Commit graph

376 commits

Author SHA1 Message Date
Arend van Spriel
5ddd07cb37 Reset normal_scans counter upon entering INTERFACE_DISABLED state
Depending on the implementation, the scheduled scan may not give results
quickly when in DISCONNECTED state. This patch resets
wpa_s::normal_scans upon entering to the INTERFACE_DISABLED state so a
normal scan is assured upon going to DISCONNECTED state after the
interface has been re-enabled. This mainly solves a long reconnect time
observed upon repeated kernel driver reloads, i.e., third reload
resulted in a scheduled scan.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-hostap: Arend van Spriel <arend@broadcom.com>
2014-01-17 11:48:17 +02:00
Jouni Malinen
c60ba9f7ab Skip network disabling on expected EAP failure
Some EAP methods can go through a step that is expected to fail and as
such, should not trigger temporary network disabling when processing
EAP-Failure or deauthentication. EAP-WSC for WPS was already handled as
a special case, but similar behavior is needed for EAP-FAST with
unauthenticated provisioning.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-08 16:42:15 +02:00
Jouni Malinen
b6a9590b34 Interworking: Keep up to two pending GAS_REQUEST responses
Previously, only the last response data was kept in memory. This
increases that to hold up to two last responses to allow some more
parallel operations to be requested. In addition, the response data is
now freed as soon as the external program has fetched it.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:12 +02:00
Jouni Malinen
1f965e622a Allow external programs to request wpa_radio work items
The new control interface command RADIO_WORK can be used by external
programs to request radio allocation slots from wpa_supplicant if
exclusive radio control is needed, e.g., for offchannel operations. If
such operations are done directly to the driver, wpa_supplicant may not
have enough information to avoid conflicting operations. This new
command can be used to provide enough information and radio scheduling
to avoid issues with such cases.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
6428d0a71f Do not start wpa_radio work during externally triggered scan
If an external program triggers a scan, wpa_supplicant does not have a
wpa_radio work item for this operation to protect against other
offchannel operations. This can result in operations failing, so try to
avoid damage by not starting any new wpa_radio work items during a scan
that was started by another process.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:10 +02:00
Jouni Malinen
6470f471e4 Remove unneeded scan delay on connection-in-progress
This type of protection against concurrent connection and scan
operations is now enforced through the wpa_radio work mechanism, so this
separate protection mechanism is not needed anymore.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
6ac4b15ef8 Use wpa_radio work for connection
This protects against conflicting offchannel operations during
connection (authentication, association, EAP exchanges, 4-way
handshake).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-07 10:45:09 +02:00
Jouni Malinen
1b5d4714dd Use radio work for P2P scan requests
Avoid concurrent P2P scan requests with any other exclusive use of the
radio by using the radio work queuing mechanism. This removes some of
the earlier workarounds that postponed scans depending on other
operations.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:39:25 +02:00
Jouni Malinen
d12a51b5d2 Use radio work for scan requests
Avoid concurrent scan requests by using the radio work queuing
mechanism.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:37:50 +02:00
Jouni Malinen
b1ae396f59 Add framework for exclusive radio operations
The new radio work item concept can be used to request time for an
operation that requires exclusive radio control, e.g., a scan. Once the
radio is available, the registered callback function will be called.
radio_work_done() must be called once the exclusive radio operation has
been completed, so that the radio is freed for other operations. The
special case of deinit=1 is used to free the context data during
interface removal. That does not allow the callback function to start
the radio operation, i.e., it needs to free the allocated resources
and return.

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-05 22:37:03 +02:00
Jouni Malinen
2f30cac36f Avoid unnecessary key clearing operations
Track set_key operations per-key index and clear keys on disconnection
only if the key was set (or may have been set which is the case for the
first operation after wpa_supplicant start).

