Commit graph

7381 commits

Author SHA1 Message Date
Jouni Malinen
fdb45355d4 WPS: Extend per-station PSK to support ER case as well
When wpa_psk_file is used instead of wpa_psk/wpa_passphrase, each WPS
Enrollee was given a unique PSK. This did not work for the
station-as-Registrar case where ER would learn the current AP settings
instead of enrolling itself (i.e., when using the AP PIN instead of
station PIN). That case can be covered with a similar design, so
generate a per-device PSK when building M7 as an AP in wpa_psk_file
configuration.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-13 18:22:25 +02:00
Jouni Malinen
e6c96df8b6 tests: Verify PMF association comeback and STA initiated SA Query
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-13 18:22:25 +02:00
Jouni Malinen
9a1a538fa5 wpa_supplicant AP: Allow PMF to be enabled with ieee80211w
The ieee80211w parameter was not previously copied to the hostapd BSS
structure from wpa_supplicant configuration, so PMF was practically
disabled. Allow it to be configured through the wpa_supplicant network
configuration block.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-13 18:22:25 +02:00
Jouni Malinen
ce6b9cd482 Allow reason code to be specified for DEAUTH/DISASSOC test frame
hostapd DEAUTHENTICATE and DISASSOCIATE control interface commands
accepted both a test=<0/1> and reason=<val> parameters, but these were
not supported in the same command as a combination. Move the code around
a bit to allow that as well since it can be helpful for automated test
scripts.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-13 01:26:09 +02:00
Jouni Malinen
7cd0aa7ea8 tests: VHT functionality
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 22:39:18 +02:00
Sunil Dutt
dda8be7114 TDLS: Use QoS info from WMM IE obtained in TDLS frames
TDLS Setup Request/Response frames from the peers include the WMM IE,
hence parse the same and consider the QoS Info from the WMM IE. The
qos_info obtained in the WMM IE overwrites the one obtained through
WLAN_EID_QOS attribute.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 22:39:11 +02:00
Jouni Malinen
daa70bdf68 Fix CONFIG_NO_SCAN_PROCESSING=y build
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 22:39:11 +02:00
Sunil Dutt Undekari
3a8ec7382e P2P: Report dev_found event (if not yet done) from GO Neg Req RX
p2p_find removes P2P_DEV_REPORTED flag from every existing P2P peer
entry. Thus, if a GO Negotiation Request frame is received before the
peer is re-discovered based on Probe Response frame, report
P2P-DEVICE-FOUND indication prior to the P2P-GO-NEG-REQUEST similarly to
how this is done the first time the peer is found.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 22:39:11 +02:00
Jouni Malinen
aa034377f7 tests: TKIP countermeasures
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 22:39:11 +02:00
Jouni Malinen
f8ad9dc21a tests: Check for AP-DISABLED when setting up AP
This allows a critical error to be noticed more quickly and reported
more clearly in the test log.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 13:55:05 +02:00
Jouni Malinen
0f23a5e7d6 Mark AP disabled if initialization steps fail
Previously, some of the last initialization steps could fail without
clearly marking the interface disabled. For example, configuring the
channel to the driver could fail, but hostapd would not clearly identify
as the interface not being in functional state apart from not moving it
to the ENABLED state. Send an AP-DISABLED event and mark interface state
DISABLED if such a setup operation fails.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 13:55:05 +02:00
Jouni Malinen
c2149b08da tests: Wait longer for hostapd REMOVE command to complete
Some kernel debugging options (especially
CONFIG_DEBUG_KOBJECT_RELEASE=y) can add significant blocking time to
interface removal with NL80211_CMD_DEL_INTERFACE and
SIOCGIFBR(BRCTL_DEL_BRIDGE) block for 1-8 seconds. This could result in
the VLAN test cases failing due to a wpaspy timeout on the REMOVE
command even though the issue was only in the kernel debugging code
making the operations significantly slower. Work around this by using a
longer timeout for that control interface command to allow this type of
debug kernel to be used.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 11:42:59 +02:00
Jouni Malinen
39b420f7b1 HS 2.0R2: Add parse_cert command for debugging purposes
This hs20-osu-client client command can be used to parse a DER encoded
X.509v3 certificate with the logotype extensions and
id-wfa-hotspot-friendlyName values shown in detail.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:22 +02:00
Jouni Malinen
c0d701a347 HS 2.0R2: Add OSU client implementation
This adds a reference implementation of Hotspot 2.0 Release 2 OSU
client. While this implements all of the required functionality, it is
likely that a significant extensions would be used to integrate this
with user interfaces and operating system configuration components.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:22 +02:00
Jouni Malinen
d2bb2b4681 Add os_file_exists()
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:22 +02:00
Jouni Malinen
1cb3eda954 HS 2.0R2: Add wrapper functions for libcurl
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:22 +02:00
Jouni Malinen
2cb8f96789 HS 2.0R2: Add wrapper functions for libxml2
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:22 +02:00
Jouni Malinen
da4ec2c71a HS 2.0R2: Add wrapper for system browser
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:22 +02:00
Jouni Malinen
db3ca20ec8 HS 2.0R2: Add wrapper for wpadebug browser on Android
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:21 +02:00
Jouni Malinen
2a10e57201 HS 2.0R2: Add wrapper for Android browser for user interaction
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:21 +02:00
Jouni Malinen
d0b79d74b6 HS 2.0R2: Add wrapper functions for WebKit
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:21 +02:00
Jouni Malinen
91728f2f12 Add wpa_ctrl helper functions for upper level functionality
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:21 +02:00
Jouni Malinen
b4c26ef997 Clean up hostapd_config_fill() parsers
Some of the parsing code was using a bit too complex design and could be
simplified after the earlier return-on-error cleanups.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:21 +02:00
Jouni Malinen
b2e32cde83 Fix memory leaks on wpa_config_parse_string() error paths
hostapd configuration parser did not free the temporary buffer on some
error paths.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:21 +02:00
Jouni Malinen
a0b728b7e2 Simplify hostapd_config_fill() error reporting
There is no need for trying to count the number of errors in this
function since this is not a loop anymore and the return value will be
either 0 or 1.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:21 +02:00
Jouni Malinen
599f40db7d Remove extra indentation level from hostapd_config_fill()
The configuration file parsing routines were moved to a separate
function a while back, but left at the old indentation level to avoid
showing large diffs in the commit and to avoid conflicts with parallel
development in other branches. There is never a perfect time for this
type of changes, but we might as well finally get rid of that extra
indentation now with Hotspot 2.0 Rel 2 changes pulled in.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-12 01:09:15 +02:00
Jouni Malinen
99cd77a8c5 tests: Verify reassociate-to-same-BSS commands
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-11 20:08:18 +02:00
Jouni Malinen
e8d70a739b nl80211: Hide deauth event due to forced deauth-during-auth
If NL80211_CMD_AUTHENTICATE fails due to exiting authentication, forced
deauthentication is used to clear cfg80211 start and a new
authentication command is retried. This resulted in an extra
disconnection event getting delivered to the core wpa_supplicant code
and that could end up confusing state there, e.g., by clearing
connection parameters like wpa_s->key_mgmt and preventing the following
association from reaching proper COMPLETED state with open networks.

