Previously, both this and combination of OUI_WFA and P2P_OUI_TYPE were
used. Using the full 32-bit value as a single operation saves a bit in
code size, so start moving towards using it more consistently when
writing or finding the P2P vendor specific element.
Signed-off-by: Rahul Jain <rahul.jain@samsung.com>
Suppose we have multiple peers and we have peers advertising SD
capability, but no services registered for advertising. In this case,
even if there are multiple broadcast queries set, we might end up
sending only the lastly added broadcast query to the same device (since
SD_INFO won't get set for the first broadcast query). Add support for
multiple wildcard queries to be tracked to enable this type of use
case.
Some times it is seen that before advancing to next device in the list,
the scan results come and update SD_SCHEDULE flag. This will result in
sending the already sent query to the same device without giving chance
to other devices. This issue again is seen with peer devices advertising
SD capability without any services registered.
Signed-off-by: Jithu Jance <jithu@broadcom.com>
Replace direct wpa_msg() calls with p2p_dbg(), p2p_info(), and p2p_err()
calls that use a new debug_print() callback to handle actual debug
printing outside the P2P module.
Signed-hostap: Jouni Malinen <j@w1.fi>
All P2P use cases are required to use the global operating table and
there is no need to need to try to maintain some backwards compatibility
with country code -specific values. Clean up the implementation by
removing the unnecessary country parameter.
Signed-hostap: Jouni Malinen <j@w1.fi>
wpa_cli p2p_serv_disc_req command can now be used to request WSD
request to be sent to specified or all peers who support WSD.
format: wifi-display <list of roles> <list of subelements>
examples:
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source] 2,3,4,5
p2p_serv_disc_req 02:01:02:03:04:05 wifi-display [pri-sink] 3
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [sec-source] 2
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source+sink] 2,3,4,5
p2p_serv_disc_req 00:00:00:00:00:00 wifi-display [source][pri-sink] 2,3,4,5
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
This patch adds a check of the return value of wpabuf_dup() in a large
Service Discovery Response.
Signed-hostap: Masashi Honma <masashi.honma@gmail.com>
Unlike the unicast SD queries, the queries directed to all peers depend
on P2P_DEV_SD_INFO flag being cleared to allow the query to be sent to
a peer that has previously replied to any SD query.
Signed-hostap: Jouni Malinen <jouni@qca.qualcomm.com>
Remove the GPL notification text from files that were initially
contributed by Atheros Communications or Qualcomm Atheros.
Signed-hostap: Jouni Malinen <j@w1.fi>
GAS/ANQP is a generic protocol and in no way specific to P2P, so move
routines used to build GAS/ANQP frames to a separate file that can be
shared for other uses than just P2P service discovery.
This embeds some information about each P2P peer that will be publically
visible in a struct that is shared.
The dev_found notification function is also passed the new struct, which
requires some work for the driver-based P2P management.
Signed-off-by: Konguraj(Raj) Kulanthaivel <konguraj.kulanthaivel@intel.com>
Signed-off-by: Fabien Marotte <fabienx.marotte@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to avoid confusing the driver with a new remain-on-channel
request, delay sending of a new Action frame if the driver indicates
Action frame RX diromg a scan.
P2P specification v1.15 fixed the description of the GAS fragmentation
to not duplicate NQP Query Response Field header in all fragments. This
change makes the fragmentation match with the description in IEEE
802.11u. The change is not backwards compatible with previous P2P
specification versions as far as fragmented SD responses are concerned.