Signed-hostap: Jouni Malinen <j@w1.fi>
2014-01-02 23:49:38 +02:00
Jouni Malinen
0187c41d88 Declare wpa_debug_* variables in src/utils/wpa_debug.h
These were somewhat more hidden to avoid direct use, but there are now
numerous places where these are needed and more justification to make
the extern int declarations available from wpa_debug.h. In addition,
this avoids some warnings from sparse.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 19:29:52 +02:00
Jouni Malinen
fcc61230d1 Declare wpa_drivers in src/drivers/driver.h
This avoids some warnings from sparse.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 19:19:37 +02:00
Jouni Malinen
4848a38d85 Get rid of duplicated cipher suite and AKM definitions
WPA_CIPHER_* and CIPHER_* are used for the exact same set of cipher
suites with the main difference being that the WPA_CIPHER_* version is
suitable to be used as a bitfield. Similarly, WPA_KEY_MGMT_* and
KEY_MGMT_* have similar design for AKMs. There is no need to maintain
two separate copies of the definitions since the bitfield compatible
version can be used for both needs. Get rid of the CIPHER_* and
KEY_MGMT_* versions to clean up the implementation by getting rid of
unnecessary mapping functions.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-31 09:16:27 +02:00
Jouni Malinen
db76aa64f1 Fix PeerKey 4-way handshake
The earlier changes to buffer EAPOL frames when not associated to avoid
race conditions (especially commit
3ab35a6603 but maybe something even before
that) broke PeerKey 4-way handshake. Fix this by using a separate check
before the race condition workaround to process PeerKey 4-way handshake
EAPOL-Key messages differently.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-28 16:32:54 +02:00
Jouni Malinen
fee5234284 Allow channel list to be specified for SCAN command
The new freq=<frequency ranges> parameter to the SCAN command can be
used to request a scan to be performed on the specified set of channels
instead of on all channels. For example, "wpa_cli scan
freq=2400-2500,5180" would scan channels 1-14 and 36. Only the channels
that the driver indicates as enabled and that are within the specified
ranges are included in the request.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-12-26 16:55:44 +02:00
Moshe Benji
ab41595f35 wpa_supplicant: Fix crash when terminating all interfaces
In wpa_supplicant_terminate_proc(), while iterating and
terminating interfaces, after an interface is terminated,
we can no longer access its memory as it is no longer valid
and causes a crash.

Fix this by saving the pointer to the next interface before freeing
the current one to avoid accessing an invalid memory location.

Signed-hostap: Moshe Benji <moshe.benji@intel.com>
2013-12-24 08:29:28 +02:00
Johannes Berg
4e1eae1dff wpa_supplicant: Use monotonic time for temp-disabled networks
Temporarily disabled networks are disabled for a certain
duration, so the code should use monotonic time.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 08:01:59 +02:00
Johannes Berg
c2be937ce7 wpa_supplicant: Use monotonic time for EAPOL RX workaround
The EAPOL RX workaround checks that the events are less than 100 ms
apart, so only uses relative times and should use monotonic time.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-12-24 07:35:42 +02:00
Eliad Peller
3727123269 bgscan: Stop bgscan only on disassociation
Stopping bgscan on any state other than COMPLETED results
in bgscan reset (stop + start) on every rekeying operation.

Signed-hostap: Eliad Peller <eliad@wizery.com>
2013-12-24 06:48:28 +02:00
Jouni Malinen
429dd9aff1 Advertise QoS Map support based on driver capability
Do not assume the driver supports QoS Mapping, but instead, advertise
support for this only if CONFIG_INTERWORKING is defined and driver
indicates support for configuring QoS Map.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-12-23 11:05:20 +02:00
Tomasz Bursztyka
b154a24e83 Fix a never-ending loop with multiple radios in wpa_supplicant
Commit 202dec2a94 introduced a never
ending loop for a case where a single wpa_supplicant process is used
with multiple radios. Fix this by advancing the iface pointer properly
to the next interface in the loop until a NULL pointer is hit.

Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2013-12-14 21:16:05 -08:00
Jithu Jance
8567866d75 P2P: Handle frequency conflict in single channel concurrency case
Based on priority, remove the connection with least priority whenever
a frequency conflict is detected.

Signed-hostap: Jithu Jance <jithu@broadcom.com>
2013-12-07 18:55:58 -08:00
Jouni Malinen
0ad3b9c402 Use wpa_radio data for get_shared_radio_freqs()
This replaces the now unnecessary iteration of get_radio_name() calls.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 21:20:15 +02:00
Jouni Malinen
1b544ffa74 Use wpa_radio data for wpas_wpa_is_in_progress()
This replaces the now unnecessary iteration of get_radio_name() calls.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 21:20:14 +02:00
Jouni Malinen
202dec2a94 Add shared per-radio structure for wpa_supplicant
struct wpa_radio is used as a shared data structure between all struct
wpa_supplicant instances that share the same physical radio.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 21:20:14 +02:00
Jouni Malinen
73c00fd794 Move wpa_supplicant driver initialization into a helper function
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-11-24 19:36:29 +02:00
Michael Schaller
bdec7ee5c9 D-Bus: Add support to set pkcs11_{engine,module}_path
Add SetPKCS11EngineAndModulePath D-Bus method. Add PKCS11EnginePath
and PKCS11ModulePath D-Bus property getters.