Fix this by hiding the unnecessary disconnection event when using the
deauth-for-auth workaround.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-11 20:02:23 +02:00
Peter Qiu
0f44ec8eba Add a reattach command for fast reassociate-back-to-same-BSS
Add "reattach" command to perform single-channel single-ssid scan
instead of full scan when trying to reconnect to the currently
"connected" network (assuming old scan results are not current enough to
skip the scan completely). This allows the scan result to come back in
much faster time. In ath9k, the scan took around 12 seconds with full
background scan, and only 0.1 second with the single-channel single-ssid
scan. Thus, take much less time for the client to re-establish
connection with the currently "connected" network.

Signed-hostap: Peter Qiu <zqiu@chromium.org>
2014-03-11 19:38:01 +02:00
Ben Greear
cfc393a645 hostapd: Document interworking realm EAP Method types
Add link to the EAP type definitions document.

Signed-hostap: Ben Greear <greearb@candelatech.com>
2014-03-11 19:27:55 +02:00
Ben Greear
7450c1287d DFS: Add extra debugging messages
This might help someone realize why their hostapd config isn't working
properly.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2014-03-11 19:26:48 +02:00
Ben Greear
5d0d72a3e5 wpa_supplicant: Put upper bound on initial scan time delay
This makes stations associate much faster when using lots of stations.
In addition, this avoids delaying the initial scan continuously for
dynamic interface removal/addition cases.

Signed-hostap: Ben Greear <greearb@candelatech.com>
2014-03-11 19:23:17 +02:00
Moshe Benji
8c06db703d nl80211: Fix P2P Device handling when starting with RF-kill blocked
On RF-kill, we should not request the kernel to start a P2P device. In
addition, we should call i802_set_iface_flags() both for a P2P Device
interface and any other interface instead of calling a dedicated
function for each.

Signed-off-by: Moshe Benji <Moshe.Benji@intel.com>
2014-03-11 19:22:03 +02:00
Alexander Bondar
5e3ddf4d23 PNO: Change sched_scan_stopped event to handle pending PNO properly
When a sched_scan_stopped event is received and there is a pending PNO,
it used regular scheduled scan parameters instead of PNO specific
parameters. Change it by calling wpas_start_pno().

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-11 19:15:48 +02:00
Alexander Bondar
737e7a08b0 PNO: Move and rename pno_start()/pno_stop()
Move pno_start() and pno_stop() to scan.c as a more relevant location
and rename them to wpas_start_pno()/wpas_stop_pno().

