This function can be used to clean up local UNIX domain socket files
that may be left over from clients that were previously connected to
wpa_supplicant. At least for now, this is only available for Android
builds.
This adds the basic mechanism for running through network selection:
scan, ANQP fetch, network selection, and connection. Actual rules for
network selection and the creation of the network block are still
missing, but will be added in separate commits.
"hostapd_cli ess_disassoc (STA addr) (URL)" can now be used to send
an ESS Dissassociation Imminent notification to the STA. This event
is shown in wpa_supplicant ctrl_iface monitors (e.g., wpa_cli):
"WNM: ESS Disassociation Imminent - session_info_url=http://example.com/session/"
The new wpa_supplicant.conf file global parameters interworking and
hessid can be used to configure wpa_supplicant to include
Interworking element in Probe Request frames.
GAS/ANQP is a generic protocol and in no way specific to P2P, so move
routines used to build GAS/ANQP frames to a separate file that can be
shared for other uses than just P2P service discovery.
These can be used in some cases with a bitfield having multiple
AKMs enabled (e.g., WPA-PSK and WPA-PSK-SHA256). Address those
cases by checking whether any of the matching AKM are included.
CFLAGS += -DCONFIG_RSN_TESTING in .config and rsn_testing=1 in
hostapd.conf can now be used to enable a testing mode that adds
extensions to RSN element. This can be used to check whether
station implementations are incompatible with future extensions
to the RSN element.
Build options can now be used to replace the location of client
sockets for UNIX domain socket control interface:
CFLAGS += -DCONFIG_CTRL_IFACE_CLIENT_DIR=\"/tmp\"
CFLAGS += -DCONFIG_CTRL_IFACE_CLIENT_PREFIX=\"wpa_ctrl_\"
tdls_prohibit=1 and tdls_prohibit_chan_switch=1 and now be used to
disable use of TDLS or TDLS channel switching in the BSS using
extended cabilities IE as defined in IEEE 802.11z.
CONFIG_WPS_REG_DISABLE_OPEN=y can be used to configure wpa_supplicant
to disable open networks by default when wps_reg command is used to
learn the current AP settings. When this is enabled, there will be a
WPS-OPEN-NETWORK ctrl_iface event and the user will need to explicitly
enable the network (e.g., with "select_network <id>") to connect to
the open network.
The nl80211 driver can report low ACK condition (in fact it reports
complete loss right now only). Use that, along with a config option, to
disconnect stations when the data connection is not working properly,
e.g., due to the STA having went outside the range of the AP. This is
disabled by default and can be enabled with disassoc_low_ack=1 in
hostapd or wpa_supplicant configuration file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no point in maintaining two almost identical versions
of this parser. Move WPA IE parser into wpa_common.c similarly
to what was already the case with RSN IE parse.
Commit d8d940b746 introduced a regression
that prevented TSN APs from being used with WEP since the AP was
rejected if it advertised WPA or RSN IE when we were configured to use
WEP. Resolve this by checking whether the AP is advertising a TSN, i.e.,
whether the AP allows WEP to be used as a group cipher. If so, allow
the AP to be selected if we are configured to use static WEP or
IEEE 802.1X (non-WPA).
It should be noted that this is still somewhat more restricted in AP
selection than earlier wpa_supplicant branches (0.7.x or older) that
ignore the WPA/RSN IE completely when configured for non-WPA.
This tool can be used to capture IEEE 802.11 frames either from a
monitor interface for realtime capturing or from pcap files for
offline analysis. This version is only adding basic infrastructure for
going through the frames and parsing their headers.
A separate build number (etc.) version number postfix can now be
added to the build without having to modify source code files by
defining VERSION_STR_POSTFIX. This can be done, e.g., by adding
following line to .config:
CFLAGS += -DVERSION_STR_POSTFIX=\"-foo\"
If enabled, cross connection allows GO to forward IPv4 packets
using masquerading NAT from the P2P clients in the group to an
uplink WLAN connection. This is disabled by default and can be
enabled with "wpa_cli p2p_set cross_connect 1" on the P2P device
interface.
Advertize list of authorized enrollee MAC addresses in Beacon and
Probe Response frames and use these when selecting the AP. In order
to provide the list, the enrollee MAC address should be specified
whenever adding a new PIN. In addition, add UUID-R into
SetSelectedRegistrar action to make it potentially easier for an AP
to figure out which ER sent the action should there be multiple ERs
using the same IP address.
This patch adds support for wired IEEE 802.1X client on the Solaris.
I have tested with these:
OS : OpenSolaris 2009.06
EAP : EAP-MD5
Switch : Cisco Catalyst 2950
A new hostapd_cli command, wps_ap_pin, can now be used to manage
AP PIN at runtime. This can be used to generate a random AP PIN and
to only enable the AP PIN for short period (e.g., based on user
action on the AP device). Use of random AP PIN that is only enabled
for short duration is highly recommended to avoid security issues
with a static AP PIN.
As a compromise between usability and security, do not disable
AP PIN permanently based on failed PIN validations. Instead, go to
AP Setup Locked state for increasing amount of time between each
failure to slow down brute force attacks against the AP PIN.
This avoids problems with some external Registrars that may try
to use the same PIN multiple times without user input. Now, the
user will still be able to fix the PIN and try again later while
a real attack is delayed enough to make it impractical.