Signed-hostap: Michael Schaller <misch@google.com>
2013-11-23 10:48:27 +02:00
Masashi Honma
22cf7d7324 SCARD: Clean up SIM/USIM selection
Commit eb32460029 left an unneeded
sim_type argument to scard_init(). Remove that unnecessary argument to
clean up the implementation.

Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
2013-11-17 16:47:38 +02:00
Jouni Malinen
217cf4991d P2P: Add more debug prints for frequency selection
This prints out get_shared_radio_freqs() results and related information
from P2P operations to make debug logs more helpful for figuring out
issues related to multi-channel concurrency.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-11-05 11:07:51 +02:00
Ilan Peer
9804873e53 wpa_supplicant: Fix bug in get_shared_radio_freqs
The idx variable was mistakenly set to 0 at the beginning of the
interface iteration. This could result in the operating channel of the
interface calling the function from being removed from the returned
frequency array if other interfaces were operating.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
2013-11-05 10:55:22 +02:00
Haim Dreyfuss
3139270903 bgscan: Add global bgscan configuration
This option can be used to globally configure bgscan parameters
for all the network blocks.

Note that this configuration will not override a network block
specific bgscan settings, but will only be used in case that
the network block does not have a valid bgscan configuration.

Signed-hostap: Haim Dreyfuss <haim.dreyfuss@intel.com>
2013-11-05 10:26:31 +02:00
Jouni Malinen
4d9fb08d23 WPS: Clear known_wps_freq in addition to after_wps
Both of these variables can result in optimized WPS scans, so better
clear these more consistently to avoid unexpected single-channel scans.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-27 12:56:56 +02:00
Jouni Malinen
a2a535f897 Remove unnecessary wpa_s->conf checks
wpa_s->conf cannot be NULL because wpa_supplicant_init_iface() would not
allow wpa_supplicant_add_iface() to return wpa_s instance in such state.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-26 15:55:52 +03:00
Naresh Jayaram
07041c6f99 eap_proxy: Confirm eap_proxy initialization before reading SIM info
Trying to access the SIM card details without checking if the eap_proxy
layer has been initialized can results in a crash. Address this by
sending the request for the IMSI through eapol_supp_sm.c which can
verify that eap_proxy has been initialized.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-23 20:51:39 +03:00
Jouni Malinen
d259249762 Fix ENABLE_NETWORK not to reconnect in disconnected state
DISCONNECT followed by ENABLE_NETWORK ended up starting a scan for a new
connection due to wpa_supplicant_enable_one_network() setting
wpa_s->reassociate = 1. This was done regardless of wpa_s->disconnected
being 1 which should imply that wpa_supplicant should not try to connect
before asked explicitly with REASSOCIATE or RECONNECT.

Fix this by making ENABLE_NETWORK setting of reassociate = 1 and
starting of scans for connection conditional on wpa_s->disconnected ==
0. This will make ENABLE_NETWORK trigger a connection only if
wpa_supplicant is already in a state where it would try to connect if
there are any enabled networks.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-23 12:09:46 +03:00
Jouni Malinen
af8a827b90 Make frequency range list routines more general
This allows the frequency range list implementation to be shared for
other purposes.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-23 00:44:07 +03:00
Kyeyoon Park
c377514337 GAS: Delay GAS query Tx while scanning/connecting
Offchannel operations needed for a GAS query can conflict with ongoing
scan/connection progress, so delay GAS queries if such an operation is
in progress on the current interface or any virtual interface sharing
the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-21 13:15:45 +03:00
Jouni Malinen
a5d44ac083 EAP peer: Add framework for external SIM/USIM processing
The new configuration parameter external_sim=<0/1> can now be used to
configure wpa_supplicant to use external SIM/USIM processing (e.g., GSM
authentication for EAP-SIM or UMTS authentication for EAP-AKA). The
requests and responses for such operations are sent over the ctrl_iface
CTRL-REQ-SIM and CTRL-RSP-SIM commands similarly to the existing
password query mechanism.

Changes to the EAP methods to use this new mechanism will be added in
separate commits.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-10-20 13:12:04 +03:00
Jouni Malinen
56f5af489c Interworking: Add support for QoS Mapping functionality for the STA
Indicate support for QoS Mapping and configure driver to update the QoS
Map if QoS Map Set elements is received from the AP either in
(Re)Association Response or QoS Map Configure frame.