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
2014-03-11 19:12:57 +02:00
Eduardo Abinader
b5008c2c2d tests: Fix trace parameter invocation
If trace-cmd command does not exist, run-tests.py could end up hanging
in a loop waiting for input. Fix this simply by checking whether the
trace-cmd command can be executed sucessfully and exiting the script if
not.

Signed-off-by: Eduardo Abinader <eduardo.abinader@openbossa.org>
2014-03-11 19:09:40 +02:00
Simon Wunderlich
1d91f504e4 hostapd: Process management frames only once per BSS
At least in nl80211, broadcast management frames like Probe Request
frames, may be processed multiple times per BSS if multi-BSS is active
and NL80211_CMD_FRAME event is used to deliver them. In the case of
Probe Request frames, hostapd will create multiple redundant Probe
Response frames which are problematic when many BSS are on one channel.

This problem is caused by driver_nl80211 generating an event for
wpa_supplicant_event() for each BSS, and hostapd_mgmt_rx() calls
ieee802_11_mgmt() for each BSS, too.

Fix this by processing broadcast events only for the BSS the driver
intended to. The behavior is not changed for drivers not setting a BSS.

Signed-hostap: Simon Wunderlich <simon@open-mesh.com>
2014-03-11 19:07:25 +02:00
Simon Wunderlich
e070051207 hostapd: Allow to switch to usable DFS channels
If channels are "available", change to "usable" DFS channels as a
fallback, too. This requires CAC, but it is still better to do that
instead of stopping service completely.

Signed-hostap: Simon Wunderlich <sw@simonwunderlich.de>
2014-03-11 19:04:15 +02:00
Simon Wunderlich
01b99998bd hostapd: Allow to switch to DFS channels if available
If DFS channels are marked as "available", an AP can switch to them
immediately without performing CAC. Therefore, the channel selection
function should consider these channels even though these are radar
channels.

Signed-hostap: Simon Wunderlich <sw@simonwunderlich.de>
2014-03-11 19:01:44 +02:00
Simon Wunderlich
70ee1be248 hostapd: Add config option chanlist for DFS channels
Different channels allow different transmission power, at least in ETSI
countries. Also, ETSI requires a "channel plan" for DFS operation, and
channels should be randomly choosen from these channels.

Add a channel list configuration option for users to add channels
hostapd may pick from.

Signed-hostap: Simon Wunderlich <sw@simonwunderlich.de>
2014-03-11 18:59:40 +02:00
Jouni Malinen
2ca47da4f7 tests: Fix trace-cmd output for host case
Both the output file path and the current working directory included the
log directory and this failed if log directory was not absolute (e.g.,
when using the default logs/current in the case a VM is not used).

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-11 17:04:33 +02:00
Jouni Malinen
09eef142ea Use internal FIPS 186-2 PRF if needed
Previously, EAP-SIM/AKA/AKA' did not work with number of crypto
libraries (GnuTLS, CryptoAPI, NSS) since the required FIPS 186-2 PRF
function was not implemented. This resulted in somewhat confusing error
messages since the placeholder functions were silently returning an
error. Fix this by using the internal implementation of FIP 186-2 PRF
(including internal SHA-1 implementation) with crypto libraries that do
not implement this in case EAP-SIM/AKA/AKA' is included in the build.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-11 16:44:22 +02:00
Jouni Malinen
9b3e2ad3a7 tests: Fix reporting of skipped cipher suite tests
The return value was lost and GCMP, CCMP-256, and GCMP-256 test cases
were reporting PASS instead of SKIP.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-11 15:03:38 +02:00
Jouni Malinen
3b9c5176d1 Fix PTK derivation for CCMP-256 and GCMP-256
Incorrect PTK length was used in PMK-to-PTK derivation and the Michael
MIC TX/RX key swapping code was incorrectly executed for these ciphers
on supplicant side.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-11 15:00:09 +02:00
Jouni Malinen
e6ef73f188 nl80211: Add debug print of KEY_DATA and KEY_SEQ
While these were already available from elsewhere in the debug log, it
is convenient to have the values also available at the location where
the actual nl80211 command is issued.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-11 14:59:15 +02:00
Jouni Malinen
8fc1f204df tests: HS 2.0 session information URL
Verify that session information is stored from Access-Accept and sent to
the station at the requested timeout. Verify that station processes this
notification.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-10 11:34:31 +02:00
Jouni Malinen
4056b0c747 tests: RADIUS Class attribute
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-10 11:16:29 +02:00
Jouni Malinen
18b92c6cfe tests: RADIUS attributes in Access-Request and Accounting-Request
This verifies that hostapd can add extra RADIUS attributes using
radius_auth_req_attr and radius_acct_req_attr.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-10 11:05:48 +02:00
Jouni Malinen
fe23f3816e tests: hostapd as P2P Device manager
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-10 10:58:01 +02:00
Jouni Malinen
f6e1eb07ee tests: Set country code and use 5 GHz band
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
2014-03-10 10:49:49 +02:00