command is supported). The driver can use these IEs in the scan
requests initiated by the driver itself. Also the driver can merge these
IEs into further scan requests that it receives, in case if the scan
request doesn't carry any of the IEs sent in this command.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-08-02 21:21:52 +03:00
Peng Xu
a6f5b1937a P2P: Allow P2P listen being offloaded to the driver/firmware
This allows P2P Listen to be offloaded to device to enhance power
saving.

To start P2P listen offload, from wpa_cli interface, issue the command:
	p2p_lo_start <freq> <period> <interval> <count>

To stop P2P listen offload, issue the command:
	p2p_lo_stop

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-07-03 22:36:58 +03:00
Jouni Malinen
f868d5607d mesh: Clean up AMPE element encoding and parsing
The AMPE element includes number of optional and variable length fields
and those cannot really be represented by a fixed struct
ieee80211_ampe_ie. Remove the optional fields from the struct and
build/parse these fields separately.

This is also adding support for IGTKdata that was completely missing
from the previous implementation. In addition, Key RSC for MGTK is now
filled in and used when configuring the RX MGTK for a peer.

Signed-off-by: Jouni Malinen <j@w1.fi>
2016-06-19 20:18:09 +03:00
Kanchanapally, Vidyullatha
cc9a2575ca nl80211: Use extended capabilities per interface type
This adds the necessary changes to support extraction and use of the
extended capabilities specified per interface type (a recent
cfg80211/nl80211 extension). If that information is available,
per-interface values will be used to override the global per-radio
value.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2016-05-31 21:35:54 +03:00
Matti Gottlieb
e42adb9a75 driver: Add a packet filtering function declaration
Add a new function declaration that will allow wpa_supplicant to request
the driver to configure data frame filters for specific cases.

Add definitions that will allow frame filtering for stations as
required by Hotspot 2.0:

1. Gratuitous ARP
2. Unsolicited NA
3. Unicast IP packets encrypted with GTK

Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
2016-04-08 13:13:55 +03:00
Avraham Stern
09ea4309b6 nl80211: Add support for multiple scan plans for scheduled scan
Add 'scan plans' to driver scan parameters for scheduled scan.
Each 'scan plan' specifies the number of iterations to run the scan
request and the interval between iterations. When a scan plan
finishes (i.e., it was run for the specified number of iterations),
the next scan plan is executed. The last scan plan will run
infinitely.

The maximum number of supported scan plans, the maximum number of
iterations for a single scan plan and the maximum scan interval
are advertised by the driver.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-11-30 14:03:28 +02:00
Kanchanapally, Vidyullatha
4f30addb38 nl80211: Add support for aborting an ongoing scan
This adds the driver interface commands for issuing a request to abort
an ongoing scan operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-11-26 19:44:14 +02:00
Avraham Stern
d8a3b66d7f driver: Make setting up AP optional when creating AP interface
When an AP interface it created, it is also setup and subscribes
for management frames etc. However, when the interface is added by
wpa_supplicant, setting up for AP operations is redundant because
it will be done by wpa_supplicant on wpa_drv_init() when setting
the interface mode to AP.

In addition, it may cause wpa_supplicant to fail initializing the
interface as it will try to subscribe for management frames on this
interface but the interface is already registered.