This commit adds support for receiving the frames with nl80211 drivers,
but the actual QoS Map configuration command is still missing.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-18 14:13:45 +03:00
Arif Hussain
8b3b803ab9 Include Extended Capabilities element based on scan results
Add Extended Capabilities element to association request only if the AP
included this element in Beacon/Probe Response frames. This is a
workaround to address interoperability issues with some older APs that
do not seem to be able to handle Extended Capabilities element in
(Re)Association Request frames.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-10-02 08:09:05 -07:00
Jouni Malinen
20625e9753 P2P: Remove P2P groups on process termination
Killing the wpa_supplicant process or using TERMINATE ctrl_iface command
resulted in the process existing without cleaning up possibly added
dynamic P2P group interfaces. Clean this up by stopping each P2P group
before stopping eloop.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-26 01:38:30 +03:00
Vinay Krishna Eranna
b2b688d18d P2P: Fix crash when failed to create GO interface
wpa_supplicant crashes if driver configuration for AP mode interface
configuration fails after group negotiation. This is because of a
regression from commit 1075b29571 that
ends up freeing the wpa_s instance from within
wpa_supplicant_create_ap() without the caller knowing.

Fix this by using an eloop timeout to free remove the P2P group so that
wpa_supplicant_create_ap() and especially wpa_supplicant_associate()
callers do not need to know about interface getting possibly removed. In
addition, move the P2P specific code into p2p_supplicant.c where it
really belongs. This allows the already existing group formation timeout
to be used by reducing the timeout to zero.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-09-03 12:43:12 +03:00
Jouni Malinen
01a57fe420 P2P: Maintain list of per-client PSKs for persistent groups
Record all generated per-client PSKs in the persistent group network
block and configure these for the GO Authenticator whenever re-starting
the persistent group. This completes per-client PSK support for
persistent groups.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-09-01 21:35:10 +03:00
Jouni Malinen
25a8f9e316 Clear EAPOL supplicant configuration info on current_ssid changes
There were some code paths that allowed obsolete configuration data
pointer to be maintained within EAPOL supplicant in case a network was
removed while not connection to it (i.e., wpa_s->current_ssid not
pointing to the network that was removed). This could result in use of
freed memory, e.g., from eap_sm_notify_ctrl_attached() when a new
control interface connected prior to the EAPOL supplicant configuration
pointer got updated.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-08-25 19:46:57 +03:00
Sean Lin
cbf41ca796 P2P: Do not delay retries on failure during group formation
4-way handshake may fail under extremely noisy environment and if this
happens during P2P group formation, the 10 second extra delay added in
wpas_auth_failed() can result in running over the 15 second timeout.

Avoid this by skipping the delay mechanism in wpas_auth_failed() for the
P2P group formation case. The P2P formation timeout will take care of
stopping the attempts if the failure condition does not get resolved.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-07-31 23:09:34 +03:00
Jouni Malinen
a21816a933 Use wpa_drv_shared_freq() if get_radio_name() is not supported
Some driver interfaces may not support the get_radio_name() design and
get_shared_radio_freqs() needs to be aware of such possibility when
determining shared radio frequencies.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-07-21 20:48:09 +03:00
Ilan Peer
53c5dfc2c4 Change share_vif_oper_freq() to handle multiple freqs
There are devices that can operate several channels concurrently.
Change shared_vif_oper_freq() to get_shared_radio_freqs() that can
return an array of frequencies currently used by all the virtual
interfaces that share the same radio.

In addition, move it to wpa_supplicant.c, so it can be used by other
modules.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-07-21 20:03:53 +03:00
Ilan Peer
4752147d88 nl80211: Report the number of concurrent support channels
Previously, drivers only reported if they support multiple concurrent
channels, but did not report the maximum number of supported channels.
Add this reporting to the driver capabilities and add the implementation
to driver_nl80211.

Signed-hostap: Ilan Peer <ilan.peer@intel.com>
Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-07-21 19:49:47 +03:00
Chengyi Zhao
831770bffe Cancel delayed scheduled scan when wpa_supplicant cleans up
Because a delayed scheduled scan will access the members of struct
wpa_supplicant which is freed and this can result in a crash,
wpa_supplicant needs to cancel delayed scheduled scan during cleanups.

