Instead of returning "skip" from the test function, raise the new
HwsimSkip exception to indicate a test case was skipped.
Signed-off-by: Jouni Malinen <j@w1.fi>
It was possible for regulatory domain changes to "leak" into following
test cases in number of cases where the cfg80211 BSS table remained
after regulatory domain had been restored to world roaming. Try to make
this less likely to occur by explicitly clearing BSS table at the end of
test cases that use different regulatory domain. This makes P2P test
cases that verify channel selection based on world roaming rules more
robust.
Signed-off-by: Jouni Malinen <j@w1.fi>
This avoids one more cleanup step between most test cases by stopping ER
only in case it was actually used during a test.
Signed-off-by: Jouni Malinen <j@w1.fi>
A single channel scan just before WPS_REG, WPS_PBC, and WPS_PIN commands
can be used to avoid having to run a full scan. This saves significant
amount of time in the WPS test cases.
Signed-off-by: Jouni Malinen <j@w1.fi>
This makes it more convenient and consistent to clear the cached scan
results from cfg80211 and wpa_supplicant.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The "Not fully connected" report did not clearly identify what went
wrong, so make this more verbose in hope of being able to determine what
happened should this test case fail again.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
It was possible to hit the 10 second timeout in some test cases under
heavy load (e.g., with large number of VMs running tests in parallel).
These timeouts are not really indicating any real error, so make them
less likely to show up in reports by increasing the connection timeout
to 30 seconds.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This is needed in preparation for WPS AES being mapped to enabling both
CCMP and GCMP if the driver supports both ciphers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
The scan for WPS-AUTH validation may miss a Probe Response frame if the
hostapd process gets blocked under load, e.g., when testing with
parallel-vm.sh.
Signed-off-by: Jouni Malinen <j@w1.fi>
Scan explicitly for the AP that may be started during the test case
execution. This is needed to work around issues where under heavy CPU
load, the single active scan round may miss the delayed Probe Response
from the second AP.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the scan to miss a Probe Response frame especially
under heavy load, so try again to avoid reporting invalid failures.
Signed-off-by: Jouni Malinen <j@w1.fi>
It is possible for the final step of the test case to fail under load
(e.g., when using parallel-vm.sh with large number of VMs), so run
through additional scan iterations if the WPS-AUTH flag does not get
removed immediately.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
This can fail if Probe Response frame is missed and Beacon frame was
used to fill in the BSS entry. This can happen, e.g., during heavy load
every now and then and is not really an error, so try to workaround by
runnign another scan.
Signed-off-by: Jouni Malinen <j@w1.fi>
run-tests.py now takes an optional --long parameter that can be used to
enable running of test cases that take a long time (multiple minutes).
By default, such test cases are skipped to avoid making the normal test
run take excessive amounts of time.
As an initial long test case, verify WPS PBC walk time expiration (two
minutes).
Signed-off-by: Jouni Malinen <j@w1.fi>
Wait a bit between WPS_CONFIG command and the first scan. This can avoid
an extra five second wait due to having to scan again if the initial
scan operations happens to be quick enough to happen before the AP has
updated its configuration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Only run-tests.py is actually executed, so there is no need to specify
the interpreter in all the helper files and test script files.
Signed-off-by: Jouni Malinen <j@w1.fi>