Change this, so when adding an AP interface, make setting up the AP
optional, and use it only when the interface is added by hostapd but not
when it is added by wpa_supplicant.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
2015-11-22 17:42:59 +02:00
Andrei Otcheretianski
2d3943ce5b nl80211: Specify CSA offsets in send_mlme() driver op
Some management frames contain CSA counters which should be updated by
kernel. Change driver op send_mlme() allowing to send a frame,
specifying an array of offsets to the CSA counters which should be
updated. For example, CSA offsets parameters should be specified when
sending Probe Response frames during CSA period.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
2015-10-03 21:07:35 +03:00
Jouni Malinen
34c5267bbc Return error from wpa_drv_get_pref_freq_list() if no driver support
Commit 983422088f ('nl80211: Add means to
query preferred channels') return success if no driver wrapper callback
was provided for fetching the preferred channel list. That is
problematic since the *num argument is not updated and uninitialized
freq_list could end up getting used with arbitrary frequency values. Fix
this by returning error in case the values were not available due to
driver wrapper not implementing the function. This matches the style
used in the driver_nl80211.c implementation for the case where the
driver does not support such fetch operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-30 22:13:47 +03:00
Ahmad Kholaif
983422088f nl80211: Add means to query preferred channels
Extend the QCA vendor specific nl80211 interface to query the preferred
frequency list from driver and add a new wpa_cli command to query this
information.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-29 19:46:31 +03:00
Ahmad Kholaif
7c813acf9c P2P: Inform driver of the operating channel following group formation
Upon GO Negotiation completion, if the remote peer becomes GO, send a
hint event over QCA vendor specific interface to inform the driver of
the likely operating channel of the P2P GO.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-29 19:10:16 +03:00
Srinivas Dasari
844dfeb804 QCA vendor command support to set band to driver
Add vendor command to pass SET setband command to the driver and read
the updated channel list from driver when this notification succeeds.
This allows the driver to update its internal channel lists based on
setband configuration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-07-28 21:00:18 +03:00
Andrei Otcheretianski
0799b3f899 P2P: Specify frequency when sending Probe Response frame
If the RX frequency of the Probe Request frame is known, specify it when
sending the Probe Response frame. This is needed when the Probe Request
frame is received on another virtual interface, for example, when a GO
or P2PS client are discoverable on the group operating channel.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Andrei Otcheretianski
5d180a7739 drivers: Add freq parameter to send_mlme() function
Change send_mlme() API to allow sending management frames on a specific
channel, overriding the internal driver decision.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
2015-06-14 23:16:55 +03:00
Eliad Peller
e7a296ba13 Remove unused shared_freq driver op
This driver op is not used anymore

Signed-off-by: Eliad Peller <eliad@wizery.com>
2015-03-20 15:56:59 +02:00
Jouni Malinen
98cd3d1c3b Preparations for variable length KCK and KEK
This modifies struct wpa_ptk to allow the length of KCK and KEK to be
stored. This is needed to allow longer keys to be used, e.g., with
Suite B 192-bit level.

Signed-off-by: Jouni Malinen <j@w1.fi>
2015-01-27 01:26:49 +02:00
Jouni Malinen
911942ee64 Add a test framework for various wpa_supplicant failure cases
For CONFIG_TESTING_OPTIONS=y builds, add a new test parameter than can
be used to trigger various error cases within wpa_supplicant operations
to make it easier to test error path processing. "SET test_failure
<val>" is used to set which operation fails. For now, 0 = no failures
and 1 = scan trigger fails with EBUSY. More operations can be added in
the future to extend coverage.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2015-01-19 19:34:00 +02:00
Arik Nemtsov
6b90deae4d TDLS: Propagate enable/disable channel-switch commands to driver
The supplicant code does not try to control the actual channel of the
radio at any point. It simply passes the target peer and channel
parameters to the driver. It's the driver's responsibility to
periodically initiate TDLS channel-switch operations when TDLS
channel-switching is enabled.

Allow enable/disable operations to be invoked via the control interface.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2015-01-04 20:30:11 +02:00
Jouni Malinen
2961bfa8e1 Remove unused send_eapol() driver op
The send_eapol() callback was used by driver_test.c, but with that
removed, there is no remaining users of the alternative EAPOL frame
transmitting mechanism in wpa_supplicant, i.e., all remaining driver
interfaces use l2_packet instead. Remove the send_eapol() to get rid of
unused code.

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-11 15:40:07 +02:00
Jouni Malinen
8105821b39 Replace send_ft_action() driver_op with send_action()
This reduced number of unnecessarily duplicated driver interface
callback functions for sending Action frames by using the more generic
send_action() instead of FT specific send_ft_action().

Signed-off-by: Jouni Malinen <j@w1.fi>
2014-12-06 18:13:29 +02:00
Moshe Benji
471cd6e10c WMM AC: Add add_tx_ts and del_tx_ts driver ops
Add add_tx_ts() and del_tx_ts() ops to notify the driver about
TSPEC add / delete.

Additionally, add wmm_ac_supported flag to indicate
whether the driver supports WMM AC.

Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
2014-11-16 20:47:36 +02:00
Bob Copeland
6c1664f605 nl80211: Add new commands to support mesh interfaces
Create init_mesh, mesh_join, and mesh_leave actions to kernel.

Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Jason Mobarak <x@jason.mobarak.name>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
2014-10-19 12:58:13 +03:00
Arik Nemtsov
984dadc23a TDLS: Set the initiator during tdls_mgmt operations
Some drivers need to know the initiator of a TDLS connection in order
to generate a correct TDLS mgmt packet. It is used to determine
the link identifier IE. Pass this information to the driver.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
2014-10-03 11:52:21 +03:00