Signed-hostap: Chengyi Zhao <chengyix.zhao@gmail.com>
2013-07-20 17:47:02 +03:00
Jouni Malinen
78f79fe5fc P2P: Do not add ctrl interface for P2P_DEVICE (p2p-dev-*)
Adding a new wpa_supplicant control interface for the dedicated
P2P_DEVICE would be quite confusing for programs that manage P2P
operations. Remove this control interface and require the global control
interface to be used since it will provide consistent interface for both
the new dedicated P2P_DEVICE (non-netdev) and old style P2P management
through a netdev.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-07-01 00:36:33 +03:00
Jouni Malinen
1c42b42f6c P2P: Fix TDLS and l2_packet init without P2P Device interface
Commit c68f6200a7 made these calls
conditional on !p2p_mgmt, but forced p2p_mgmt=1 for cases where the
driver does not use the dedicated P2P Device. Fix this by making the
!p2p_mgmt condition apply only if the driver does indicate use of a
dedicated P2P Device.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-06-30 20:02:25 +03:00
Arend van Spriel
c68f6200a7 P2P: Create P2P Device interface if supported
If the capability flag of the driver indicates a dedicated P2P Device is
supported, a P2P Device interface is created.

Create the P2P Device in main interface creation loop when the added
interface flags support and P2P supplicant is not yet initialized
avoiding recursion of add_interface.

Do not register l2_packet for P2P Device interface (both for EAPOL and
for TDLS).

Signed-hostap: Arend van Spriel <arend@broadcom.com>
2013-06-30 10:50:14 +03:00
Arend van Spriel
72950ed240 P2P: Remove a call to wpas_p2p_deinit_global()
In wpa_supplicant_deinit(), the function wpas_p2p_deinit_global()
was called. Remove it as it will be called from wpas_deinit_iface()
upon removal of the P2P management interface.

Signed-hostap: Arend van Spriel <arend@broadcom.com>
2013-06-25 13:56:28 +03:00
Jouni Malinen
ec7b97ab00 Interworking: Add support for using eap_proxy offload
Fetch IMSI through eap_proxy for Interworking network selection if
needed.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-06-19 18:42:17 +03:00
Jouni Malinen
dad153d16b Try to use fast-associate on ENABLE_NETWORK
This makes ENABLE_NETWORK behave similarily to SELECT_NETWORK by
allowing a scan to be skipped if recent scan results are available.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-22 16:10:59 +03:00
Jouni Malinen
2925756575 wpa_supplicant: Add -G argument to specify global ctrl group
The optional -G<group> command line argument can be used to specify the
group that can access the global control interface.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-18 11:00:05 +03:00
Vinayak Kamath
e27d20bb68 WNM: Add neighbor report processing for BSS Transition Management
Process the neighbor report received in BSS Management Request frames.

Signed-hostap: Vinayak Kamath <vkamat@codeaurora.org>
2013-05-16 17:48:59 +03:00
Jouni Malinen
e679f140b9 Mark interface disconnected on removal request
This cleans up debug log by not trying to process the disconnection
event as a failure that could result in blacklist addition and auto
connect attempt. These are pointless operations since the interface is
going to removed immediately after this.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-12 19:18:55 +03:00
Jouni Malinen
0cdb93fe9f Do not add BSS to blacklist on local disconnection request
There is no point in marking a BSS temporarily blacklisted based on a
connection failure or disconnection case if that happens as a result of
a local request to disconnect. The blacklist entry could result on
unexpected BSS getting selected on the next connection attempt. In
addition, the code to try to find another BSS within the ESS could
result in scanning a single channel on the next attempt. Fix these
issues by handling the connection failure events only if we are not in
disconnected state (i.e., would try to reconnect after this
automatically).

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-12 19:18:55 +03:00
Deepthi Gowri
36b9883d84 Defer scan if connection is in progress on any of the shared interfaces
Scanning can delay concurrent operations considerably, so it is better
to avoid that while trying to connect on any of the virtual interfaces
that share the same radio.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-10 16:10:50 +03:00
Jouni Malinen
6ea1f4135b Try to set WPA-None key after IBSS-joined event
cfg80211 rejects the set_key operations before the IBSS network has been
fully formed, so add one more attempt to set the key for WPA-None at
IBSS joined driver event.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-07 18:14:56 +03:00
Jouni Malinen
66562e9c75 Use cached driver capabilities instead of new fetch for each operation
There is no need to repeat the driver capability fetch for each
operation since we already cache driver flags in wpa_s->drv_flags.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-05-07 17:36:40 +03:00
Jouni Malinen
55a2df4389 HS 2.0: Include HS 2.0 Indication element only for HS 2.0 association
The Hotspot 2.0 specification seems to mandate this element to be
included in all (Re)Association Request frames if the station is Hotspot
2.0 capable. However, that results in conflicts with other requirements
like no TKIP use when this element is present. The design is really
supposed to include the indication element only for Hotspot 2.0
associations regardless of what the current specification implies.
Remove the HS 2.0 Indication element from (Re)Association Request frame
whenever the connection is not for Hotspot 2.0 purposes.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-05-05 16:29:21 +03:00
Jouni Malinen
dd57970477 Disable network temporarily on repeated connection failures
Previously, only explicit indications of authentication failures were
used to disable a network block temporarily. Extend this to use multiple
failed connection attempts as a sign of a possible authentication or
authorization failure to reduce the frequency of connection attempts
with a network that does not seem to allow connection.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-04-25 17:28:50 +03:00
Jouni Malinen
18e00b5e4d Move wpa_s freeing into wpa_supplicant_deinit_iface()
All wpa_supplicant_deinit_iface() callers ended up freeing wpa_s
immediately after this call. Move os_free(wpa_s) into the deinit
function to share the same call and make the deinit sequence clearer.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-04-23 18:07:41 +03:00
Dmitry Shmidt
e6304cad47 wpa_supplicant: Add option -I for additional config file
This option can be used only for global parameters that are not going
to be changed from settings.

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Iliyan Malchev <malchev@google.com>
2013-04-23 17:38:57 +03:00
Jouni Malinen
3db5439a5f Optimize Extended Capabilities element to be of minimal length
Leave out zero octets from the end of the element.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-31 21:58:17 +03:00
Johannes Berg
8cd6b7bce8 hostapd/wpa_s: Use driver's extended capabilities
Some extended capabilities (I'm currently interested in "Operating Mode
Notification" for VHT) are implemented by the kernel driver and exported
in nl80211. Use these in hostapd/wpa_supplicant.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-03-31 21:51:44 +03:00
Jouni Malinen
f85f545e71 P2P: Use common function for re-starting P2P scan after station scan
Make the implementation more consistent and cleaner by using a single
function for addressing all the cases where completion of a station mode
scan operation allows a P2P operation (search) to be re-started.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-18 17:32:31 +02:00
Partha Narasimhan
b2a12c4f93 wpa_supplicant: Fix lookup of cached PMKSA
This fixes the lookup of a usable PMKSA entry in the cache. Using
wpa_s->current_ssid often returns nothing when a usable PMKSA exists in
the cache since wpa_s->current_ssid does not necessarily point to the
correct network entry at this point in time (prior to association).

Signed-hostap: Partha Narasimhan <parthan@gmail.com>
2013-03-16 12:45:31 +02:00
Solomon Peachy
7d37a357fa Fix build without CONFIG_CTRL_IFACE or CONFIG_NO_STDOUT_DEBUG
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
2013-03-16 12:07:18 +02:00
Jouni Malinen
dbca75f82a P2P: Remove persistent group peer if it rejects invitation
If a peer replies to persistent group invitation with status code 8
(unknown group), remove the peer from the p2p_client_list if we are the
GO or remove the persistent group if we are the P2P client since it
looks like that the peer has dropped persistent group credentials and
the provisioning step needs to be executed again.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-03-15 16:43:06 +02:00
Johannes Berg
e9ee8dc394 wpa_supplicant: Support VHT capability overrides
Add support for VHT capability overrides to allow testing connections
with a subset of the VHT capabilities that are actually supported by
the device. The only thing that isn't currently supported (by mac80211
and this code) is the RX/TX highest rate field.

Signed-hostap: Johannes Berg <johannes.berg@intel.com>
2013-03-10 18:04:39 +02:00
David Spinadel
725fc39e07 wpa_supplicant: Reschedule sched scan after network change
Stop sched scan, if running, after any disabling or removing of
a network, and request a new scan if needed.

Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-03-10 17:51:13 +02:00
Jouni Malinen
14f7907890 Remove unnecessary local variable
The ssid parameter (if NULL) can be used for the loop, too, to make the
code look a bit prettier.

Signed-hostap: Jouni Malinen <j@w1.fi>
2013-03-10 17:45:15 +02:00
David Spinadel
dca1a51149 wpa_supplicant: Handle enabling of one or all networks equally
Move enabling a network to a separate function. Try to reconnect if not
associated to an AP. Abort scheduled scan in any case of a new scan.

Signed-hostap: David Spinadel <david.spinadel@intel.com>
2013-03-10 17:43:00 +02:00
Masashi Honma
5e24beae02 Use scan results for reconnection
This patch uses existing scan results for fast connection on REASSOCIATE
and RECONNECT commands.

Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
2013-02-28 16:34:08 +02:00
Sunil Dutt
7b44ff2c21 TDLS: Tear down peers when disconnecting from the AP
A TDLS Teardown frame with Reason Code 3 (Deauthenticated because
sending STA is leaving (or has left) IBSS or ESS) shall be transmitted
to all TDLS peer STAs (via the AP or via the direct path) prior to
transmitting a Disassociation frame or a Deauthentication frame to the
AP.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2013-02-13 01:19:44 +02:00
Paul Stewart
cecdddc184 wpa_supplicant: Implement fast-associate on SelectNetwork
If scan results are available when we perform a SelectNetwork, use
them to make an associate decision.  This can save an entire scan
interval-worth of time in situations where something external to
wpa_supplicant (like a connection manager) has just previously
requested a scan before calling SelectNetwork.

Signed-hostap: Paul Stewart <pstew@chromium.org>
2013-02-03 21:08:31 +02:00
Pontus Fuchs
9e737f08d4 Update scan interval gracefully
When the scan interval is changed the new interval is effective
after the old interval timer fires off one last time. This can cause
an unacceptable long delay when updating the interval.

Change this behaviour to use MIN(left of old interval, new interval)
for the scan interval following the interval change.

Signed-hostap: Pontus Fuchs <pontus.fuchs@gmail.com>
2013-02-03 18:14:05 +02:00
Jouni Malinen
62769a88db Move cipher to enum wpa_cipher conversion into wpa_common.c
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-13 18:02:20 +02:00
Jouni Malinen
edbd2a191e Move cipher suite selection into common helper functions
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-13 16:58:54 +02:00
Jouni Malinen
e056f93e60 Update copyright notices to include year 2013
Signed-hostap: Jouni Malinen <j@w1.fi>
2013-01-12 17:51:53 +02:00
Jouni Malinen
1cfc678723 Remove reassociated_connection variable
This was used to select between "(auth)" and "(reauth)" in
CTRL-EVENT-CONNECTED events. However, the variable was not cleared
anywhere else apart from the AP deinit case. As such, it did not really
provide correct information and is not really of much use even with
proper clearing added. As such, it is cleaner to just get rid of this
altogether.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-25 19:51:04 +02:00
Jouni Malinen
2049a875bc WNM: Additional BSS Transition Management capability
Add some more functionality for BSS Transition Management:
- advertise support for BSS Transition Management in extended
  capabilities element
- add hostapd.conf parameter bss_transition=1 for enabling support
  for BSS Transition Management
- add "hostapd_cli disassoc_imminent <STA> <num TBTTs>" for sending
  disassociation imminent notifications for testing purposes
- wpa_supplicant: trigger a new scan to find another BSS if the
  current AP indicates disassociation imminent (TODO: the old AP needs
  to be marked to use lower priority to avoid re-selecting it)

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-22 20:27:30 +02:00
Jouni Malinen
03e47c9c3a Share a single function for building extended capabilities element
This makes it easier to update extended capabilities for all uses
within wpa_supplicant.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-12-22 19:17:15 +02:00
Jouni Malinen
3ab35a6603 Extend EAPOL frames processing workaround for roaming cases
Commit 1ff733383f added a mechanism to
work around issues due to association events and EAPOL RX events being
getting reordered. However, this applied only for the case where
wpa_supplicant is not in associated state. The same issue can happen in
roaming case with drivers that perform BSS selection internally (or in
firmware). Handle that case similarly by delaying received EAPOL frame
processing if the source address of the EAPOL frame does not match the
current BSSID.

Since wired IEEE 802.1X do not have BSSID, make this additional
workaround conditional on BSSID match having been observed during the
previous association.

This fixes issues where the initial EAPOL frame after reassociation was
either dropped (e.g., due to replay counter not increasing) or replied
to with incorrect destination address (the BSSID of the old AP). This
can result in significantly more robust roaming behavior with drivers
that do not use wpa_supplicant for BSS selection.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-21 21:35:35 +02:00
Ben Greear
a90497f85f wpa_supplicant: Allow user to disable short guard interval (SGI)
Requires Linux kernel patch to make the SGI-20 properly disabled. SGI-40
will already work since Linux 3.4 or so.

Signed-hostap: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
2012-12-18 14:45:09 +02:00
Jouni Malinen
e6955ba9f9 WNM: Add WNM-Sleep Mode into Extended Capabilities element
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-12-16 12:45:59 +02:00
Jouni Malinen
9796a86c23 Use a shared function for requesting a new connection
Both the ctrl_iface and D-Bus interface use similar functionality to
request a new connection. Combine these to a single function to avoid
need to maintain duplicated implementation.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-25 16:30:30 +02:00
Jouni Malinen
f1a5263389 Maintain maximum blacklist count over list clear operations
wpas_connection_failed() uses the blacklist count to figure out a
suitable time to wait for the next scan. This mechanism did not work
properly in cases where the temporary blacklist gets cleared due to no
other BSSes being available. Address this by maintaining an additional
count of blacklisting values over wpa_blacklist_clear() calls. In
addition, add one more step in the count to timeout mapping to go to 10
second interval if more than four failures are seen.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-25 16:20:44 +02:00
Jouni Malinen
4115303bbe Document wpa_s->scan_req
Use an enum with documented values to make it easier to understand how
wpa_s->scan_req is used.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-25 15:55:32 +02:00
Jouni Malinen
62d4980331 Allow PMF to be enabled by default
Previously, PMF (protected management frames, IEEE 802.11w) could be
enabled only with a per-network parameter (ieee80211w). The new global
parameter (pmf) can now be used to change the default behavior to be PMF
enabled (pmf=1) or required (pmf=2) for network blocks that do not
override this with the ieee80211w parameter.

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-11-24 22:21:29 +02:00
Jouni Malinen
6e2020210a Allow OKC to be enabled by default
Previously, OKC (opportunistic key caching, a.k.a. proactive key
caching) could be enabled only with a per-network parameter
(proactive_key_caching). The new global parameter (okc) can now be used
to change the default behavior to be OKC enabled (okc=1) for network
blocks that do not override this with the proactive_key_caching
parameter.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-12 20:07:53 +02:00
Jouni Malinen
1e8a6e7553 Remove unused wpa_supplicant_disassociate()
This function is now unused after the last couple of commits that
removed the last uses, so remove this to keep code simpler since all
places that disassociate, can use deauthentication instead.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-05 17:05:37 +02:00
Jouni Malinen
07783eaaa0 Use deauthentication instead of disassociation if not associated
cfg80211/mac80211 may reject disassociation command if association has
not yet been formed. Use deauthentication in cases where it is possible
that we are associating at the moment the command is issued.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-05 16:58:00 +02:00
Jouni Malinen
42d235477f Use wpa_drv_{disassociate,deauthenticate} while waiting for connection
wpa_supplicant_{disassociate,deauthenticate}() need to inform the driver
about decision to disconnect even if this happens during the time when
the driver is still trying to complete association. During that time,
wpa_s->bssid is not set, so the code in these functions needs to figure
out the correct BSSID based on that field or wpa_s->pending_bssid. In
addition, it is possible that the BSSID is not even known at
wpa_supplicant at this point in time when using drivers that perform BSS
selection internally. In those cases, the disconnect command needs to be
sent to the driver without the BSSID.

This fixes issues where the driver (or cfg80211 in particular) may be
left in mismatching state with wpa_supplicant when disconnection (e.g.,
due to a ctrl_iface command) happens between connection request and
association event.

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-11-05 16:57:57 +02:00
Jouni Malinen
c10347f246 Add initial parts for SAE
This introduces new AKM for SAE and FT-SAE and adds the initial parts
for going through the SAE Authentication frame exchange. The actual SAE
algorithm and new fields in Authentication frames are not yet included
in this commit and will be added separately. This version is able to
complete a dummy authentication with the correct authentication
algorithm and transaction values to allow cfg80211/mac80211 drivers to
be tested (all the missing parts can be handled with
hostapd/wpa_supplicant changes).

Signed-hostap: Jouni Malinen <j@w1.fi>
2012-09-30 19:51:07 +03:00
Jouni Malinen
6407f4132f Add disallow_aps parameter to disallow BSSIDs/SSIDs
External programs can use this new parameter to prevent wpa_supplicant
from connecting to a list of BSSIDs and/or SSIDs. The disallowed BSSes
will still be visible in scan results and it is possible to run ANQP
operations with them, but BSS selection for connection will skip any
BSS that matches an entry in the disallowed list.

The new parameter can be set with the control interface SET command
using following syntax:

SET disallow_aps <disallow_list>
disallow_list ::= <ssid_spec> | <bssid_spec> | <disallow_list> | “”
SSID_SPEC ::= ssid <SSID_HEX>
BSSID_SPEC ::= bssid <BSSID_HEX>

For example:
wpa_cli set disallow_list "ssid 74657374 bssid 001122334455 ssid 68656c6c6f"
wpa_cli set disallow_list
(the empty value removes all entries)

Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
2012-09-27 17:36:59 +03:00